Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 98148 dokumen yang sesuai dengan query
cover
Desy Qoiriyani
"Semakin meningkatnya konsumsi listrik dunia menuntut para peneliti untuk menemukan sumber energi baru. Penelitian Microbial Fuel Cell (MFC) sebagai salah satu sumber energi alternatif dilaksanakan untuk mengetahui kapasitas dan efisiensi produksi energi listrik yang dihasilkan. Penelitian ini menggunakan reaktor jenis single-chamber tanpa membran penukar ion dengan limbah cair pabrik tempe sebagai substrat. Elektroda yang digunakan sebagai mediator elektron adalah elektroda grafit. Variasi perlakuan awal anoda dilakukan dengan menumbuhkan biofilm pada anoda selama 3 minggu sebelum eksperimen (anoda prekolonisasi) dan membandingkan dengan sistem menggunakan anoda yang tidak ditumbuhi biofilm (anoda bersih). Variasi penambahan substrat berupa kulit ari kedelai juga dilakukan untuk mendapatkan hasil yang maksimum. Hasil dari penelitian ini menunjukkan sistem dengan anoda bersih tanpa penambahan substrat kulit ari kedelai menghasilkan produksi listrik terbesar dengan densitas daya sebesar 1009,34 mW/m2. Penelitian ini juga menggunakan limbah cair pabrik tempe dan dihasilkan densitas daya sebesar 44,62 x 10-2 mW/m2.

Increasing of world electricity consumption in the world make researchers try to find new energy source. Researching Microbial Fuel Cell as a new energy source did for knowing electricity production capacity and efficiency. Single chamber reactor without ion exchange membrane with industry tempeh wastewater used in this experiment. We used graphite electrode as an electron mediator. Make biofilm grow in the anode for 3 weeks (precolonization anode) did for system variation and then we compared with clean anode system. Skin of soy bean used as a substrate in the system for second variation. Optimum electricity production obtained from clean anode without addition of soy bean skin system. Power density obtain was 1009,34 mW/m2 when using wastewater model and 44,62 x 10-2 mW/m2 when using industry tempeh wastewater."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S44239
UI - Skripsi Membership  Universitas Indonesia Library
cover
Avia Rizki Noordiany
"[Parameter COD dan TDS merupakan dua parameter yang nilainya paling tinggi pada limbah susu yaitu dengan kisaran 1.000-8.000 mg/L untuk COD dan 1.000-4.000 mg/L untuk TDS. Penelitian ini dilakukan untuk menurunkan kedua nilai parameter tersebut menggunakan bioreaktor Microbial Fuel Cell (MFC) yaitu merupakan sebuah teknologi alternatif pengolahan limbah yang dapat mendegradasi kandungan organik limbah serta menghasilkan energi listrik secara langsung tanpa membutuhkan konversi dan untuk melihat potensi limbah susu secara teoritis dalam menghasilkan energi listrik Penelitian dilakukan selama 2 bulan dengan membuat reaktor. MFC skala laboratorium dengan jenis single chamber tanpa membran berukuran 16/L dengan dimensi 40/20/20 cm Terdapat penambahan bakteri Escherichia coli untuk meningkatkan degradasi kandungan organik limbah. Penelitian yang dilakukan secara batch ini menunjukkan efisiensi penurunan COD sebesar 51 pada waktu tinggal 13 hari sedangkan TDS mengalami peningkatan karena adanya penambahan larutan elektrolit. Dengan konsentrasi COD influen sebesar 3.853 mg/L penurunan rata rata COD dari total yang tersisihkan adalah 7.7 setiap harinya Limbah susu ini memiliki potensi untuk dijadikan substrat dalam reaktor MFC karena secara teoritis dapat menghasilkan arus maksimum sebesar 340 mA dengan efisiensi Coulomb sebesar 13 Hasil ini lebih besar dibandingkan dengan penelitian lain yang menggunakan limbah domestik sebagai substrat.

