Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 106366 dokumen yang sesuai dengan query
cover
Muhammad Fatah Karyadi
"Penelitian ini mengevaluasi kinerja absorpsi gas CO2 melalui membran kontaktor superhidrofobik. Kinerja kontaktor membran superhidrofobik ini ditinjau dari empat parameter utama dengan variasi laju alir pelarut Air (100, 150, 200, 250, 300, 400 dan 500 mL/menit) dan jumlah serat membran kontaktor (2000, 4000 dan 6000). Hasil penelitian ini menunjukkan bahwa kenaikan laju alir pelarut Air meningkatkan kinerja kontaktor membran superhidrofobik, dalam hal koefisien perpindahan massa, fluks dan efisiensi penyerapan CO2. Kenaikan jumlah serat membran juga akan meningkatkan koefisien perpindahan massa dan fluks CO2.
Koefisien perpindahan massa dan fluks CO2 tertinggi yang didapatkan pada penelitian ini berturut-turut adalah 1,69 x 10-4 cm/s dan 1,7 x 10-5 mmol/cm2s pada laju alir Air 500 mL/menit dan jumlah serat membran 6000. Sedangkan efisiensi penyerapan CO2 tertinggi adalah 29,5% pada laju alir Air 500 mL/menit juga pada jumlah serat membran 6000.

This study evaluated the performance of absorption of CO2 through the superhydrophobic contactor membrane. Superhydrophobic contactor membrane performance is evaluated from four main parameters with the variation of solvent flow rates of water (100, 150, 200, 250, 300, 400 and 500 mL/min) and the amount of contactors membrane fibers (2000, 4000, and 6000). The results of this study indicate that the increase in the flow rate of the water solvent, increases superhydrophobic contactor membranes performance in terms of mass transfer coefficient, flux, and the efficiency CO2 absorption. The increase in the number of membrane fibers also increases the mass transfer coefficient and CO2 flux.
The mass transfer coefficient and the highest CO2 flux were obtained in this study are 1.69 x 10-4 cm/s and 1.7 x 10-5 mmol/cm2s respectively when water flow rate is 500 mL/min and the amount of fiber membranes is 6000. The highest CO2 absorption efficiency is 29.5% when water flow rate is 500 mL/min and the amount of membrane fiber is 6000.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S69957
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rexy Darmawan
"Penyerapan gas CO2 memiliki peran yang vital dalam industri gas alam. Teknologi alternatif untuk proses penyerapan CO2 ialah kontaktor membran serat berongga. Teknologi kontaktor membran ini dapat mengatasi kelemahan yang dimiliki kolom konvensional. Namun dalam prakteknya kontaktor membran masih memiliki kekurangan seperti permasalahan pembasahan membran oleh pelarut. Oleh karena itu penelitian ini akan menguji pengaruh laju alir pelarut dan jumlah serat membran dalam kinerja penyerapan gas CO2 murni melalui kontaktor membran serat berongga dengan bahan material membran bersifat superhidrofobik. Pelarut yang digunakan dalam penelitian ini adalah larutan DEA 5% volum. Variabel bebas yang digunakan pada penelitian ini ialah laju pelarut dan jumlah serat membran. Laju pelarut yang digunakan antara 100-500 cm3/menit, sedangkan jumlah serat membran 2000, 4000 dan 6000. Setiap percobaan dilakukan pada laju gas CO2 sebesar 240 cm3/menit. Parameter kinerja perpindahan massa yang dihasilkan pada penelitian ini yaitu efisiensi penyerapan 56%, laju CO2 terabsorpsi 9x10-2 mmol/s, koefisien perpindahan massa 6x10-4 cm/s, fluks CO2 1,85x--5 mmol/cm2.s, serta acid loading 9,5x10-2.

