Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 62716 dokumen yang sesuai dengan query
cover
cover
Ivan Sanjaya
"Kelemahan dari penggunaan biomassa sebagai bahan bakar kompor biomassa adalah tingginya emisi CO yang dihasilkan akibat pembakaran yang kurang sempurna yang terjadi pada biomassa tersebut. Penelitian yang telah dilakukan menunjukkan bahwa dengan membuat kompor biomassa dengan metode Top Lit-Up Draft Gasifier, dapat mengurangi emisi CO sampai dibawah 20 ppm dan waktu ignisi kompor yang lebih cepat sekitar kurang dari 1 menit. Metode penelitian yang akan digunakan adalah membuat modifikasi sistem pencampuran udara dengan bahan bakar di ruang pembakaran menggunakan gas wick sehingga menghasilkan pembakaran lebih sempurna. Gas wick yang digunakan memiliki diameter masing-masing 9 cm dan 11 cm sehingga akan membentuk anulus pada ruang pembakaran dengan luas penampang anulus yang berbeda pada masing-masing gas wick tersebut, yaitu dengan luas bukaan anulus sebesar 23,78% dan 48,98%. Gas analyzer digunakan untuk mengetahui emisi CO serta metode water boiling test untuk mengetahui efisiensi termal kompor. Hasil menunjukkan dengan gas wick berdiameter 11 cm dengan rasio antara udara primer dan sekunder sebesar 1,773 menunjukkan kinerja kompor yang paling baik dengan efisiensi termal sebesar 65,734%, suhu api rata-rata yang paling tinggi sebesar 702oC, dan rata-rata emisi CO fase pembakaran sebesar 20,692 ppm.

The disadvantages of the use of biomass as fuel biomass gas stoves is the high CO emissions generated as a result of imperfect combustion that occurs in the biomass. Research that has been conducted shows that by making the biomass stove method Top Lit-Up Draft Gasifier, can reduce CO emissions to below 20 ppm and the time of ignition stove faster about less than 1 minute. To overcome these problems, modification of mixing system need to be made to make the air mixing with the fuel in the combustion chamber using gas wick resulting in more complete combustion. Gas wick that be used in this research had a diameter of 9 cm and 11 cm, respectively, so that it will form an annulus in the combustion chamber with different annulus cross-sectional area of ​​each gas wick, with the cross-sectional area of annulus are 23.78% and 48.98%, respectively. Gas analyzer is used to determine the emissions of CO and water boiling test method to determine the thermal efficiency of the stove. The results show the gas wick with diameter of 11 cm and the ratio between the primary and secondary air for 1.773, show the best stove performance with the termal efficiency of 65,734%, the average flame temperature of 702oC, and the average emission of CO on combustion phase of 20,692 ppm."
Depok: Fakultas Teknik Universitas Indonesia, 2014
S54828
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rizka Widya Ariani
"Energi alternatif yang berkesinambungan dan terbarukan serta berpotensi menjadi bahan bakar adalah biomassa. Biomassa cangkang kakao dipilih karena ketersediannya yang melimpah di Indonesia dan memiliki nilai kalor dan volatile matter yang cukup tinggi. Pembakaran volatile matter dari biomassa akan meminimalkan emisi CO daripada metode pembakaran langsung pada fasa padatan. Kompor Top-Lit Up Draft (TLUD) Gasifier dirancang menggunakan dua buah blower masing-masing untuk udara primer untuk devolatilisasi dan udara sekunder untuk menyempurnakan pembakaran.
Penelitian ini bertujuan untuk mengetahui pengaruh variasi laju kedua udara terhadap optimasi hasil pembakaran meliputi suhu api, emisi CO dan efisiensi termal. Pembakaran mendekati stoikiometrik didapatkan pada rasio 3,00 yang menghasilkan suhu api rata-rata tertinggi 543,67oC. Emisi CO terendah didapatkan pada rasio 3,0 sebesar 61,857 ppm. Efisiensi termal tertinggi pada rasio 2,0 sebesar 21,25%.
