Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 68308 dokumen yang sesuai dengan query
cover
Rosalind Fawnia Margeritha
"Light curing unit atau yang biasa disebut (LCU) adalah alat yang berfungsi untuk memperbaiki kondisi gigi yang rusak. Tujuan dari penelitian ini adalah untuk mengetahui optimasi terbaik dan pengaruh frekuensi tinggi pada iradiansi LED pada LCU menggunakan metode pulse width modulation (PWM). Metode PWM dilakukan dengan menerapkan frekuensi tinggi dan rendah untuk menghasilkan nilai iradiansi yang diinginkan dengan tetap memperhatikan suhu LCU tersebut. Hasil percobaan menunjukkan bahwa suhu terendah terdapat pada frekuensi 0,5 kHz. Hasil pengukuran menunjukkan nilai iradiansi sebsar 350 mW/cm2 dengan suhu 29,3 oC. Hasil percobaan menunjukkan bahwa frekuensi dan nilai iradiansi berpengaruh dengan meningkatnya arus. Dimana hasil menunjukkan arus tertinggi sebesar 0,6 terjadi pada frekuensi 125 kHz dengan siklus 100%.  Hasil penyinaran dan pengerasan prototipe dan LCU yang terdapat di pasaran pun diukur kekerasan resin kompositnya menggunakan alat ukur digital durometer hardness shore D tester dan dapat diketahui bahwa hasil pennyinaran dan pengerasan resin komposit dari prototipe sama dengan   LCU yang sudah terdapat dipasaran.

Light curing unit or commonly called (LCU) is a tool that works to improve the condition of damaged teeth. The purpose of this study is to determine the best optimization and effect of high frequency on the LED irradiance in the LCU using the pulse width modulation (PWM) method. The PWM method is carried out by applying high and low frequencies to produce the desired irradiance value while still observing the LCU temperature. The experimental results show that the lowest temperature is found at a frequency of 0.5 kHz. Where the measurement results show the value of irradiance is 350 mW/cm2 with a temperature of 29.3 oC. The results of the experiment show that the frequency and value of the irradiance affect the current increase. Where the results show the highest current of 0.6 occurs at a frequency of 125 kHz with a cycle of 100%. The results of irradiation and hardening of the prototype and LCU found in the market were measured by the hardness of the composite resin using a digital measuring instrument durometer shore D hardness tester and it can be seen that the results of irradiation and hardening of the composite resin from the prototype are the same as the LCU already in the market."
Depok: Fakultas Teknik Universitas Indonesia, 2019
T55296
UI - Tesis Membership  Universitas Indonesia Library
cover
Abdul Rachman Firdaus
"Pemakaian LCU dengan irradiansi tinggi secara medis berpotensi merusak jaringan pulpa gigi akibat kenaikan suhu yang ditimbulkan. Tujuan penelitian ini adalah memperoleh prototipe LCU menggunakan High Power LED dengan 3 mode Pulse Width Modulation (PWM) untuk mengontrol sinar irradiansi sinar output pada mode 1 dengan irradiansi 800 mW/Cm2, mode 2 dengan irradiansi 900 mW/Cm2, mode 3 dengan irradiansi 1.000 mW/Cm2 yang berdurasi 5 detik, 10 detik dan 20 detik dan suhu sinar output ≤ 37 °C. Lampu yang digunakan LED biru high power komersial Model LZ4-00DB10 sebagai sumber sinar.
Pengukuran irradiansi dan suhu dengan menggunakan LED Radiometer dan Thermocouple. Pada penelitian ini dihasilkan Prototipe LCU LED dengan metode kombinasi Pulse Width Modulation pada Mode 3 irradiansi 999 ± 3,16 mW/cm2 dan suhu sinar output 38,76 °C dengan durasi waktu penyinaran 20 detik. Pengaturan kombinasi PWM perlu disempurnakan lagi agar irradiansi diatas 1000 mW/cm2 dapat tercapai, sedangkan suhu sinar output LCU LED dapat terkendali tidak melebihi ≤ 37 °C.

