Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 112901 dokumen yang sesuai dengan query
cover
Batubara, Lian Putra Panuturi
"Indonesia sebagai negara kepulauan memiliki potensi besar dalam industri besi dan baja. Maka dari itu potensi Indonesia di industri besi dan baja harus dikembangkan untuk meningkatkan perekonomian masyarakat. Sehingga diperlukan teknologi untuk memanfaatkan potensi yang ada. Tanur putar merupakan salah satu contoh teknologi yang dapat digunakan. Pada tanur putar terjadi reduksi langsung bijih besi bongkah menjadi besi spons. Proses reduksi langsung dilakukan dengan menggunakan reduktor arang batok kelapa. Pada proses reduksi langsung terdapat parameter-parameter yang mempengaruhi reduksi langsung salah satunya adalah ukuran bijih besi yang digunakan.
Penelitian ini dilakukan untuk mengetahui pengaruh ukuran bijih, ukuran bijih yang digunakan adalah 1 cm, 2 cm, dan 3 cm. Hasil reduksi diuji dengan menggunakan XRD (X-Ray Diffraction). Hasil menunjukkan bahwa terjadi reduksi dari Fe2O3 menjadi Fe3O4 dan bijih berukuran 1 cm merupakan bijih yang mengalami reduksi paling optimal. Dapat disimpulkan bahwa bijih 1 cm merupakan ukuran yang paling optimal untuk proses reduksi langsung.

Indonesia as an archipelago has great potential in the iron and steel industry. Thus the potential in the iron and steel industry should be developed to improve the community's economy. A necessary technology needed to exploit the potential. Rotary kiln is one technology that can be used. Inside, direct reduction occurs reducing lump ores into sponge irons. Direct reduction process is done using coconut charcoal as a reductant. There are parameters that affect the direct reduction process, one of them is the ore size.
This study was conducted to determine the effect of ore size, ore used is 1 cm, 2 cm, and 3 cm. Reduction results tested using XRD (X-Ray Diffraction). The results showed that reduction occurs, reducing of Fe2O3 into Fe3O4 and 1 cm-sized ore is the optimally reduced ore. It can be concluded that the ore 1 cm is the optimal size for the direct reduction process.
"
Depok: Fakultas Teknik Universitas Indonesia, 2014
S57500
UI - Skripsi Membership  Universitas Indonesia Library
cover
Romualdo, Libertinus Juan
"Proses reduksi langsung bijih besi menjadi besi spons salah satunya adalah dengan menggunakan teknologi rotary kiln dimana bijih besi akan dibakar bersamaan dengan reduktor pada temperature tinggi dan akan diputar berlawanan arah jarum jam. Pada penelitian ini reduktor yang digunakan adalah arang batok kelapa. Terdapat beberapa parameter proses reduksi langsung pada rotary kiln salah satunya adalah kecepatan putar. Pada penelitian ini dilakukan investigasi pengaruh kecepatan putar dalam berbagai putaran per menit terhadap senyawa besi yang dihasilkan pada proses reduksi langsung. Kecepatan putar yang dioperasikan antara lain 0.75 rpm, 1.0 rpm, 1.5 rpm, 2.0 rpm, dan 2.5 rpm. Kandungan senyawa besi yang dihasilkan diinvestigasi menggunakan X-Ray Diffraction (XRD). Hasil pengujian menunjukkan senyawa besi yang terbentuk pada hasil akhir reduksi langsung yaitu hematit (Fe2O3) dan magnetit (Fe3O4). Selain itu didapatkan nilai kecepatan putar optimal pada 1.0 rpm dengan mengukur nilai intensitas hasil karakterisasi XRD.

Rotary kiln is one of technologies which support the sponge iron making in direct reduction process. Iron lump ore will be burnt together with coconut shell charcoal as reductor at high temperature while rotary kiln rotates in counterclockwise movement. This process has several parameters include rotation speed. This research investigates rotation speed effect to the sponge iron making process. The rotation speed is operated in various numbers that are 0.75 rpm, 1.0 rpm, 1.5 rpm, 2.0 rpm, 2.5 rpm. The iron compounds was investigated by using X-Ray Diffraction (XRD) method. The results showed that direct reduction process produces hematite (Fe2O3) and magnetite (Fe3O4) compound. Furthermore, the optimal rotation speed was determined and investigated by using X-Ray Diffraction with the value of iron compunds as the consideration. The results showed that 1.0 rpm is the most optimal rotation speed to applied in this technology."
