Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 143262 dokumen yang sesuai dengan query
cover
Herlina Ichlas
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 1991
S28029
UI - Skripsi Membership  Universitas Indonesia Library
cover
Khairul Umam
"Penelitian ini bertujuan untuk memperkirakan komposisi terbaik PVC - diocthyl phtalate (DOP). Resin PVC ASNYL_ digunakan dengan variasi penambahan DOP sebesar 0, 2, 4, 6, 8, dan 10 phr. Spesimen dibuat melalui calendering dan dicetak dengan hot pressing. Dari hasil penelitian, diketahui bahwa seiring dengan penambahan konsentrasi DOP nilai MFR meningkat dari 5,7 gr/10 menit pada saat 0 phr sampai 28,2 gr/10 menit pada 10 phr. Kecepatan gelation time cenderung meningkat dari 1,66 menit pada 0 phr menjadi 1,46 menit pada 10 phr. Kandungan DOP yang lebih tinggi juga cenderung menurunkan kekerasan dari 25,4 shore A pada 0 phr, menjadi 24.5 shore A pada 10 phr. Ketahanan impak dari PVC menunjukkan penurunan dari 1285 J/m untuk 0 phr dan turun menjadi 214 J/m pada 10 phr. Fenomena penurunan ketahanan impak ini disebabkan karena terjadinya efek anti-plastisasi pada penambahan DOP kurang dari 15 phr yang justru menyebabkan PVC menjadi getas. Semua formulasi yang diberikan memberikan hasil yang kurang signifikan antara satu sama lain namun dengan mepertimbangkan pengaruh terbaik, sebaiknya dipilih formulasi 10 phr.

The objective of this research is to predict the best PVC ' diocthyl phthalate (DOP) formulation. The sample used is PVC ASNYL_ resins by varying the content of diocthyl phtalate which are; 0, 2, 4, 6, 8 and 10 phr. Specimen made by calendaring process and pressed by hot pressing method. It was observed that the increasing content of diocthyl phthalate resulting the increasing of melt flow rate from 5,7 gr / 10 minutes at 0 phr to 28,2 gr /10 minutes at 10 phr. Gelation time rate increase from 1,66 minutes at 0 phr to 1,46 minutes at 10 phr. the increasing content of DOP resulting the decreasing of hardness from 25,4 shore A at 0 phr, to 24.5 shore A at 10 phr. Impact resistance decrease from 1285 J/m at 0 phr to 214 J/m at 10 phr. The decreasing phenomenone of impact resistance is caused by anti-plastication effect when the DOP less than 15 phr. All formulation give not significantly influence of addition but by considering the best influence, it is better to use 10 phr formulation."
Depok: Fakultas Teknik Universitas Indonesia, 2009
S51487
UI - Skripsi Open  Universitas Indonesia Library
cover
Ratih Andalusi
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2006
TA1508
UI - Tugas Akhir  Universitas Indonesia Library
cover
Ratih Azsarinka
"Salah satu jenis polimer alam, selulosa yang terkandung dalam kulit jagung, dapat digunakan sebagai bahan dasar bioplastik. Tepung pati jagung maizena dengan penguat kulit jagung berukuran butir tertentu disintesis bersama kitosan dan gliserol. Bioplastik yang dihasilkan berbentuk lembaran tipis berwarna cokelat keruh. Perubahan ukuran butir dari 150 mesh menjadi 200 mesh mengubah sifat bioplastik, khususnya sifat mekanik.
Diperoleh bioplastik terbaik dengan ukuran butir 200 mesh dan komposisi kitosan 0,04 dengan kuat tarik sebesar 286,31 N/cm2, elongasi sebesar 10,19 , modulus Young sebesar 28,11 N/cm2, dan ketahanan sobek sebesar 705,61 mN. Terjadi pergeseran bilangan gelombang dan perubahan gugus fungsi pada bioplastik. Terhadap lingkungan, bioplastik mengalami degradasi sebesar 35 selama 21 hari di dalam tanah dan mulai berjamur setelah 10 hari berada dalam udara terbuka, serta mampu bertahan pada suhu 100°C selama satu jam.

