Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 82922 dokumen yang sesuai dengan query
cover
"ABSTRAK
Deposit laterit adalah salah satu jenis bijih nikel yang memiliki kandungan nikel
terbanyak di bumi. Di dalam lapisan laterit, saprolit memiliki kandungan nikel
yang lebih tinggi dibandingkan lapisan lainnya. Saprolite biasanya diproses secara
smelting (pirometalurgi) karena memiliki kandungan magnesium yang tinggi.
Penelitian ini bertujuan untuk mengetahui sejauh mana keefektifan proses
hidrometalurgi dengan lixiviant amonium bikarbonat terhadap perolehan nikel.
Bijih saprolit dikarakerisasi secara EDX dan AAS untuk mengetahui komposisi
awal bijih. Saprolit direduksi menggunakan batubara 33.33 % wt pada temperatur
1250 oC selama 120 menit. Hasil reduksi pemanggangan kemudian diuji dengan
XRD. Proses pelindihan agitasi pada bijih saprolit yang direduksi dan bijih yang
tidak direduksi dilakukan dengan menggunakan larutan amonium bikarbonat pada
variasi konsentrasi yaitu 1 M, 2 M, 3 M, 4 M. Kandungan nikel yang larut dalam
pregnant leach solutiont dihitung menggunakan Atomic Absorbance Spectroscopy
(AAS).
Hasil XRD saprolit menunjukkan terjadi transformasi fasa dari goethite dan Fe2O3
sebelum reduksi pemanggangan menjadi Fe3O4, NiO dan FeNi setelah reduksi
pemanggangan Hasil penelitian menunjukan % perolehan Ni semakin meningkat
dengan peningkatan konsentrasi amonium bikarbonat. Perolehan nikel tertinggi
yang diperoleh adalah 1.61 % pada konsentrasi pada konsentrasi 4 M amonium
bikarbonat.

Abstract
Laterite deposit is a kind of nickel ores that has the greatest of nickel reserves in the
world. In the lateritic layer, saprolite has higher nickel content more than other
layers. Saprolite is usually process with smelting method (pyrometallurgy)
because it has higher magnesium content.
The aim of this research is to know the effectiveness of hydrometallurgy process
using ammonium bicarbonate as lixiviant to nickel recovery from saprolite ore.
Saprolite was caracterized with Energy Dispersive X-Ray (EDX) and Atomic
Absorbance Spectroscopy (AAS) to determine it?s chemical composition. Floatsink
process was apllied to saprolite to separate material based on it?s weigth.
Saprolite was reduced at 1250 oC for 120 minutes utilized coal 33.33% wt as a
reductant, then it was tested with XRD. Agitation leaching process was applied to
reduced and unreduced saprolite utilized ammonium bicarbonate solution as lixiviant
at various concentration which was 1 M, 2 M, 3 M, 4 M. Nickel content that
dissolved in lixiviant was determined with Atomic Absorbance Spectroscopy
(AAS).
Result of XRD characterization shows phase transformation in saprolite from
goethite and Fe2O3 before reduction roasting to Fe3O4, NiO and FeNi after
reduction roasting. The result of research shows that % recovery of Ni is tend to
increase along with the increasing of ammonium bicarbonat concentration. The
higest nickel recovery in research is 1.61 % at 4 M ammonium bicarbonat
concentration.
"
Fakultas Teknik Universitas Indonesia, 2012
S43599
UI - Skripsi Open  Universitas Indonesia Library
cover
Achmad Taufiq Shidqi
"Tembaga merupakan salah satu mineral yang cukup penting dalam pertumbuhan ekonomi dan pembangunan bagi sebuah negara. Pada bijih jenis oksida yang berkisar 20% dari seluruh cadangan tembaga dunia, teknologi hidrometalurgi yang lebih ekonomis. Penggunaan alternatif lixiviant selain asam sulfat, misalnya ammonium bikarbonat, perlu diteliti lebih lanjut dengan parameter-parameter tertentu.
Penelitian ini menjelaskan mengenai pengaruh dari konsentrasi lixiviant dan waktu pelindian dengan menggunakan ammonium bikarbonat. Pada penelitian ini juga akan menganalisa mengenai pengaruh klasifikasi dengan menggunakan media air pada wadah bertingkat terhadap tren kecenderungan suatu unsur.