COD and TDS are two parameters that have the highest value in dairy wastewater with a COD ranging between 1.000 and 8.000 mg/L and a TDS ranging between 1.000 and 4.000 mg/L. The aim of this study is to reduce the value of these parameters by using a Microbial Fuel Cell (MFC) bioreactor an alternative wastewater treatment technology that can degrade the organic content of the wastewater and produce electrical energy directly without the need of conversion and to see theoretically the dairy wastewater potential in power generation Research is done for 2 months by creating a laboratory scale MFC reactor with single chamber type without a membrane and has reactor volume of 16/L with dimensions of 40/20/20 cm. There is an addition of Escherichia coli bacteria to increase the degradation of the organic content of the wastewater Research which carried out in batch shows COD removal efficiency of 51 at the HRT of 13 days while TDS has increased due to the addition of an electrolyte solution As influent COD concentration is 3.853 mg/L the average decrease of the total excluded COD was 7.7 per day Therefore dairy wastewater has the potential to be used as a substrate in MFC reactor because theoretically it can produce a maximum current of 340 mA with Coulomb efficiency of 13. These result is greater than other research that use domestic wastewater as a substrate., COD and TDS are two parameters that have the highest value in dairy wastewater with a COD ranging between 1 000 and 8 000 mg L and a TDS ranging between 1 000 and 4 000 mg L The aim of this study is to reduce the value of these parameters by using a Microbial Fuel Cell MFC bioreactor an alternative wastewater treatment technology that can degrade the organic content of the wastewater and produce electrical energy directly without the need of conversion and to see theoretically the dairy wastewater potential in power generation Research is done for 2 months by creating a laboratory scale MFC reactor with single chamber type without a membrane and has reactor volume of 16 L with dimensions of 40 20 20 cm There is an addition of Escherichia coli bacteria to increase the degradation of the organic content of the wastewater Research which carried out in batch shows COD removal efficiency of 51 at the HRT of 13 days while TDS has increased due to the addition of an electrolyte solution As influent COD concentration is 3 853 mg L the average decrease of the total excluded COD was 7 7 per day Therefore dairy wastewater has the potential to be used as a substrate in MFC reactor because theoretically it can produce a maximum current of 340 mA with Coulomb efficiency of 13 These result is greater than other research that use domestic wastewater as a substrate ]"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S61384
UI - Skripsi Membership  Universitas Indonesia Library
cover
Guruh Mehra Mulyana
"Microbial Fuel Cell (MFC) merupakan salah satu teknologi yang dikembangkan untuk mendapatkan sumber energi baru terbarukan. Namun teknologi ini tergolong mahal, sehingga penelitian pun banyak diarahkan untuk menjadikan teknologi ini lebih efisien, ekonomis dan berkelanjutan. MFC yang memanfaatkan limbah industri tempe sebagai substrat, merupakan salah satu alternatif yang dapat dikembangkan. Mikroorganisme pada limbah industri tempe yang berpotensi mencemari lingkungan di sekitar dapat dimanfaatkan aktivitasnya untuk menghasilkan suatu energi listrik. Pada penelitian sebelumnya telah dilakukan uji coba penggunaan reaktor dual dengan menggunakan membran dan reaktor tunggal tanpa membran (single chamber/membranless). Namun, hasil yang diberikan masih perlu dilakukan peningkatan kinerja.. Oleh sebab itu, penelitian ini difokuskan pada MFC dengan penggunaan reaktor tubular chamber/membranless dengan variasi penambahan bakteri konsorsium, substrat yang disirkulasikan serta jumlah reaktor. Hasil penelitian didapatkan listrik keluaran terbesar dari percobaan menggunakan multireaktor yang dikonfigurasikan secara paralel dengan substrat yang disirkulasikan, tegangan maksimum 301,9 mV dan 5,39 mW/m2 untuk power density. Hasil coloumbic efficiency terttinggi diperoleh dari percobaan dengan variasi penambahan sejumlah konsorsium menggunakan multireaktor. Riset lebih lanjut perlu dilakukan guna mendapatkan energi listrik yang maksimum dan efisien, supaya industri yang bersangkutan dapat mereduksi biaya operasi dengan menggunakan listrik yang dihasilkan oleh limbahnya, sehingga tujuan menjadikan MFC sebagai teknologi yang ekonomis, berkelanjutan dan ramah lingkungan dapat tercapai.