Pengaruh total udara yang semakin tinggi akan memaksimalkan pencampuran sehingga reaksi pembakaran menuju sempurna dan emisi CO yang dihasilkan rendah. Namun fluktuasi juga dapat terjadi pada laju alir udara yang besar sehingga emisi CO dapat tinggi. Pembentukan jelaga akibat kekurangan udara sekunder memperkuat radiasi dalam kompor. Efisiensi termal yang tinggi dipengaruhi besar oleh radiasi dari dalam kompor.

Another sustainable and renewable alternative energy sources for fuel is biomass. Cocoa pod husk (CPH) is one of biomass that available in Indonesia in huge quantity. CPH has high calorific value and high volatile matter content so it is potential to be fuel source. Burning of volatile matter from biomass will minimize CO emission inspite of burning the solid phase directly. The Top-Lit Up Draft Gasifier Stove was designed with two blowers that will supply primary air as devolatilization air and secondary air as combustion air.
This research is proposed to measure the optimization of stove combustion using CPH pellets under variation of air flow rate affection, including flame temperature, CO emission, and thermal efficiency. The result is, the near-stoichiometric combustion is reached at ratio 3.00 which resulted highest mean flame temperature at 543.67 oC. The lowest CO emission is obtained at ratio 3.0 as 61.86 ppm. The highest thermal efficiency is obtained through ratio 2,0 at 21.25%.
Effect of increasing the total air flow rate will maximize the mixing of air so that combustion goes to complete and CO emission will be lower. Beside that, fluctuation also can exists in higher air flow rate so CO emission will be higher. The formation of soot that is caused by leak of secondary air will strengthen the radiation inside the stove. The higher thermal efficiency is affected by radiation inside the stove.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
S47267
UI - Skripsi Membership  Universitas Indonesia Library
cover
Harahap, Gihon Andre Asmitra
"Biomassa merupakan salah satu energi alternatif yang secara luas digunakan sebagai bahan bakar kompor di daerah pedesaan. Data menyebutkan bahwa sekitar 55% dari masyarakat Indonesia menggunakan biomassa sebagai bahan bakar kompor dan jumlahnya semakin meningkat. Namun masalah yang ditemukan ketika menggunakan biomassa adalah tingginya emisi CO yang merugikan penggunanya. Penelitian ini bertujuan untuk mendapatkan nilai optimum dari rasio laju alir dari udara sekunder terhadap primer dan untuk mengetahui pengaruh dari peningkatan jumlah udara primer pada jumlah udara yang tetap terhadap emisi CO dan efisiensi termal. Dalam penelitian ini, sebuah kompor gas biomassa dibuat dengan prinsip top lit-up draft gasification (TLUD) dimana api muncul pada bagian atas kompor oleh pembakaran dengan pencampuran gas pirolisa dari tumpukan pellet TKKS dan udara sekunder. Hasil yang didapatkan bahwa operasi kompor mendekati keadaan stoikiometrik ketika mencapai rasio laju alir udara 4,06 dengan emisi CO sebesar 88,33 ppm , suhu api rata-rata 532,074oC dan efisiensi termal 29,52%. Emisi CO rata-rata terendah sebesar 66,56 ppm pada rasio 6,64. Efisiensi termal tertinggi sebesar 30,04% pada rasio 6,64. Didapatkan pengaruh laju alir udara bahwa semakin besar rasio udara akan semakin kecil emisi CO yang dihasilkan, dan semakin besar laju alir udara primer emisi CO yang dihasilkan akan semakin besar. Selain itu emisi CO juga meningkat ketika fluktuasi suhu api terjadi. Perpindahan panas dominan di dalam kompor adalah radiasi, yang muncul akibat pembentukan jelaga. Radiasi juga memberikan pengaruh pada suhu api dan efisiensi termal dari kompor.