One kind of biopolymer that can be used as primary materials for bioplastics is cellulose in corn husk. Corn starch powder maize with corn husk filler in different grain size is then synthesized with chitosan and glycerol. The resulting bioplastics is thin film in form with muddy brown color. Alterating the powder grain size from 150 mesh to 200 mesh modifies the physical characteristics, especially mechanical properties.
The most optimal bioplastics were obtained with 200 mesh grain size and 0.04 wt chitosan composition with tensile strength of 286.31 N cm2, elongation of 10.19, Young modulus of 28.11 N cm2 and tear resistance of 705.61 mN. There are shifts in peak absorbance wavenumber and changes in some functional groups. To the environment, bioplastics were degraded 35 for 21 days in soil and started moldy after 10 days in open air, as well as endured for one hour in temperature 100°C.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2017
S68532
UI - Skripsi Membership  Universitas Indonesia Library
cover
Yuanita Meilani
"Komposit sandwich merupakan salah satu material yang berpotensi untuk diterapkan sebagai material penyusun rancang bangun struktur ringan. Telah dilakukan penelitian mengenai sifat mekanik pada komposit sandwich woven S-glass/epoxy dengan inti Polyvinyl chloride foam. Komposit sandwich, yang terdiri dari dua jenis yaitu 00/900/PVC/00/900 dan 00/900/PVC/-450/450, dibuat dengan menggunakan metode hand lay-up, diikuti dengan metode vacuum bagging. Pengukuran massa jenis, pengujian mekanik berupa uji tekuk tiga titik dan uji tekan untuk mengetahui sifat mekanik komposit sandwich ini, serta pengamatan kerusakan menggunakan Scanning Electron Microscope dilakukan. Didapatkan massa jenis yang relatif kecil untuk kedua komposit sandwich, yaitu (0.20 ± 0.01) gr/cm3 dan (0.21 ± 0.01) gr/cm3. Sifat mekanik terbaik didapatkan pada komposit sandwich 00/900/PVC/00/900 dengan kekuatan tekuk, kekuatan geser, dan kekuatan tekan sebesar (51.04 ± 2.49) MPa, (0,39 ± 0.02) MPa dan (4.79 ± 0.12) MPa. Moda kegagalan yang terjadi adalah indentation dan buckling dengan kerusakan pada kulit dan inti.

Sandwich composites are materials that have potential to be used in lightweight structure design. A research on the mechanical properties of a woven S-glass/epoxy sandwich with polyvinyl chloride foam core has been done. The sandwich composites were classified into two types, 00/900/PVC/00/900 and 00/900/PVC/-450/450 and were manufactured with hand lay-up method, followed by vacuum bagging method. Density measurement, three-point bending test, edgewise compression test, and failure observation with Scanning Electron Microscope (SEM) were conducted. Relatively small densities were achieved for these two sandwich composites, (0.20 ± 0.01) gr/cm3 and (0.21 ± 0.01) gr/cm3. The best mechanical properties were obtained in sandwich composite 00/900/PVC/00/900 , with flexural strength, core shear strength, and compression failure stress of (51.04 ± 2.49) MPa, (0,39 ± 0.02) MPa, and (4.79 ± 0.12) MPa. Mode of failure that occured is indentation and buckling with damage to the skin and core."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2014
S57079
UI - Skripsi Membership  Universitas Indonesia Library
cover
Universitas Indonesia, 1997
S28269
UI - Skripsi Membership  Universitas Indonesia Library
cover
Iding Jahidin
Depok: Fakultas Teknik Universitas Indonesia, 2002
S41419
UI - Skripsi Membership  Universitas Indonesia Library
cover
cover
Bimo Ary Pujangga Putra
"ABSTRAK
Plastik sebagai bahan kemasan dan coating mengalami peningkatan global setiap tahun. Ini menimbulkan masalah serius bagi lingkungan karena sulitnya terdegradasi. Salah satu solusi untuk mengatasi masalah limbah plastik adalah penggunaan bioplastik. Untuk meningkatkan sifat mekanik dari bioplastik, biokomposit yang dibuat dengan penambahan aditif dan pengisi tertentu. Tujuan dari penelitian ini adalah untuk mengetahui pengaruh Butil Benzyl Phthalate plasticizer BBP dan Seng Oksida ZnO nanopartikel terhadap sifat mekanik dan termal biokomposit selulosa asetat butirat CAB / organoclay.Nanopartikel ZnO disintesis dari prekursor ZnO komersial melalui metode reduksi ukuran sol-gel menggunakan asam sitrat. Seng sitrat dikalsinasi pada suhu 600oC. ZnO nanopartikel dengan ukuran rata-rata 44,4 nm diperoleh pada rasio seng nitrat 1:2 terhadap asam sitrat. Film biokomposit dibuat dengan menggunakan metode solution casting dengan aseton sebagai pelarut. Penambahan plasticizer BBP dan nanopartikel ZnO sebesar masing-masing 30 dan 10 membuat biokomposit memiliki nilai kekuatan tarik 2,22 MPa. Pergeseran nilai suhu transisi gelas Tg selulosa asetat butirat tidak dapat terlihat dikarenakan homogenitas biokomposit saat proses casting.

