Hasil Pencarian

Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 131280 dokumen yang sesuai dengan query
cover
Ahmad Jahrudin
"ABSTRAK
Pemodelan Inversi 3D struktur bawah permukaan berdasarkan data anomali gaya berat dan dan 2D anomali magnetik dilakukan untuk mengidentifikasi keberadaan potensi hidrokarbon di daerah ldquo;X rdquo;, dimana pada daerah penelitian terdapat struktur up dome yang mengindikasikan beberapa kemungkinan, diantaranya intrusi batuan, carbonate bulid up dan juga mud diapir. Model inversi 3D data anomali gaya berat dan magnetik telah dikoreksi dengan 2 dua penampang seismik yang ada pada daerah penelitian. Model inversi 3D dilakuan pada data anomali residual pada model gaya berat dan 2D pada anomali magnetik. Hasil pemodelan inversi 3D data anomali gaya berat menunjukan bahwa puncak up dome berada pada kedalaman sekitar 800 meter dari permukaan daerah penelitian, hasil ini sesuai dengan analisis spektrum dan kedalaman pada penampang seismik, adapun nilai densitas dari tubuh up dome tersebut bernilai sekitar 2,78 g/cm3. Sedangkan pada anomali magnetik yang telah dilakukan, struktur tersebut mengindikasikan merupakan batuan intrusi dengan anomali suceptibilitas sekitar 7.4 SI, yang menunjukan batuan beku.

ABSTRACT
3D inversion modeling of subsurface based on gravity anomaly data and 2D magnetik anomaly data used for identifcation hydrocarbon potential in ldquo x rdquo . Where in the study area there are up dome structures that indicate some possibilities, including igneous rock intrusion, carbonate bulid up and also mud diapir. 3D inversion modeling of gravity and magnetic anomaly data correlated to two sesimic section which avilable in study location. 3D inversion model is performed on the residual anomaly data on the gravity model and 2D in the magnetic anomaly. The result of 3D inversion modeling of gravity anomaly data shows that the peak up dome is at a depth of about 800 meters from the surface of the research area, this result corresponds to spectrum analysis and depth on the seismic cross section, while the density value of the up dome body is approximately 2.78 g cm3. While on the magnetic anomaly that has been done, structure of the dome indicates an intrusion structure with suceptibility anomaly approximately 7.4 SI, show the structure of igneous rock."
Lengkap +
2018
T51598
UI - Tesis Membership  Universitas Indonesia Library
cover
Nur Najmiah Tullailah
"ABSTRAK
Area X, Cekungan Sumatera Utara merupakan target eksplorasi hidrokarbon dengan mengejar target lapisan dalam sebagai prospek baru. Metode seismik telah dilakukan namun hasilnya masih memiliki ambuigitas dalam menggambarkan bentuk bawah permukaan khususnya lapisan dalam di antaranya keberadaan basement sebagai dasar dari lapisan sedimen di atasnya yang menjadi target eksplorasi. Metode Gaya Berat dan Magnetotellurik dilakukan untuk mengkonfirmasi keberadaan basement yang menjadi dasar intrepretasi pada seismic. Metode Magnetotellurik dilakukan untuk menunjukkan distribusi nilai resistivitas litologi di bawah permukaan, dalam hal ini nilai resistivitas antara basement dan formasi lain di sekitarnya. Berdasarkan hasil inversi 2D dan 3D MT pada lintasan 4 dan 6 menunjukkan adanya kontras resistivitas yaitu zona resistivitas tinggi (Rho=102 - 103 ohm.m) pada bagian SW dari lintasan dan pada kedalaman 6000 meter kebawah yang mengindikasikan lapisan formasi yang lebih tua dan dalam hal ini juga diindikasikan sebagai basement , sedangkan di sebelah NE dari lintasan tersebut tampak litologi yang lebih konduktif (Rho= 1-101 ohm.m) dan berada
bagian atas dari lintasan yang menunjukkan lapisan formasi yang lebih mudah
diindikasikan sebagai lapisan sedimen. Metode Gaya Berat akan menunjukkan distribusi nilai densitas yang diperoleh dari hasil gravity forward modelling. Hasil dari metode gaya berat menunjukkan adanya kontras densitas di bagian sisi kiri dan kanan dari lapangan, dimana berdasarkan peta regional terdapat anomali nilai rendah berkisar 26-42 mGal dan anomaly tinggi berkisar 48-66 mGal. Hasil pemodelan gravity 2D pada lintasan 4 dan 6 menunjukkan keberadaan basement pra-tersier berada pada kedalaman 6000 m kebawah dengan beberapa formasi diatasnya yang terdiri dari formasi pratersier dan formasi yang terbentuk pada tersier. Formasi pada lapisan dalam yang
berpotensi sebagai reservoar yang baik adalah Formasi Tampur yang merupakan batu gamping serta Formasi Parapat yang merupakan batu pasir.