LCU with high irradiance medically potentially damage the dental pulp tissue due to the temperature rise caused objective of this study is to obtain a prototype LCU using High Power LED with 3 modes Pulse Width Modulation (PWM) to control the output light beam irradiance in mode 1 with irradiance of 800 mW / cm2, mode 2 with irradiance of 900 mW / cm2, mode 3 with irradiance of 1,000 mW / cm2 which lasts 5 seconds, 10 seconds and 20 seconds and the temperature of the output beam ≤ 37°C. Commercial high power blue LED as a light source LZ4- 00DB10 model.
Irradiance and temperature measurement using the LED Radiometer and Thermocouple. In this study produced prototype LED LCU with a combination method Mode Pulse Width Modulation at 999 ± 3 irradiance of 3.16 mW / cm2 and a temperature of 38.76°C output beam with a duration of 20 seconds exposure time. PWM combination settings need to be revised so that the irradiance above 1000 mW / cm2 can be achieved, while the temperature of the output beam can be controlled LED LCU not ≤ 37°C.
"
Depok: Program Pascasarjana Universitas Indonesia, 2015
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Manalu, Gabriel Anderson
"Peralatan biomedis yang beredar di Indonesia sebagian besar masih diimpor dari luar negeri, termasuk Dental LED Light Curing Unit (LCU). Padahal kebutuhan akan peralatan biomedis seperti LED LCU selalu meningkat. LED LCU sendiri memiliki sistem kerja yang sederhana, sehingga sangat mungkin untuk menciptakan LED LCU di Indonesia. Penelitian ini berfokus pada realisasi serta evaluasi rancangan wireless dental LED LCU. Wireless dental LED LCU merupakan jenis dental LED LCU yang menggunakan sumber energi baterai sehingga mudah untuk digunakan dalam keadaan apapun. Evaluasi pemilihan frekuensi, duty cycle, serta durasi penyinaran dilakukan setelah melakukan berbagai pengukuran dan pengujian pada penelitan ini.
Beberapa jenis pengukuran dan pengujian yang dilakukan, seperti irradiansi LCU, suhu, kekerasan material hasil polimerisasi serta karakteristik kelistrikan yang semuanya dilakukan terhadap 6 buah LCU dengan 2 jenis LED Dental berbeda. Pulse Width Modulation (PWM) digunakan untuk mengendalikan tingkat irradiansi pada LCU. Hasil akhir rancangan LCU dalam penelitian ini mampu menghasilkan irradiansi lebih dari 800 mW/cm2, suhu tidak lebih dari 50°C, dan harga komponen yang sekitar Rp. 337.000. Rancangan LCU memiliki kinerja yang lebih baik bila dibandingkan dengan LCU komersial yang memiliki rentang harga yang sama, dengan sistem optimal LCU adalah durasi 5 detik dan level duty cycle 0,6 atau 60% yang mampu melakukan polimerisasi resin dental sampai mencapai tingkat kekerasan standar material terpolimerisasi.

The biomedical equipment in Indonesia is mostly still being imported from overseas, including a Dental LED Light Curing Unit (LCU). The need for biomedical equipment such as LED LCU is always increasing. LED LCU itself has a simple working system, so it is very possible to create LED LCU in Indonesia. This research focuses on the realization and evaluation of the wireless dental LED LCU. Wireless dental LED LCU is a type of LCU dental LED that uses a battery energy source, so it is easy to use in any condition. Selection evaluation of the frequency, duty cycle, and the irradiation duration is carried out after measurements and test on this research.
In this research, there are several types of measurements and tests carried out, such as LCU irradiance, temperature, the hardness of the polymerized material and electrical characteristics which all are carried out on 6 LCUs with two different types of Dental LEDs. Pulse Width Modulation (PWM) is used to control the level of irradiance at LCU. The final results of the LCU design in this study were able to produce irradiance of more than 800 mW / cm2, a temperature of no more than 50°C, and a component price of around Rp. 337,000. The LCU design has a better performance when compared to commercial LCU which has the same price range, with an optimal LCU system that is 5 seconds in duration and a duty cycle level of 0.6 or 60% that is capable of polymerizing dental resins to the standard hardness level of polymerized material.