Depok: Fakultas Teknik Universitas Indonesia, 2014
S56228
UI - Skripsi Membership  Universitas Indonesia Library
cover
"[Indonesia adalah Negara yang kaya akan sumber daya alam salah satunya adalah bijih besi. Pada proses pengolahannya bijih besi memerlukan reduktor. Reduktor yang dipakai pada proses kali ini adalah biomass yaitu cangkang kelapa sawit mengingat Indonesia merupakan produsen kelapa sawit terbesar di dunia. Pada penelitian kali ini dilakukan proses reduksi langsung bijih besi menggunakan cangkang kelapa sawit sebagai reduktor pada muffle furnace. Bijih besi yang digunakan adalah besi laterit Kalimantan dengan ukuran 18#. Cangkang kelapa sawit yang digunakan berasal dari Kalimantan dengan ukuran 0.5 cm. Hal yang ingin dicapai pada penelitian ini adalah mengetahui pengaruh waktu reduksi pada suhu 1000oC. Penelitian ini menggunakan perbandingan rasio massa bijih besi dan cangkang kelapa sawit yaitu 1:3 pada suhu 1000oC dengan waktu 30, 60, 90, 120, dan 150 menit. Bijih besi dicampur dengan cangkang kelapa sawit dalam crucible dan kemudian dimasukkan dalam muffle furnace. Hasil XRD menunjukkan bahwa pada variabel waktu 120 menit terbentuk Fe dengan intensitas yang paling tinggi dibanding variabel lainnya.
, Indonesia is a country that have many natural resources, one of them is iron ore . In the iron ore reduction process requires a reducing agent. Reducing agents used in this process is palm kernel shell considering Indonesia is the largest palm oil producer in the world. In this study iron ore is processed by direct reduction method using palm kernel shell as a reducing agent in the muffle furnace . The iron ore is laterite ore from Kalimantan with size about 18#. The palm kernel shell from Kalimantan with size about 0.5 cm. The research objective is to determine the effect of reduction time at 1000oC. This study uses the mass ratio of iron ore and bagasse 1 : 3 at 1000oC on 30, 60, 90, 120, 150 minutes . Iron ore is mixed with palm kernel shell in the crucible and then was put in a muffle furnace . XRD results showed that the variable reduction time of 120 minutes formed Fe with the highest intensity compared to other variables
]"
Fakultas Teknik Universitas Indonesia, 2016
S62640
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rajagukguk, Esaputra Mangarul
"ABSTRAK
Proses reduksi bijih besi adalah proses pemisahan besi yang terkandung dalam
bijih besi dari oksigen dan pengotornya. Pada penelitian kali ini dilakukan reduksi
langsung bijih besi bongkah dengan reduktor arang tempurung kelapa pada rotary
kiln sederhana. Sampel yang digunakan adalah bijih besi laterit dari Kalimantan
dengan ukuran 1-2 cm dengan rasio bijih dan reduktor sebanyak 1:2. Putaran
rotary kiln sebesar 2,5 rpm dengan temperatur proses berkisar antara 650-702oC.
Tujuan penelitian adalah mengetahui pengaruh waktu pada reduksi langsung bijih
besi. Penelitian dilakukan dengan 4 variasi waktu, yaitu 15 menit, 30 menit, 45
menit dan 60 menit. Hasil penelitian menunjukkan terbentukya produk reduksi
Fe3O4 pada semua variabel waktu dengan hasil tertinggi didapat pada waktu 15
menit

ABSTRACT
Iron ore reduction process is the process of separating iron contained in iron ore of
oxygen and impurities. In this research, direct reduction in rotary kiln was
examined with Kalimantan lateritic iron ore and coconut shell charcoal as the
reductor. Iron ore that was used have particle size between 1-2 centimeters with
mass ratio of ore and reductor in amount of 1:2. RPM of rotary kiln was 2,5 and
temperature of process in range of 650-702oC. The research objective was to
determine the effect of time in direct reduction process. Four time variation was
examined, which were 15, 30, 45 and 60 minutes. The result indicated that Fe3O4
was formed in all time condition. The optimum amount of reduction product was
achieved at 15 minutes."
