001 Hak Akses (open/membership)membership
700 Entri Tambahan Nama OrangAdi Surjosatyo, supervisor; Tobing, Sheila, supervisor; Mohammad Akita Indianto, examiner; Saragih, Agung Shamsuddin, examiner; Hasbi Priadi, examiner
336 Content Typetext (rdacontent)
264b Nama PenerbitFakultas Teknik Universitas Indonesia
710 Entri Tambahan Badan KorporasiUniversitas Indonesia. Fakultas Teknik
504 Catatan Bibliografipages 74-76
049 No. Barkod15-25-08227315
852 LokasiPerpustakaan UI
338 Carrier Typeonline resource (rdacarrier)
590 Cat. Sumber Pengadaan KoleksiDeposit
903 Stock Opname
534 Catatan Versi Asli
Tahun Buka Akses2025
053 No. Induk15-25-08227315
653 Kata Kuncigasification; reliability; RCM; mobile biomass gasifier P3; suction blower; vibrating grate; rotary feeder
040 Sumber PengataloganLibUI ida rda
245 Judul UtamaOptimasi Keandalan Mobile Biomass Gasifier (Prototype 3) Plant dengan Perhitungan Distribusi Weibull sebagai Dasar Penyusunan Jadwal Kegiatan Preventive Maintenance Berbasis Reliability Centered Maintenance (RCM) = Reliability Optimization of Mobile Biomass Gasifier (Prototype 3) Plant with Weibull Distribution Calculation as Basis for Preparing the Schedule of Preventive Maintenance Activities Based on Reliability Centered Maintenance (RCM)
264c Tahun Terbit2025
650 Subyek TopikRice husks; Biomass energy.
850 Lembaga PemilikUniversitas Indonesia
520 Ringkasan/Abstrak/IntisariMesin Mobile Biomass Gasifier (P3) merupakan suatu mesin yang diharapkan mampu memanfaatkan limbah sekam padi menjadi sumber energi dengan kapasitas 25kWth. Pemakaian dalam jangka waktu tertentu akan berdampak pada penurunan fungsi atau ketahanan pakai sehingga diperlukan suatu metode perawatan yang optimal agar mesin mampu melakukan fungsinya sesuai yang diinginkan atau memiliki keandalan yang tinggi. Peralatan kritis yang menjadi bad actor dan perlu segera diatasi agar tetap mempertahankan keandalan adalah Suction blower, Vibrating Grate dan Rotary feeder. Berdasarkan hasil analisis kualitatif dan kuantitatif dengan pendekatan RCM, untuk mencapai target R(t) pada sistem Mobile Biomass Gasifier (P3) sebesar 0,6, maka jenis perawatan diterapkan pada sistem Suction blower adalah restoration task dengan cleaning pada pipa setiap 5 jam, on condition task pada motor - blower serta analisis vibrasi dan temperatur setiap 5 jam, restoration task dengan lubrikasi pada bearing setiap bulan dan function test pada kontrol panel setiap 10 jam. Pada Vibrating grate adalah restoration task dengan cleaning pada grate setiap 10 jam, on condition task dengan analisis temperatur pada motor setiap 10 jam dan restoration task dengan lubrikasi pada bearing setiap bulan. Pada Rotary feeder adalah restoration task dengan cleaning pada rotor setiap 10 jam, on condition task dengan analisis temperatur pada motor setiap 10 jam dan restoration task dengan lubrikasi pada bearing setiap bulan dan function test pada kontrol panel setiap 10 jam. ......The Mobile Biomass Gasifier (P3) machine is a machine that is expected to be able to utilize rice husk waste as a source of energy with a capacity of 25 kWth. Usage over a certain period of time will have an impact on decreasing function or durability, so an optimal maintenance method is needed so that the machine is able to perform its functions as desired or has high reliability. Critical equipment that is a bad actor and needs to be addressed immediately to maintain reliability is the Suction blower, Vibrating Grate and Rotary feeder. Based on the results of qualitative and quantitative analysis with the RCM approach, to achieve the target R(t) on the Mobile Biomass Gasifier (P3) system of 0.6, So the type of maintenance that will be applied to the Suction blower system is a restoration task with cleaning the pipe every 5 hours. on condition task on motor-blower with vibration and temperature analysis every 5 hours, restoration task with lubrication on bearings every month and function test on control panel every 10 hours. On the Vibrating grate is a restoration task with cleaning the grate every 10 hours, on condition task with temperature analysis on the motor every 10 hours and restoration task with lubrication on the bearings every month. On the Rotary feeder is a restoration task with cleaning the rotor every 10 hours, on condition task with temperature analysis on the motor every 10 hours and restoration task with lubrication on the bearings every month and function test on the control panel every 10 hours.
904b Pemeriksa Lembar KerjaAdhityaN-Agustus2025
090 No. Panggil SetempatT-pdf
d-Entri Utama Nama Orang
500 Catatan UmumDapat diakses di UIANA (lib.ui.ac.id) saja.
337 Media Typecomputer (rdamedia)
d-Entri Tambahan Nama Orang
526 Catatan Informasi Program StudiTeknik Sistem Energi
100 Entri Utama Nama OrangWahyu Dwi Kurniady, author
264a Kota TerbitDepok
300 Deskripsi Fisikxiii, 76 pages : illustration + appendix
904a Pengisi Lembar KerjaAdhityaN-Agustus2025
Akses Naskah Ringkas
856 Akses dan Lokasi Elektronik
502 Catatan Jenis KaryaTesis
041 Kode Bahasaind