Hasil penelitian menunjukkan semakin tinggi konsentrasi maka akan semakin banyak pula kandungan PLS dan pengayaan yang dicapai. Sementara itu, Semakin lama waktu pelindian maka akan semakin banyak pula kandungan PLS dan pengayaan yang didapat. Kandungan PLS tertinggi dicapai pada konsentrasi 2.5 M dengan 4076 mg/L dan recovery sebesar 11.42 %. Pada waktu pelindian, kandungan tertinggi didapatkan pada waktu 120 menit dengan kandungan sebesar 2196 mg/L dan recovery sebesar 6.15%. Pengaruh klasifikasi dengan media air juga diteliti dalam percobaan ini dimana terjadi penurunan kadar pengotor dan kenaikan kadar tembaga.

Copper is the one of important mineral for economic growth and the country development. Copper oxide ore which only 20% of total reserves in the world, hydrometallurgical technology is more economical process. Aside from sulfuric acid, alternative lixivant such as ammonium bicarbonate need further investigation with specific parameters.
This study explain the effect of lixiviant concentration and leaching time using ammonium bicarbonate. This study also analys the effect of classification mineral using water with storay container toward the trend tendency of mineral.
The study shows the pregnant leach solution increased and more recovery gained with the increasing of lixiviant concentration. Also, the increasing of leaching time, pregnant leach solution and recovery increased. The highest PLS gained at 2.5 molar mass of ammonium bicarbonate with 4076 mg/L and 11.42% of recovery. The longest leaching time also gain 2196 mg/L and 6.15 % of recovery. The classification mineral show the decrease tendency of gangue and the increase tendency of copper.
"
Depok: Fakultas Teknik Universitas Indonesia, 2012
S42728
UI - Skripsi Open  Universitas Indonesia Library
cover
Suganta Handaru S.
"Deposit laterite adalah salah satu jenis bijih nikel yang memiliki cadangan mineral nikel terbanyak dan berlimpah di alam. Bijih limonite merupakan salah satu mineral dalam tiga daerah pada deposit laterite dapat menjadi sumber mineral nikel masa depan yang menarik untuk diproduksi menjadi logam nikel, walaupun kadar nikel didalamnya relatif rendah.
Pada penelitian ini dilakukan beberapa eksperimen meliputi karakterisasi awal bijih limonite, reduksi roasting dan agitasi leaching menggunakan amonium bikarbonat. Karakterisasi bijih limonite dilakukan menggunakan X-ray Diffraction (XRD) dan X-Ray Flourescence (XRF). Limonite direduksi menggunakan reduktor briket 20% wt pada temperatur 750°C selama 90 menit, hasilnya kemudian diuji menggunakan XRD. Dan yang terakhir proses agitasi leaching pada bijih limonite yang direduksi dan bijih yang tidak direduksi dengan menggunakan larutan amonium bikarbonat pada variasi konsentrasi yaitu 2 M, 1 M, 0.5 M, 0.2 M, 0.1 M, jumlah nikel yang larut kedalam larutan dianalisis menggunakan Atomic Absorbance Spectroscopy (AAS). Penelitian ini dilakukan untuk mengetahui transformasi fasa yang terjadi pada bijih limonite akibat reduksi roasting, recovery nikel pada bijih limonite oleh leaching amonium bikarbonat, dan pengaruh reduksi roasting dan variasi konsentrasi pelarut terhadap recovery nikel.
Hasil dari penelitian ini yaitu terjadi transormasi fasa dari geothite menjadi magnetite (Fe3O4) dan FeNi akibat reduksi roasting. Pada proses leaching amonium bikarbonat dengan konsentrasi 1 M recovery nikel yang diperoleh adalah sebesar 1.55 %, sehingga untuk mendapatkan nikel melalui proses ini tidak efektif. Recovery nikel yang didapat pada bijih nikel yang direduksi lebih tinggi 2.7 kali daripada bijih nikel yang tidak direduksi, dan diketahui juga bahwa dengan semakin tinggi konsentrasi pelarut maka recovery nikel akan semakin tinggi dan mencapai nilai optimal pada konsentrasi 1 M.

Laterite deposit is a kind of nickel ores that has the greatest of nickel reserves in the world. Limonite ores, which constitutes one of three zones of type lateritic deposits, is attractive future sources of nickel ores for the production of refined nickel, even though their nickel grades are low.