Fakultas Teknik Universitas Indonesia, 2014
S57582
UI - Skripsi Membership  Universitas Indonesia Library
cover
Mohammad Iqbal
"Salah satu cara mereduksi bijih besi tersebut dengan menggunakan rotary kiln. Rotary kiln pada umumnya memiliki panjang 100m dan diameter 3m, namun pembangunan rotary kiln tersebut membutuhkan biaya modal serta biaya operasi yang tinggi. Rotary kiln sederhana memiliki panjang 3m dan diameter 40cm. Proses yang berlangsung di rotary kiln sederhana merupakan proses reduksi langsung yang menggunakan arang sebagai reduktor, blower sebagai pensuplai oksigen, rotor sederhana sebagai penggerak. Terdapat beberapa parameter proses reduksi langsung pada rotary kiln salah satunya adalah variasi reduktor. Pada penelitian ini dilakukan investigasi pengaruh perbedaan reduktor terhadap senyawa besi yang dihasilkan pada proses reduksi langsung. Reduktor sebelumnya diukur nilai GCV dengan bomb calorimeter dan analisa proksimat. Reduktor yang digunakan sebagai perbandingan yaitu arang kayu, arang batok, dan briket batubara. Kandungan senyawa besi yang dihasilkan dianalisa menggunakan X-Ray Diffraction (XRD). Hasil pengujian menunjukkan bahwa arang kayu memiliki hasil paling optimal dengan senyawa besi yang terbentuk pada hasil akhir reduksi langsung yaitu hematit (Fe2O3) dan magnetit (Fe3O4).

Rotary kiln is one of many way to process an iron ore. Rotary kilns generally have a length of 100m and 3m in diameter, but the manufacture of the general rotary kiln has high capital and operating costs. Simple rotary kiln has a length of 3m and 40cm in diameter. The process that takes place in a simple rotary kiln is a direct reduction process that uses charcoal as , the blower as a supplier of oxygen, and the rotor as a mover. There are several parameters in the direct reduction process rotary kiln one of which is a variation of reductant. In this research, i investigate the effect of different reductant on iron compounds produced on the direct reduction process. Reductant previously measured value of GCV with bomb Calorimeter and proximate analysis. Reductant are used for comparison, wood charcoal, coconut shell charcoal, and coal briquettes. The content of iron compounds produced were analyzed using X-Ray Diffraction (XRD). The test results showed that charcoal has the most optimal results with iron compounds that are formed on the end result which is a direct reduction of hematite (Fe2O3) and magnetite (Fe3O4)."
Depok: Fakultas Teknik Universitas Indonesia, 2014
S55794
UI - Skripsi Membership  Universitas Indonesia Library
cover
Amanda Arief Putra
"Sumber cadangan bijih besi yang terdapat di Indonesia tersebar di seluruh kepulauan sehingga dibutuhkan usaha untuk mengolah cadangan tersebut untuk meningkatkan perekonomian. Mengingat UU No.4 Tahun 2009 yang berisikan tentang pengolahan mineral yang ada di Indonesia dilakukan didalam negeri. Berdasarkan kedua hal tersebut maka dibutuhkan sebuah teknologi sederhana yang dapat mengolah bijih besi tersebut hingga mendapatkan konsentrasi yang lebih tinggi dengan biaya yang terjangkau dan ramah lingkungan.
Penelitian ini dilakukan dengan menggunakan bijih besi laterit dari Kalimantan dan arang batok kelapa. Perbandingan rasio massa antara bijih besi dan arang batok kelapa divariasikan menjadi 1:1, 1:2, dan 1:3. Kedua material ini dicampur dan dibakar hingga api menyebar merata. Kemudian dimasukkan ke Rotary Kiln, blower dinyalakan dan ditahan selama 15 menit. Kemudian Rotary Kiln diputar dan dikondisikan proses berlangsung selama 30 menit. Karakterisasi dilakukan dengan XRD untuk melihat secara kualitatif hasil reduksi dan efisiensi proses.
Hasil XRD menunjukkan bahwa semakin banyak reduktor maka semakin terbentuk hasil reduksi. Terbukti peak maksimal pada 2θ antara 20-40 menunjukkan kenaikan dari setiap perbandingan rasio yang ada, dari intensitas 330 ke 630 (contoh perbandingan 1 : 2) dari peak maksimum Fe3O4. Hasil reduksi yang paling efisien terdapat pada perbandingan 1:2. Hal ini dikarenakan perubahan intensitas yang dimiliki antara perbandingan 1:2 dan 1:3 tidak terlalu signifikan.