Microbial fuel cell (MFC) is a technology developed to obtain new sources of renewable energy. But this technology is quite expensive, so teh research was directed to make this technology more efficient, economical and sustainable. MFC that utilize industrial waste of tempe as a substrate, is one alternative that can be developed. Activity of microorganism in industrial waste of tempe potentially contaminate the surrounding environment can be used to produce an electrical energy. In the previous study have been done testing performance of dual chamber MFC with membrane and single chamber MFC without membrane (single chamber/membranless). However, given the result still need improve the performance. Therefore, this study focused on using a tubular reactor MFC/membranless with variations are the addition of consortium, circulating substrate and the number of reactor. The result showed the biggest electricity output obtain from the experiment using multireaktor configured in parallel with the substrate is circulated, the maximum voltage 301.9 mV and 5.39 mW/ m2 of power density. The highest coloumbic efficiency results obtained from experiments with variations of the addition of a number of consortia using multireactor. Further research needs to be done in order to obtain maximum electrical energy and efficient, so that the industry concerned can reduce operating costs by using electricity generated by waste, so the aim of making the MFC as a technology that is economical, sustainable and environmentally friendly can be achieved."
Depok: Fakultas Teknik Universitas Indonesia, 2015
S59293
UI - Skripsi Membership  Universitas Indonesia Library
cover
Hasna Aprilia
"Usaha bengkel yang ditangani oleh ahli mekanik atau montir ditujukan agar pemilik kendaraan bermotor dapat melakukan perawatan dan perbaikan terhadap kendaraan mereka. Selain membuka lapangan pekerjaan, usaha bengkel juga berpotensi untuk mencemari lingkungan karena menghasilkan limbah oli. Salah satu cara pengolahan limbah oli adalah dengan sistem desalinasi air laut yang memanfaatkan exoelectrogenic bacteria sebagai agen pendegradasi senyawa-senyawa organik pada limbah oli. Microbial Desalination Cell (MDC) adalah pengembangan dari Microbial Fuel Cell (MFC), merupakan metode yang dapat menghilangkan kandungan garam dalam air laut menggunakan listrik yang dihasilkan oleh bakteri dari air limbah. Sistem MDC terus mengalami perkembangan, salah satunya dengan memodifikasi reaktor menjadi Stacked Microbial Desalination Cell (SMDC) yang berfungsi untuk meningkatkan efisiensi kinerja dari MDC. Pada penelitian ini, menggunakan konfigurasi reaktor 2-SMDC dengan batang grafit sebagai anoda dan CFC yang dilapisi karbon aktif sebagai katoda serta katolit kalium permanganat. Variabel bebas yang digunakan dalam penelitian ini adalah variasi massa karbon aktif sebesar 0, 2, dan 4 g. Parameter uji dalam penelitian ini terdiri dari COD, produktivitas listrik, dan pH. Hasil yang diperoleh dalam penelitian ini menunjukkan variasi massa karbon aktif paling optimum yaitu 4 g dengan penurunan COD sebesar 57,808% serta menghasilkan produktivitas listrik sebesar 0,000561 W/m3.

Garage shop has potential to pollute the environment because it produces oil waste. One way to treat oil waste is a seawater desalination system that uses exoelectorgenic bacteria as an agent for the degradation of organic compounds contained in oil waste. Microbial Desalination Cell (MDC) is a development of Microbial Fuel Cell (MFC), a method that can eliminate salt content in seawater using electricity generated by bacteria from wastewater. MDC system continues to experience development, one of which is to modify the reactor into a Stacked Microbial Desalination Cell (SMDC) which serves to improve efficiency of the performance of MDC. In this research, using a 2-SMDC reactor configuration with graphite rods as anode, CFC coated with activated carbon as a cathode and potassium permanganate as catholyte. Independent variables used in this research were active carbon mass variations of 0, 2, and 4 g. Parameters that will be obtained are COD, electrical productivity, and pH. The results obtained in this study indicate that the optimum mass variation of activated carbon is 4 g with a COD reduction of 57,808% and produces electrical productivity of 0,000561 W/m3."
