Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 159480 dokumen yang sesuai dengan query
cover
Fadhlurrahman Rafi Barori
"Minyak sawit mentah merupakan produk perkebunan terbesar dan menjadi pendulang nilai ekspor bagi Indonesia. Namun, pada produk minyak sawit hasil rafinasi terdapat senyawa kontaminan 3-monochloropropanaediol (3-MCPD) dan apabila dikonsumsi secara berlebih berpotensi menyebabkan penyakit pada ginjal dan testis. Selama ini pengujian kandungan 3-MPCD dilakukan menggunakan alat yang canggih, memerlukan waktu yang lama dan membutuhkan keahlian teknisi yang tinggi. Metode cepat untuk mendeteksi senyawa 3-MCPD masih menjadi tantangan. Penelitian ini bertujuan untuk mengembangkan sensor pendeteksi cepat berbasis kolorimetri menggunakan nanopartikel emas. Sensor nanopartikel emas disintesis dari asam tetrakloroaurat yang direduksi menggunakan senyawa trisodium sitrat. Nanopartikel emas difungsionalisasi oleh capping agent yaitu glutathione (GSH) agar dapat berikatan dengan 3-MCPD. Setiap sampel yang dibuat diuji menggunakan alat berupa UV-Vis spectroscopy UV-Vis, dynamic light scattering (DLS), dan Fourier Transform Infrared (FTIR). Hasil dari penelitian ini didapatkannya komposisi larutan GSH-AuNPs yang stabil. Indikasi deteksi 3-MCPD sangat kuat diwakili oleh turunnya intensitas AnNPs-GSH murni dari 0,8197 menjadi 0,744 ketika dicampurkan 3-MCPD sebanyak 3 ppm. Berdasarkan hal tersebut, dapat disimpulkan GSH-AuNPs berpotensi untuk dikembangkan dalam deteksi 3-MCPD
Crude palm oil is the most extensive product of agriculture in Indonesia and has become a great portion in export value. However, refined palm oil products  contain a harmful substance called 3-monochloropropanaediol (3-MCPD) and if consumed in excess has the potential to cause disease in the kidney and testicle. Detection of 3-MCPD is always dependent on the sophisticated machine, time-consuming and highly skilled technicians. A simple method that proposes rapid detection remains a challenge. Hence, this research  aims to develop a colorimetric-based rapid detection sensor using gold nanoparticles. The sensor material was synthesized from chloroauric acid that was reduced using trisodium citrate to make gold nanoparticle. The gold nanoparticle will be functionalized with a capping agent, glutathione (GSH)  to bind to 3-MCPD. The GSH-AuNPs were tested by UV-Vis spectroscopy (UV-Vis), dynamic light scattering (DLS), and Fourier Transform Infrared (FTIR). The result shows that stable GSH-AuNPs composition has been found. The indication for detection of 3-MCPD is very striking, represented by the decrease in the intensity of pure AuNPs-GSH from 0.8197 to 0.744 when mixed with 3 ppm of 3-MCPD. Based on the results, it can be concluded that GSH-AuNPs have the potential to be developed for the 3-MCPD detector application. "
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Agan Auliya Rahman
