Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 29175 dokumen yang sesuai dengan query
cover
Kevin Fitzgerald Senewe
"Refraksi, gradien refraksi, dan k-factor adalah parameter yang berguna untuk memprediksi kondisi propagasi gelombang radio di lapisan troposfer. Ketiga parameter tersebut diperoleh dari pengukuran suhu udara, kelembaban relatif dan tekanan atmosfer. Skripsi ini telah melakukan percobaan eksperimental sistem Internet of Things berbasis LoRa untuk menentukan refraksi radio secara real-time. Pengukuran secara real-time akan membantu seorang network engineer yang ingin merancang sistem komunikasi di suatu lokasi karena data yang diperoleh adalah data yang spesifik untuk lokasi tersebut, bukan data wilayah secara keseluruhan. Sistem terdiri dari sensor suhu dan humiditas untuk memperoleh data cuaca. Data tersebut akan diteruskan ke server ThingSpeak melalui Gateway LoRa, yang dimana data tersebut akan diolah dengan MATLAB secara real-time dan hasilnya akan ditampilkan di channel ThingSpeak. Skripsi ini telah melakukan uji coba sistem dan berhasil diperoleh hasil refraksi radio. Pengujian dilakukan pada satu titik di area Sawangan, Depok, Indonesia pada hari Kamis tanggal 21 Mei 2020 dan Sabtu tanggal 30 Mei 2020 pada pukul 07:00 WIB hingga 21:00 WIB. Pengujian dilakukan dalam kondisi outdoor. Tanggal 21 Mei 2020, rata-rata nilai k-factor adalah 0.973 dan gradien refraksi adalah 4.304 Unit/Km. Tanggal 30 Mei 2020, rata-rata nilai k-factor adalah 0.972 dan gradien refraksi adalah 4.491 Unit/Km. Kondisi refraksi di Sawangan, Depok pada hari Kamis tanggal 21 Mei 2020 dan Sabtu tanggal 30 Mei 2020 adalah sub-refraksi.

Refractivity, refractivity gradient, and k-factor are useful parameters for predicting the propagation conditions of radio waves in the troposphere. Those three parameters are obtained from the measurements of air temperature, relative humidity, and atmospheric pressure. This thesis has conducted an experiment in creating a LoRa-based Internet of Things system that can determine the radio refractivity in real-time. Real-time radio refractivity measurements will help network engineers when designing communication systems because the data obtained by this system are data specifically for that location, not the overall area. This system consists of temperature and humidity sensors to obtain weather data. The data will then be forwarded to the ThingSpeak server via the LoRa Gateway, which will be processed in MATLAB in real time and the results will be displayed on the ThingSpeak channel. This thesis has tested the system and successfully obtained the results of radio refractivity. These tests were conducted at one point in the Sawangan area of Depok, Indonesia on May 21, 2020 and May 30, 2020 at 07:00 WIB until 21:00 WIB. The testing is done in outdoor conditions. On May 21, 2020, the average k-factor value was 0.973 and the refraction gradient was 4.304 Units/Km. On May 30, 2020, the average k-factor value was 0.972 and the refraction gradient was 4.491 Units/Km. The refractive condition in Sawangan, Depok on May 21, 2020 and May 30, 2020 is sub-refraction.
"
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aswin Tresna Nugraha
"ABSTRACT
Skripsi ini melaporkan percobaan eksperimental sistem Internet of Things untuk melacak dan memantau pasien dengan gangguan mental. Sistem ini dioperasikan pada pita frekuensi ISM yang memanfaatkan teknologi LoRa . Ini terdiri dari klien multinode LoRa , yang merupakan perangkat pelacakan yang terpasang di sisi pasien, mengumpulkan informasi GPS latitude dan longitude untuk ditampilkan di Google Maps di sisi server. Kami telah melakukan uji coba terhadap 3 skenario kondisi lingkungan yang berbeda, yaitu Line of Sight LoS , Non-Line of Sight N-LoS , dan Crowded Area . Penilaian dilakukan dengan mengumpulkan 23 data iterasi pada 10 spot area. Dalam skenario kondisi Line of Sight dengan daya sinyal transmisi data maksimum adalah -73dB yang meliputi area maksimum 38,04 meter. Dalam skenario kondisi Non-Line of Sight, sistem ini mencapai kekuatan sinyal maksimal -74dB dan meliputi area seluas 114,76 meter. Dalam skenario kondisi Crowded Area , sistem dapat mencapai kekuatan sinyal maksimum -88 dB yang meliputi area 234,02 meter. Sistem ini mengindikasikan performa error rendah, meski koneksi yang hilang sering terjadi di beberapa titik. Sistem Internet of Things yang diusulkan masih perlu melakukan perbaikan besar dengan memodifikasi sistem antena.