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Thika Herlani
"Meningkatnya kebutuhan energi listrik telah memicu dilakukannya riset ke arah teknologi inovatif berkelanjutan dan ramah lingkungan. Microbial Fuel Cell (MFC) merupakan salah satu alternatif yang dapat dikembangkan untuk memproduksi listrik. Penelitian difokuskan pada peningkatan kinerja MFC dengan limbah model dan limbah industri tempe menggunakan variasi konfigurasi rangkaian reaktor tunggal MFC secara seri, paralel dan campuran. Hasil dari penelitian adalah power density dari rangkaian seri (0,005 mW/m2), paralel (0,13 mW/m2) dan campuran (0,006 mW/m2). Rangkaian dengan power density terbaik, paralel, diaplikasikan pada limbah industri tempe dan menghasilkan power density sebesar 0,23 mW/m2. Untuk mengetahui efisiensi dari rangkaian digunakan power transfer sebagai pembanding. Power transfer yang dihasilkan oleh rangkaian seri, paralel dan campuran berturut-turut adalah 51,6%; 50,6% dan 52,6%.

The increasing demand of electrical energy has led to researches toward innovative sustainable and environment-friendly technology. Microbial fuel cells (MFC) is one of the alternatives can be developed for producing electricity. The focus was on improving performance MFC with tempe model and tempe industrial wastes using variations of configuration single reactor MFC for series, parallel and series-parallel connection. The result is the density of the series (0,005 mW/m2), parallel (0,13mW/m2 ) and series-parallel configuration (0,006mW/m2). Configuration with the best power density, parallel, apply to produce power density from tempe industrial wastes, 0,23 mW/m2. Efficiency of configuration known by its power transfer. Power transfer that produced by series, parallel and series-parallel are 51.6 %; 50,6 % and 52,6 %.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
S52777
UI - Skripsi Membership  Universitas Indonesia Library
cover
Huriya
"Teknologi membran saat ini sudah banyak diaplikasikan untuk mengolah limbah berbagai industri, salah satunya dapat industri tahu. Namun di Indonesia, pengolahan limbah industri tahu masih menggunakan metode konvensional dan belum memenuhi baku mutu pemerintah, sehingga dibutuhkan metode pengolahan yag lebih efektif. Penelitian ini bertujuan untuk melakukan preparasi serta menguji kinerja membran polisulfon dengan proses filtrasi untuk pengolahan limbah cair industri tahu. Penelitian ini diawali oleh preparasi membran polisulfon (PSf) dengan pelarut n-metil-2-pirolidon (NMP) dan aditif polivinilpirolidon (PVP) dengan metode inversi fasa dan teknik imersi presipitasi, dengan variasi massa PVP sebanyak 0,15 gram; 0,25 gram; dan 0,35 gram. Membran yang telah dipreparasi kemudian dikarakterisasi menggunakan SEM, FTIR, serta sudut kontak. Limbah cair tahu sebagai umpan filtrasi telah melalui proses pre-treatment dengan metode koagulasi-flokulasi. Kemudian limbah umpan tersebut difiltrasi menggunakan membran PSf/NMP/PVP dengan variasi umpan 4, 5, 6, dan 7 bar. Penambahan konsentrasi PVP meningkatkan porositas dan hidrofilisitas, namun penambahan PVP yang berlebihan akan meningkatkan viskositas membran sehingga membuat membran menjadi lebih padat. Hal ini yang menyebabkan fluks air dan fluks permeat mengalami kenaikan pada membran PSf/NMP/PVP0,15 dan PSf/NMP/PVP0,25 namun namun menurun pada PSf/NMP/PVP0,35. Rejeksi COD dan TDS yang dihasilkan pada penelitian berkisar antara 8,3% hingga 60,53% dan 4,77% hingga 28,57%; sedangkan rejeksi TSS dan kekeruhan yang dihasilkan berkisar antara 16,67% hingga 75% dan 8,3% hingga 75%; dan pH berkisar antara 7,28 hingga 7,58.
