Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 134829 dokumen yang sesuai dengan query
cover
Moch Ardi Dimastiar
"Salah satu jenis material yang dewasa ini cukup populer dan berkembang adalah material komposit polimer berpenguat serat gelas (Glass Fiber Reinforced Polymer - GFRP), hal ini dikarenakan nilai ekonomis serta sifat mekanik yang baik yang mampu dihasilkan oleh material komposit tersebut. Ada banyak faktor yang dapat mempengaruhi sifat/ karakteristik material komposit GFRP, diantaranya adalah arah orientasi serat gelas serta perlakuan panas.
Penelitian ini membahas mengenai pengaruh orientasi serat gelas woven dan durasi perlakuan panas terhadap sifat/ karakteristik material komposit GFRP. Komposit GFRP yang diorientasikan arah seratnya dimanufaktur dengan menggunakan metode hand lay-up. Spesimen komposit GFRP selanjutnya dikenakan perlakuan panas dan dilakukan pengujian berupa pengujian tarik, tekuk, dan impak, serta dilakukan pengamatan tampilan perpatahan terhadap spesimen uji tarik yang memiliki nilai pengujian tertinggi dan terendah.
Dari hasil penelitian yang dilakukan, diperoleh kesimpulan bahwa orientasi serat gelas woven berpengaruh signifikan terhadap sifat tarik dan impak material dan berpengaruh kurang signifikan terhadap sifat tekuk komposit GFRP. Orientasi serat [00 or 900]s pada material komposit GFRP menghasilkan nilai karakteristik tertinggi bila dibandingkan dengan orientasi serat [00 or 900] / [450] dan 450]s. Sedangkan durasi perlakuan panas, tidak memberikan pengaruh terhadap sifat tarik, tekuk, dan impak dari material komposit GFRP.

One type of materials that is currently quite popular and evolve is a glass fiber reinforced polymer composite material (GFRP). This is due to the economic value and good mechanical properties that can be produced by the composite material. There are many factors that can affect the nature/ characteristics of GFRP composite materials, including the orientation of glass fiber and heat treatment.
This study discusses the influence of woven glass fiber orientation and the duration of heat treatment on the properties/ characteristics of GFRP composite materials. The fiber-oriented GFRP composites were manufactured using the hand lay-up method. GFRP composite specimens subsequently subjected to heat treatment and carried out tests in the form of tensile, bending, impact, and also observation of fracture appearance of tensile test specimens which had the highest and lowest test values.
From the results of the research conducted, it was concluded that the orientation of woven glass fibers had a significant effect on the tensile and impact properties of the material and had a less significant effect on the bending properties of the GFRP composite. The fiber orientation of [00 or 900]s in the GFRP composite material produces the highest characteristic values when compared to the fiber orientation [00 or 900] / [450] and [450]s. While the duration of heat treatment does not affect the tensile, bending and impact properties of the GFRP composite material.
"
Depok: Fakultas Teknik Universitas Indonesia, 2019
T52380
UI - Tesis Membership  Universitas Indonesia Library
cover
Andre Yosi
"Dewasa ini, penggunaan material komposit polimer berpenguat serat karbon (carbon fiber reinforced polymer, CFRP) dalam berbagai bidang semakin populer dan berkembang. Hal ini dikarenakan nilai ekonomis serta sifat mekanik yang baik yang mampu dihasilkan oleh material komposit tersebut. Ada banyak faktor yang dapat mempengaruhi sifat/ karakteristik material komposit CFRP, diantaranya adalah arah orientasi serat karbon serta perlakuan panas. Penelitian ini membahas mengenai pengaruh orientasi serat anyam karbon dan temperatur perlakuan panas terhadap sifat mekanik material komposit laminate bermatrik polimer. Komposit CFRP dimanufaktur dengan menggunakan metode hand lay-up dengan variasi orientasi [00 or 900]s, [00 or 900]/[±450] dan [±450]s. Spesimen komposit selanjutnya dilakukan pemanasan pada variasi temperatur lalu dilakukan pengujian berupa pengujian tarik, tekuk, impak, dan FTIR. Kekuatan tarik tertinggi diperoleh pada orientasi [0o or 90o]s dengan pemanasan 200 oC selama 3 jam, kekuatan tekuk tertinggi diperoleh pada orientasi [0o or 90o]s dengan pemanasan 100 oC selama 3 jam, serta energi impak tertinggi diperoleh pada orientasi [0o or 90o]s dengan pemanasan 100 oC selama 3 jam. Hasil pengujian FTIR menunujukkan gugus fungsi polimer yang dihasilkan dari Unsaturated Polyester Resin setelah pemanasan pada temperature curing adalah ikatan C=O (ester) dan ikatan ikatan C=C (cincin aromatik).