"Senyawa 3-monochloropropanediol atau 3-MCPD merupakan senyawa kontaminan pada minyak goreng, yang menyebabkan resiko pada kesehatan manusia, karena bersifat karsiogenik. EU regulation telah membuat aturan maksimal 3-MCPD pada makanan yaitu 2,5ppm. Pengujian kandungan 3-MCPD yang telah ada saat ini, berbasis kromatografi gas, namun mahal, kompleks, dan membutuhkan operator yang berkualifikasi. Pendeteksian senyawa 3-MCPD menggunakan nanopartikel berbasis kolorimetri mendapat perhatian, salah satunya nanopartikel logam yang memiliki sifat sensitif terhadap senyawa yang dideteksi. Pada penelitian ini, deteksi dilakukan dengan nanopartikel tembaga dengan L-sistein sebagai capping agent. Sintesis nanopartikel tembaga dilakukan dengan berbagai variasi untuk mendapatkan hasil yang optimal seperti stokiometri, atmosfer, dan pengenceran. Pita LSPR nanopartikel tembaga dengan ligan L-sistein (Cys-CuNPs) diamati menggunakan UV-visible (UV-Vis). Selanjutnya karakterisasi Fourier-transform infrared spectroscopy (FTIR) dan dynamic light scattering (DLS) dilakukan untuk mengamati interaksi antara nanopartikel tembaga dengan L-sistein serta ukuran partikel Cys-CuNPs. Selanjutnya penelitian ini, dilakukan evaluasi sensitivitas nanopartikel Cys-CuNPs terhadap 3-MCPD
3-Monochloropropanediol (3-MCPD) is a contaminant in edible oil that can pose a risk to human health, because it is carcinogenic. EC regulations have set a maximum limit of 2,5ppm of 3-MCPD on food. The current assay of three-MCPD, based on gas chromatography, is expensive, complex, and requires a qualified operator. The detection of 3-MCPD compound using nanoparticles with colorimetric based has received attention, one of which is metal nanoparticles with sensitive to the detected compounds. In this research, detection was carried out with copper nanoparticles with L-cysteine as a capping agent. The synthesis of copper nanoparticles has been tried with various variations to obtain optimal results such as stoichiometry, atmosphere, and dilution. LSPR bands of copper nanoparticles with L-Cysteine (Cys-CuNPs) were observed using UV-Visible (UV-Vis). In addition, Fourier transform infrared spectroscopy (FTIR) and dynamic light scattering (DLS) were employed to study the interactions between copper nanoparticles and L-cysteine, as well as the particle size of Cys-CuNPs. Furthermore, the sensitivity of Cys-CuNPs to 3-MCPD was evaluated."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aqshal Subakti Rizkita Aziz
"Saat ini, metode pengujian kandungan 3- Monochloropropanediol (3-MCPD) yang merupakan zat kontaminan pada minyak kelapa sawit dilakukan menggunakan instrumen GC-MS. Metode tersebut memerlukan prosedur yang lama dan rumit. Pengembangan nanopartikel emas dengan pengkaping Cysteine berpeluang menjadi solusi untuk mendeteksi 3-MCPD dalam waktu cepat berbasis analisis kolorimetri. Tujuan dari penelitian ini adalah untuk mengetahui kondisi optimal sintesis, ukuran, dan sensitivitas nanopartikel dalam mendeteksi 3-MCPD. Penelitian dilakukan dengan memvariasikan konsentrasi dan volume Cysteine. Variasi konsentrasi Cysteine yang digunakan adalah 0 hingga 0,5 mM, sedangkan variasi volume Cysteine yang dipakai adalah 0 hingga 2 ml. Pengujian 3-MCPD dilakukan dengan variasi konsentrasi 0 hingga 10 ppm. Selanjutnya, karakterisasi dilakukan dengan UV – Vis, FTIR, dan PSA. Sintesis yang optimal didapatkan ketika nanopartikel emas ditambahkan dengan 1 ml 0,025 mM Cysteine menghasilkan warna ruby red yang stabil hingga 24 jam. Ukuran nanopartikel didapatkan 27,1 nm dan terjadi pemutusan ikatan gugus fungsi tiol pada Cys-AuNPs. Nanopartikel emas ini berpotensi untuk dikembangkan lebih lanjut dalam mendeteksi 3-MCPD.