.....Membrane technology nowadays is applied for wastewater treatment in multiple industries, one of them is the tofu industry. However in Indonesia, tofu industrial wastewater treatment still uses the conventional method that has yet to meet the government’s quality standards, so a more effective treatment method is needed. This research aimed to prepare and examine the performance of polysulfone (PSf) membrane using n-methyl-2-pyrrolidone (NMP) solvent and polyvinylpyrrolidone (PVP) additive according to phase inversion method by immersion precipitation technique, with PVP mass variation of 0,15; 0,25; and 0,35 grams. Membrane that has been prepared is then characterized by undergoing several tests of SEM, FT-IR, and contact angle. First, tofu wastewater as feed has been through the pre-treatment process using coagulation-flocculation method. The feed is then filtrated using prepared PSf/NMP/PVP membranes with pressure variation of 4, 5, 6, and 7 bars. The addition of PVP concentrations increases porosity and hydrophilicity, but the excessive addition of PVP will increase membrane viscosity thereby making the membrane denser. This is what causes the water flux and permeate flux to increase in PSf/NMP/PVP0,15 and PSf/NMP/PVP0,25 membranes but decrease in PSf/NMP/PVP0,35 membrane. The COD and TDS rejection percentages resulted in this research ranged from 8,3% up to 60,53% and 4,77% up to 28,57%; the TSS dan turbidity rejection percentages ranged from 16,67% up to 75% and 8,3% up to 75%, meanwhile the pH varies from 7,28 to 7,58."
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Novan Akhiriyanto
"ABSTRAK
Kepulauan Selayar sebagai salah satu Kabupaten penghasil kelapa beserta kopra terbesar di Provinsi Sulawesi Selatan memiliki potensi energi dari limbah industri kopra yang cukup besar berupa tempurung dan sabut kelapa. PLTD berbahan bakar BBM merupakan satu-satunya pemasok energi listrik di Selayar, sehingga biaya pembangkitan listrik relatif lebih mahal dibanding dengan menggunakan bahan bakar fosil lainnya dan juga menimbulkan permasalahan emisi gas buang. Pemanfaatan limbah industri kopra sebagai bahan bakar pembangkitan listrik merupakan alternatif yang ditawarkan dalam studi ini. Pembangkit listrik tenaga gasifikasi biomassa PLTGBm dengan reaktor downdraft gasifier menghasilkan gas mudah terbakar yang digunakan sebagai bahan bakar generator mesin gas untuk menghasilkan energi listrik diterapkan dengan 2 dua skenario pengoperasian, yaitu untuk membantu memikul beban siang 16 jam operasi dengan faktor kapasitas CF sebesar 66,67 dan beban malam 8 jam operasi dengan CF sebesar 33,33 . Potensi daya listrik dengan CF 66,67 sebesar 730 kW dari PLTGBm tempurung mempunyai kontribusi pembangkitan listrik mencapai 12,47 dalam memikul beban listrik pada April 2017 dengan potensi penghematan biaya bahan bakar menggantikan biaya pengadaan BBM untuk pembangkitan listrik sebesar Rp. 29.101.125,80 dan 1.470 kW dari PLTGBm sabut mempunyai kontribusi mencapai 25,10 dengan potensi penghematan sebesar Rp. 58.618.416,79. Sedangkan potensi daya listrik dengan CF 33,33 sebesar 1.470 kW dari PLTGBm tempurung mempunyai kontribusi mencapai 14,14 dengan potensi penghematan sebesar Rp. 19.462.180,74 dan 2.950 kW dari PLTGBm sabut mempunyai kontribusi mencapai 28,38 dengan potensi penghematan sebesar Rp. 39.063.083,22. Analisis kelayakan ekonomi juga diperhitungkan dalam studi, ditemukan bahwa PLTGBm tempurung 730 kW dan PLTGBm 1.470 kW layak untuk dikembangkan untuk memikul beban siang sedangkan PLTGBm tempurung 1.470 kW dan PLTGBm 2.950 kW tidak layak secara keekonomian.54

ABSTRACT