At this research, several experiments were conducted including characterization of limonite ore, reduction roasting and agitation leaching by ammonium bicarbonate. Characterization of limonite ore was done using X-ray Diffraction (XRD) and X-Ray Florescences (XRF). Limonite was reduced utilize 20 % wt briquette as a reductant at temperature up to 750oC for 90 minutes, and then the result is tested using XRD. And the last experiment is agitation leaching process of reduced limonite ore and unreduced ore utilize ammonium bicarbonate solution at various concentration which is 2 M, 1 M, 0.5 M, 0.2 M, 0.1 M, the number of nickel dissolution is measured using Atomic Absorbance Spectroscopy (AAS). This research is conducted to observe about the phase transformation of limonite ore as a result of reduction roasting, recovery nickel from limonite ore by ammonium bicarbonate leaching, and then the effects of reduction roasting and the effect of concentration of ammonium bicarbonate on the nickel recovery under atmospheric condition and room temperature.
The results of this research show the phase transformation from goethite transformed to magnetite (Fe3O4) and Fe-Ni as a result of reduction roasting. Nickel recovery by leaching using 1 M ammonium bicarbonate is 1.55 % wt, so the nickel extraction using this process is not effective. Nickel recovery obtained from reduced nickel ore is 2.7 times greater than nickel recovery from unreduced ore. Nickel recovery will increase if the concentration of ammonium bicarbonate increases, and achieve optimal value at 1 M."
2008
S41693
UI - Skripsi Open  Universitas Indonesia Library
cover
Sihotang, Juan Carlos
"Nikel merupakan logam penting yang banyak digunakan dalam paduan, misalnya baja tahan karat, paduan ruang angkasa, dan paduan khusus. Nikel ditambang dari dua jenis bijih: laterit dan sulfida. Laterit banyak ditemukan di daerah tropis seperti di Indonesia dan ditambang untuk memperoleh nikel dan kobalt. Pelindian bijih nikel laterit pada tekanan atmosfer saat ini banyak menarik perhatian karena biaya yang lebih rendah dibanding proses lainnya. Tujuan penelitian ini adalah untuk menentukan pengaruh waktu dan kecepatan agitasi pelindian atmosferik terhadap persentase perolehan nikel dari bijih laterit jenis saprolit. Bijih nikel saprolit dari Halmahera Timur digunakan dalam penelitian. Untuk mengetahui nilai perolehan nikel pada waktu dan kecepatan agitasi yang berbeda, pelindian teragitasi dilakukan selama 1, 3, dan 5 jam dengan kecepatan agitasi masing-masing 250 rpm, 500 rpm, dan 750 rpm. Selama penelitian, berat sampel yang telah dihaluskan (15 g), konsentrasi asam sulfat (5N (240.1 g/L)), volume asam sulfat (75 ml), dan suhu (100°C) dijaga konstan. Dapat dilihat bahwa dalam pelindian teragitasi, peningkatan waktu pelindian dari 1 jam hingga 5 hour memiliki pengaruh positif terhadap perolehan nikel. Peningkatan kecepatan agitasi dari 250 rpm hingga ke 750 rpm juga meningkatkan nilai perolehan nikel.

Nickel is important metal that is mostly used in alloys, for example, in stainless steels, aerospace alloys and specialty steels. Nickel is mined from two types of ores: laterites and sulfides. Laterites are found mostly in tropical regions and are mined for their nickel and cobalt in countries like Indonesia. Leaching lateritic nickel ores with sulphuric acid at atmospheric pressure (AL) has been recently receiving more attention due to lower cost compared to other processes. The purpose of this study is to determine the effect of duration and agitation speed of atmospheric leaching to the recovery percentage of nickel from saprolitic type laterit ore. Saprolitic nickel ores from Eastern Halmahera were used during experiments. In order to study the recovery values at different time periods and different agitation speeds, agitative leaching experiments were carried out for 1, 3, and 5 hours with agitation speed 250 rpm, 500 rpm, and 750 rpm, respectively. During the experiments, weight of ground ore sample (15 g), concentrations of sulfuric acid (5N (240.1 g/L)), volume of sulfuric acid (75 ml), and temperature (100°C) were kept constant. It was shown that in agitative leaching, increasing leaching time from 1 hour to 5 hour had a positive effect on metal extractions. Increasing agitation speed from 250 rpm to 750 rpm also increased the recovery values of nickel."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S63151
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rian Saputra
"Sources nickel laterite deposit of the world are mostly found in the tropic such as Indonesia. The initial composition of nickel saprolite ore is characterized by XRF. Saprolte ore was reduced use coal 15% wt at 1000°C for 60 minutes. The result of reduction is characterized by XRD. Effect of roasting reduction to recovery nickel also affect the result leaching use solvent sulphuric acid (H2SO4) for 240 minutes at 100°C with varying concentrations of 0.5 M, 1 M, and 2 M. The content of nickel dissolved in pregnant leach solution calculated using Atomic Absorbance Spectroscopy (AAS).