Nowadays, the use of carbon fiber reinforced polymer (CFRP) composite in various fields is getting more popular and fast growing. This is due to the economic value and good mechanical properties of the composite materials can produce. There are many factors that affect the characteristics of CFRP composite materials, including orientation of the carbon fiber and heat treatment. This study discusses the effect of the orientation of carbon woven fibers and the temperature of heat treatment on the mechanical properties of polymer matrix composite laminates. CFRP composites were manufactured using the hand lay-up method with various orientations [0 or 90o]s, [0 or 90o] / [± 45o] and [± 45o]s. The composite specimens were then heating at various temperatures. Characteristics of the composites were examined in the form of tensile test, bending test, impact test and FTIR analysis. The highest tensile strength was obtained at orientation [0o or 90o]s followed by heating at 200 oC for 3 hours. The highest bending strength was obtained at orientation [0o or 90o]s followed by heating at 100 oC for 3 hours, whereas the highest impact energy was obtained at orientation [0o or 90o]s followed by heating at 100 oC for 3 hours. FTIR test showed that the polymer functional groups from unsaturated polyester resin after heating at curing temperature are C=O bonds (ester) and C=C bonds (aromatic rings)."
Depok: Fakultas Teknik Universitas Indonesia, 2021
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Dena Prestia Hallatu
"Sifat mampu basah komposit merupakan salah satu kunci utama dalam peningkatan sifat mekanis komposit. Penelitian ini dilakukan untuk mengetahui pengaruh variasi orientasi, kerapatan dan perlakuan permukaan pada serat terhadap sifat mampu basah komposit. Serat yang digunakan adalah fiberglass dan pengukuran sudut kontak dilakukan dengan metode image processing. Hasil pengaruh dari variasi didapatkan dari hubungan variasi terhadap sudut kontak dan waktu pembasahan. Berdasarkan penelitian yang telah dilakukan, orientasi serat 45°/45° menghasilkan sudut kontak yang lebih rendah, namun membutuhkan waktu pembasahan yang lebih lama dibandingkan dengan orientasi serat 0°/90°. Perbedaan sudut kontak mencapai 6 derajat lebih rendah dan waktu pembasahan 20 detik lebih lama pada orientasi serat 45°/45°. Sedangkan untuk pengaruh kerapatan, kerapatan serat 900 menghasilkan sudut kontak yang lebih rendah dan waktu pembasahan yang lebih cepat dibandingkan dengan kerapatan serat 1250. Perbedaan sudut kontak mencapai 5 derajat lebih rendah dan waktu pembasahan hanya 7 detik lebih cepat. Adanya perlakuan permukaan berupa perendaman dengan NaOH 5% mampu menurunkan sudut kontak hinga 25 derajat untuk resin epoksi dan 3 derajat untuk resin poliester tak jenuh serta mempercepat waktu pembasahan 10 detik. Dengan menggunakan resin poliester tak jenuh, sudut kontak yang dihasilkan lebih kecil dan waktu pembasahan yang lebih cepat dibandingkan dengan resin epoksi.