Selayar Islands as one of the largest copra producing district in South Sulawesi province has large enough the potential of energy from copra industry waste in the form fo coconut shell and husk. Diesel generator is the primary supplier of electricity in Selayar, so that the cost of power generation is relatively more expensive than using other fossil fuels and also raises the problem of emissions. Utilization of copra industry waste as fuel for electricity generation is an alternative offered in this study. Biomass gasification power plant PLTGBm with reactor downdraft gasifier produce flammable gas used as fuel gas engine generator to generate electrical energy is applied to the 2 two scenarios of operation, which is to help carry the day load 16 operation hours by a capacity factor CF of 66.67 and night load 8 operation hours with CF of 33.33 . Electric power potential with CF 66.67 amounting to 730 kW of PLTGBm shell contributes power generation to 12.47 in the burden of electricity load in April 2017 with the potential fuel cost savings offset the cost of procurement of oil fuel for electricity generation amounted to Rp. 29.101.125,80 and 1,470 kW from PLTGBm husk have contribution to 25,10 with the potential of savings amount Rp. 58.618.416,79. While the potential of electric power with CF 33.33 of 1470 kW from PLTGBm shell has a contribution to 14.14 with a potential savings of Rp. 19.462.180,74 and 2,950 kW from PLTGBm husk have contributed to 28.38 with a potential savings of Rp. 39.063.083,22. Economic feasibility analysis is also taken into account in the study, it was found that the shell PLTGBm 730 kW and 1,470 kW PLTGBm are feasible to be developed to carry the load during PLTGBm shell while 1,470 kW and 2,950 kW PLTGBm unfeasible economically.55"
2017
T47936
UI - Tesis Membership  Universitas Indonesia Library
cover
Denny Prahtama
"ABSTRAK
Permasalahan sampah dapat dikurangi dengan menggunakan sistem digestasi anaerobik. Sampah makanan mengandung banyak kandungan organik serta limbah ikan yang kaya akan lemak yang dapat berfungsi sebagai substrat. Tujuan dari penelitian ini untuk mengetahui hubungan rasio C/N dan pH dengan komposisi gas, hubungan logam ringan dan LCFAs sebagai faktor penghambat dengan komposisi gas, dan mengetahui fluktuasi pembebanan COD. Penelitian ini dilakukan dengan sistem batch menggunakan dua digester (A perbandingan sampah makanan dan limbah ikan 70:30 dan B 50:50) dengan variabel rasio C/N, komposisi gas, pH, logam ringan, LCFAs, dan COD. Hasil yang didapat ialah rasio C/N berkisar 8,6-11,1; pH berkisar 3,1-5,7; komposisi gas menunjukkan tidak ada metana dan yang mendominasi adalah karbon dioksida berkisar 23-64% dan 11-66% pada digester A dan B. Terdapat kandungan logam ringan, pada digester A dan B masing-masing Mg 82,01 mg/L dan 86,16 mg/L; Ca 647,98 mg/L dan 1231,62 mg/L; K 777,88 mg/L dan 734,50 mg/L; Na 1261,7 mg/L dan 1191,98 mg/L. Terdapat kandungan LCFAs, pada digester A dan B masing-masing asam oleat 29,23% dan 38,86%; asam palmitat 25,09% dan 40,04%; asam miristat 0,75% dan 1,39%. Konsentrasi COD untuk digester A dan B berkisar 28.339 – 47.373 mg/L dan 23.616 – 49.866 mg/L. Hasil menunjukkan proses masih berada pada tahap asidogenesis. Adanya kandungan logam ringan di atas ambang batas optimum dan kandungan LCFAs di dalam substrat menjadi penghambat bagi terbentuknya metana.

ABSTRACT
Waste problem can be reduced by using anaerobic digestion system. Food waste contains high organic and fish waste that is rich in fatty and can be useful as substrate. The purpose of this study was to investigate relationship of C/N ratio and pH with gas composition, relationship of light metals and LCFAs as inhibitor variables with gas composition, and to investigate fluctuation of COD loading. This study was conducted with a batch system using two digesters (with A with substrate comparison food waste and fish waste 70:30 and B 50:50) with variables C/N ratio, gas composition, pH, light metals, LCFAs, and COD. The results are C/N ratio ranged from 8.6-11.1; pH ranged from 3.1-5.7; gas composition showed no methane and dominated by carbon dioxide ranging from 23-64% and 11-66% for digester A and B. There are light metals content, the digester A and B contained Mg 82.01 mg/L and 86.16 mg/L; Ca 647.98 mg/L and 1231.62 mg/L; K 777.88 mg/L and 734.50 mg/L; Na 1261.7 mg/L and 1191.98 mg/L. There are LCFAs content, the digester A and B contained oleic acid 29.23% and 38.86%; palmitic acid 25.09% and 40.04%; miristic acid 0.75% and 1.39%. Concentration of COD for digester A and B ranged from 28,339 – 47,373 mg/L and 23,616 – 49,866 mg/L. The results indicate the process is still at the acidogenesis stage. There are high concentration of light metals and LCFAs in substrate become inhibitor to the formation methane.