The absorption of CO2 gas has a vital role in the natural gas industry. A promising alternative technology that overcome the disadvantages of conventional gas absorption is hollow fiber membrane contactor. However, in practice, contactor membrane still has problem such as wetting membrane by the solvent. Therefore this study evaluates the effect of solvent flow rate and the number of fibers in pure CO2 gas absorption performance through superhydrofobic hollow fiber membrane contactor using DEA 5%-volume as solvent. The abosrbent that we used in this research is diethanolamine (DEA) with the concentration 5 %-v. Independent variables in this research are solvent flow rate and the number of fibers. Solvent flow rate that we used between 100-500 cm3/minute, and for the amount of fibers are 2000, 4000 and 6000. Each of the experiments that conducted at the CO2 flow rate 240 cm3/minute. Results show that CO2 removal efficiency is 56%, while the rate of CO2 absorption is 9x10-2 mmol/s with overall mass transfer coefficient 6x10-4 cm/s, flux of CO2 absorption is 1.85x10-5 mmol/cm2.s and the acid loading is 9.5x10-2."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S62294
UI - Skripsi Membership  Universitas Indonesia Library
cover
Julian Christofer
"Kontaktor membran serat berongga digunakan untuk mengabsorpsi gas CO2 murni. Bahan membran yang digunakan adalah polipropilen dan pelarut yang digunakan merupakan pelarut campuran senyawa amina (MEA/DEA) dan dibandingkan pelarut tunggal DEA. Penelitian ini menganalisis efektivitas perpindahan massa dengan menghitung nilai koefisien perpindahan massa (kL), fluks, dan korelasi perpindahan massa pada variasi laju alir pelarut 200,250,300,350,400 ml/menit dan jumlah serat 20,30,40. Hasil dari penelitian ini menunjukkan bahwa pelarut campuran MEA/DEA lebih efektif menyerap gas CO2 dibandingkan pelarut tunggal DEA pada laju alir 400 ml/menit dan jumlah serat 40 dengan nilai kL, fluks dan sebesar 0.00244 cm/s dengan persentasi CO2 yang terabsorpsi sebesar 93%.

Hollow fiber membrane contactor was used for the absorption of pure carbon dioxide. The membranes applied were made of PVC and the absorbents included aqueous solution of mixed amine (MEA/DEA) that would be compared with single amine absorbent. This research detemined the mass transfer efficiency with determining mass tranfer coefficient, flux and mass transfer correlation under different absorbent flow rate 200,250,300,350,400 cc/minutes and number of fiber 20,30,40. The results showed that the mixed amine absorbent was more effective in doing absorption than the single amine under the flow rate absorbent 400 cc/minutes and number of fiber 40 with the value kL 0.00244 cm/s with percentage of CO2 absorped 93%."
Depok: Fakultas Teknik Universitas Indonesia, 2012
S43403
UI - Skripsi Open  Universitas Indonesia Library
cover
Annisa Larasati
"Karbon dioksida adalah senyawa yang banyak terdapat pada flue gas dan merupakan penyebab paling serius dari global warming. Teknologi pemisahan gas CO2 dari flue gas yang banyak digunakan hingga saat ini adalah kolom absorbsi konvensional. Teknologi alternatif baru yang potensial untuk pemisahan CO2 ini adalah kontaktor membran. Dalam penelitian ini akan diuji pengaruh konsentrasi pelarut dan laju alir gas serta jumlah serat membran pada kinerja penyerapan CO2 melalui kontaktor membran serat berongga superhidrofobik. Pelarut yang digunakan dalam penelitian ini adalah larutan polietilen glikol PEG . Variasi konsentrasi yang digunakan yaitu 5 , 10 , 15 , dan 20 -b/v. Variasi laju alir gas yang digunakan yaitu 134, 190, dan 288 mL/menit. Jumlah serat membran yang digunakan yaitu 1000, 3000, dan 5000. Setiap percobaan dilakukan pada laju alir pelarut sebesar 300 mL/menit. Sebelumnya, dilakukan uji hidrodinamik dimana rasio penurunan tekanan terbesar mencapai 1,67. Konsentrasi pelarut yang optimum yaitu pada rentang 5-10 -b/v. Parameter kinerja perpindahan massa yang dapat dicapai antara lain koefisien perpindahan massa 5,85x10-7 m/s, fluks perpindahan massa 2,18x10-5 mol/m2.s, acid loading 7,9x10-3 mol CO2/mol PEG, persentase penyerapan 25,82 , dan jumlah CO2 terabsorpsi 6,6x10-6 mol.