Currently, the assay method of 3-Monochloropropanediol (3-MCPD) which is a contaminant in palm oil is carried out by using the GC-MS instrument. This method requires a long and complicated procedure. The development of gold nanoparticles with cysteine capping has the opportunity to be a solution to detect 3-MCPD in a fast time based on colorimetric analysis. This study aims to determine the optimal conditions for synthesis, size, and sensitivity of nanoparticles in detecting 3-MCPD. The research was conducted by varying the concentration and volume of Cysteine. Cysteine concentration variations used are 0 to 0.5 mM and the volume variation of Cysteine used is 0 to 2 ml. The 3-MCPD test was carried out with a concentration variation of 0 to 10 ppm. Furthermore, characterization was carried out using UV-Vis, FTIR, and PSA. Optimal synthesis was obtained when gold nanoparticles were added with 1 ml of 0.025 mM Cysteine. The color of the nanoparticles is ruby red and stable for up to 24 hours. The nanoparticle size was 27.1 nm, and the thiol functional group bond was broken in Cys-AuNPs. These gold nanoparticles have the potential to be further developed in detecting 3-MCPD."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Lisa Hasnalma Zahra
"Indonesia merupakan salah satu negara pengekspor besar minyak kelapa sawit. Dalam proses pengolahan kelapa sawit menjadi minyak kelapa sawit terutama pada proses deodorisasi menggunakan suhu tinggi, cenderung terbentuk zat 3-monochloropropanaediol (3-MCPD) yang berbahaya bagi kesehatan sehingga harus dideteksi dan dihilangkan. Metode pengujian kandungan zat 3-MCPD yang sudah umum digunakan yaitu GC-MS, namun GC-MS ini mahal, prosesnya kompleks, dan waktu pengujian lama, sehingga dibutuhkan metode alternatif. Penelitian ini menunjukkan metode baru, sederhana, dan efisien untuk tujuan aplikasi deteksi cepat 3-MCPD berbasis analisis kolorimetri dengan menggunakan nanopartikel tembaga. Nanopartikel disintesis menggunakan prekursor CuCl2, ligan L-Glutathione sebagai agen pelindung, dan reduktor hidrazin monohidrat. Nanopartikel hasil sintesis dikarakterisasi dengan UV-Vis, FTIR, dan PSA. Spektroskopi UV-Visible (UV-Vis) digunakan untuk memantau pita LSPR dari nanopartikel tembaga yang difungsikan L-Glutathione (GSH-CuNPs). Spektroskopi Fourier Transform Infrared (FTIR) memberikan informasi tentang interaksi permukaan antara L-Glutathione dan CuNPs. Penganalisis Ukuran Partikel (PSA) mengkonfirmasi ukuran rata-rata nanopartikel sebesar 57,43 nm. Setelah sintesis, GSH-CuNPs yang didapat diuji sebagai sensor kolorimetri untuk mengetahui keberadaan zat berbahaya 3-MCPD. Sensitivitas nanopartikel terhadap penambahan 3-MCPD 100, 50, 25, 10, dan 5 ppm dievaluasi pada penelitian ini

Indonesia is one of the major exporters of palm oil. In the process of processing crude palm oil into palm oil, especially in the deodorization process using high temperatures, 3-monochloropropanediol (3-MCPD) substances are produced. The presence of this substance possesses health risks, so it must be detected and eliminated. The commonly used content testing method of 3-MCPD is GC-MS. However, this method is expensive, the process is complex, and the testing time is long. Therefore, an alternative method is needed. This study demonstrates a new, simple, and efficient method for the rapid detection of 3-MCPD based on colorimetric analysis using copper nanoparticles. The nanoparticles were synthesized using CuCl2 precursor, L-Glutathione ligand as a protective agent, and hydrazine monohydrate as a reducing agent. The synthesized nanoparticles