ABSTRACT
Area X, North Sumatra Basin is a target for hydrocarbon exploration by pursuing the inner layer target as a new prospect. Seismic methods have been carried out but the results still have ambiguity in describing subsurface forms, especially the inner layers, including the presence of basements as the base of the sediment layer above which is the target of exploration. The Gravity and Magnetotelluric methods are carried out to confirm the existence of the basement which is the basis of the interpretation of seismic. The Magnetotelluric method is performed to show the distribution of lithological
resistivity values below the surface, in this case the resistivity value between the basement and other formations around it. Based on the results of 2 D and 3D MT inversion on tracks 4 and 6, the contrast resistivity is high resistivity zone (Rho =Rho=102 - 103 ohm.m) on the SW portion of the track and at a depth of 6000 meters down which indicates the older formation layer and in this case also it is indicated as a basement, while in the NE from the track it appears more conductive lithology (Rho= 1-101 ohm.m) and is located at the top of the track which shows the formation layer which is more easily indicated as a sediment layer. The gravity method will show the distribution of density values obtained from the gravity forward modeling. The results of the gravity method show that there is contrast density on the left and right sides of the
field, where based on regional maps there are low value anomalies ranging from 26-42 mGal and high anomalies ranging from 48-66 mGal. The gravity 2D modeling results on tracks 4 and 6 show the existence of a pre-tertiary basement at a depth of 6000 m below with some formations above which consists of pre-tertiary formations and tertiary formation. Formations in the inner layer which have the potential as a good reservoir are the Tampur Formation which are limestone and Parapat Formation."
Lengkap +
2019
T51936
UI - Tesis Membership  Universitas Indonesia Library
cover
Cicilia Budi Saraswati
"ABSTRAK
Metode gravitasi merupakan metode geofisika yang didasarkan pada pengukuran variasi medan gravitasi karena adanya perbedaan rapat massa antar batuan. Oleh sebab itu, metode gravitasi sering digunakan dalam eksplorasi bawah permukaan, salah satunya eksplorasi hidrokarbon. Dalam proses awal, penentuan kedalaman basement dirasa penting supaya dapat dilanjutkan untuk melakukan reka ulang dalam menentukan zona reservoir hidrokarbon. Setelah penentuan basement selesai, dilanjutkan dengan melakukan permodelan inversi 3D supaya didapatkan gambaran detail mengenai struktur bawah permukaan yang mendekati bentuk sebenarnya. Berdasarkan hasil analisis data didapatkan kedalaman basement rata-rata sekitar 5.5 km dengan struktur pembentuknya adalah patahan naik dan arah strukturnya dari Timur Laut ke Barat Daya. Hasil model inversi 3D didapatkan basement yang terdeteksi merupakan batuan beku Andesite dengan nilai densitasnya sekitar 2.5 gr/cm3. Kemudian untuk zona reservoir hidrokarbon diperkirakan terletak di daerah central basin sampai bagian Selatan pulau Timor, dengan komposisi batuan reservoirnya adalah batuan sedimen pasir dengan nilai densitas sekitar 2.2 gr/cm3.