"
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Teguh Handoyo
"Penggunaan LCU berirradiansi tinggi secara medis berpotensi merusak jaringan pulpa gigi akibat kenaikan suhu yang ditimbulkan. Tujuan penelitian ini adalah untuk memperoleh LCU LED dengan metode kombinasi PWM dengan durasi penyinaran selama 20 detik untuk mendapatkan irradiansi ≥ 1200 mW/cm2 dan suhu sinar output ≤ 37℃. Mode PWM disusun dengan menggunakan kombinasi penyinaran irradiansi sinar output rendah (PWM 3/7) dengan penyinaran irradiansi tinggi (PWM 6/7) dalam 5 mode. LED biru high power komersial Model Pl.02.Xl.04041 sebagai sumber sinar. Hasil menunjukkan bahwa irradiansi sinar output adalah 715 ± 24 mW/cm2 dan suhu sinar output adalah 37,4 ± 0,6 °C. Untuk menghasilkan irradiansi sinar output yang lebih tinggi, studi lebih lanjut akan meningkatkan metode kombinasi PWM dan LED untuk mencapai irradiansi sinar output ≥ 1200 mW/cm2 dengan mempertahankan suhu sinar output 37,5 ° C.

The use of high-energy LCU LED may potentially damage dental pulp tissues due to temperature rise caused by. The objective of this research is to obtain a LED LCU using PWM combination methods with time irradiation of 20 seconds to obtain irradiance beam output ≥ 1200 mW/cm2 and light temperature output ≤ 37 ℃. PWM mode is programmed by combining a low output of  irradiance beam (PWM 3/7) with a high irradiance beam (PWM 6/7) into 5 modes. A 5 W blue LED high power Model Pl.02.Xl.04041 was used as a source of light. Results showed that the irradiance beam output was 715 ± 24 mW/cm2 and the temperature output was   37.4 ± 0.6 ° C. To produce a higher irradiance beam output, further study would be to improve the combination of PWM method and LED source  in order to reach the irradiance beam output ≥ 1200 mW/cm2 with maintained light temperature output of  37.5 °C."
Jakarta: Fakultas Kedokteran Universitas Indonesia, 2013
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
cover
Ogy Kurnia Akbar
"Inverter merupakan komponen yang penting pada mobil listrik. Komponen ini digunakan untuk mengkonversi tegangan DC (Direct Current) yang berasal dari baterai menjadi tegangan AC (Alternating Current) yang masuk ke dalam motor listrik. Inverter umumnya juga disebut sebagai komponen kontrol pada kendaraan listrik karena besarnya torsi dan kecepatan kendaraan listrik ditentukan oleh sinyal yang diberikan inverter ke motor listrik. Dengan semakin berkembang pesatnya kendaraan listrik di beberapa tahun belakangan ini, pentingnya untuk memulai rancang bangun sistem inverter yang digunakan pada kendaraan listrik. Sistem inverter dirancang untuk memiliki tegangan opersional maksimum 100V dan frekuensi switching hingga 10 kHz sehingga dapat digunakan khususnya pada pengaplikasian sepeda motor listrik. Pada penelitian ini akan membahas mengenai proses rancang bangun inverter dua tingkat tiga fasa. Proses dilakukan mulai dari pembangkitan sinyal Sinusoidal Pulse Width Modulation (SPWM) tiga fasa yang menjadi metode switching sistem inverter menggunakan mikrokontroler LAUNCHPADXL-F28379D. Kemudian dilanjutkan dengan desain skematik rangkaian, pengujian rangkaian melalui perangkat lunak, desain PCB, dan desain tiga dimensi sistem inverter. Terakhir desain sistem inverter yang telah dibuat akan dimanufaktur serta diuji coba secara open loop pada rangkaian beban hubung wye menyerupai beban motor listrik tiga fasa. Sistem inverter ini sudah sukses diuji coba secara tiga fasa dengan tegangan sumber 100V dan frekuensi switching 10 kHz pada sebuah beban lampu 220V 200W hubung Wye dan mengkonsumsi daya sekitar 40W.