ABSTRACT
This paper reports the experimental trials of IoT system for tracking and monitoring the patient with mental disorder. The system is operated on the ISM frequency band utilizing the LoRa technology. It consists multinode LoRa client, which is a tracking device installed on the patient side, collecting the GPS information latitude and longitude to be displayed on Google Maps at the server side. We have conducted trials on 3 different environment scenarios, i.e. Line of Sight LoS , Non Line of Sight N LoS , and The ldquo crowded area rdquo . The assessment is conducted by collecting 23 data iterations at 10 spots area. In The LoS scenario, the maximum data transmission signal power is 73dB covering the maximum area of 38.04 meters. In the NLoS scenario, the system achieve maximum signal strength of 74dB and covering the area of 114.76 meters. In the ldquo crowded area rdquo scenario, the system may achieve a maximum signal strength of 88 dB covering the area of 234.02 meters. The system has indicated a low error performance, despite the connections rsquo lost is frequently occurred at several spots. The proposed IoT system is still need to run a major improvement by modifying its antenna system."
2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muhammad Ayyasy
"Teknologi Internet of Things (IoT) merupakan terobosan teknologi yang memungkinkan adanya pengumpulan dan pertukaran data antara objek objek yang saling terhubung dalam suatu jaringan tertentu sehingga, memudahkan akses terhadap data yang didapatkan untuk dikelola menjadi sebuah informasi yang bermanfaat. Implementasi teknologi IoT dapat dimanfaatkan di berbagai bidang sebagai solusi efisiensi, kemudahan, dan keamanan. Pada riset ini, teknologi IoT diimplementasikan sebagai sistem untuk solusi masalah keamanan dan kemudahan pada kendaraan bermotor. Sistem dirancang dengan menggunakan komponen GPS untuk melacak posisi bujur lintang kendaraan, relay untuk memutus rangkaian kelistrikan kendaraan, dan sensor MPU6050 sebagai pendeteksi getaran mencurigakan pada kendaraan. Semua informasi yang didapatkan pada setiap sensor diproses oleh ESP32 kemudian dikirimkan ke server dengan bantuan LoRa. Informasi yang tersimpan di database server dapat diakses melalui aplikasi hasil rancangan. Dari rancangan sistem yang telah ditetapkan, didapatkan sebuah alat yang dapat digunakan untuk melacak dan mengendalikan nyala mati mesin kendaraan melalui sebuah aplikasi hasil rancangan bernama MOTRAV. Kendaraan yang dipasangi alat dapat diubah statusnya ke dalam mode parkir yang akan mengirimkan notifikasi peringatan apabila terdapat suatu gerakan atau getaran yang terdeteksi mencurigakan.

Internet of Things (IoT) technology is a technological breakthrough that allows the collection and exchange of data between objects that are connected to each other in a certain network, making it easier to access the data obtained to be managed into useful information. The implementation of IoT technology can be utilized in various fields as a solution for efficiency, convenience, and security. In this research, IoT technology is implemented as a system for solving security and convenience problems in vehicles. The system is designed using GPS components to track the longitude and latitude position of the vehicle, relays to disconnect the vehicle's electrical circuit, and MPU6050 sensors as suspicious vibration detectors on the vehicle. All information obtained on each sensor is processed by ESP32 and then sent to the server with the help of LoRa. Information stored in the server database can be accessed through the designed application. From the system design that has been determined, a device is obtained that can be used to track and control the turning off of a vehicle engine through a designed application called MOTRAV. The vehicle installed with the device can be changed into parking mode which will send a warning notification if there is a suspicious movement or vibration detected.