were characterized by UV-Vis, FTIR, and PSA. UV-Visible (UV-Vis) spectroscopy was used to monitor the LSPR band of L-Glutathione-functionalized copper nanoparticles (GSH-CuNPs). Fourier Transform Infrared (FTIR) spectroscopy provides information on the surface interactions between L-Glutathione and CuNPs. The Particle Size Analyzer (PSA) confirmed the average nanoparticle size of 57.43 nm. After synthesis, the obtained GSH-CuNPs were tested as colorimetric sensors to determine the presence of the hazardous substance 3-MCPD. The sensitivity of nanoparticles to the addition of 3-MCPD 100, 50, 25, 10, and 5 ppm was evaluated in this study"
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Pangiastika Putri Wulandari
"ABSTRAK
Kebutuhan bahan pembersih yang terus meningkat dapat menyebabkan meningkatnya pencemaran lingkungan akibat penggunaan detergen komersial yang mengandung surfaktan bersifat toksik, seperti Sodium Lauryl Sulfate SLS , Linear Alkylbenzene Sulfonate LAS dan Sodium Laureth Sulfate SLES . Surfaktan Methyl Ester Sulfonate MES dapat mensubstitusi surfaktan toksik tersebut dalam detergen. Pembentukan MES dilakukan dengan esterifikasi dan transesterifikasi crude palm oil, sulfonasi, pemurnian, dan penetralan. Nanomaterial fotokatalis TiO2 ditambahkan sebagai bahan aditif untuk meningkatkan kinerja surfaktan dalam mengangkat kotoran dan mendegradasi senyawa organik. Variasi komposisi surfaktan MES dan TiO2 dilakukan untuk memperoleh kestabilan detergen. Teknik analisis data dalam penelitian ini adalah karakterisasi metil ester, surfaktan MES, dan detergen menggunakan instrumen spektrofotometer UV-Vis, FTIR, GC-MS, dan LC-MS. Kondisi optimum pada proses esterifikasi dan transesterifikasi adalah rasio mol 1:6 antara CPO dan metanol berdasarkan konversi tertinggi, yaitu 99 . Kondisi optimum proses sulfonasi adalah rasio mol 1:5 antara metil ester dan NaHSO3 berdasarkan nilai tegangan permukaan terendah, yaitu sekitar 36 dyne/cm . Komposisi detergen yang menunjukkan kestabilan terbaik adalah 0,1 TiO2-3 MES-2 CMC yang memiliki kemampuan mengangkat kotoran sekitar 86 dan sisa surfaktan dalam air sisa cucian menjadi sekitar 33.

ABSTRACT
The increasing need for cleaning agents can lead to increased environmental pollution due to the use of commercial detergents that containing toxic surfactants, such as Sodium Lauryl Sulfate SLS , Linear Alkylbenzene Sulfonate LAS and Sodium Laureth Sulfate SLES . The Methyl Ester Sulfonate MES surfactant may substitute the toxic surfactant in the detergent. The formation of MES is carried out by esterification and transesterification of crude palm oil, sulfonation, refining, and neutralization. The photocatalyst nanoparticle TiO2 is added as an additive to improve surfactant performance in removing impurities and degrading organic compounds. Variations of MES surfactant and TiO2 compositions were performed to obtain detergent stability. Data analysis technique in this research is methyl ester, MES surfactant, and detergent characterization using UV Vis spectrophotometer instrument, FTIR, GC MS, and LC MS. The optimum condition in esterification and transesterification process is 1 6 mole ratio between CPO and methanol based on the highest conversion, 99 . The optimum condition of the sulfonation process is the 1 5 mole ratio between methyl ester and NaHSO3 based on the lowest surface tension value, which is about 36 dyne cm. Detergent composition which showed the best stability was 0.1 TiO2 3 MES 2 CMC which has the ability to remove impurities by 86 and the remaining surfactant in residual water was 33."
