Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 185248 dokumen yang sesuai dengan query
cover
Muhammad Faiq Zuhdi
"Kehilangan gigi merupakan masalah yang umum terjadi di masyarakat. Untuk itu diperlukan implant gigi dengan desain dan material yang dapat meningkatkan osseointegrasi dan juga kekuatan mekanik yang baik. Salah satu metode untuk membuat implant gigi ini yaitu dengan metode metal injection molding. Wrought material Ti6Al4V dengan dimensi 5 mm x 5 mm x 3 mm yang sudah dilakukan surface treatment dengan pengamplasan grit P80, P180, dan P600 dimasukkan ke dalam cetakan berbentuk kubus dengan dimensi 5 mm x 5 mm x 5 mm kemudian diinjeksikan Feedstock Ti6Al4V hingga cetakan terisi penuh dan menempel pada wrought material Ti6Al4V. selanjutnya dilakukan proses solvent debinding dengan larutan heksana selama 3 jam pada temperature 60 °C dan dilanjutkan thermal debinding dengan temperature 600 °C dengan heating rate 5 °C/menit dengan waktu tahan 60 menit menggunakan atmosfer argon. Proses sintering menggunakan temperature 1150 °C dengan waktu tahan 60 menit, 90 menit, dan 120 menit pada atmosfer argon dengan flow rate 1 liter/menit. Hasil penelitian menunjukkan bahwa waktu tahan sintering berpengaruh pada persentase porositas dan juga kekerasan material Ti6Al4V. Pada kekerasan material porous Ti6Al4V terdapat peningkatan kekerasan sedangkan pada wrought material Ti6Al4V terjadi penurunan kekerasan pada waktu tahan sintering 120 menit karena fenomena pertumbuhan butir. Kekasaran permukaan sangat berpengaruh pada shear bond strength pada permukaan dengan nilai kekasaran permukaan yang tinggi maka shear bond strength juga akan semakin tinggi. Pada penelitian ini hasil shear stress yang tertinggi sebesar 1,5406 Mpa pada kekasaran permukaan Ra sebesar 2,3677 μm

Tooth loss is a common problem in society. For this reason, dental implants with designs and materials that can improve osseointegration and good mechanical strength are needed. One of the methods for making dental implants is the metal injection molding method. Wrought material Ti6Al4V with dimensions of 5 mm x 5 mm x 3 mm which has been surface treated with grinding paper P80, P180, and P600 is inserted into a cube-shaped mold with dimensions of 5 mm x 5 mm x 5 mm then injected with Feedstock Ti6Al4V until the mold is filled full and attached to the wrought Ti6Al4V material. The solvent debinding process with hexane was carried out for 3 hours at a temperature of 60 °C and continued by thermal debinding at a temperature of 600 °C with a heating rate of 5 °C/minute with a holding time of 60 minutes using an argon atmosphere. The sintering process uses a temperature of 1150 °C with holding times of 60 minutes, 90 minutes, and 120 minutes in an argon atmosphere with a flow rate of 1 liter/minute. The results showed that the sintering resistance time affects the percentage of porosity and also the hardness of the Ti6Al4V material. In the hardness of the porous Ti6Al4V material there is an increase in hardness, while in the wrought material Ti6Al4V there is a decrease in the hardness at a sintering time of 120 minutes due to the grain growth phenomenon. Surface roughness is very influential on the shear bond strength on a surface with a high surface roughness value, the shear bond strength will also be higher. In this study, the highest shear stress was 1.5406 Mpa at a surface roughness Ra of 2.3677 μm"
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Amirah Salsabila Widad Putri
"Kondisi kehilangan gigi dapat menyebabkan gangguan pada efisiensi pengunyahan dan berdampak pada penyakit sistemik. Penggunaan implan gigi menjadi perawatan terbaik dengan manfaat jangka panjang. Untuk mencapai kesuksesan pemasangan implan gigi, produk implan gigi harus memiliki desain optimal guna mempercepat proses osseointegrasi. Alternatif yang dapat meningkatkan osseointegrasi dengan memodifikasi permukaan implan yang berpori. Penelitian ini akan berfokus pada simulasi, desain, dan manufaktur dari screw implan gigi berpori dengan prinsip hybrid porous dimana terdiri dari inti implan gigi yang padat dengan permukaan profil ulir yang berpori. Proses manufaktur akan menggunakan metode metal injection molding (MIM) yang melalui tahapan injeksi, debinding, dan sintering. Hasil green part dari injeksi menggunakan feedstock Ti-6Al-4V yang telah dilakukan menunjukkan adanya kecacatan produk pada profil ulir dan short shot. Proses dilanjutkan ke tahap debinding yang terdiri dari solvent debinding dan thermal debinding. Terakhir, proses sintering dilakukan dengan temperatur 1150°C dan waktu tahan 60 menit. Evaluasi pengamatan mikrostruktur dilakukan untuk mengetahui penampakan dari permukaan berpori yang diketahui memiliki %area porositas sebesar 36.268% untuk produk screw Ti-6Al-4V implan gigi trial.