Biomass is one of alternative energy that has widely used as stove?s fuel particularly in remote area. One data notes that around 55% of all Indonesian people are using biomass as the fuel of their stove and the amount is still increasing. The problem encountered of using conventional biomass stoves which currently use direct combustion of biomass is still emitting much higher CO consequently the emission is not safe for the stove users. This research is proposed to obtain optimum value of secondary to primary air flow ratio and to see effect of increasing primary air flow rate to CO emission and thermal efficiency. In this research, a biomass gas stove has made with top lit-up draft (TLUD) principle where the flame is occured at the top of the stove by combustion of pyrolise gas comes out from the PEFB pellets and secondary air mixing. The result has obtained that near-stoichiometric condition is achieved when the ratio is 4,06 with CO emission is 88,33 ppm, average flame temperature is 532,074oC and thermal efficiency is 29,52%. The lowest average CO emission is 66,56 ppm at ratio of 6,64. The highest thermal efficiency is 30,04% at ratio of 6,64. This research also obtains that increasing air flow ration will decrease CO emission and increasing primary air flow rate will be increasing CO emission also. Another result is CO emission is increasing when flame fluctuation is occured. The dominant heat transfer on the stove is radiation, which is occured by soot formation. Radiation also affects the flame temperature and thermal efficiency of the stove."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S52758
UI - Skripsi Membership  Universitas Indonesia Library
cover
cover
R. Febry Rizqiardihatno
"Biomassa merupakan salah satu sumber energi terbarukan. Biomassa dapat dijadikan bahan bakar yang antara lain: kayu, arang, kotoran hewan, dan limbah pertanian. Untuk kebutuhan domestik di Indonesia, pemakaiannya lebih sebagai bahan bakar kompor masak dengan kayu yang dibakar langsung. Permasalahan yang sering timbul yaitu efisiensi termal yang rendah sehingga menghabiskan banyak bahan bakar yang dapat memperparah deforestasi, tingginya tingkat emisi CO, hidrokarbon, dan partikulat yang dapat menyebabkan polusi udara.
Penelitian ini dilaksanakan untuk merancang, membuat, dan menguji suatu kompor biomassa berbasis bahan bakar serbuk kayu yang dipeletasi, dengan menitikberatkan pada pengambilan kembali panas yang terbuang pada cerobong asap agar menghasilkan efisiensi termal yang cukup tinggi dan emisi zat berbahaya yang rendah. Dengan tahap penelitian yang diawali perancangan, meliputi perhitungan dan desain dimensi kompor. Tahap fabrikasi, membuat kompor dengan bahan, komponen, dan ukuran sesuai rancangan.
Tahap pengujian, memvariasikan kondisi start-up, jarak garangan dan laju masuk udara untuk menguji efisiensi termal menggunakan metode Water Boiling Test, lalu melakukan uji emisi CO dengan parameter zat polutan menggunakan alat CO Detector 7701. Hasil yang didapatkan dari desain adalah kompor berdiameter dalam 300 mm dan luar 400 mm serta tinggi keseluruhan kompor 700 mm. Untuk sistem perpipaan menggunakan pipa 1.5 inci dan pipa 3 inci. Untuk kinerja kompor, efisiensi termal kompor antara 33-38 % dan emisi CO sebanyak 19-51 ppm yang lebih baik dibandingkan kompor biomassa yang sudah ada.

Biomass is one of Renewable Energy resources. Kinds of biomass which can be used as a fuel are: wood, char, dung and agricultural waste. For Indonesian domestic needs, biomass usually used as a cook stove fuel by burning the wood directly but, the thermal efficiency for direct use process is low and emission of carbon monoxide, hydrocarbon, and particulate matters is high. This research's goal are designing, fabricating and testing a pellet biomass cookstove which focus on extracting flue gas heat from exhaust chimney for giving high thermal efficiency and depositioning dangerous emission.
Step of this research start from designing step, covering calculation and designing stove dimension. Fabrication step is making the stove with material, component and dimension appropriate with the design. Testing step is varying start up condition, distance of grate, and air flow velocity to observe the influence of those parameters to thermal efficiency and CO emission.
Thermal efficiency testing was done using Water Boiling Test method and CO Detector 7701 device for CO emission testing. The results of designing step are ID = 300 mm, OD = 400 mm and total height = 700 mm. For piping system, using 1.5 inch (37.5 mm) pipe as an air inlet pipe and 3 inch (75 mm) pipe as an outlet flue gas pipe. Thermal efficiency of this cookstove is approximately 33-38% with 19-51 ppm CO emission, which better than existing biomass cookstove."