2017
S67767
UI - Skripsi Membership  Universitas Indonesia Library
cover
Defi Sulistyoningsih
"Jenis logam berat yang sering ditemui sebagai pencemar di perairan Indonesia adalah Timbal (Pb) dan Kadmium (Cd). Metode pendeteksian logam berat yang telah banyak dikembangkan sebelumnya tidak dapat dilakukan secara on-site dan masih membutuhkan biaya yang mahal. Salah satu alat yang berpotensi untuk mengatasi hal tersebut adalah paper electroanalytical device (PAD). Penelitian yang akan dilakukan adalah memfabrikasi paper electroanalytical device (PAD) dengan metode gabungan, yaitu metode elektrokimia dan kolorimetri. Material kertas yang akan digunakan adalah Whatman no.1 yang difabrikasi dengan metode wax printing dan screen printed carbon electrode (SPCE). Pada bagian elektrokimia, working electrode akan dimodifikasi dengan menggunakan nanopartikel emas (AuNPs) untuk meningkatkan performa perangkat elektrokimia pada PAD. Pada bagian kolorimetri, AuNPs yang dimodifikasi dengan tiosulfat (S2O32-) akan digunakan sebagai reagen deteksi. Hasil pengujian elektrokimia, deposisi AuNPs pada elektroda kerja meningkatkan nilai sensitivitas sebesar 48,1% pada logam Pb dan 77,3% pada logam Cd. Pada pengukuran logam Pb, nilai LOD sebesar 21,8 ppb menurun menjadi 13,7 ppb, dan untuk nilai LOQ dari 72,8 ppb menjadi 45,96 ppb. Sedangkan, pada pengukuran Cd nilai LOD sebelum deposisi sebesar 23 ppb, dan menurun menjadi 18 ppb, dan untuk LOQ dari 77,5 ppb menurun menjadi 62,1 ppb. Hasil pengujian kolorimetri menunjukkan bahwa sampel lingkungan 1 mengandung 68,2 ppb logam Pb dan sampel lingkungan 2 mengandung 65,4 ppb logam Pb.

The heavy metals that are often found as pollutants in Indonesian waters are Lead (Pb) and Cadmium (Cd). Heavy metal detection methods developed previously cannot be carried out on-site and still require high costs. One tool that has the potential to overcome this is a paper electroanalytical device (PAD). The research to be carried out is to fabricate paper electroanalytical devices (PAD) with a combined method, namely electrochemical and colourimetric methods. The paper material to be used is Whatman no.1, which was fabricated using the wax printing and screen printed carbon electrode (SPCE) method. In the electrochemistry section, the working electrode will be modified using gold nanoparticles (AuNPs) to improve the performance of electrochemical devices on PAD. In the colourimetry section, AuNPs modified with thiosulfate (S2O22-) will be used as a detection reagent. The electrochemical test results showed that the deposition of AuNPs on the working electrode increased the sensitivity value by 48.1% for Pb metal and 77.3% for Cd metal. In the measurement of Pb metal, the LOD value of 21.8 ppb decreased to 13.7 ppb, and the LOQ value from 72.8 ppb to 45.96 ppb. Meanwhile, for Cd measurements, the LOD value before the deposition was 23 ppb and decreased to 18 ppb, and for LOQ, from 77.5 ppb, it decreased to 62.1 ppb. The results of the colorimetry test showed that environmental sample 1 contained 68.2 ppb of Pb metal and environmental sample 2 contained 65.4 ppb of Pb metal."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Dawami Arijan
"Nanopartikel emas (AuNP) merupakan salah satu jenis nanopartikel yang banyak dikembangkan dalam pemanfaatannya di bidang biomedis. Berbagai metode telah diciptakan dalam proses fabrikasi AuNP. Dari berbagai metode tersebut didapatkan berbagai variasi jenis, bentuk, dan ukuran AuNP. Salah satu jenis nanopartikel emas yang cukup mendapat perhatian adalah AuNP berpori. Nanomaterial berpori memiliki perbandingan rasio volume dan luas permukaan yang tinggi juga volume pori yang besar sehingga banyak diteliti dalam berbagai aplikasi teknologi termasuk sistem penghantaran obat. Review kali ini membahas proses sintesis AuNP berpori secara cepat dan sederhana melalui berbagai metode seperti kimia basah, sacrificial template, green synthesis, filtrasi vakum, dan galvanic replacement. Dari proses sintesis nanopartikel emas berpori, dihasilkan ukuran partikel bervariasi antara 17,1-1000 nm dengan berbagai bentuk dengan kestabilan yang baik. Review ini menunjukkan bahwa nanopartikel emas berpori yang disintesis dengan sederhana dan cepat cenderung stabil untuk digunakan dalam berbagai jenis aplikasi.