Result of XRD characterization shows phase transformation into Fe3O4, NiO, and FeNi after reduction roasting. Sulphuric Acid at concentration 1 Molar has the highest nickel recovery with 52.75% in reduced saprolite ore."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S63620
UI - Skripsi Membership  Universitas Indonesia Library
cover
Tambunan, Deddy
"Deposit laterite merupakan salah datu jenis bijih nikel yang memiliki cadangan mineral nikel terbanyak dan dapat dijumpai di alam. Indonesia adalah salah satu negara yang memproduksi bijih nikel yang cukup banyak di dunia. Bijih saprolite merupakan salah satu mineral nikel yang menarik untuk diproduksi menjadi logam nikel pada masa depan. Bahkan bijih saprolite memiliki kadar nikel yang banyak dalam mineral nikel laterite. Oleh karena itu, nikel saprolite disebut highgrade nickel.
Pada penelitian ini dilakukan beberapa percobaan meliputi karakteristik awal bijih saprolite, proses separasi dengan menggunakan fluida air atau float-sink process dan reduksi roasting. Karakterisasi awal bijih saprolite dilakukan menggunakan Energy Dispersive X-Ray (EDX). Saprolite dipisahkan dari pengotornya menggunakan float-sink process. Saprolite hasil separasi tersebut diuji dengan menggunakan EDX. Dan yang terakhir adalah saprolite direduksi menggunakan reduktor briket arang pada temperature 1000oC dengan variasi waktu 0 detik, 600 detik, 1200 detik dan 1800 detik. Saprolite yang direduksi diuji dengan X-Ray Diffraction (XRD). Penelitian ini dilakukan untuk mengetahui transformasi fasa yang terjadi pada bijih saprolite akibat variasi waktu reduksi roasting. Hasil penelitian ini yaitu terjadi transformasi fasa bijih saprolite menjadi ferronickel (FeNi) akibat reduksi roasting.

Laterite deposite is a kind if nickel ores that has the greatest of nickel reserves in the world. Indonesia is one of countries in the world that produces nickel ore in considerable amounts. Saprolite ore is attractive future sources of nickel ores for the production of refining nickel. Moreover, saprolite has good content of nickel in nickel laterite. So, it is named high-grade nickel.
At this research, several experiments were conducted including characterization of saprolite ore, separation method with using water or float-sink process dan roasting reduction. Characterization of saprolite ore was done using Energy Dispersive X-Ray (EDX). Saprolite ore was separated from gangue by using floatsink process. Characterization of saprolite from separation was done using EDX. And the last experiment is process of reduced saprolite ore utilize charcoal briquette as a reductant at temperature up to 1000oC for the variation of holding time which is 0 second, 600 second, 1200 second and 1800 second. Saprolite ore from roasting reduction was tested using X-Ray Diffraction (XRD). This research is conducted to observe about the phase transformation of saprolite ore as a result of the variation of holding time of roasting reduction process. The results of this research show the phase transformation of saprolite ore to be ferronickel (FeNi) as a result of roasting reduction.
"
Depok: Fakultas Teknik Universitas Indonesia, 2012
S42378
UI - Skripsi Open  Universitas Indonesia Library
cover
Doni Johansyah
"Bijih nikel laterit merupakan sumber bahan tambang yang berperan penting dalam produksi nikel dunia. Di Indonesia, bijih nikel laterit merupakan sumber daya yang melimpah. Bijih nikel laterit digolongkan menjadi dua jenis, yaitu saprolit yang berkadar nikel tinggi dan limonit yang berkadar nikel rendah. Tetapi hingga saat ini limonit belum dapat dimanfaatkan dengan baik, padahal jumlahnya jauh lebih besar daripada saprolit. Oleh karena itu, perlu dikembangkan metode yang efisien dan ekonomis agar limonit dapat dimanfaatkan.
Penelitian ini bertujuan untuk mengetahui efek dari reduksi pemanggangan dan pengaruh waktu pelindian amonium bikarbonat pada bijih limonit. Metode yang dilakukan dalam penelitian ini meliputi reduksi pemanggangan dan pelindian amonium bikarbonat yang dikarakterisasi menggunakan Energy Dispersive X-ray (EDX), X-ray Diffraction (XRD), dan Atomic Absorption Spectroscopy (AAS) untuk mengetahui kandungan unsur dan senyawa yang terdapat dalam sampel.