Wettability of composite is one of key to increase mechanical properties of composite. This research focused on the effect of orientation, density and surface treatment on fiber to the characteristic of composite?s wettability. The fiber used in this research is fiberglass and the method for contact angle measurement is image processing. The result for those variations can be obtained from contact angle and wetting time. According to result, fiber with orientation 45°/45° gives lower contact angle but longer wetting time than fiber with orientation 0°/90°. For orientation 45°/45°, the differences in contact angle reaches 6 degree lower and the wetting time is 20 second longer. In case of fiber density, the sheet with 900 of fiber density 900 has lower contact angle and faster wetting time than the sheet with 1250 of fiber density. The sheet with 900 of fiber density has results that 5 degree lower for contact angle and 7 second faster for wetting time. The surface treatment with NaOH 5% can decrease the contact angle until 25 degree for epoxy resin used and 3 degree for unsaturated polyester used, also accelerate the wetting time until 10 second. The use of unsaturated polyester results smaller contact angle and faster wetting time than using epoxy resin."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S65417
UI - Skripsi Membership  Universitas Indonesia Library
cover
Akhmad Herman Yuwono
Fakultas Teknik Universitas Indonesia, 2001
LP-pdf
UI - Laporan Penelitian  Universitas Indonesia Library
cover
Nuha Dhia Fajri
"Penggunaan serat alam dapat menjadi alternatif penguat pada material komposit. Serat bambu merupakan salah satu serat alam yang dapat dijadikan penguat. Penelitian ini bertujuan untuk menentukan kekuatan tarik dan lengkung dari komposit Polyester/ Serat Bambu Haur Hejo yang memenuhi syarat SNI 01-4449-2006 untuk papan serat. Proses alkalisasi menggunakan larutan NaOH dilakukan pada bambu Haur Hejo. Fabrikasi komposit dilakukan dengan metode laminasi basah dengan variasi fraksi berat bambu Haur Hejo sbesar 10 wt%, 20 wt%, dan 30 wt%. Uji tarik, uji lengkung, dan densitas dilakukan pada papan komposit, serta dilakukan pengamatan pada permukaan papan komposit sebelum dan sesudah pengujian.
Komposit Polyester/Serat Bambu Haur Hejo 20 wt% memiliki nilai modulus tarik tertinggi yaitu (377,9 ± 38,7) MPa, nilai ini 66,05% lebih tinggi dari nilai modulus tarik Polyester. Nilai modulus lengkung tertinggi terdapat pada komposit Polyester/Serat Bambu Haur Hejo 30 wt% sebesar (3128,9 ± 341,5) MPa. Semua Komposit yang dihasilkan termasuk dalam kategori Papan Serat Kerapatan Tinggi mengacu pada standar SNI 01-4449-2006 dengan densitas komposit > 0,84 g/cm3. Hasil pengamatan morfologi komposit memperlihatkan adanya void, yang mungkin menyebabkan penurunan modulus dan kuat tarik untuk komposit dengan fraksi berat lebih dari 10 wt%.

The use of natural fibers can be an alternative reinforcement in composite materials. Bamboo fiber is one of the natural fibers that can be used as reinforcement. This study aims to determine the tensile and flexural strength of Haur Hejo bamboo fiber/polyester that meets the requirements of SNI 01-4449-2006 for fiberboard. The alkalization process using NaOH solution was carried out on Haur Hejo bamboo. Composite fabrication was carried out by wet lamination method with a variation of Haur Hejo bamboo weight fraction of 10 wt%, 20 wt%, and 30 wt%. Tensile test, bending test, and density were carried out on composite, and observations were made on the composite surface before and after testing.
Haur Hejo Bamboo Fiber / Polyester Composite 20 wt% has the highest modulus of tensile value (377.9 ± 38.7) MPa, this value is 66.05% higher than Polyester tensile modulus. The highest flexural modulus is found in Haur Hejo Bamboo Fiber/Polyester Composite 30% wt% composite at (3128.9 ± 341.5) MPa. All Composites produced are included in the category of High Density Fiber Board referring to SNI 01-4449-2006 standard with composite density> 0.84 g/cm3. Composite morphology observations show voids, which might cause a decrease in modulus and tensile strength for composites with a weight fraction of more than 10 wt%.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rifqi Hadyan Pandyashani
"Komposit sandwich merupakan material yang mempunyai potensi tinggi dalam aplikasi rancang bangun struktur ringan karena memiliki perbandingan strength to weight yang tinggi. Penelitian ini dilakukan untuk mencari sifat mekanik dari komposit sandwich dengan kulit kombinasi serat woven S-glass dan epoxy dan inti dari polyurethane foam. Material dibuat menjadi dua jenis orientasi S-glass yang berbeda yaitu 0°/90°/PU/0°/90 dan 0°/90°/PU/-45°/+45°. Material dibuat dengan menggunakan metode hand lay up dan vacuum bagging. Uji mekanik yang dilakukan adalah uji tekuk dan uji tekan arah edgewise. Penelitian ini memberikan hasil bahwa komposit sandwich jenis 0°/90°/PU/0°/90 memiliki sifat mekanik yang lebih baik dibandingkan dengan jenis 0°/90°/PU/-45°/+45°, dengan nilai kekuatan geser inti (74,38 ± 3,55) kPa, nilai kekuatan tekuk (1,22 ± 0,02) MPa, dan nilai kekuatan tekan (222,96 ± 8,98) kPa, serta kerusakan patahan pada citra SEM.