Carbon dioxide is a compound in flue gas and is the most serious cause of global warming. CO2 gas separation technology that is widely used is a conventional absorption column. A potential new alternative technologies for CO2 separation is a membrane contactor. In this research will be tested the effect of the concentration of the solvent, the gas flow rate and the number of membrane fibers in CO2 absorption performance through the superhydrophobic hollow fiber membrane contactor. The absorbent that we used in this research is polyethylene glycol PEG. The variation of solvent concentration used are 5 , 10 , 15 , and 20 w v. The variation of gas flow rate used are 134, 190, and 288 mL minute. The number of fibers used are 1000, 3000, and 5000. All experiments are being done with solvent flow rate of 300 mL minute. At first, hydrodynamic test was run and the biggest pressure drop ratio calculated is 1,67. The optimum range for solvent concentration is 5 10 w v. Mass transfer parameters reached in this experiments are 5,85x10 7 m s for mass transfer coefficient, 2,18x10 5 mol m2.s for mass transfer flux, 7,9x10 3 mol CO2 mol PEG for acid loading, 25,82 , for absorption efficiency, and 6,6x10 6 mol s for amount of absorbed CO2."
Depok: Fakultas Teknik Universitas Indonesia, 2017
S62749
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ainu Safira Corni
"[ABSTRAK
Penelitian ini mengevaluasi kinerja absorpsi gas CO2 dari campurannya dengan
CH4 melalui membran kontaktor superhidrofobik. Kinerja kontaktor membran
superhidrofobik ini ditinjau dari empat parameter utama dengan variasi laju alir
pelarut DEA (100, 300 dam 500 mL/menit) dan jumlah serat membran kontaktor
(2000 dan 8000). Hasil penelitian ini menunjukkan bahwa kenaikan laju alir pelarut
DEA meningkatkan kinerja kontaktor membran superhidrofobik, dalam hal
koefisien perpindahan massa, fluks dan efisiensi penyerapan CO2. Sedangkan
kenaikan jumlah serat membran akan menurunkan koefisien perpindahan massa
dan fluks CO2. Namun, meningkatkan efisiensi penyerapan CO2 dan acid loading.
Koefisien perpindahan massa dan fluks CO2 tertinggi yang didapatkan pada
penelitian ini berturut-turut adalah 2,31 x 10-4 cm/s dan 7,15 x 10-6 mmol/cm2s pada
laju alir DEA 500 mL/menit dan jumlah serat membran 2000. Sedangkan efisiensi
penyerapan CO2 tertinggi adalah 72% pada laju alir DEA 500 mL/menit dan jumlah
serat membran 8000.
ABSTRACT
This study evaluates performance of CO2 absorption from its mixture with CH4
through membran contactor superhydrophobic. Superhidrophobic membrane
contactor performance is observed using four main parameters by varying the flow
rate of solvent DEA (100, 300 dam 500 mL/min) and the number of fiber membrane
contactors (2000 and 8000). The results showed that increasing DEA solvent flow
rate increase superhidrophobic membrane contactor performance, in terms of mass
transfer coefficient, flux and efficiency removal of CO2. While increasing the
number of fiber membrane will reduce the mass transfer coefficient and CO2 flux.
However, it will increase the efficiency removal of CO2 and acid loading. The
highest mass transfer coefficient and CO2 flux obtained in this study are
respectively 2,31 x 10-4 cm/s and 7,15 x 10-6 mmol/cm2s on DEA flow rate of 500
mL/min and the number of fiber membranes 2000. The highest CO2 absorption
efficiency is 72% at DEA flow rate of 500 mL/min and the number of fiber
membranes 8000.;This study evaluates performance of CO2 absorption from its mixture with CH4
through membran contactor superhydrophobic. Superhidrophobic membrane
contactor performance is observed using four main parameters by varying the flow
rate of solvent DEA (100, 300 dam 500 mL/min) and the number of fiber membrane
contactors (2000 and 8000). The results showed that increasing DEA solvent flow
rate increase superhidrophobic membrane contactor performance, in terms of mass
transfer coefficient, flux and efficiency removal of CO2. While increasing the
number of fiber membrane will reduce the mass transfer coefficient and CO2 flux.