Dari penelitian yang dilakukan diketahui bahwa terjadi perubahan senyawa dari (FeO)OH menjadi Fe2O3, Fe3O4, dan FeNi pada sampel setelah proses reduksi pemanggangan serta terjadi peningkatan persen perolehan nikel hingga mencapai 1,88% akibat penambahan waktu pelindian selama 120 menit.

One form of innovation to reduce the time spent on the production of ships and ship production costs is make a connection to the shape steel plates in the hull without bending or forming process on the curvature the hull to get a streamline hull shape. Technically innovation method of make the ship's hull with a flat plate have an influence in change the stability and strength of the transverse vessels. Thus it is necessary for the calculation to determine how much influence these changes to the safety of the ship.
In this research the stability of ship use Maxsurf Software approach. For the calculation of Ship stability use standard IMO. For the calculation of the transverse strength of ships use standard Bureau Classification Indonesia (BKI) and modeling approaches transverse strength analysis use CATIA Software.
From the results is obtained analysis of ship stability is good and has fulfilled criteria IMO. Review from the modeling of the transverse strength at least ship midship 0.4L. On the first condition in midship has maximum working stress on the base bulkhead is 1.59 x 1011 N/m2. On the second condition in midship bulkhead have arch as high as 384 mm and maximum working stress is 1.0757 x 1011 N/m2. On the third condition in midship bulkhead has arch as high as 150 mm and maximum working stress is 1.08 x 1011 N/m2. Safety factor in the first condition is 1.25, second condition is 1.85, and third condition is 1.85.
"
Depok: Fakultas Teknik Universitas Indonesia, 2012
S1949
UI - Skripsi Open  Universitas Indonesia Library
cover
Gana Damar Kusuma
"Sejak lama, mayoritas logam nikel diproduksi melalui bijih sulfide. Namun, Namun, dengan semakin menurunnya cadangan nikel sulfida dan di sisi lain permintaan terhadap logam nikel semakin tinggi, maka pemurnian nikel dari bijih laterit semakin menjanjikan karena berlimpahnya cadangan bijih laterit dan biaya penambangannya relatif lebih rendah. Oleh sebab itu, bijih laterit berpotensi menjadi sumber bahan baku utama untuk memperoleh logam nikel di masa yang akan mendatang.
Penelitian ini menggunakan bijih laterite kadar rendah atau limonite, dengan tujuan untuk mengetahui fasa yang terdapat pada bijih pada keadaan awal dan pada keadaan setelah proses reduksi roasting dengan suhu 600°C dan komposisi serbuk batu bara 20% wt selama 30 menit dengan menggunakan XRD. Selain itu, pengaruh reduksi roasting terhadap proses recovery logam nikel juga dilakukan dengan melakukan leaching menggunakan pelarut asam sulfat (H2SO4) selama 60 menit dan suhu kamar (±25°C) dengan konsentrasi bervariasi dari 0.1 sampai 0.4 M.
Hasil penelitian ini menunjukkan bahwa proses reduksi roasting dan peningkatan konsentrasi H2SO4 pada leaching mempunyai pengaruh positif terhadap % recovery nikel. Pada bijih limonit yang tidak direduksi, leaching dengan konsentrasi 0.4 M mempunyai %recovery 10.13%. Sedangkan pada bijih yang tereduksi, leaching dengan konsentrasi 0.4 M menghasilkan %recovery sebesar 12.71%.

The majority of nickel metals are produced through sulfide ore. However, with the decreasing of nickel sulfide ore deposite and on the other hand, the demand of nickel metal is getting higher, then the extraction process using laterite ore is more promising since the abundance of the ore and the low cost of its mining process. Hence, laterite ore will potentially be the main source to obtain nickel in the near future.
This experiment is using low grade laterite ore, namely limonite, in purpose to recognize the phases which are exist in the raw ore and in the roasted ore at temperature 600°C and pulverized coal composition 20%wt in 30 minutes using XRD. Moreover, the effect of reduction roasting on recovery of nickel is done with sulphuric acid (H2SO4) leaching in 60 minutes and room temperature (±25°C) with various concentration from 0.1 to 0.4 M.
The result shows that the reduction roasting and the increasing of the concentration of H2SO4 in leaching have the positive impact on %recovery nickel. In unreduced limonite ore, leaching using 0.4 M concentration has 10.13% of %recovery, whereas in reduced ore, leaching using 0.4 M concentration has 12.71% of %recovery.