Sandwich composite is a material with high potential in light weight structure because of high strength to weight ratio. Research was done to find the mechanical properties of sandwich composite with S-glass and epoxy combination skin and polyurethane foam core. The sample is divided into two different S-glass orientation, 0°/90°/PU/0°/90 and 0°/90°/PU/-45°/+45°. The sample was made by hand lay up and vacuum bagging method. Flexural test and edgewise compressive test were used to determine the mechanical properties of the sample. From the result of the mechanical test, we know that sandwich composite 0°/90°/PU/0°/90 has a better mechanical properties than 0°/90°/PU/-45°/+45°, with (74,38 ± 3,55) kPa core shear stress, (1,22 ± 0,02) MPa facing bending stress, and (222,96 ± 8,98) kPa facing compressive stress, also with a fracture in SEM image."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2015
S60039
UI - Skripsi Membership  Universitas Indonesia Library
cover
cover
Fakultas Teknik Universitas Indonesia, 1998
S40945
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muhammad Fikri Fadila
"ABSTRAK
Indonesia merupakan negara kepulauan terbesar di dunia. Menurut data yang dikeluarkan oleh Kementerian Kelautan dan Perikanan, Indonesia memiliki pulau sekitar 17,499 pulau dari Sabang sampai Merauke. Mengetahui fakta ini maka banyak sektor industri (seperti energi, pariwisata, militer, dan perikanan) yang menggunakan moda transportasi lau sebagai saran pendukung bisnis industri mereka. Mengetahui hal ini maka perlu dilakukan suatu rancangan kapal yang memenuhi standar keselamatan operasi kapal. Salah satu aspek dalam merancang kapal yang menjadi perhatian penting terkait memenuhi standar tersebut adalah kekuatan dan konstruksi. Pada aspek kekuatan dan konstruksi terdapat pemilihan material guna mencapai standar keselamatan operasi kapal. Saat ini, baja merupakan material yang umum digunakan pada pembuatan kapal. Hal ini disebabkan oleh karakteristik mekanik baja yang dapat memenuhi standar operasi keselamatan kapal. Namun demikian, baja memiliki kekurangan yaitu massa jenis yang tinggi sehingga perlu dilakukan penelitian lebih lanjut terkait material alternatif yang memiliki karakteristik mekanik sama dengan baja namun massa jenisnya lebih rendah. Oleh karena itu, penelitian ini bertujuan untuk melakukan studi terkait material alternatif pembuatan kapal selain baja. Jenis komposit yang digunakan pada penelitian ini adalah epoksi-karbon dengan variabel konfigurasi serat (UD & woven) dan proses perlakuan (prepreg & wet). Metode yang digunakan pada penelitian ini adalah metode elemen hingga dengan menggunakan perangkat lunak ANSYS Academic R19.2 Student Version. Pengaturan yang diperlukan dalam melakukan metode elemen hingga diantaranya : Membuat desain model elemen hingga (meliputi geometri dan input jenis material), menentukan boundary conditions dan loading conditions. Kemudian, dilakukan analisis yang keluarannya berupa kurva load-displacement, kontur deformasi, dan yield strength.