ABSTRACT
The method of gravity is a geophysical method which is based on the measurement of variation of the variative gravitational field due to the difference in mass density between rocks. Therefore, gravity methods are often used in subsurface exploration, one of which is hydrocarbon exploration. In the initial process, the determination of the basement depth is important in order to re establish the process in determining the hydrocarbon reservoir zone. After the basement determination is completed, the next step is to proceed with 3D inversion modeling in order to get a detailed picture of the subsurface structure that approximates the actual shape. Based on the data analysis, the average basement depth is about 5.5 km with its forming structure is the rising fracture and the direction of its structure from Northeast to Southwest. The result of 3D inversion model was found the detected basement is Andesite igneous rock with density value about 2.5 gr cm3. Then for the hydrocarbon reservoir zone is estimated to be located in the central basin area to the Southern part of the island of Timor, with the composition of the reservoir rock is sand sedimentary rock with a density value of about 2.2 gr cm3."
Lengkap +
2017
S69719
UI - Skripsi Membership  Universitas Indonesia Library
cover
Iskandar
"Lapangan geotermal X berada di area gunung A yangmana berdasarkan data geologi ditemukan adanya manifestasi berupa hot spring dan fumarole. Pengukuran MT dilakukan untuk mengetahui persebaran resistivity batuan di bawah permukaan. Pengolahan data MT dilakukan dari analisis time series dan filtering noise kemudian dilakukan Transformasi Fourier dan Robust Processing. Setelah itu baru dilakukan crosspower untuk menyeleksi data sehingga output dari proses ini berupa kurva MT. Setelah didapatkan kurva MT dilakukan koreksi statik dikarenakan kurva TE dan TM terjadi shifting. Untuk proses akhirnya baru dilakukan inversi 2D dan inversi 3D. setelah itu dilakukan perbandingan antara 2D dan 3D. Wilayah interest lapangan X berada di lintasan AA dan lintasan AB. Berdasarkan analisis 3D diidentifikasi bahwa zona alterasi menipis di wilayah upflow dan menebal ke arah outflow yangmana sesuai dengan teori. Wilayah upflow dapat diketahui dengan melihat manifestasi berupa fumarole.

The geothermal field X is located in the area of Mount A which based on geological data found the presence of hot spring and fumarole manifestations. MT measurements were carried out to determine the distribution of rock resistivity in the subsurface. MT data processing is starts from time series analysis and noise filtering then Fourier Transform and Robust Processing are performed. After that, crosspower is done to select data so that the output of this process is an MT curve. After got the MT curve then a static correction is done because the TE and TM curves are shifting. For the final process are 2D inversion and 3D inversion. After that make a comparison between 2D and 3D. The area of interest in field X is on the line AA and line AB. Based on the 3D analysis, it was identified that alteration zones thinned in the upflow region and thickened towards the outflow which is make sense with the theory."
Lengkap +
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sibarani, Catherine
"Salah satu metode geofisika yang dapat digunakan untuk eksplorasi panas bumi adalah metode gravitasi karena metode ini dapat mendeteksi batuan dibawah permukaan berdasarkan variasi medan gravitasi yang disebabkan oleh perbedaan densitas batuan. Dalam sistem panas bumi, salah satu objek yang sensitif terhadap kontras densitas adalah batuan reservoir. Oleh sebab itu, metode gravitasi sangat tepat digunakan untuk mengidentifikasi batuan reservoir. Batuan reservoir memiliki densitas batuan yang relatif rendah akibat efek pemanasan dari heat source, sedangkan batuan non-reservoir disekitarnya memiliki densitas batuan yang lebih tinggi. Kontak antara kedua batuan inilah yang akan dideteksi oleh metode gravitasi dan selanjutnya dimodelkan dengan metode inversi dalam 3D.