The condition of tooth loss can disrupt chewing efficiency and have systemic implications. The use of dental implants provides the best long-term treatment option. To achieve successful dental implant placement, the dental implant products must have an optimal design to expedite the osseointegration process. An alternative approach to enhance osseointegration is through modifying the implant surface to incorporate porosity. This study focuses on the simulation, design, and manufacturing of porous screw dental implants using the hybrid porous principle, consisting of a solid core implant with a porous threaded surface. The manufacturing process involves metal injection molding (MIM) with stages of injection, debinding, and sintering. The results of the injection process using Ti-6Al-4V feedstock revealed product defects in the threaded profile and short shots. The process then proceeds to the debinding stage, which includes solvent debinding and thermal debinding. Lastly, sintering is conducted at a temperature of 1150°C and a holding time of 60 minutes. Microstructure observations are performed to examine the appearance of the porous surface, which is known to have a porosity area percentage of 36.268% for the trial Ti-6Al-4V screw dental implant product."
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Kamelia Rinati
"Penambahan dopan logam Cu dilakukan dalam modifikasi permukaan permukaan Ti6Al4V, untuk merancang fotokatalitik sistem dengan efisiensi tinggi di bawah cahaya tampak. Mendopankan logam Cu pada permukaan fotokatalis menggunakan metode photo-assisted deposition. Variasi konsentrasi logam Cu (0,05 M; 0,10 M; 0,15 M) dilakukan untuk memperoleh kondisi optimum fotokatalis yang aktif dibawah cahaya tampak. Hasil karakterisasi SEM-EDX dan XRD, menunjukkan bahwa sampel yang dianodisasi dengan elektrolit gliserol memiliki morfologi dan kristalinitas lebih baik dibandingkan sampel yang dianodisasi dengan elektrolit asam. Hasil uji pembentukan biofilm secara in vitro dengan bakteri Streptococcus mutans menunjukkan sampel yang didopankan dengan dopan Cu berkonsentrasi 0,15 M memiliki kinerja fotokatalitik yang paling baik, dengan hasil sebesar 99% persentase disinfeksi bakteri dibandingkan dengan model kontrol pada jam ke-16 pengukuran. Hasil ini menunjukkan sampel yang didopankan dengan dopan Cu berkonsentrasi 0,15 M merupakan kondisi optimum untuk menghambat pembentukan biofilm dalam penelitian ini

Optimization of morphology and crystallinity of TiO2 nanotubes (TNT) fabricated on the surface of Ti6Al4V with anodizing method using a variation of the type of electrolyte. To design a system with high efficiency photocatalytic under visible light, the addition of a transition metal dopant antibacterial namely Cu (Copper). Cu-doped surface on the dental implat using photo-assisted deposition method. Variations in the concentration of Cu (0.05 M; 0.10 M; 0.15 M) were performed to obtain the optimum conditions photocatalysts active under visible light. Results of SEM-EDX and XRD characterization, indicate that the sample which is anodized with glycerol electrolyte, have better morphology and crystallinity than the sample which is anodized with acid electrolyte. The test results of in vitro biofilm formation test by Streptococcus mutans showed sample of which doped with Cu that have concentration of 0,15 M has the best photocatalytic performance, with percentage of disinfection of bacteria at 99% compared with the control model at 16th hour measurement. These results show the samples TNT/G/0,15 which doped with Cu dopant concentration of 0,15 M is an optimum condition to inhibit biofilm formation in the study"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S64638
UI - Skripsi Membership  Universitas Indonesia Library
cover
Daniel Jones