"
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Arrief Rahman
"ABSTRAK
Penelitian ini merupakan rancang bangun dan evaluasi dari prototipe Internet of Things IoT menggunakan teknologi LoRa pada frekuensi 868 MHz dan 915 MHz yang merupakan frekuensi ISM Band. Saat ini, penggunaan teknologi LoRa di Indonesia belum marak dilakukan. Namun, untuk masa yang akan datang teknologi LoRa akan marak digunakan di Indonesia untuk mendukung kemajuan di bidang teknologi informasi dan komunikasi, khususnya dalam hal smart city. Permasalahan yang ada pada saat ini adalah belum adanya data yang menunjukkan performa teknologi LoRa dari segi kekuatan sinyal RSSI dan delay transmisi data pada ruang terbuka. Penulis melakukan evaluasi kinerja teknologi LoRa pada dua kondisi, yaitu Line of Sight LoS yang dilakukan di lingkungan Fakultas Teknik Universitas Indonesia dan Non-Line of Sight Non-LoS di Proyek Jalan Tol Cinere-Jagorawi. Perangkat prototipe ini disusun oleh sensor suhu, perangkat LoRa sebagai transmitter dan receiver data yang dikirimkan, mikrokontroller Arduino sebagai pengontrol rangkaian elektronik, dan visualisasi data menggunakan Thingspeak yang merupakan cloud server di web browser. Hasilnya menunjukkan bahwa prototipe bekerja dengan baik pada kedua kondisi tersebut, sementara hasil RSSI bervariasi antara -50 dB hingga -105 dB. Pada LoRa frekuensi 915 MHz kondisi LoS, hasil RSSI berada pada rentang -55 dB hingga -90 dB untuk jarak 100 meter sampai 700 meter. Sedangkan LoRa frekuensi 868 MHz kondisi LoS, hasil RSSI berada pada rentang -69 hingga -99 dB untuk jarak 100 meter sampai 1500 meter. Pada LoRa frekuensi 915 MHz kondisi Non-LoS, hasil RSSI berada pada rentang -61 dB hingga -101 dB untuk jarak 100 meter sampai 400 meter. Sedangkan LoRa frekuensi 868 MHz kondisi Non-LoS, hasil RSSI berada pada rentang -56 dB hingga -101 dB untuk jarak 100 meter sampai 500 meter. Dengan demikian, LoRa dengan frekuensi 868 MHz memiliki performa yang lebih baik dalam segi jarak yang dicapai, delay transmisi data, dan kekuatan sinyal atau RSSI yang terdeteksi dibandingkan LoRa dengan frekuensi 915 MHz. Selain itu, teknologi LoRa terbukti dapat digunakan secara efisien untuk aplikasi IoT dari kedua kondisi LoS dan Non-LoS dengan desain yang harus disesuaikan.

ABSTRACT
This research is a design and evaluation of the prototype Internet of Things IoT using at frequencies 868 MHz and 915 MHz which is the ISM frequency band. Currently, the use of LoRa technology in Indonesia has not been rife. However, for the future, LoRa technology will be used in Indonesia to support the progress of information and communication technology, especially in the case of smart city. The current problem is the lack of data showing the performance of LoRa technology in terms of signal strength RSSI and data transmission delay in open space. The authors evaluate the performance of LoRa technology in two conditions, namely Line of Sight LoS at Faculty of Engineering Universitas Indonesia and Non Line of Sight Non LoS at Cinere Jagorawi Toll Road Project. This prototype device is composed by a temperature sensor, LoRa device as a transmitter and receiver of transmitted data, Arduino microcontroller that acts as an electronic circuit controller, and data visualization using Thingspeak which is a cloud server in web browser. The results have indicated that prorotype is working well on both condition, while RSSI may vary from 50 dB to 105 dB. LoRa with frequency of 915 MHz in LoS condition, RSSI results are at intervals of 55 dB to 90 dB for a distance of 100 meters to 700 meters. Whereas, LoRa with frequency 868 MHz in LoS condition, RSSI results are at intervals of 69 dB to 99 dB for a distance of 100 meters to 1500 meters. At LoRa with frequency 915 MHz in Non LoS condition, the RSSI results are at intervals of 61 dB to 101 dB for a distance of 100 meters to 400 meters. Whereas, on LoRa with a frequency 868 MHz in Non LoS condition, the RSSI results are at intervals 56 dB to 101 dB for distance 100 meters to 500 meters. Accordingly, LoRa with a frequency 868 MHz has better performance in terms of distance achieved, data transmission delay, and signal strength or RSSI detected than LoRa with frequency 915 MHz. In addition, the LoRa technology is proven to be efficiently used for the IoT applications of both LoS and Non LoS conditions, while a specific design should be adjusted."