Inverter is essential component that is used in electric car. This component is used to convert DC (Direct Current) Voltage from battery to AC (Alternating Current) Voltage into electric motor. Commonly Inverter also being called as electric motor control component because of how much amount of torque and speed of a electric vehicle are decided by signal given by the inverter to electric motor. With rapid growth of electric vehicle in these recent years, it is important to start designing and manufacturing inverter system which used in electric vehicle. The inverter system is designed to have a maximum operational voltage of 100V, and up to 10 kHz switching frequency so it could be specifically used for electric motorcycle application. In this study will be covering about process of design and development two level inverter system. Process begins with generating Sinusoidal Pulse Width Modulation (SPWM) signal as the switching method for inverter system using LAUNCHPADXL-F28379D Microcontroller. Then continued with designing electric circuit schematic, electric circuit testing using software, designing PCB, and designing 3D of inverter system. Last, the design that has been done will be manufactured and later will be tested by open loop on Wye network circuit load which resembles three phase load. The inverter system has been successfully testes via three phase with 100V voltage source and 10 kHz to a wye network circuit 220V 200W lamp load and consuming power around 40W."
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Leo Kusuma
Depok: Fakultas Teknik Universitas Indonesia, 2004
S39287
UI - Skripsi Membership  Universitas Indonesia Library
cover
cover
Anjanette Pinasthika Alexander
"Resin komposit Bulk-Fill merupakan material yang dapat merestorasi kavitas dengan kedalaman 4-5 mm dalam satu kali penyinaran. Polimerisasi resin komposit dipengaruhi oleh durasi penyinaran dan metode penyinaran Light Curing Unit. Polimerisasi adekuat diperlukan untuk mendapatkan kekerasan permukaan dan Depth of Cure yang optimal. Penelitian ini dilakukan untuk mengetahui kekerasan permukaan dan Depth of Cure resin komposit Bulk-Fill yang disinar menggunakan Light Curing Unit penyinaran pulsa selama 5, 10, dan 20 detik. Spesimen berjumlah 30 buah dibagi berdasarkan kelompok perlakuan yaitu kelompok durasi penyinaran (5, 10, dan 20 detik) dan penyinaran (pulsa dan kontinu). Spesimen berdiameter 6 mm dan tebal 4 mm diuji menggunakan Knoop Microhardness Tester dengan beban indentasi 50 g selama 10 detik pada 5 titik berbeda. Hasil penelitian menunjukkan peningkatan kekerasan permukaan yang disinar dengan Light Curing Unit penyinaran pulsa dan kontinu seiring pemanjangan durasi penyinaran. Terdapat perbedaan bermakna (p<0,05) pada kekerasan permukaan di kelompok durasi penyinaran. Pada nilai depth of cure dengan kedua Light Curing Unit tidak terdapat perbedaan bermakna (p>0,05). Sehingga disimpulkan, penyinaran pulsa Light Curing Unit selama 5, 10, dan 20 detik pada resin komposit Bulk-Fill mengalami peningkatan kekerasan permukaan yang signifikan dan penggunaan dua metode penyinaran sama baik pada nilai depth of cure.

Bulk-Fill composite resin have been introduced with the purpose of time savings. It can be placed in a 4-5 mm thickness bulks to be photo-cured in one step. Polymerization of composite resins affected by the irradiation time and mode. Adequate polymerization is needed to obtain optimal surface hardness and Depth of Cure. This study aimed to evaluate the influence of different exposure time with pulse-lighting mode on Bulk-Fill composite resin surface microhardness and Depth of Cure. Thirty specimens divided into 3 groups of exposure time (5, 10, and 20 sec) and 2 groups of irradiation mode (pulse and continuous), 6 mm in diameter and 4 mm in thick were prepared. Each specimen was measured using Knoop Microhardness Tester at each surface. The result showed that irradiation of Bulk-Fill composite resin with pulse-lighting mode curing unit for 5, 10, and 20 seconds experienced a significant increase in surface hardness. The depth of cure values shows no significant difference among different irradiation mode. It was concluded that that Bulk-Fill composite resin irradiated at longer exposure time exhibited significantly higher surface microhardness than those irradiated at shorter time. Meanwhile, there was no significant difference between two different irradiation mode for depth of cure."