Iron ore sources are located in all of island of Indonesia so it takes some effort to process the sources to improve economic matters. Based on UU No.4 Tahun 2009 which requires that raw mineral mined must be processed in Indonesia. So, we need simple technology which can process iron ore with low cost and green.
This research was use laterit iron ore from Kalimantan and coconut charcoal. Mass rasio beetwen iron ore and coconut charcoal variated to 1:1, 1:2 and 1:3. Both of them was mixed and burned until fire spread evenly. After that, both of them get into Rotary Kiln and blower was turned on. After that sample was holded in 15 minute. Then, Rotary Kiln was turned on and prosess did in 30 minute. Characterization use XRD to see in qualitative reduction result and efficiency process.
XRD result showed, if there more reductor so more formed reduction result. it proved with intensity of maximum peak of Fe3O4 was ascent in every ratio, from 330 to 630 (example in Ratio 1 : 2). Efficient Process there in ratio 1 : 2, it proved that reduction result beetwen ratio 1 : 2 and 1 : 3 was not significanly changed.
"
Depok: Fakultas Teknik Universitas Indonesia, 2014
S55799
UI - Skripsi Membership  Universitas Indonesia Library
cover
Robby Krisnaldo Elvin
"Mineral mangan merupakan salah satu mineral yang paling banyak ditemui di kerak bumi. Sebagian besar produksi mangan dan paduannya di dunia saat ini diserap oleh industri baja. Ferromangan merupakan salah satu logam paduan dengan kandungan mangan yang sangat tinggi, yaitu sekitar 65 - 90%. Sebanyak 90%, ferromangan digunakan untuk menambahkan unsur mangan kedalam material baja untuk memperbaiki sifat-sifat mekanik dari material baja, seperti kekuatan, hardenability, dan ketahanan terhadap aus. Penelitian ini bertujuan untuk mengetahui pengaruh penambahan kadar kokas terhadap keefisienan proses reduksi bijih mangan lokal kadar menengah menjadi produk ferromangan. Proses reduksi dilakukan pada tungku submerged arc furnace tiga fasa dengan kapasitas 100 Kg/Batch dilengkapi dengan tiga buah elektroda grafit. Setiap percobaan menggunakan 30 Kg bijih mangan lokal, 12 Kg limestone, dan kadar kokas yang bervariasi, yaitu 5,5 Kg (18,33%), 7,5 Kg (25,00%), 9,5 Kg (31,67%), dan 11,5 Kg (38,33%). Hasil penelitian menunjukkan bahwa kuantitas dan kualitas produk ferromangan yang dihasilkan meningkat seiring dengan bertambahnya kadar kokas yang digunakan. Dimana kandungan mangan pada ferromangan dan massa/yield produk ferromangan cenderung meningkat. Kandungan mangan pada produk ferromangan tertinggi sebesar 78% pada pengujian menggunakan kokas sebanyak 7,5 Kg (25,00%). Sedangkan massa produk ferromangan tertinggi terdapat pada pengujian dengan menggunakan kokas sebanyak 9,5 Kg (31,67%), yaitu 12,8 Kg. Dan pada penggunaan energi selama proses berlangsung cenderung menurun dengan penambahan kokas, dimana penggunaan energi terendah selama proses reduksi berlangsung pada pengujian menggunakan kokas sebanyak 9,5 Kg (31,67%) sebesar 7,03 KWh/Kg. Namun konsumsi elektroda cenderung meningkat. Sehingga konsumsi elektroda grafit terendah pada saat menggunakan kokas 5,5 Kg (18,33%), yaitu sebesar 0,75 Kg. Berdasarkan aspek ekonomi, pengujian dengan keuntungan tertinggi terdapat pada pengujian menggunakan kokas sebanyak 9,5 Kg (31,67%) yaitu sebesar Rp 62.565 pada tiap satu kali pengujian.