2017
S67269
UI - Skripsi Membership  Universitas Indonesia Library
cover
Alahi, Md Eshrat E.
"This book presents the design and development of an Internet of Things (IoT) enabled, smart sensor to detect nitrate contamination in natural water. It considers three different sensors designed, fabricated and configured for nitrate detection: a Graphite/PDMS and Si-based MEMS sensors, and aFR4-based sensor. It also introduces a selective polymer material developed by means of the ion imprinting polymerization technique that was used as a coating on the Si-based MEMS sensor. Further, the book discusses the development of a smart sensing system that can be used to remotely monitor the nitrate concentration in any water. Fully explaining all the techniques used, the book is of interest to engineers, researchers and scientists working in the field of the water-quality measurement."
Switzerland: Springer Nature, 2019
e20509770
eBooks  Universitas Indonesia Library
cover
Akhdan Hilmy Taufiqurrahman
"ABSTRAK
Skripsi ini menganalisa bagaimana range, power consumption pada Dragino LoRa Shield. Pada tahap pertama, dibuat desain embedded system LoRa yang bersangkutan menggunakan aplikasi Node-red. Pada percobaan, diukur power consumption pada berbagai jarak antara client dan server. Jarak yang diuji adalah jarak dimana konektivitas antara client dan server masih terjaga/terhubung. Aplikasi Node-Red yang digunakan untuk menyajikan hasil pengujian menunjukan bahwa konektivitas tetap terjaga hingga 1700 cm indoor, dan 1.980 km outdoor. Selain itu, melalui pengukuran yang dilakukan diketahui bahwa daya yang dikonsumsi adalah 0.103 watt untuk indoor, dan 0.103 watt untuk outdoor.

ABSTRACT
This final project explains the implement of sensor and humidity sensor namely DHT11 on LoRa Client and LoRa Server, in using application of IoT. The implement of how to connect using range, Power Consumption with Dragino LoRa Shield. In this work, the design of embedded of LoRa system connected can be served by Node red application. The result of the measured range between LoRa Client and LoRa Server. The range which is measured, is the connectivity between client and server is still connected. Node Red application is used to present the result research which is presenting that the indoor connectivity is still exist to 1700 cm, and the outdoor reaches 1.980 km. Besides that, the result of power consumption in indoor and outdoor are 0.103 watt. "
2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Mochammad Anugrah Agung
"Skripsi ini bertujuan membuat sistem untuk memantau kondisi jantung manusia secara nirkabel dengan menggunakan antenna teksil yang mempunayi frekuensi kerja 2,45 GHz. Sistem ini terdiri dari pemancar (transmitter) dan penerima (receiver) Hasil rancangan sistem komunikasi ini telah diuji dengan menggunakan scenario pengujian untuk komunikasi on-body dan komunikasi off-body yang dilakukan di Laboratorium Telekomunikasi FTUI. Untuk proses validasi data, hasil pembacaan oleh sistem telah dibandingkan dengan uji klinis laboratorium yang dilakukan pada Raditya Medical Centre.
Hasil pembacaan sistem mempunyai bentuk yang mirip dengan hasil uji klinis EKG. Perbedaan bentuk EKG yang diperoleh terjadi pada variasi besarnya amplitudo yang didapatkan, hal ini disebabkan oleh terdapatnya Electromagnetical Interference disaat pengujian sistem dan kurang merekatnya kontak yang terjadi antara elektroda dengan kulit subjek.