Metode inversi dilakukan karena bersifat lebih objektif dan sesuai dengan keadaan asli dilapangan dibandingkan dengan pemodelan forward. Pemodelan juga dilakukan dalam 3D untuk memberikan gambaran yang lebih jelas tentang batuan dibawah permukaan, tidak hanya dari satu penampang saja. Sebagai justifikasi letak batuan reservoir, dilakukan analisis patahan menggunakan analisis derivatif berupa First Horizontal Derivatives FHD dan Second Vertical Derivatives SVD . Identifikasi patahan ini akan membantu menganalisis keberadaan dan bentuk batuan reservoir karena patahan berperan penting sebagai zona recharge dan discharge yang mengarah menuju atau keluar dari batuan reservoir.

One of many geophysical methods that can be used for geothermal exploration is gravity method because this method is able to detect subsurface rocks based on the variation of gravity field that is caused by the difference of rock density. In geothermal system, one of the object that is sensitive to density contrast is reservoir rock Therefore, gravity method is the appropriate method used to identify geothermal reservoir. Reservoir rock has a relatively low density as a heating efect from heat source, while non reservoir rock has higher density. The contact between these rocks will be detected with gravity method and further will be modeled with inversion method in 3D.
Inversion method is applied because it is more objective and suitable with the real condition rather than forward method. Modeling is also done in 3D to give a better representation on subsurface area, not only from one section. To justify the location of reservoir rock, subsurface structure analysis using derivatives analysis which are First Horizontal Derivatives FHD and Second Vertical Derivatives SVD is done. Structure identification will help analyzing reservoir whereabouts and its form because subsurface structure has an important role as recharge and discharge zone of the geothermal system that aim towards and leave the reservoir rock.
"
Lengkap +
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2017
S67351
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nela Indra Sari
"Telah dilakukan identifikasi zona mineralisasi emas pada lapangan ldquo;GB rdquo; dengan menggunakan inversi 3D data magnetik. Lapangan ldquo;GB rdquo; merupakan daerah prospek mineral emas yang terletak di provinsi Jambi, Indonesia. Tipe mineralisasi pada lapangan tersebut berupa Epitermal Sulfidasi Tinggi dan porfiri Cu-Au yang telah terbentuk pada lingkungan hidrotermal. Karakteristik batuan ini adalah batuan intrusi intermediet asam sebagai batuan induknya. Batuan ini mengandung mineral bijih utama berbentuk tembaga dan emas serta mineral pengikut lainnnya yang bersifat magnetik. Oleh karena itu, metode magnetik sangat sensitif untuk mengidentifikasi daerah prospek mineralisasi emas. Pada penelitian ini akuisisi dilakukan dengan jarak 5 m antar titik stasiun yang terdiri dari 51 lintasan dengan jarak antar lintasan 100 m dan total panjang lintasan 16,5 kilometer. Identifikasi posisi, jenis serta kedalaman struktur bawah permukaan yang berhubungan dengan zona pembentukan emas diatas, dilakukan analisis derivatif dari perhitungan first horizontal derivative dan dekonvolusi Euler. Selanjutnya dilakukan pemodelan inversi dalam 3D untuk mengetahui gambaran yang lebih objektif dari tubuh batuan bawah permukaan. Dalam penelitian ini, data IP induced polarization digunakan untuk memverifikasi hasil data magnetik dengan melihat parameter resistivity dan chargeability zona prospek. Begitu juga dengan data geologi yang digunakan untuk mengetahui sebaran batuan yang menjadi lingkungan pengendapan emas. Hasil akhir penelitian ini teridentifikasi zona mineralisasi emas berada berupa lithocap dan body intrusi dengan perkiraan top body berada pada kedalaman 80 m dari permukaan topografi.