Depok: Fakultas Teknik Universitas Indonesia, 2009
S52184
UI - Skripsi Open  Universitas Indonesia Library
cover
Resiana Winata
"Kompor biomassa konvensional yang ada saat ini masih memiliki permasalahan dengan emisi gas CO yang tinggi dibandingkan kompor LPG. Pada penelitian ini, dirancang suatu kompor gas-biomassa menggunakan prinsip Top- Lit Up Draft Gasifier yang diharapkan menghasilkan emisi gas CO yang rendah dengan membakar gas pirolisis dari pelet biomassa. Kompor memiliki diameter dalam sebesar 15 cm, diameter luar 20 cm, tinggi reaktor gasifikasi 51 cm, dan tinggi keseluruhan 95 cm. Kompor menggunakan pelet biomassa dari limbah bagas yang mengandung volatile matter tinggi. Dengan memvariasikan rasio antara laju alir udara sekunder dan udara primer, didapatkan emisi gas CO ratarata terendah, 16,4 ppm (dengan emisi gas CO maksimum yang diperbolehkan adalah 25 ppm), yang terjadi pada rasio 11:1. Perbandingan antara nilai rasio tersebut menunjukkan suhu api maksimum tertinggi yang dicapai adalah 544,44°C pada rasio 6:1. Menggunakan Water Boiling Test, efisiensi termal tertinggi yang dicapai adalah 55%, dimana waktu tersingkat untuk mendidihkan 1 L air adalah 6 menit. Api kompor berwarna kuning menunjukkan pembentukan jelaga.

Nowadays conventional biomass stoves still have a problem of having high CO gas emission compared to LPG stoves. In this research, a biomass-gas stove has been designed using Top-Lit Up Draft Gasifier principle, which had been expected to have low CO gas emission by burning pyrolysis gas from biopellets. The stove has 15 cm inner diameter, 20 cm outer diameter, 51 cm gasification reactor height, and 95 cm overall height. The stove uses biopellet made of bagasse waste, which have high volatile matters content. By varying the ratio of secondary air flow to primary air flow, it was found that the lowest CO gas emission, 16,4 ppm (with maximum CO gas emission allowable is 25 ppm), occurred at the ratio of 11:1. Comparison of different values of the ratio shows that the highest maximum flame temperature achieved was 544,44oC occurring at the ratio of 6:1. Using Water Boiling Test, the highest thermal efficiency achieved was 55%, which corresponds to the shortest time to boil 1 L of water (6 minutes). The stove has yellow flame that indicates the formation of soot."
Depok: Fakultas Teknik Universitas Indonesia, 2012
S43082
UI - Skripsi Open  Universitas Indonesia Library
cover
Nabila Aditya
"Penggunaan bahan bakar fosil di Indonesia selalu meningkat setiap tahunnya. Hal ini menyebabkan ketersediaan bahan bakar fosil akan berkurang. Penggunaan biomassa sebagai pengganti bahan bakar fosil sudah mulai dilakukan, tetapi karena pengolahannya yang membutuhkan biaya mahal, biomassa belum sepenuhnya berkembang. Penelitian ini berfokus pada penggunaan daun cacah yang jatuh dari pohon sebagai potensi bahan bakar untuk kompor skala rumah tangga dengan melihat karakteristik pembakaran pada kompor, serta kinerja bahan bakar tersebut menggunakan eksperimen water boiling test pada kompor Biolite. Daun cacah yang dijadikan bahan bakar dikeringkan sampai memiliki kandungan air dibawah 10. Variasi suplai udara digunakan untuk melihat perbedaan karakteristik serta kinerja pembakarannya dan jenis kecepatan suplai udara paling efektif yang dapat digunakan untuk memasak.
Dalam eksperimen pembakaran daun, pengeringan daun memiliki peran peran penting karena mengurangi waktu proses drying. Sedangkan pada proses pembakaran, tahap gasifikasi belum tercapai karena api yang dihasilkan belum berwarna biru sempurna dan masih terdapat jelaga pada kompor. Pada eksperimen water boiling test, titik didih dicapai lebih cepat pada fase hot start dibandingkan fase cold start. Sedangkan fase simmering tidak tercapai parameternya karena ukuran ruang bakar yang kecil sehingga hanya dapat membuat bahan bakar sebanyak 100 gram. Efisiensi termal tertinggi fase cold start pada suplai udara 1.86 L/s yaitu sebesar 49.24 , dan efisiensi termal terendah pada suplai udara 2.52 L/s yaitu sebesar 41.73 . Efisiensi termal tertinggi fase hot start pada suplai udara 1.86 L/s yaitu sebesar 56.85, dan efisiensi termal terendah pada suplai f4 yaitu sebesar 42.77.