This bachelor thesis is aimed to design wireless ECG system for heart monitoring using a textile antenna at 2.45 GHZ of ISM band. The system constructed by two main sub-systems, the transmitter and receiver. System has been tested using several off-body and on-body measurement scenarios at Telecommunication Laboratory FTUI. For data's verification, the system?s result has been compared with clinical trials at Raditya Medical Centre.
The result show that the shape of the received ECG signals is precisely similar with the clinilal ECG signal, although some various amplitude occurs between three consecutive pulses. The differences between received single and clinical trials are caused by the electrodes are not tightly coupled to the patient and Electromagnetic intereference is occured when the system is being tested.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S63174
UI - Skripsi Membership  Universitas Indonesia Library
cover
"Automatic Link Establishment (ALE) dapat digunakan untuk pengamatan propagasi gelombang radio HF (3-30MHz) secara real time. Dari hasil penerapan yang dilakukan, diperoleh data yang mewakili kondisi propagasi suatu sirkit komunikasi radio HF secara real time. Data yang diperoleh meliputi nilai frekuensi yang dapat digunakan, kualitas sinyal, dan identitas stasiun penerima. Informasi dari data tersebut disajikan secara real time dalam bentuk grafis pada sebuah alamat website yang dapat diakses secara umum, yakni www.hflink.net. Informasi grafis yang dihasilkan merupakan garis penghubung antara stasiun dengan warna yang berbeda-beda. Warna tersebut menyatakan nilai frekuensi kerja yang dapat digunakan. Selain itu berdasarkan hasil analisis perbandingan antara data dari salah satu sirkit ALE dengan hasil pengamatan menggunakan Ionosonda, diperoleh kesesuaian data ALE dengan variasi lapisan ionosfer. Berdasarkan hasil tersebut, maka sistem ALE untuk pengamatan propagasi gelombang radio HF secara real time dapat diterapkan.
"
621 DIRGA 12:1 (2011)
Artikel Jurnal  Universitas Indonesia Library
cover
Wisma Chaerul Karunianto
"ABSTRAK
Eksperimen merupakan suatu tahapan belajar yang bertujuan untuk melengkapi proses pembelajaran dikelas. Pada beberapa institusi pendidikan, eksperimen tidak terfasilitasi dengan baik, kurangnya jumlah alat, staff perawatan, serta ruang dan waktu menjadi masalah utama dalam pelaksanaan proses belajar ini. Pembuatan suatu modul eksperimen yang bersifat remote diharapkan dapat mengatasi hal tersebut. Modul eksperimen ini dibangun dengan menjalankan Raspberry Pi sebagai sebuah Server Web sekaligus media menjalankan program eksperimen. Pembuatan Server Web dilakukan menggunakan Nodejs sedangkan pembangunan laman web dibangun dengan bootsrap. Modul eksperimen yang dibangun mengambil studi kasus eksperimen difraksi celah banyak, dengan memvariasikan jarak melalui antarmuka website kita dapat mengamati perubahan pola difraksi yang muncul pada layar pengamatan.

ABSTRACT
Experiment is a learning phase that aims to be a complementary learning process that has been done in class. In some educational institutions, experiments are not well facilitated. The main problem in the implementation of this learning process is the lack of tools, maintenance staff, and space and time. The development of a remote experimental module is expected to overcome this. This experiment module is built by running Raspberry Pi as a Web Server as well as a medium running an experimental program. Web Server Development is done using Nodejs while web page development is built with bootsrap. The experimental module constructed takes the case study of diffraction grating experiments, by varying the distance through the website interface we can observe changes in the diffraction patterns that appear on the observation screen."