However, it will increase the efficiency removal of CO2 and acid loading. The
highest mass transfer coefficient and CO2 flux obtained in this study are
respectively 2,31 x 10-4 cm/s and 7,15 x 10-6 mmol/cm2s on DEA flow rate of 500
mL/min and the number of fiber membranes 2000. The highest CO2 absorption
efficiency is 72% at DEA flow rate of 500 mL/min and the number of fiber
membranes 8000.;This study evaluates performance of CO2 absorption from its mixture with CH4
through membran contactor superhydrophobic. Superhidrophobic membrane
contactor performance is observed using four main parameters by varying the flow
rate of solvent DEA (100, 300 dam 500 mL/min) and the number of fiber membrane
contactors (2000 and 8000). The results showed that increasing DEA solvent flow
rate increase superhidrophobic membrane contactor performance, in terms of mass
transfer coefficient, flux and efficiency removal of CO2. While increasing the
number of fiber membrane will reduce the mass transfer coefficient and CO2 flux.
However, it will increase the efficiency removal of CO2 and acid loading. The
highest mass transfer coefficient and CO2 flux obtained in this study are
respectively 2,31 x 10-4 cm/s and 7,15 x 10-6 mmol/cm2s on DEA flow rate of 500
mL/min and the number of fiber membranes 2000. The highest CO2 absorption
efficiency is 72% at DEA flow rate of 500 mL/min and the number of fiber
membranes 8000., This study evaluates performance of CO2 absorption from its mixture with CH4
through membran contactor superhydrophobic. Superhidrophobic membrane
contactor performance is observed using four main parameters by varying the flow
rate of solvent DEA (100, 300 dam 500 mL/min) and the number of fiber membrane
contactors (2000 and 8000). The results showed that increasing DEA solvent flow
rate increase superhidrophobic membrane contactor performance, in terms of mass
transfer coefficient, flux and efficiency removal of CO2. While increasing the
number of fiber membrane will reduce the mass transfer coefficient and CO2 flux.
However, it will increase the efficiency removal of CO2 and acid loading. The
highest mass transfer coefficient and CO2 flux obtained in this study are
respectively 2,31 x 10-4 cm/s and 7,15 x 10-6 mmol/cm2s on DEA flow rate of 500
mL/min and the number of fiber membranes 2000. The highest CO2 absorption
efficiency is 72% at DEA flow rate of 500 mL/min and the number of fiber
membranes 8000.]"
Fakultas Teknik Universitas Indonesia, 2016
S62292
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aulia Andika Putri
"Kini telah dikembangkan teknologi membran dengan kontaktor serat berongga yang dapat mengatasi permasalahan-permasalahan yang terjadi akibat pemisahan CO2 menggunakan kolom konvensional. Prinsip dari kontaktor membran ini menggunakan gaya penggerak berupa perbedaan konsentrasi. Namun terdapat kelemahan dari teknologi ini yaitu terjadi pembasahan membran oleh pelarut.
Oleh karena itu penelitian ini menguji pengaruh laju alir pelarut PEG, konsentrasi pelarut, dan jumlah serat membran dalam kinerja penyerapan gas CO2 melalui kontaktor membran serat berongga superhidrofobik. Efektivitas kinerja membran diukur berdasarkan parameter hidrodinamikanya.
Proses absorpsi ini merupakan absorpsi fisika, dimana gas CO2 sebagai zat terlarut dan polietilen glikol sebagai pelarut. Dengan variabel bebas dari penelitian ini yaitu laju alir pelarut PEG 100-500 cm3/menit, konsentrasi pelarut 5-20%, dan jumlah serat membran yaitu 1000, 3000, 5000.
Pada penelitian ini hasil optimum diperoleh pada laju alir pelarut 500 ml/menit dan jumlah serat 5000, untuk koefisien perpindahan massa (KL) sebesar 3,7x10-4 cm/s, efisiensi penyerapan (%R) sebesar 14,6%, fluks (J) sebesar 1,4x10-5 mol/cm2.s, dan acid loading sebesar 4x10-3. Sedangkan besar konsentrasi pelarut optimum 10%.