Gold nanoparticles (GNP) are a type of nanoparticle that has been widely developed for use in the biomedical sector. Various methods have been found in the GNP fabrication process. From these various methods, various types, shapes and sizes of GNP were obtained. One type of gold nanoparticle that has received considerable attention is porous GNP. Porous nanomaterials have high volume and surface area ratios as well as large pore volumes so that they are widely studied in various applications including drug delivery systems. This review discusses the quick and simple synthesis process of porous GNP through various methods such as wet chemical, sacrificial template, green synthesis, vacuum filtration, and galvanic replacement. From the synthesis process of porous gold nanoparticles, the particle sizes varied between 17.1-1000 nm with various shapes with good stability has been produced. This review demonstrates that simple and fast synthesized porous gold nanoparticles are likely to be stable for use in a wide variety of applications."
Depok: Fakultas Farmasi Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
cover
Rizky Priambodo
"ABSTRAK
Kelapa sawit merupakan tanaman perkebunan yang banyak dibudidayakan di Indonesia, dengan luas sekitar 11 juta hektar pada tahun 2014. Serbuk sari kelapa sawit memiliki potensi alergi yang cukup besar, karena memiliki ukuran relatif kecil, berjumlah relatif banyak, dan bersifat anemofili.
Penelitian ini bertujuan untuk mengetahui karakter kandidat protein alergen serbuk sari kelapa sawit melalui metode SDS-PAGE dan Western Blotting, serta mengetahui aktivitas IgA, IgE, IgG, IgM, dan IFN-γ pada sel Peripheral Blood Mononuclear Cell (PBMC) terhadap induksi protein serbuk sari kelapa sawit yang dilakukan secara in vitro. Penelitian diawali dengan ekstraksi protein serbuk sari kelapa sawit, yang berasal dari beberapa wilayah di Indonesia. Berat molekul protein dianalisis dengan metode SDS-PAGE, serta uji kealergenikan kandidat protein alergen diuji dengan menggunakan 21 serum pasien alergi melalui metode Western Blotting. Protein serbuk sari kelapa sawit juga diinduksikan pada kultur sel PBMC. Proses pendeteksian IgA, IgE, IgG, IgM, dan IFN-γ dilakukan menggunakan metode ELISA. Berat molekul protein serbuk sari kelapa sawit diketahui berukuran 10?80 kDa.
Hasil uji kealergenikan protein tersebut pada Western Blotting menunjukkan kandidat protein alergen memiliki ukuran 14 kDa, 15 kDa, 20 kDa dan 31 kDa. Aktivitas beberapa immunoglobulin dan sitokin berhasil terdeteksi. Konsentrasi IgA didapatkan sebesar 0,022 pg/ml, IgE sebesar 9,655 pg/ml, IgG sebesar 39,856 pg/ml, IgM sebesar 10,369 pg/ml, dan IFN-γ sebesar 2.617,240 pg/ml.

ABSTRACT
Oil palm is a plant that widely cultivated in Indonesia, with an area of about 11 million hectares in 2014. Oil palm pollen is potential to caused allergy, because it has a small size, much in amount, and was dispersed by wind.
This study aims to determine the character of the allergen protein candidate from oil palm pollen by using SDS-PAGE and Western Blotting, and also to know the activity of IgA, IgE, IgG, IgM, and IFN-γ against exposure to oil palm pollen protein performed in vitro on Peripheral Blood Mononuclear Cell (PBMC). The study begins with the protein extraction from oil palm pollen, which is derived from several regions in Indonesia. The molecular weight of these proteins are analyzed using SDS-PAGE. Allergenic test of allergen protein candidates were tested using 21 serum of allergic patients through Western Blotting method. Oil palm pollen protein also induced in PBMC cultures. The detection of IgA, IgE, IgG, IgM, and IFN-γ were performed using ELISA. The molecular weight of oil palm pollen protein is about 10?80 kDa.