"Implan gigi merupakan suatu perangkat dari bahan biomaterial yang dipasang dan ditanamkan ke tulang rahang melalui pembedahan sebagai pengganti gigi yang hilang. Topografi permukaan implan gigi dengan kekasaran permukaan dan lapisan berpori telah diusulkan untuk meningkatkan osseointegrasi dan induksi pertumbuhan jaringan tulang baru (bone ingrowth) serta mengurangi efek stress shielding akibat modulus Young yang tinggi dari material implan. Studi ini menyajikan pengembangan desain implan gigi dengan lapisan berpori (hybrid porous dental implant) yang dapat mengisi jalur ulir implan melalui metode metal injection molding (MIM). Fokus studi ini yaitu desain, fabrikasi, dan analisa inti padat implan gigi dari Ti-6Al-4V yang dilakukan dengan mempertimbangkan fitur geometri yang mendukung kesuksesan jangka panjang implan gigi serta dapat dilakukannya proses injeksi feedstock Ti-6Al-4V untuk memenuhi cavity pada inti padat implan gigi baik secara simulasi numerik maupun eksperimental.Implan gigi merupakan suatu perangkat dari bahan biomaterial yang dipasang dan ditanamkan ke tulang rahang melalui pembedahan sebagai pengganti gigi yang hilang. Topografi permukaan implan gigi dengan kekasaran permukaan dan lapisan berpori telah diusulkan untuk meningkatkan osseointegrasi dan induksi pertumbuhan jaringan tulang baru (bone ingrowth) serta mengurangi efek stress shielding akibat modulus Young yang tinggi dari material implan. Studi ini menyajikan pengembangan desain implan gigi dengan lapisan berpori (hybrid porous dental implant) yang dapat mengisi jalur ulir implan melalui metode metal injection molding (MIM). Fokus studi ini yaitu desain, fabrikasi, dan analisa inti padat implan gigi dari Ti-6Al-4V yang dilakukan dengan mempertimbangkan fitur geometri yang mendukung kesuksesan jangka panjang implan gigi serta dapat dilakukannya proses injeksi feedstock Ti-6Al-4V untuk memenuhi cavity pada inti padat implan gigi baik secara simulasi numerik maupun eksperimental.

Dental implant is a device made of biomaterial that is surgically attached and implanted into the jawbone as a replacement for missing teeth. The surface topography of dental implant with surface roughness and porous coating has been proposed to increase osseointegration and induction of bone ingrowth and reduce the stress shielding effect due to the high Young's modulus of the implant material. This study presents the development of a dental implant design with porous coating (hybrid porous dental implant) that can fill the implant thread path through the metal injection molding (MIM) method. The focus of this study is the design, fabrication, and analysis of the solid core of dental implants from Ti-6Al-4V which was carried out by considering the geometric features that support the long-term success of dental implants and the injection of Ti-6Al-4V feedstock to fill the cavity in the solid core dental implants both numerically and experimentally."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Labiyan Asri Laili
"Latar Belakang: Kehilangan gigi merupakan masalah yang sering ditemukan pada lanjut usia (lansia) dan berdampak buruk pada sistem fungsional, struktur anatomi, estetika, emosional, dan sosial. Dokter gigi perlu merekomendasikan perawatan prostodontik untuk merehabilitasi kondisi tersebut, namun kebutuhan perawatan gigi tiruan dikalangan lansia masih sangat terbatas. Dalam kebutuhan perawatan, keadaan sosiodemografi (usia, jenis kelamin, tingkat pendidikan) dan jumlah kehilangan gigi dapat memengaruhi prosesnya. Tujuan: Mengetahui gambaran dan menganalisis hubungan kebutuhan perawatan prostodontik pada pasien lansia berdasarkan keadaan sosiodemografi (usia, jenis kelamin, tingkat pendidikan) dan jumlah kehilangan gigi. Metode: Studi analitik observasional dengan desain cross sectional dan menggunakan data sekunder