Now has developed technology hollow fiber membrane contactor that can overcome the problems caused by CO2 separation using conventional columns. The principle of this membrane contactor is using the driving force as different concentrations. But a weakness of this technology is going wetting membrane by the solvent.
Therefore, this study examined the effect of PEG solvent flow rate, the concentration of the solvent, and the amount of fiber membranes in CO2 gas absorption performance through the hollow fiber membrane contactor superhydrophobic. Effectiveness of membrane performance is measured based on the parameters their hydrodinamics.
This absorption process is a physical absorption, where CO2 as a solutes and polyethylene glycol as a solvent. With the independent variables of this research that PEG solvent flow rate of 100-500 cm3/min, the solvent concentration of 5-20%, and the number of membrane fibers, namely 1000, 3000, 5000.
In this study, the results obtained in the optimum solvent flow rate of 500 ml/min and the amount of fiber 5000, for the mass transfer coefficient (KL) of 3,7x10-4 cm/s, the efficiency of absorption (%R) at 14,6%, the flux (J) of 1,4x10-5 mol/cm2.s, and acid loading of 4x10-3. Whereas, the optimum solvent concentration is 0%.
"
Depok: Fakultas Teknik Universitas Indonesia, 2017
S66344
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muhammad Fauzan Ghasani
"Karbon dioksida diklasifikasikan sebagai senyawa fouling pada gas buang yang dapat mengurangi nilai panas dan memiliki karakteristik korosif pada pipa. Salah satu metode pemisahan CO2 dari gas buang adalah dengan menggunakan kontaktor membran. Penggunaan kontaktor membran super hidrofobik kadang-kadang sebagai media alternatif karena kemampuannya dalam memisahkan CO2 dengan bidang kontak besar dalam ukuran yang kompak dan memiliki ketahanan yang baik terhadap serangkaian tindakan terjadi karena penyerap. Tujuan dari penelitian ini adalah untuk menemukan ide tentang bagaimana super hidrofobik membran kinerja kontaktor dalam menyerap gas CO2. Gas yang digunakan dalam penelitian ini adalah campuran CO2 dan N2 sebagai perkiraan gas buang yang sebenarnya. Dalam penelitian ini, CO2 - campuran gas N2 dilewatkan pada bagian shell dan penyerap DEA 5% di bagian lumen kontaktor membran. Pengambilan sampel dilakukan setelah 15 menit dan isi dari CO2 yang tersisa - N2 dianalisis dengan kromatografi gas. Variasi dalam penelitian ini adalah laju alir pelarut DEA dan jumlah kontaktor membran serat. Tertinggi massa nilai transfer koefisien 3.86 x 10-4 cm / s, dan flux CO2 dari 8,84 x 10-6 mmol / cm2s dicapai dengan menggunakan 500 ml / menit dari DEA debit dan 1000 jumlah serat membran. Jumlah maksimum CO2 yang diserap adalah 1,328, dan persentase penyerapan 96,21% yang dicapai dengan menggunakan 500ml / min dari DEA debit dan 5000 jumlah serat membran.