ABSTRACT
Indonesia is the biggest archipelago country in the world. According to data released by Minister of Maritime and Fisheries, Indonesia has an island of around 17,499 islands from Sabang to Merauke. Knowing this fact, many industrial sectors (such as energy, tourism, military, and fisheries) use transportation modes as a suggestion to support their industrial business. Knowing this matter, it is necessary to do a ship design that meets the ships operating safety standards. One aspect of ship design which is an important concern regarding to this standard is construction and strength. On the aspect of construction and strength, material selection is one to be determined to achieved the operating safety standard. At present, steel is a material commonly used in shipbuilding due to its mechanical characteristic that can meet ship safety operating standard. However, steel has disadvantage of higher density. Further researh is needed regarding alternative materials that have the same mechanical characteristic as steel but lower density. Therefore, this study amis to conduct studies for alternative materials for shipbuilding other than steel. The type of composite used in this study is epoxy-carbon with variable fibre configuration (UD & Woven) and machining process (Prepreg & Wet). The method used in this study is using finite element method by ANSYS Academic R19.2 Student Version. Arrangements needed for use this method, such as : Design a finite element model (containing geometry and input type material), determine boundary conditions and loading conditions. Then, the analysis carried out in the form of load-displacement curves, contour deformation, and yield strength."
2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Surya Jaya
"ABSTRAK
Bahan penyerap radar atau Radar Absorbent Material adalah salah satu material maju untuk keperluan teknologi siluman. Penambahan sejumlah kecil clay terhadap komposit Epoksi/E-Glass telah terbukti dapat membuat bahan penyerap gelombang elektromagnetik lebihbaik dibandingkan bahan komposit Epoksi/E-glass. Penelitian ini, yang merupakan kelanjutan dari penelitian sebelumnya mengenai penyerapan gelombang elektromagnetik, bertujuan mempelajari sifat tarik, sifat tekuk, dan permukaan patahan komposit Epoksi/E-glass/Clay.. Empat jenis sampel dibuat, yaitu, komposit Epoksi/E-Glass dan Epoksi/E-Glass/Clay dengan komposisi clay 1 wt%, 3 wt % ,dan 5 wt %, yang difabrikasi dengan metode hand lay-up. Berdasarkan hasil uji tarik dan uji tekuk, nilai kuat tarik dan kuat tekuk tertinggi diperoleh pada komposit Epoksi/E-glass/Clay dengan fraksi beratclay 3 wt %, yang berturut-turut kenaikan kuat tarik dan kuat tekuknya sebesar 182,24% dan 23,5% terhadap komposit Epoksi/E-glass/Clay. Sedangkan nilai modulus tarik dan modulus tekuk pada komposit Epoksi/E-glass/Clay dengan fraksi berat clay 3 wt % memiliki nilai 11,5 GPa dan 6,04 GPa secara berturut-turut. Pengamatan permukaan patahan menggunakan Scanning Electrons Microscope menunjukkan jenis-jenis mode kegagalan yang terjadi adalah fiber pull-out, delaminasi, kegagalan matriks, fiber patah, dan keretakan mikro pada matriks. Selain itu, sisa matriks yang cukup banyak di fiber pada komposit Epoksi/E-glass/Clay dibanding komposit Epoksi/E-glass menunjukkan ikatan interfacial yang lebih baik saat sejumlah kecil clay ditambahkan.

ABSTRACT
Radar Absorbent Materials are one of new advanced materials to be used in stealth technology. It was an evidence that the addition of a small amount of clay in Epoxy/E-glass composites provided a better electromagnetic wave absorber materials compared to Epoxy/E-glass composites. This research, which was a continuation of the previous research about electromagnetic wave absorption, aimed to study the tensile and flexural properties,as well as the modes failure of Epoxy/E-glass/Clay composites. Four different samples were made; they were Epoxy/E-Glass and Epoxy/E-Glass/Clay with 1 wt %, 3 wt %, and 5 wt % clay loadings. The samples were fabricated with a hand lay-up method. Tensile and flexural test results showed that the highest tensile and flexural strengths were obtained on the Epoxy/E-glass/Clay with 3 wt % clay?s weight fraction, which was increased up to 182,24 % and 23,5 % respectively from the tensile strength and flexural strength of Epoxy/E-glass composites. The tensile and flexural modulus values of Epoxy/E-glass/Clay composites with 3 wt % clay?s weight fraction were 11,3 GPa and 6,04 GPa respectively. An observation of fracture surface using Scanning Electrons Microscope showed that the failure modes that occurred on the fracture surfaces were fiber pull-out, delamination, matrix failure, fiber fracture, and matrix micro-cracks. Moreover, some amount of remaining matrix on the glass fiber at Epoxy/E-glass/Clay composites compared to Epoxy/E-glass composites showed that a better interfacial bond was obtained when a small addition of clay were added"
2016
S63112
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>