Fossil fuel in Indonesia is used as the primary energy and over the years have increase in demand. This results in the scarcity of fossil fuel in the year coming. The use of biomass as substitute for fossil fuel over the years are increasing, however the technology to produce good fuel from them is still expensive, and have not been fully develop. This research is focused on the use of shredded leaves from fallen leaves that is potential to be use as fuel for biomass stove applied in household needs, by reviewing its characteristics during combustion in the stove, and also the performance of shredded leaves using water boiling method on Biolite cookingstove. Shredded leaves are dried of until it contains moisture under 10. Variation on this research is on the fan speed to see the different characteristics and performance of the stove, and also witch fan speed is best suited for cooking application.
The drying of the leaves holds great importance on reducing the amount of time needed to dry the leaves using its on flame. However the process of gasification have not been achieve fully do to the color of the flame is not blue and generate tar on the stove. The water boiling test shows that on the hot phase water reaches its boiling point quicker than the cold phase. On the simmering phase the leaves did not reach its parameter due to the size of the burning chamber is too small that could only fit 100 grams of shredded leaves. The highest Thermal efficiency in the cold start phase is on fan speed 1.86 L s which is 49.24 and the lowest is on fan speed 2.52 L s which is 41.73 . The highest thermal efficiency on hot start phase is on the fan speed 1.86 L s which is 56.85 , and the lowest is on fan speed 2.52 L s which is 42.77.
"
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aditya Hartawan
"Kerimbunan di ibukota didukung dengan lahan hijau yang terdiri dari penanaman pohon, mulai dari area perumahan, hingga perkantoran. Sampah daun yang dimiliki pohon pada area tersebut menjadi salah satu kontribusi besar pada sampah organik. Pada umumnya, pengolahan sampah organik tersebut menggunakan metode pembakaran akibat tidak dapat terdekomposisi ke tanah. Hasil pembakaran sampah organik tersebut dapat menjadi sebuah energi terbarukan. Besar energi ini dapat digunakan sebagai bahan bakar untuk rumah tangga. Adapun kompor biomassa sebagai kompor alternatif pengguna bahan bakar selain gas. Hasil pembakaran kompor biomassa merupakan pembakaran yang bersih karena campuran bahan bakar dan udara yang menghasilkan pembakaran sempurna.
Penelitian ini bertujuan untuk mengembangkan potensi energi terbarukan menggunakan daun. Pembakaran yang terjadi pada daun memiliki karakteristik yang berbeda terhadap intensitas udara dengan bentuk olahan briket. Efisiensi bahan bakar dapat diketahui dengan menggunakan metode water boiling test dan pengukuran mass loss rate.
Hasil metode water boiling test dengan olahan briket menunjukkan bahan bakar dapat mendidihkan air pada waktu singkat dan membutuhkan pengisian ulang jika digunakan untuk memasak. Efisiensi termal pada saat masuk pada fase cold start adalah 42 dan hot start pada 46. Bentuk olahan briket menghasilkan pembakaran yang lebih lama namun lebih sukar untuk dinyalakan.

The capital of Indonesia is kept cool and shady by green areas consisting of trees, from residential areas to offices. Fallen leaves produce by these trees contributes to a large amount of organic waste. Generally, the vast majority of the people incinerate these waste as they cannot decomposed quick enough on the ground. The burning of these leaf litters can open up a potential renewable energy. Although the scale of energy than can be use is suited as fuel for household needs. Biomass cooking stoves are developed to accommodate the daily use for cooking as an alternative to gas powered stoves. The flame that is produced by the cooking biomass cooking stove is smokeless due to the great supply of air mixing with the fuel generates a good clean burn.
This research intends to explore and developed the potential of dry leaves form as briquettes as a renewable energy. Burning leaves have different characteristics to the intensity of air going through the combustion chamber with the fuel form of briquettes. The Efficiency of the fuel can be measured using the water boiling test method and mass loss rate.
Results from the water boiling test with the leaf briquettes can bring water to a boil but for standard time of cooking, refuelling in the middle of cooking is needed. The thermal efficiency during the cold phase is 42 and during the hot phase is 46. Although the forming of leaves into briquettes prolong the time of burning and perfect for refuelling, the briquettes are quite hard to ignite.