"
Fakultas Teknik Universitas Indonesia, 2014
S57633
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ahmad Maksum
"Secara umum penelitian ini bertujuan untuk mengeksplorasi kemungkinan penggunaan limbah biomassa dalam proses reduction roasting bijih besi nikel laterite Indonesia. Adapun motif di balik penelitian ini adalah untuk meningkatkan nilai tambah dari bijih besi kadar rendah dan mendapatkan bio-reduktor baru yang akan menjadi alternatif pengganti batu bara di masa depan. Dalam penelitian ini diteliti tiga limbah biomassa sebagai agen pereduksi bijih besi nikel laterite dari Sorowako, yaitu: ampas tebu dari kabupaten Cirebon, cangkang sawit dari Palangkaraya - Kalimantan Tengah, dan sekam padi dari Kerawang - Jawa Barat. Adapun metode yang digunakan adalah reduction roasting dengan variasi parameter temperatur, rasio massa, dan waktu reduksi. Selanjutnya dilakukan analisis berdasarkan pola difraksi hasil X-Ray Diffraction (XRD), X-Ray Fluorescence (XRF), dan Induced Couple Plasma Mass Spectroscopy (ICP-MS).
Hasil yang diperoleh dalam penelitian ini menunjukkan bahwa ampas tebu, cangkang sawit, dan sekam padi terbukti mampu digunakan sebagai agen pereduksi alternatif pengganti batu bara. Pada penelitian ini, ampas tebu hanya mampu menghasilkan fasa wustite dalam reduction roasting bijih besi nikel laterite, di mana hasil reduksi tertinggi diperoleh pada sampel dengan rasio massa 1:4 yang direduksi pada temperatur 1000°C selama 30 menit. Sementara itu, cangkang sawit mampu mereduksi bijih besi nikel laterite menjadi Fe metal, dimana parameter optimalnya adalah: rasio massa = 1:3, durasi waktu reduksi = 30 menit, dan temperatur reduksi 1000°C. Di samping itu, meskipun sekam padi hanya mampu mereduksi bijih besi sampai fasa magnetite (dimana hasil optimal diperoleh pada penambahan padi sebesar 20%), tetapi dari sekam padi berhasil diperoleh bio-silika amorf dengan tingkat kemurnian 99,99% dan specific surface area (luas permukaan spesifik) 192 m2/g.

In general, this study aims to explore the utilization of local biomass as renewable reducing agents in the reduction roasting of Indonesian nickel laterite iron ore. The motive behind this research is to increase the added value of low grade iron ore and to obtain reducing agents to substitute coal in the reduction process. In this study, the three of biomass which have potential to be used as reducing agents for coal substitutes in reducing nickel laterite iron ore from Sorowako, are: bagasse from Cirebon, palm shells from Palangkaraya - Central Kalimantan, and rice husk from Kerawang - Jawa Barat. The reduction method used is reduction roasting with various temperature, mass ratio, and reduction time. And the analysis is based on the diffraction pattern of X-Ray Diffraction (XRD), X-Ray Fluorescence (XRF), and Induced Couple Plasma Mass Spectroscopy (ICP-MS).
The results obtained in this study indicate that bagasse, palm kernel shells, and rice husks have been proven to be able to be used as an alternative reducing agent for coal substitution. In this study, bagasse was only able to produce the wustite phase in the reduction roasting of nickel laterite iron ore, where the highest reduction results were obtained in samples with a mass ratio of 1: 4 which was reduced at a temperature of 1000°C for 30 minutes. Meanwhile, palm kernel shells could reduce nickel laterite iron ore to Fe metal, where the optimal parameters were: mass ratio = 1: 3, reduction time duration = 30 minutes, and reduction temperature = 1000°C. In addition, although rice husk was only able to reduce iron ore to magnetite phase (where optimal results are obtained by adding rice by 20%), but from rice husk it was successfully obtained amorphous bio-silica with a purity level of 99.99% and specific surface area 192 m2/g."