2017
S67004
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sulthan Abdul Hafizh Allam
"Seiring bertambahnya jumlah populasi manusia, kebutuhan air bersih merupakan permasalahan yang signifikan pada beberapa kota di dunia dikarenakan air merupakan salah satu faktor penting dalam kehidupan. Hadirnya konsep Internet of Things (IoT) menciptakan langkah evolusioner dalam menghubungkan manusia dengan mesin di mana dalam konteks ini adalah water flow meter. Implementasi water flow meter berbasis IoT pada perumahan dan bangunan-bangunan komersial maupun industri dapat mengatasi permasalahan kebutuhan air bersih. Penelitian ini bertujuan untuk merancang sistem dashboard monitoring untuk water flow meter secara real-time. Implementasi perangkat ini bertujuan untuk menggantikan sistem water flow meter konvensional yang dianggap kurang efisien dalam banyak faktor. Penelitian ini menggunakan Arduino Uno, ESP32 Development Module, KEPServerEX, Antares platform, dan water flow sensor. Algoritma yang digunakan pada sistem ini adalah penggunaan KEPServerEX dalam mengurangi transmission delay pada proses pengiriman data ke cloud. Data pada sensor yang terhubung pada Arduino Uno akan dikomunikasikan via Serial Communication ke ESP32 yang akan memproses dan mengolah data sebelum dikirimkan ke server Antares via HTTP. KEPServerEX akan dihubungkan ke Arduino Uno via OPC DA Client yang akan membaca dan menyimpan data pada Arduino Uno. Ada dua skema utama dalam sistem ini. Pertama, mikrokontroler akan berperan sebagai client dengan KEPServerEX sebagai server-nya. Kedua, KEPServerEX akan menjadi client dengan platform Antares sebagai server. Pada pengujian sistem, nilai error rate yang diperoleh adalah sebesar 5.295% yang membuat keakuratan sistem ini sebesar 94.705%. Untuk pengujian Quality of Service (QoS), dilakukan pengujian pada dua parameter yaitu Packet Loss dan Transmission Delay. Packet Loss yang diuji pada sistem menghasilkan nilai sebesar 1%. Pengujian kedua dilakukan dengan menentukan delay sistem sebesar 2500 ms, 5000 ms, dan 10000 ms dengan hasil Transmission Delay yang didapat adalah sebesar 2245.025 ms, 3972.325 ms, dan 8855.925 ms. Dengan implementasi dari sistem ini yaitu faktor optimasi yang ditawarkan KEPServerEX, dapat membuat kualitas layanan sistem meningkat dalam pengurangan nilai Transmission Delay. Oleh karena itu, sistem ini sangat efektif untuk penerapan dalam meningkatkan efisiensi dari water flow meter serta human error yang biasanya terjadi saat pengukuran data penggunaan air.

As the human population increases, the need for clean water is a significant problem in several cities in the world because water is one of the important factors in life. The presence of the Internet of Things (IoT) concept creates an evolutionary step in connecting humans with machines which in this context is a water flow meter. The implementation of IoT-based water flow meters in residential and commercial and industrial buildings can overcome the problem of clean water needs. This study aims to design a dashboard monitoring system for real-time water flow meters. The implementation of this device aims to replace the conventional water flow meter system which is considered less efficient in many factors. This research uses Arduino Uno, ESP32 Development Module, KEPServerEX, Antares platform, and water flow sensor. The algorithm used in this system is the use of KEPServerEX in reducing transmission delay in the process of sending data to the cloud. The data on the sensors connected to the Arduino Uno will be communicated via Serial Communication to the ESP32 which will process the data before being sent to the Antares server via HTTP. KEPServerEX will be connected to Arduino Uno via OPC DA Client which will read and store data on Arduino Uno. There are two main schemes in this system. First, the microcontroller will act as a client with KEPServerEX as the server. Second, KEPServerEX will be a client with the Antares platform as a server. In testing the system, the error rate obtained is 5.295% which makes the accuracy of this system 94.705%. For Quality of Service (QoS) testing, two parameters were tested, namely Packet Loss and Transmission Delay. Packet Loss tested on the system produces a value of 1%. The second test was carried out by determining the system delay of 2500 ms, 5000 ms, and 10000 ms with the Transmission Delay results obtained were 2245,025 ms, 3972,325 ms, and 8855,925 ms. With the implementation of this system, namely the optimization factor offered by KEPServerEX, it can make the quality of system service increase in reducing the value of Transmission Delay. Therefore, this system is very effective for application in increasing the efficiency of the water flow meter as well as human errors that usually occur when measuring water usage data."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>