"
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Raden Bregas Dwi Hatmojo
"Indonesia memiliki sumber daya alam yang berlimpah dan tersebar di seluruh kepulauan. Pemanfaatan potensi sumber daya alam tersebut belum sepenuhnya diperankan dan dikembangkan untuk memenuhi kebutuhan sehari-hari seperti memasak di sektor rumah tangga. Tujuan dari penelitian ini adalah untuk mengeksplorasi potensi dari serasah daun sebagai sumber energi domestik yang digunakan sebagai bahan bakar alternatif. Secara khusus, konfigurasi penelitian skala laboratorium dilakukan dengan menggunakan serasah daun spesies Artocarpus champaden, L., Nephelium lappaceum, L., dan Mangifera indica, L. Di Indonesia spesies ini dikenal sebagai pohon Cempedak, pohon Rambutan, dan pohon Mangga yang menghasilkan gugur daun sepanjang tahun. Upaya yang dilakukan oleh masyarakat dalam menangani serasah adalah mengumpulkan dari halaman atau atap pekarangan rumah kemudian dibakar untuk mengurangi jumlah serasah sebagai pengotor.
Penelitian eksperimental dilakukan melalui beberapa langkah, yaitu pembuatan briket dari serasah daun yang ditambahkan dengan minyak kanola dan pasta tepung jagung sebagai material pengikat dan bertujuan untuk meningkatkan kandungan energi ketika dilakukan proses pembakaran yang diproduksi secara manual dengan sedikit bantuan alat mekanis. Analsis termal termasuk nilai kalor, proksimat dan ultimat dilakukan dengan metode dan peralatan standar. Penelitian menggunakan kompor biomassa dengan volume ruang bakar sekitar 660 cm3. Sebuah kipas elektrik dipasang ke kompor untuk mengalirkan udara. Metode Water Boiling Test dilakukan untuk mengukur karakteristik pembakaran dan efisiensi kompor.
Ditemukan bahwa briket (100 gram) dari semua jenis daun yang diuji dapat merebus air 1000 ml dalam waktu 7 menit. Secara umum, kinerja pembakaran sampel briket dapat dikaitkan dengan analisis proksimat dan ultimat, sehingga dengan membandingkan kinerja menggunakan Water Boiling Test menunjukkan bahwa perbedaan kinerja menggunakan berbagai jenis serasah daun tidak memiliki perbedaan yang signifikan. Penelitian ini menunjukkan bahwa serasah daun memiliki potensi sebagai sumber energi yang dapat diandalkan untuk memasak di rumah tangga di daerah pedesaan.

Indonesia has abundant natural resources spread throughout the islands. The utilization of these natural potentials has not been fully played and developed to meet daily needs such as for cooking. The purpose of this study is to explore the potential of leaf litter as a domestic source of energy for cooking. In particular, a set of laboratory scaled experiment was conducted by using leaf litter of the species Artocarpus champaden, L., Nephelium lappaceum, L., and Mangifera indica, L. In Indonesia these species are known as Cempedak, Rambutan, and Mangga trees which produce fallen leaf throughout the years. A way of reducing the leaf litter problems by local people is by collecting it from the garden and roof, then burn it to reduce the volume. The experimental work was carried out through some steps. The leaf litter was transformed to biomass briquettes fuel in order to increase energy content for combustion by adding Canola Oil and Starch as a binder. The briquettes were produced manually with minimum mechanical works.
Thermal analysis, including calorific value, proximate and ultimate analysis, was performed by standard method and equipment. The experiment was carried out by using a biomass stove with a fuel chamber volume of approximately 660 cm3. A fan was attached to the stove to supply an updraft forced vortex flow of air. Water Boiling Test method was performed to measure the burning characteristic and stove efficiency.
It was found that the briquettes (100 grams) from all leaf type tested can boil the water of 1000 ml within 7 minutes. In general, the burning performance of the briquettes were related to proximate and ultimate analysis of the samples. Nevertheless, by comparing the performance using Water Boiling Test suggested that the discrepancies of the performance using different types of leaf litter were not significant. This work showed that leaf litter has the potential as a reliable energy source for cooking in household at rural areas.
"
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>