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Mesy
"Latar belakang: Resin komposit Bulk-fill merupakan material tumpatan gigi yang dapat digunakan pada kavitas gigi posterior sedalam 4-5mm dengan satu kali penyinaran. Durasi penyinaran dan metode penyinaran mempengaruhi derajat polimerisasi dari suatu material tumpatan gigi. Sehingga derajat polimerisasi akan mempengaruhi sifat mekanik salah satunya adalah kuat tarik diametral suatu material resin komposit Bulk-fill. Tujuan: Untuk mengetahui kuat tarik diametral resin komposit Bulk-fill yang disinar menggunakan Light Curing Unit eksperimental metode penyinaran pulsa dan Light Curing Unit komersial metode penyinaran kontinu selama 5 detik, 10 detik dan 20 detik. Metode: Enam puluh spesimen resin komposit Bulk-fill (diameter 6mm dan ketebalan 3mm) yang dibagi menjadi 2 kelompok metode penyinaran (pulsa dan kontinu) dan 3 kelompok durasi penyinaran (5 detik, 10 detik, 20 detik) dan direndam didalam 5ml akuades kemudian disimpan dalam inkubator 37oC selama 24 jam. Spesimen lalu dilakukan uji kuat tarik diametral menggunakan Universal Testing Machine dengan beban uji sebesar 250kgFdengan crosshead speed 0,5 mm/menit Hasil: Terdapat peningkatan nilai kuat tarik diametral selama 5 detik, 10 detik dan 20 detik pada metode penyinaran pulsa (53,90±8,53 MPa, 54,94±7,68 MPa, 56,18±6,99 MPa) dan metode penyinaran kontinu (53,26±5,78 MPa, 56,40±5,15 MPa, 57,17±5,70 MPa). Uji One-Way ANOVA menunjukkan tidak terdapat perbedaan yang bermakna (p>0,05) antara durasi penyinaran dan juga metode penyinaran. Kesimpulan: Kuat tarik diametral pada metode penyinaran pulsa memiliki nilai yang lebih rendah dibandingkan dengan metode penyinaran kontinu.

in posterior tooth cavities as deep as 4-5mm with one curing. The duration and method of curing affect the degree of polymerization of a tooth filling material. Therefore, the degree of polymerization will affect the mechanical properties, one of which is the diametral tensile strength of a Bulk-fill composite resin material. Objective: To determine the diametral tensile strength of Bulk-fill composite resins cured using the experimental Light Curing Unit pulses curing method and commercial Light Curing Units with continuous curing method for 5 seconds, 10 seconds and 20 seconds. Method: Sixty Bulk-fill composite resin specimens (6mm diameter and 3mm thickness) were divided into 2 groups of curing methods (pulses and continuous) and 3 groups of curing duration (5 seconds, 10 seconds, 20 seconds) then immersed in 5 ml distilled water and stored in 37oC incubator for 24 hours. Specimens were then tested with diametral tensile strength using a Universal Testing Machine with a test load of 5 kN with a crosshead speed of 0.5 mm/minute. Result: There was an increase in diametral tensile strength values for 5 seconds, 10 seconds, and 20 seconds in the pulse curing method (53.90 ± 8.53 MPa, 54.94 ± 7.68 MPa, 56.18 ± 6.99 MPa) and also an increase in the continuous curing method (53.26 ± 5.78 MPa, 56.40 ± 5.15 MPa, 57.17 ± 5.70 MPa). One-Way ANOVA test showed no significant difference (p> 0.05) between each duration and method of curing. Conclusion: The diametral tensile strength of the pulse curing method has a lower value compared to the continuous irradiation method."
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>