Carbon dioxide is classified as a fouling compound on flue gasses that can reduce the heat values and has corrosive characteristic on piping. One of the method of CO2 separation from flue gases is by using membrane contactor. The use of super-hydrophobic membrane contactor is occasionally as alternative medium due to its ability in separating the CO2 with large contact area in a compact size and has a good resistance towards a series of action occurred due to absorbent. The objective from this research is to discover the idea of how super-hydrophobic membrane contactor performance in absorbing CO2 gas. The gas used in this study is a mixture of CO2 and N2 as an approximation of the actual flue gas. In this study, the CO2 - N2 gas mixture is passed at the shell part and absorbent DEA 5 % in the lumen part of the membrane contactor. Sampling was done after 15 minutes and the content of the remaining CO2 - N2 analyzed by gas chromatography. Variations in this research are the DEA solvent flow rate and total fiber membrane contactors. The highest mass transfer coefficient value is 3.86 x 10-4 cm/s, and CO2 flux of 8.84 x 10-6 mmol/cm2s are achieved by using 500 ml/min of DEA flowrate and 1000 amount of membrane fibres. The maximum amount of CO2 absorbed is 1.328, and absorption percentage of 96.21% are achieved by using 500mL/min of DEA flowrate and 5000 amount of membrane fibres."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S64684
UI - Skripsi Membership  Universitas Indonesia Library
cover
Angeline Paramitha
"Teknologi alternatif yang potensial untuk pemisahan CO2 dari gas alam adalah kontaktor membran. Teknologi tersebut terus dikembangkan sampai sekarang karena kontaktor membran memiliki kekurangan seperti selektivitas yang semakin lama semakin menurun. Pada kali ini, pemisahan CO2 dari gas alam akan dilakukan dengan pelarut fisika, yaitu PEG. Pemisahan gas dengan pelarut fisika dapat memberikan keuntungan, dapat menghasilkan selektivitas yang cukup tinggi terhadap CO2 serta lebih tidak korosif dibandingkan dengan pelarut kimia. Ada tiga buah jumlah serat membran yang digunakan, yaitu 1000, 3000, 5000. Laju alir pelarut divariasikan dari 100-500 cm3/s. Konsentrasi pelarut divariasikan dari 5-20 b/v. Laju alir gas yang digunakan tetap yaitu sebesar 305 mL/menit. Penelitian dilakukan pada tekanan dan temperatur ambien. Gas yang digunakan dalam penelitian ini adalah campuran gas sintetik CO2 dan CH4 dengan komposisi masing-masing 30 dan 70.
Berdasarkan penelitian, didapatkan jumlah CO2 terabsorpsi mencapai 1,07 x 10-5 mol/s dan efisiensi penyerapan mencapai 12,44 . Koefisien dan fluks perpindahan massa masing-masing mencapai 4,47 x 10-7 m/s dan 2,05 x 10-5 mol/m2.s, serta acid loading mencapai 1,3 x 10-2 mol CO2/mol PEG untuk variasi laju alir dan jumlah serat membran. Sedangkan untuk variasi konsentrasi, kondisi optimumnya adalah PEG 10 b/v.

Alternative technology for CO2 separation is a membrane contactor. This technology continuous to be developed untul now to overcome the weaknesses of the membran itself such as the selectivity progressively decreased as the time goes by. The present study will be done with a physical solvent, PEG. Gas separation with physical solvent provides benefits such as it can produce sufficiently high selectivity towards CO2 and less corrosive than the chemical solvents. There are 3 total membrane fiber that we used, 1000, 3000, and 5000. The solvent flow rate varied from 100 500 cm3 s. Solvent concentration varied from 5 20 wt. The gas flow rate used remains at 305 mL min. The study was conducted at ambient pressure and temperature. The gas used in this study is a synthetic gas mixture of CO2 and CH4 with the composition of their respective 30 and 70.
Based on research, it was obtained the amount of CO2 absorbed reached 1.07 x 10 5 mol s and absorption efficiency reached 12.44 . Mass transfer coefficient and flux respectively reached 4.47 x 10 7 m s and 2.05 x 10 5 mol m2.s, as well as acid loading of 1.3 x 10 2 mol CO2 mol PEG for the variation of solvent flow rate and total membrane fiber. Whereas for the concentration variation, the optimum condition was PEG 10 wt.
"
Depok: Fakultas Teknik Universitas Indonesia, 2017
S66498
UI - Skripsi Membership  Universitas Indonesia Library
cover
Juan
"[ABSTRAK
Tujuan dari pelaksanaan penelitian ini adalah untuk menguji performa penyerapan gas CO2 dengan menggunakan kontaktor membran superhidrofobik. Adapun variasi yang diuji pada penelitian ini adalah pengaruh laju alir gas CO2 (160, 240, dan 320 mL/menit) dan jumlah serat membran kontaktor (2000, 4000, dan 6000). Pada penelitian ini, didapatkan hasil yaitu peningkatan dari laju alir gas umpan menurunkan efisiensi dari proses, namun meningkatkan kapasitas penyerapan dan koefisien perpindahan massa secara menyeluruh. Pada peningkatan jumlah membran, terjadi peningkatan untuk nilai efisiensi, kapasitas penyerapan, dan koefisien perpindahan massa secara menyeluruh. Nilai efisiensi penyerapan tertinggi tercapai sebesar 29% pada laju alir gas umpan sebesar 160 mL/menit dan jumlah serat membran sebesar 6000. Nilai koefisien perpindahan massa dan kapasitas penyerapan tertinggi adalah 1,14x10-4 cm/s dan 0.045 mmol pada laju alir gas 320mL/menit dan jumlah serat membran sebesar 6000.