Identification of gold mineralization zone in ldquo GB rdquo field had been done using 3D Inversion magnetic data. ldquo GB rdquo field is a gold mineral prospect field, located in Jambi province, Indonesia. Mineralization type of this area are high epithermal sulphidation and porphyry Cu Au that have been formed in hydrothermal environment. The characteristic of this type is intermediate acid igneous rock as the host rock. This rock consist of mineral ores such as copper gold and magnetic gangue minerals. Therefore, magnetic method is very sensitive to identify gold mineral prospect zone. In this research, magnetic data was acquired by 5 m spacing between each station, that are consist of 51 lines with 100 m space between lines and the total length of lines is 16.5 kilometer. Identifying position, types and depth of subsurface structure relating to gold deposition environment, derivative analysis is done with first horizontal derivative and euler deconvolution calculation. Then, we make 3D inversion model, to delineate the subsurface structure objectively. In this research, induced polarization data is used to see resistivity and chargeability parameter of the prospect zone and also geological data to find out distribution of rock that associated with gold deposition environment. The result of this research, gold deposition zone is identified by lithocap and intrusion body with top of instruction rock at depth 80 m from the surface."
Lengkap +
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2017
S67506
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ilma Afrilia Riska
"Di alam, emas berasal dari larutan hidrotermal dan diendapkan dalam bentuk endapan epitermal. Struktur berupa patahan berperan penting dalam proses pengendapan mineral emas karena merupakan jalan mengalirnya larutan hidrotermal menuju permukaan. Salah satu metode eksplorasi emas adalah metode gravitasi. Metode ini mengidentifikasi zona mineralisasi emas dari struktur patahan yang ada di daerah penelitian. Pemodelan inversi 3D merupakan salah satu metode dalam gravitasi yang dapat memberi informasi yang jelas pada target survey. Pemodelan tersebut dianggap lebih realistis karena bentuk model geometri dapat disesuaikan dengan bentuk benda sebenarnya di alam dan perhitungannya pun lebih akurat. Penelitian dilakukan berdasarkan hasil survey gravitasi Pongkor yang telah dilakukan oleh PT Antam Tbk. Endapan hidrotermal Pongkor termasuk ke dalam tipe endapan sulfidasi rendah. Pada tipe endapan epitermal sulfidasi rendah, emas diendapkan dalam urat-urat vein yang berasosiasi dengan patahan. Pengolahan data dilakukan dengan analisis derivative, analisis spektrum, dan pemodelan inversi 3D gravitasi. Berdasarkan hasil survey dan olah data, tampak bahwa zona mineralisasi emas berada pada bagian tengah daerah penelitian yang ditandai dengan anomali gravitasi yang tinggi pada struktur patahan. Patahan yang terdeteksi pada zona potensi mineralisasi emas adalah sebanyak 8 patahan. Dari hasil inversi 3D, zona mineralisasi emas tersebut memiliki densitas sebesar 2,8-3,34 g/cc.

In nature, gold are originated from hydrothermal liquid and deposited in epithermal deposit form. Structures such as faults have important role in the process of gold deposition since it is become the hydrothermal flow path to the surface. One of the method that can be used to do gold exploration is gravity method. This method identify the gold mineralization zone from faults on the research region. 3D inversion modeling is one of geophysics method that can give clear information on the target. The modeling can be said more realistic since the geometry model can be fitted with the real condition in nature and the measurement be more accurate. The research is done based on gravity survey result by PT Antam Tbk. Pongkor hydrothermal deposit categorized as epithermal low sulphidation. The processing data is done by do derivative analysis, spectrum analysis, and 3D gravity inversion modeling. Based on the survey result and processing data, gold mineralization zone are at the middle of research region that have high gravity anomaly at the faults. There are eight faults detected at the gold mineralization potential zone. From 3D inversion result, density of the gold mineralization zone is 2,74 3,34 g cc. "
Lengkap +
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2017