Manganese is one of the most common minerals in the earth’s crust.Manganese plays an important role in the development of various steel making processes and its continuing importance is indicated by the fact that about 90% of all manganese alloys consumed annually goes into steel production as an alloying element in the form of ferromanganese. Ferromanganese is one of the metal alloys with a high content of manganese, which is about 65 - 90%. Manganese has four functions to steel such as desulphurizing agent, deoxidation agent, enhancing hardness, and wear resistance. This research, studies have been made to obtain the most optimum raw material composition to produce ferromanganese metal based on local medium grade manganese ore with various amount of cokes as its main variable. The process is conducted four times by smelting manganese ore into ferromanganese metal in mini submerged arc furnace (SAF) technology using three graphite electrodes. The process begin with using 30 kg of medium grade manganese ore from Jember, East Jawa-Indonesia, 12 kg of limestone as its fluxing agent, and various number of cokes from 5,5 kg (18,33%), 7,5 kg (25%), 9,5 kg (31,67%), and 11,5 kg (38,33%). Influence of various amount of cokes being used in this study have been investigated. The experiment conducted by increasing number of cokes carried out good results. Higher consumption of cokes will produce bigger number of ferromanganese metal and also the manganese content inside it. The most optimum composition of cokes shown by this study is 9,5 kg (31,67%), producing the biggest number of product at 12,8 kg of ferromanganese and consuming the least energi at 7,03 kwh/kg FeMn. The other result also showed that adding 7,5 kg (25%) of cokes will produce 78% manganese content inside the metal which was the highest manganese content. However, with an increase of cokes, the electrode consumption will also increase. The experiment with 5,5 kg (18,33%) of cokes carried out the least electrodes consumption at 0,75 kg/process. Moreover, to support the optimum raw material composition, economic evaluation has been conducted. The biggest profit is Rp 62.565,-/process for 9,5 kg (31,67%) of cokes.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S61950
UI - Skripsi Membership  Universitas Indonesia Library
cover
Desrandy Andriyanda
"Saat ini produksi besi di dunia masih didominasi oleh proses blast furnace. Dengan terus bergulirnya isu penghematan energi dan mahalnya harga kokas, maka peluang untuk penggunaan proses reduksi langsung akan semakin besar, mengingat proses reduksi langsung hanya menggunakan batu bara sebagai pereduksi. Pembuatan Fe metal dengan metode reduksi langsung dilakukan dengan cara besi direduksi dalam bentuk pellet dimana dilakukan proses komposit terlebih dahulu dengan batubara dan kapur.
Penelitian ini dilaksanakan untuk mengetahui kinetika dari proses reduksi langsung, pembentukan Fe metal, dan mendapatkan nilai energi aktivasi. Proses reduksi dilakukan dalam tube furnace dengan variabel waktu 2 menit, 4 menit, 7 menit, 10 menit, dan variabel temperatur 11000C, 12000C, 13500C. Energi aktivasi yang dihasilkan 28,1 kJ/mol untuk model first order, 28,7 kJ/mol - 32,9 kJ/mol untuk model Avrami Erofeev. Pembentukan besi dimulai dari bagian tengah pellet menuju bagian luar.

Currently, the production of iron in the world is still dominated by the blast furnace process. With the continued passing of the issue of energy saving and high prices of coke, the opportunity to use direct reduction process will be greater, considering only the direct reduction process using coal as a reductant. Preparation of Fe metal with a direct reduction method conducted by reduced iron in the form of pellets which made the first composite with coal and lime.
This study was conducted to determine the kinetics of the direct reduction process, the formation of Fe metal, and get the value of the activation energy. Reduction process carried out in a tube furnace with a variable time of 2 minutes, 4 minutes, 7 minutes, 10 minutes, and variable temperature 1100 0C, 1200 0C, 1350 0C. The resulting activation energy 28.1 kJ / mol for the model of first order, 28.7 kJ / mol - 32.9 kJ / mol for the model Avrami Erofeev. Iron formation starts from the center toward the outside of the pellet.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
S44388
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sulthan Nabil
"Banyaknya bijih besi cadangan lateritik di Indonesia menimbulkan potensuial yang besar untuk memperkaya produksi besi dan besi baja untuk sektor industri Indonesia. Metode yang digunakan dalam mengekstraksi bijih besi lateritik tersebut umumnya adalah Direct reduction. Namun terdapat beberapa fasa slag yang terbentuk pada Direct reduction. Skripsi ini membahas tentang transformasi fasa yang dialami oleh bijih Goethite (FeOOH) dari Sebuku yang di proseskan dalam Direct Reduction dengan temperatur 1000-1200oC selama waktu tahan 30 menit – 60 menit dengan variabel batubara sub-bituminous 24% dan 16% pada campurannya. Hasil dari sponge iron yang didapatkan akan di-analisa menggunakan SEM-EDS dan XRD, untuk mendapatkan hasil yang akurat mengenai transformasi fasa yang terjadi pada bijih Goethite. Hasil yang didapatkan adalah terbentuknya fasa Fe metal, Spinel – Fe Metal + Spinel ,dan Wustit. Dengan hasil recovery terbaik diraih pada temperatur 1000oC pada komposisi batubara 24%. Fasa slag yang terbentuk adalah spinel dan Fe Metal + Spinel.