Depok: Universitas Indonesia, 2019
D2617
UI - Disertasi Membership  Universitas Indonesia Library
cover
Yunisa Vaditasari
"Instalasi Pengolahan Air Minum (IPAM) di Indonesia selalu menghasilkan residu lumpur yang sebagian besar langsung dibuang ke badan air tanpa pengolahan terlebih dahulu. Salah satu upaya untuk mengurangi lumpur yang dibuang ke badan air adalah dengan memanfaatkan kembali lumpur ke dalam proses Koagulasi-Flokulasi-Sedimentasi (KFS). Dalam aplikasi pada penelitian ini, pemanfaatan lumpur dilakukan dengan lima variasi yaitu penentuan dosis optimum koagulan, dosis optimum lumpur, dosis lumpur pada dosis optimum koagulan, dan dosis koagulan pada dosis optimum lumpur. Setelah seluruh variasi dilakukan dilanjutkan dengan identifikasi variabel bebas yang signifikan melalui full factorial design.
Metode yang digunakan adalahjartest menggunakan air baku Sungai Ciliwung dan lumpur IPAM Cibinong serta koagulan alum (Al2(SO4)3). Pada kajian penentuan dosis optimum koagulan divariasikan mulai dari 10 ppm - 50 ppm. Pada kajian penentuan dosis lumpur terlebih dahulu dilakukan uji karakteristik lumpur yang menentukan lumpur yang akan digunakan. Variasi pemanfaatan kembali lumpur dimulai dari 1%-10% dengan interval 1% dalam volume 500 mL beaker glass. Dalam setiap variasi yang dilakukan, dihitung parameter-parameter yang mempengaruhi kajian tersebut antara lain kekeruhan, suhu, pH, KMnO4, Fe, dan Koliform total.Lumpur yang tepat digunakan berupa lumpur sedimentasi Kombinasi paling tepat adalah variasi ke-5 dengan kombinasi dosis optimum lumpur sebesar 5% dan dosis koagulan 37.5 ppm. Penyisihan kekeruhan berturut-turut 97.46% & 97.23%, KmnO4 18.23% & 13.3%, Fe 84% & 85.74%, serta koliform total sebesar 98.86% dengan pH 6.69 dan suhu 27.5°C.
Hasil ini didukung dengan identifikasi variabel bebas dengan metode full factorial design dimana hasil paling signifikan dalam menyisihkan kekeruhan dan koliform total adalah interaksi antara koagulan dan lumpur dan dalam menyisihkan KmnO4 dan Fe adalah dosis koagulan. Pemanfaatan kembali lumpur tidak dapat mengurangi pemakaian koagulan, namun dapat meningkatkan efisiensi penyisihan kontaminan.

Water Treatment Plant (WTP) in Indonesia always produce sludge residuals that are directly discharged into the water body without being processed first. One of the measures to reduce sludge that is discharged into the water bodies is to reuse sludge in coagulation-floculation-sedimentation (K-F-S) processes. In the application of this study, sludge resirculation is conducted with five variations which are the optimum dosage of coagulant, the optimum dosage of sludge, sludge dosage at optimum dosageof coagulant, coagulant dosage at optimum dosage of sludge. After all variations conducted, continue with identification of significant independent variables using full factorial method.
The method used is jartest using raw water from Ciliwung River and Sludge from IPAM Cibinong with alum coagulant (Al2(SO4)3). In studies deterimining the optimum coagulant dose varied 10 ppm - 50 ppm. In determining optimum dose of sludge first tested the sludge characteristics to determine the sludge that will be used. Sludge reuse varied from 1%-10% with 1% intervalin500 mL volume of beaker glass. Parameters tested from each variations are turbidity, temperature , pH, KMnO4, Fe, and Total Coliform. Sludge use is sedimentation sludge. The most appropriate combination is the fifth variation with 5% sludge optimum dosage and coagulant optimum dosage 37.5 ppm. Allowance turbidity removal were 97/46% & 97.23%, KMnO4 18.23% & 13.3%, Fe minerals 84% & 85.74%, and total coliform 98.86% with pH 6.69 and temperature 27.5°C.
This result is supported by independent variables identification with full factorial design method which the most significant in removing turbidiy and total coliform in water is interactions between coagulant and sludge and in removing KMnO4 and Fe is coagulant dosage. Sludge reuse cannot reduce coagulant dosage, but able to improve contaminant removal efficiency.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
S52998
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>