Allergenic test results through Western Blotting showed the allergen protein candidates have a size of 14 kDa, 15 kDa, 20 kDa and 31 kDa. Immunoglobulin and cytokine activity successfully detected. The IgA concentrations obtained 0.022 pg/ml, IgE obtained 9.655 pg/ml, IgG obtained 39.856 pg/ml, IgM obtained 10.369 pg/ml, and IFN-γ obtained 2,617.240 pg /ml.
"
Depok: Universitas Indonesia, 2015
T44879
UI - Tesis Membership  Universitas Indonesia Library
cover
Farli Faiqhaidar Farwan
"Persiapan katalis dengan pemanasan standar menghabiskan banyak energi. Sebaliknya, perangkat gelombang mikro dapat mentransfer energi panas langsung ke molekul reaktan bagian dalam. Metode microwave dapat mempersingkat waktu reaksi dari jam menjadi menit. Kalsium oksida (CaO) adalah oksida basa kuat dengan aktivitas katalitik yang cukup besar. Titanium dioksida (TiO2) sebagai pendukung katalis menawarkan kualitas unggul dibandingkan nitrida, perovskit, dan karbida karena stabilitas kimia dan termal yang kuat dari nanopartikel TiO2. Hal ini dapat dilihat sebagai dukungan katalitik heterogen, menjamin stabilitas elektrokimia dan ketersediaan komersial. Pada penelitian ini, katalis CaO/TiO2 dengan perbandingan 1:1 dibuat dengan proses poliol microwave dengan daya microwave 800 W selama 3 menit. Katalis CaO/TiO2 yang dihasilkan mempunyai karakteristik yang mirip di hasil uji SEM, XRD, dan FTIR dengan proses pemanasan konvensional lainnya namun dengan waktu dan konsumsi energi yang singkat. Waktu yang dibutuhkan untuk pembuatan katalis penelitian ini hanya 3 menit dibandingkan 5-6 jam pada proses kalsinasi. Energi yang dikonsumsi pada proses poliol gelombang mikro hanya 0,4 kWh, dibandingkan 256,80 hingga 692,14 kWh pada proses kalsinasi. Menghasilkan konversi 35,17% dan yield 12%, dengan karakteristik biodiesel viskositas 1,15 cSt, densitas 893 kg/m3, dan bilangan iodium 5,7 gI2/100g. Penelitian lebih lanjut perlu dilakukan untuk mendapatkan kondisi optimal.

Catalyst preparation with standard heating consumes a significant amount of energy. In contrast, microwave devices can transfer thermal energy straight into the inner molecules of reactants. The microwave method can reduce the reaction time from hours to minutes. Calcium oxide (CaO) is a strong basic oxide with considerable catalytic activity. Titanium dioxide (TiO2) as catalyst support offers superior qualities to nitrides, perovskites, and carbides due to the strong chemical and thermal stability of TiO2 nanoparticles. It can be viewed as a heterogeneous catalytic support, assuring electrochemical stability and commercial availability. In this research, a 1:1 ratio of CaO/TiO2 catalyst was prepared by microwave polyol process with 800 W microwave power for 3 minutes. The CaO/TiO2 catalyst produced has the same characteristics in SEM, XRD, and FTIR results as other conventional heating processes but with short time and energy consumption. The time needed for this research catalyst preparation is only 3 minutes compared to 5-6 hours by calcination process. The energy consumed by the microwave polyol process is only 0.4 kWh, compared to 256.80 to 692.14 kWh in the calcination process. Resulting in 35.17% conversion and 12% yield, with biodiesel characteristics of 1.15 cSt viscosity, 893 kg/m3 density, and 5.7 gI2/100g iodine value. Further research should be conducted to obtain optimum conditions."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>