ABStRACT
The purpose of this experiment is to examine the performance of superhydrophobic contactor in the absorption of CO2 using water. The variation tested in this experiment is the CO2 gas flow rate (160, 240, 320 mL/min) and the number of fiber modules (2000, 4000, and 6000). The results obtained from this experiment is, the increasement of gas flow rate reduces the absorption efficiency, and increases the absorption capacity and the overall mass transfer coefficient. As the number of fibers increases, the efficiency, overall mass transfer coefficient, and absorption capacity also increases. The maximum value for efficiency is 29% and obtained for 160 mL/min gas flow rate and 6000 module fibers. The maximum value for overall mass transfer coefficient and absorption capacity are 1.14x10-4 cm/s and 0.045 mmol respectively for 320 mL/min gas flow rate and 6000 number module.;The purpose of this experiment is to examine the performance of superhydrophobic contactor in the absorption of CO2 using water. The variation tested in this experiment is the CO2 gas flow rate (160, 240, 320 mL/min) and the number of fiber modules (2000, 4000, and 6000). The results obtained from this experiment is, the increasement of gas flow rate reduces the absorption efficiency, and increases the absorption capacity and the overall mass transfer coefficient. As the number of fibers increases, the efficiency, overall mass transfer coefficient, and absorption capacity also increases. The maximum value for efficiency is 29% and obtained for 160 mL/min gas flow rate and 6000 module fibers. The maximum value for overall mass transfer coefficient and absorption capacity are 1.14x10-4 cm/s and 0.045 mmol respectively for 320 mL/min gas flow rate and 6000 number module., The purpose of this experiment is to examine the performance of superhydrophobic contactor in the absorption of CO2 using water. The variation tested in this experiment is the CO2 gas flow rate (160, 240, 320 mL/min) and the number of fiber modules (2000, 4000, and 6000). The results obtained from this experiment is, the increasement of gas flow rate reduces the absorption efficiency, and increases the absorption capacity and the overall mass transfer coefficient. As the number of fibers increases, the efficiency, overall mass transfer coefficient, and absorption capacity also increases. The maximum value for efficiency is 29% and obtained for 160 mL/min gas flow rate and 6000 module fibers. The maximum value for overall mass transfer coefficient and absorption capacity are 1.14x10-4 cm/s and 0.045 mmol respectively for 320 mL/min gas flow rate and 6000 number module.]"
2016: Fakultas Teknik Universitas Indonesia, 2016
S62296
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sherlyn Esther Ramaida
"Dalam studi ini, efektivitas penyerapan CO2 menggunakan kontaktor membran serat berongga dievaluasi berdasarkan variasi laju alir gas, variasi laju alir pelarut, dan alokasi cairan. Pada studi ini digunakan kontaktor membrane yang terdiri dari 50 serat PVC dan pelarut Triethanolamine. Laju alir gas yang digunakan adalah 0.1, 0.15 dan 0.2 L/min, sedangkan laju pelarut yang digunakan adalah 200, 250, 300, 350, dan 400 mL/min. Kemampuan penyerapan paling baik adalah ketika laju alir pelarut sebesar 400 mL/min, laju alir gas sebesar 0.2 L/min dan mengalirkan pelarut di dalam fiber.

In this study, the effectiveness of CO2 absorption through hollow fiber membrane contactor is evaluated based on the gas flow rate variation, solvent flow rate variation, and fluid allocations. The present stud involves a membrane contactor with 50 PVC fibers and Triethanolamine as solvent. Gas flow rate used was 0.1, 0.15 L and 0.2 L / min, while the rate of solvent used is 200, 250, 300, 350, and 400 mL / min. The absorption is at its best when the solvent flow rate is 400 mL/min, when gas flow rate is 0.2 L/min and by flowing the solvent inside the fiber."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S46603
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>