ABSTRACT
Plastics as packaging materials and coatings have increased globally every year. This poses a serious problem for the environment because of the difficulty to degrade. One solution to overcome the problem of plastic waste is the use of bioplastics. To improve the mechanical properties of bioplastics, biocomposites are fabricated with the addition of certain additives and fillers. The purpose of this study was to determine the effect of plasticizer Butyl Benzyl Phthalate BBP and Zinc Oxide ZnO nanoparticles to the mechanical and thermal properties of biocomposite cellulose acetate butyrate CAB organoclay.ZnO nanoparticles were synthesized from a commercial ZnO precursor through sol gel method to reduce the size using citric acid. Zinc citrate was calcined at a temperature of 600oC. ZnO nanoparticles with an average size of 44.4 nm were obtained at a mole ratio of zinc nitrate citric acid was 1 2. Biocomposite films were made by solution casting method using acetone as the solvent. The addition of plasticizer BBP and ZnO nanoparticles by 30 and 10 respectively in the biocomposites produced a tensile strength of 2,223 MPa. Shifting value of the glass transition temperature Tg of cellulose acetate butyrate could not been observed due to the homogeneity of the biocomposite during the process of casting."
2017
T48360
UI - Tesis Membership  Universitas Indonesia Library
cover
Bimo Ary Pujangga Putra
"Plastik sebagai bahan kemasan dan coating mengalami peningkatan global setiap tahun. Ini menimbulkan masalah serius bagi lingkungan karena sulitnya terdegradasi. Salah satu solusi untuk mengatasi masalah limbah plastik adalah penggunaan bioplastik. Untuk meningkatkan sifat mekanik dari bioplastik, biokomposit yang dibuat dengan penambahan aditif dan pengisi tertentu. Tujuan dari penelitian ini adalah untuk mengetahui pengaruh Butil Benzyl Phthalate plasticizer (BBP) dan Seng Oksida (ZnO) nanopartikel terhadap sifat mekanik dan termal biokomposit selulosa asetat butirat (CAB) / organoclay.

Nanopartikel ZnO disintesis dari prekursor ZnO komersial melalui metode reduksi ukuran sol-gel menggunakan asam sitrat. Seng sitrat dikalsinasi pada suhu 600oC. ZnO nanopartikel dengan ukuran rata-rata 44,4 nm diperoleh pada rasio seng nitrat 1:2 terhadap asam sitrat. Film biokomposit dibuat dengan menggunakan metode solution casting dengan aseton sebagai pelarut. Penambahan plasticizer BBP dan nanopartikel ZnO sebesar masing-masing 30% dan 10% membuat biokomposit memiliki nilai kekuatan tarik 2,22 MPa. Pergeseran nilai suhu transisi gelas (Tg) selulosa asetat butirat tidak dapat terlihat dikarenakan homogenitas biokomposit saat proses casting.


Plastics as packaging materials and coatings have increased globally every year. This poses a serious problem for the environment because of the difficulty to degrade. One solution to overcome the problem of plastic waste is the use of bioplastics. To improve the mechanical properties of bioplastics, biocomposites are fabricated with the addition of certain additives and fillers. The purpose of this study was to determine the effect of plasticizer Butyl Benzyl Phthalate (BBP) and Zinc Oxide (ZnO) nanoparticles to the mechanical and thermal properties of biocomposite cellulose acetate butyrate (CAB) / organoclay.

ZnO nanoparticles were synthesized from a commercial ZnO precursor through sol-gel  method to reduce the size using citric acid. Zinc citrate was calcined at a temperature of 600oC. ZnO nanoparticles with an average size of 44.4 nm were obtained at a mole ratio of zinc nitrate : citric acid was 1:2. Biocomposite films were made by solution casting method using acetone as the solvent. The addition of plasticizer BBP and ZnO nanoparticles by 30% and 10% respectively in the biocomposites produced a tensile strength of 2,223 MPa. Shifting value of the glass transition temperature (Tg) of cellulose acetate butyrate could not been observed due to the homogeneity of the biocomposite during the process of casting."

Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2017
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>