S67159
UI - Skripsi Membership  Universitas Indonesia Library
cover
Amanda Tasya Deborah
"Daerah penelitian terletak di Sunda Basin yang merupakan bagian dari Cekungan Northwest Java yang terletak di offshore. Cekungan ini terbukti produktif, namun aktivitas eksplorasi saat ini di daerah penelitian ini jarang. Penelitian difokuskan pada reservoir hidrokarbon dari formasi karbonat di Lapangan 'X', yang dikenal sebagai Formasi Batu Raja Atas. Lapangan ini memiliki dua sumur untuk diteliti, yaitu Sumur GD1 dan GD2, keduanya merupakan sumur deviasional dan memiliki jarak yang berdekatan satu sama lain. Dalam menentukan reservoir hidrokarbon di daerah ini, analisis petrofisika dan metode inversi seismik telah dilakukan. Keduanya akan digunakan untuk menganalisis reservoir hidrokarbon sebagai hasil utama. Parameter analisis petrofisika terdiri dari permeabilitas, densitas, volume shale, porositas dan saturasi air. Selain itu, inversi seismik menerapkan metode impedansi akustik untuk menunjukkan kenampakan geologi di bawah permukaan, sehingga dapat mengidentifikasi karakterisasi reservoir. Nilai Impedansi Akustik menunjukkan bahwa zona minat di Batu Raja Atas atau diperpendek formasi UBR memiliki rentang interval dari 17.000 hingga 22.000 (ft/s)*(g/cc), sehingga kedua metode tersebut dapat membuktikan formasi ini memiliki karakterisasi yang baik sebagai target utama atau reservoir. Berdsarkan analisis petrofisika, hasil perhitungan parameter volume shale, saturasi air, dan porositas yang telah dianalisis menunjukkan bahwa area zone of interest memiliki reservoir hidrokarbon yang cukup baik. Hal tersebut dapat dilihat dari nilai rata-rata volumei shalei sebesari kurang dari sama dengan 40%, nilaii saturasii airi sebesari kurang dari sama dengan 0.43 v/v, dan nilaii porositasi sebesari 0.117-0.13 v/v.

The study area is located in Sunda Basin which is part of Northwest Java Basin that lies on offshore. The basin is proven to be prolific, however, the current exploration activity in this study area is sparse. The study is focused on the hydrocarbon reservoir of the carbonate formation, which is known as Upper Batu Raja Formation. This research has two wells to be researched, which are Well GD1 and GD2, both of them are deviational wells and have close distance with each other. To specifically determine the hydrocarbon reservoir in this area, a petrophysical analysis and seismic inversion method have been carried out. Both of them will be used to analyze the hydrocarbon reservoir as the main result. The parameters of petrophysical analysis consist of permeability, density, shale volume, porosity and water saturation. Aside from that, the seismic inversion applies acoustic impedance method to show the geological appearance in the subsurface, therefore it can identify the reservoir characterization. The Acoustic Impedance value shows that the zone of interest in Upper Batu Raja or as shorten as UBR formation has interval range from 17000 to 22000 (ft/s)*(g/cc), hence, these methods promptly prove this formation has good characterization as the main target or reservoir. According to petrophysical analysis, the results of shale volume, water saturation, and porosity which have been analyzed show that zone of interest has a good hydrocarbon reservoir. It has been proved from the average calculation of shale volume more or less 40%, water saturation more or less 0.43 v/v, and porosity in range 0.117-0.13 v/v."
Lengkap +
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2023
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ferina Nugrahitasari
"Telah dilakukan penelitian geofisika dengan metoda magnetik di Sorolangun, Jambi, Sumatra. Penelitian ini bertujuan untuk mengindetifikasi zona mineralisasi emas sistem porfiri berdasarkan hasil pemodelan magnetik 3D. Pengambilan data dilakukan dengan menggunakan Proton Precession Magnetometer (PPM) dan Global Positioning System (GPS). Luas area 2000 meter x 2000 meter dengan spasi antar titik 5 meter. Pengolahan data mentah dilakukan dengan koreksi diurnal (koreksi variasi harian) dan IGRF (international geomagnetics Refrence Field) untuk mendapatkan medan anomali lokal. Kontinuasi keatas dilakukan pada ketinggian 50 meter. Turunan kedua vertikal (SVD) digunakan untuk menentukan jenis struktur pada wilayah penelitian agar mempermudah proses interpretasi.