"
Depok: Fakultas Teknik Universitas Indonesia, 2012
S42608
UI - Skripsi Open  Universitas Indonesia Library
cover
Mutiarto Bangalino
"Pengembangan penelitian proses pirometalurgi bijih nikel saprolit sangat dibutuhkan untuk meningkatkan nilai efisisen dan keefektifan dalam merecovery unsur nikel. Penelitian ini akan membahas pengaruh penambahan reduktor subbituminous dan briket dengan kadar 10%, 13%, 15%, 20% pada temperatur 1250_C pada produk reaksi karbotermik yang ditahan selama 120 menit, yang dilakukan di dalam carbolite furnace yang selanjutnya dilakukan pengujian dengan menggunakan XRD untuk mengidentifikasi senyawa, SEM untuk mengamati struktur mikro dan XRF untuk melihat kadar unsur secara kuantiatif.
Dari hasil pengujian yang diperoleh menunjukan bahwa pembentukan senyawa FeNi dan nilai recovery Ni yang maksimum terjadi pada penambahan reduktor sub-bituminous kadar 20%. Pada penambahan reduktor briket kokas pembentukan senyawa FeNi dan nilai recovery Ni yang maksimum terjadi pada penambahan kadar 15%, sedangkan pada penambahan reduktor grafit, pembentukan senyawa FeNi dan recovery Ni yang maksimum terjadi pada penambahan kadar 15%. Disamping itu penambahan reduktor sub-bituminous, briket kokas, dan grafit tidak menunjukkan perbedaan yang signifikan terhadap bentuk morfologi produk reduksi.

Research and development of pyrometullurgy is very important to increase the efficiency and effectivity of nickel recovery. This research investigate the effect of 10%, 13%, 15%, 20% briquette cokes and sub-bituminous reductor addition on the carbothermic reaction product of saprolite nickel ore on temperature 1250 _C which will be holding for 120 minutes, in the furnace. The samples was characterized by XRD, XRF, and SEM.
The results show that Ni recovery and formation of FeNi maximum on 20% sub-bituminous reductor addition, on the briquette cokes reductor addition, Ni recovery and formation FeNi maximum on 15% briquette cokes addition. While on graphite reductor, Ni recovery and formation of FeNi maximum on 13% graphite reductor addition. Beside that briquette cokes, sub-bituminous and graphite reductor addition does not show significant difference on morphology shape of reduction products.
"
Depok: Fakultas Teknik Universitas Indonesia, 2009
S51523
UI - Skripsi Open  Universitas Indonesia Library
cover
Pranata Yassi Tanzila
"Studi reduksi karbotermik pada bijih nikel saprolit ini bertujuan untuk mengetahui pengaruh temperatur dalam memperoleh kadar nikel yang optimal. Pengujian dilakukan pada empat temperatur yang berbeda, yaitu: 700, 800, 900, dan 1000°C selama 60 menit. Pada proses pembakaran, perbandingan bijih nikel saprolit dan batubara, masing-masing adalah 20 dan 80 gram. Selama proses pembakaran pada temperatur 700-1000°C, mulai terlihat metalisasi besi pada temperatur 900°C, sedangkan metalisasi nikel dan kobalt yang mulai terlihat pada temperatur yang lebih rendah. Metalisasi nikel, kobalt, dan besi dilihat secara kualitatif melalui karakterisasi Difraksi Sinar-X (XRD) dan untuk mengetahui masing-masing kadar unsur yang diperoleh dari proses reduksi karbotermik dengan menggunakan Floresensi Sinar-X (XRF). Berdasarkan studi yang dilakukan, diperoleh kadar nikel yang optimal 8,23% pada temperatur 800°C selama 60 menit.

The study of carbothermic reduction on saprolitic nickel ore aims to determine the effect of temperature in obtaining optimal levels of nickel recovery. The experiments carried out at four different temperatures, they are 700, 800, 900, and 1000oC for 60 minutes. In the reduction process, the ratio of saprolite ore and coal are 20 and 80 gram, respectively. During the reduction process at temperatures between 700-1000°C, began to look the metallization of iron at a temperature of 900°C, while the metallization of nickel and cobalt are beginning to look at lower temperature. The metallization of nickel, cobalt, and iron quantitively seen through the characterization of X-ray Diffraction (XRD) and to determine the concentration of each element obtained from the carbothermic reduction process using X-ray Flourescent (XRF). Based on studies conducted, the optimal nickel grade of 8.23% is at a temperature of 800°C for 60 minutes."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S63083
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>