Abundance of lateritic iron ore in Indonesia opens big potentials for Indonesia to intensify the production of ironworks and steelworks. The method to extract the lateritic ores is by Direct reduction. But in the process of Direct reduction there is some slags to be expected. The focus of this thesis is about phase transformation that occurs in Goethite ore (FeOOH) from Sebuku Mines that been processed in a Direct Reduction of 1000-1200oC with the holding time of 30 minutes – 60 minutes in a mixture of 24% and 16% sub-bituminous coal. The sponge iron that been resulted from the process is characterized with SEM-EDS and XRD, to acquire a precise and accurate data of phase transformation from the Goethite ore. The result of phase identification are Fe Metal, Spinels, Fe Metal + Spinels , and Wustites in all composition. The most high recovery value is from temperature 1000oC with the coal mixture of 24%. The slags are identified as spinels and Fe Metal + Spinels."
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Fahmi Fazri
"Makin langkanya bahan baku bijih besi mendorong banyak pihak mulai menggunakan bijih laterit. Laterit sebagai salah satu hasil tambang yang banyak didapatkan di Indonesia. laterit merupakan bijih besi yang memiliki kandungan Fe2O3 yang tinggi. Agar dapat digunakan, bijih besi laterit (Fe2O3) harus direduksi untuk mendapatkan besi (Fe). Proses pengolahan laterit yang ada saat ini adalah dengan mereduksi langsung dengan batubara pada temperatur proses sekitar 1350°C. Hal ini dinilai tidak efisien karena membutuhkan energi yang banyak untuk menghasilkan temperatur yang sangat tinggi. Tingginya energi yang dibutuhkan berpengaruh dengan biaya produksi yang sangat tinggi. Yang menyebabkan industri di Indonesia tidak dapat bersaing dengan industri-industri dari negara lain. Oleh karena itu, dengan analisa pengaruh temperatur dari percobaan suatu metode reduksi langsung yang dilakukan pada temperatur yang lebih rendah bertujuan untuk mendapatkan temparatur yang efisien yang menghasilkan besi yang tinggi tapi dalam temperatur lebih rendah untuk menghasilakan besi dari bijih laterit, sehingga diharapkan biaya produksi akan menurun. Reduksi langsung yang dilakukan adalah dengan cara memanaskan laterit yang telah dicampur dengan batubara dalam oven. Yang akan diteliti pada penelitian ini adalah pengaruh temperatur proses reduksi yang terjadi. Pengaruh dari temperatur yang dianalisa dilakukan pada komposisi Fe2O3 dan C yang berbeda untuk setiap waktu pemanasan (10, 20, dan 30 menit). Variasi temperatur yang digunakan adalah 700°C, 900°C, dan 1000°C . Hasil dari penelitian ini, didapatkan bahwa dengan temperatur reduksi 900°C dan 1000°C menghasilkan intensitas Fe yang cukup besar. Sedangkan pada temperature 700°C secara umum tidak terbentuk Fe.

The scarce of iron ore make people to use laterite. Laterite is one of primary mining commodity that exists in Indonesia. Laterite is an iron ore that contains high Fe2O3. Laterite iron ore must be reduced to get the iron (Fe) before it can be used. Nowadays, the processing of laterite is direct reduction with coal in the process temperature about 1350°C. This process is not efficient because need a lot of energy to gain very high temperature. Higher energy that is needed by the process will let to the higher cost. That cause industries in Indonesia cannot compete with the industries from other countries. Therefore, with the study of temperature effect in direct reduction at lower temperature in order to find the efficient temperature to produce high intensity of irons from laterite, so that lowering the production cost. The direct reduction is done by heating laterite that had been mixing with coal in the oven. Focus of this research is study of temperature effect in direct reduction process. The effect of temperature that analyzed is in the different compositions of Fe2O3 and C in each heating temperature which is 10, 20, and 30 minutes. The variations of temperature are 700°C, 900°C, and 1000°C. The results of this research are the reduction temperature 900°C and 1000°C produce high intensity of Fe, and in 700°C generally Fe does not form."
Depok: Fakultas Teknik Universitas Indonesia, 2007
S41787
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>