Penggunaan Reduksi ke kutub dilakukan untuk menyederhanakan proses interpretasi, namun karena wilayah penelitian berada di ekuator maka pengaplikasian RTP ini tidak maksimal, sebagai penggantinya digunakan Sinyal Analitik untuk mempermudah penentuan letak dari tubuh anomalinya. Interpretasi kualitatif dilakukan dengan menganalisis peta anomali medan magnetik total yang telah dikontinuasi dan diturunkan dua kali secara vertical. Hasil ini dikorelasikan dengan hasil pemodelan metoda magnetik 3D dan data IP.

A geophysical studies have been conducted with the magnetic method in Sorolangun, Jambi, Sumatra. This study aims to identify the zones of gold mineralization porphyry system based on 3D magnetic modeling results. Data were collected by using a Proton Precession Magnetometer (PPM) and Global Positioning System (GPS). The area of 2000 meters x 2000 meters with a space between a point 5 meters. Raw data processing is done with diurnal correction (correction of daily variation) and IGRF (International Geomagnetics Refrence Field) to get a local anomaly field. Upward Continuation performed at a height of 50 meters. The second vertical derivative (SVD) is used to determine the type of structure in the study area in order to facilitate the process of interpretation.
Reduction to the poles conducted to simplify the process of interpretation, however, because the study area is located at the equator then the application of RTP is not optimal, as the successor of Analytical Signal used to facilitate the determination of the location of the body anomalies. Qualitative interpretation is done by analyzing the total magnetic field anomaly maps that have been in continuation and lowered vertically twice. These results will be correlated with the results of the 3D magnetic modeling methods and data IP.
"
Lengkap +
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2013
S46364
UI - Skripsi Membership  Universitas Indonesia Library
cover
Liana Christy
"ABSTRAK
Lapangan ?X? terletak di Cekungan Sumatera Selatan tepatnya pada Formasi Talang Akar. Telah teridentifikasi sebelumnya bahwa pada lapangan ini tersaturasi hidrokarbon berupa condensate dan minyak. Zona target berupa paket-paket reservoir karena sistem pengendapannya berada pada lingkungan delta. Inversi simultan akan menghasilkan impedansi P, impedansi S, dan densitas. Dengan menggunakan parameter Zp, Zs, dan densitas, dapat diketahui persebaran zona hidrokarbon secara lateral. Impedansi P sensitif terhadap identifikasi hidrokarbon dikarenakan mengandung komponen inkompresibilitas. Sementara parameter impedansi S digunakan untuk identifikasi litologi karena mengandung komponen rigiditas yang sensitif terhadap matriks batuan. Untuk mengontrol inversi seismik, digunakan informasi dari log sumur. Analisis krosplot dari parameter fisis sumur dilakukan guna mengetahui anomali persebaran data. Anomali ini biasanya menandakan zona hidrokarbon. Hasil penelitian ini menunjukkan bahwa persebaran litologi dan zona hidrokarbon teridentifikasi dengan cukup baik dengan parameter Zp, Zs dan densitas.

ABSTRACT
Field "X" is located in the South Sumatra Basin precisely in Talang Akar Formation. Have been identified earlier that the field is saturated by hydrocarbons in the form of condensate and oil. Target zone in the form are packets of reservoir because the deposition system on this field are in the delta environment.Simultaneous inversion will generate impedance P, S impedance, and density. By using the parameter Zp, Zs and density, hydrocarbon zone can be seen spread laterally. Impedance P sensitive to the identification of hydrocarbon-containing due components of incompresibility . While the S impedance parameter is used to identify lithology because it contains components of rigidity that are sensitive to matrix of rock. In addition, information from well logs are used to control the seismic inversion. Crossplot analysis of the physical parameters of the wells was conducted to determine the distribution of data anomalies. This anomaly usually indicates a hydrocarbon zone.The results showed that the distribution of lithology and hydrocarbon zones identified quite well with Zp, Zs, and density.
"
Lengkap +
2015
S60200
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>