dari rekam medik pasien baru yang datang pada bulan Januari – November 2022. Rekam medik yang digunakan adalah rekam medik konvensional dan digital dengan dengan teknik pengambilan consecutive sampling. Hasil Penelitian: Distribusi frekuensi kebutuhan perawatan prostodontik didominasi oleh kelompok usia 60-69 tahun (56.9%), perempuan (58.8%), tingkat pendidikan Perguruan Tinggi (PT) dan Sekolah Menengah Atas (SMA) (39.2%), jumlah kehilangan gigi sebanyak gigi (74.5%), dan jenis perawatan yang paling banyak dibutuhkan yaitu Gigi Tiruan Lengkap (GTL) (54.9%). Uji chi-square menunjukkan adanya hubungan antara jumlah kehilangan gigi dengan kebutuhan perawatan Gigi Tiruan Jembatan (GTJ), Gigi Tiruan Sebagian (GTS), dan GTL (p=0.000) serta terdapat hubungan antara tingkat pendidikan dengan kebutuhan perawatan GTL (p=0.017). Namun, tidak terdapat hubungan antara usia dan jenis kelamin dengan kebutuhan perawatan GTJ, GTS, dan GTL (p 0.05). Kesimpulan: Penelitian ini menunjukkan adanya hubungan kebutuhan perawatan prostodontik dengan tingkat pendidikan dan jumlah kehilangan gigi pada pasien lansia di RSKGM FKG UI.

Background: Tooth loss is a problem that is often found in the elderly and has a negative impact on functional systems, anatomical structures, aesthetics, emotional and social. The dentists will recommend prosthodontic treatment to rehabilitate this condition, but the need for denture treatment among the elderly is still limited. In terms of treatment needs, sociodemographic (age, gender, level of education) and the number of missing teeth can influence the process. Objective: Knowing the description and analyzing the relationship between the need for prosthodontic treatment in elderly patients based on sociodemographic conditions (age, gender, level of education) and the number of missing teeth. Methods: Observational analytic study with cross-sectional design and using secondary data from the medical records of new patients who arrived in January – November 2022. The medical records used were conventional and digital medical records with consecutive sampling technique. Result: The frequency distribution of the need for prosthodontic treatment was dominated by the age group 60-69 years (56.9%), women (58.8%), higher education level and senior high school (39.2%), the number of missing teeth was >6 teeth (74.5%), and the type of treatment most needed is complete denture (54.9%). The chi-square test showed that there is a relationship between the number of missing teeth and the need for fixed partial denture, removable partial denture, and complete denture treatment (p=0.000) and there is a relationship between education level and complete denture treatment needs (p=0.017). However, there is no relationship between age and gender with the need for fixed partial denture, removable partial denture, and complete denture treatment (p 0.05). Conclusion: This study shows that there is a relationship between prosthodontic treatment need with education level and the number of missing teeth in elderly patients at RSKGM FKG UI. "
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Eka Hertanto Syafei
"Modifikasi Permukaan Ti6Al4V dengan variasi metode anodisasi yang berupa variasi tegangan 30, 40, 50, dan 60 volt dengan menggunakan pengadukan magnetic stirrer dan variasi waktu anodisasi 30, 60, dan 90 menit dengan menggunakan pengadukan ultrasonic telah selesai dilakukan. Hasil karakterisasi pada sampel menunjukan adanya perubahan diameter TiO2 nanotubes pada variasi tegangan anodisasi dan juga perubahan kristalinitas bahan pada variasi tegangan anodisasi dan waktu anodisasi. Hasil uji anti bakteri menunjukan bahan implant Ti6Al4V yang dimodifikasi pada tegangan 50 volt dengan menggunakan pengadukan ultrasonic selama 30 menit memiliki kinerja anti bakteri yang terbaik, dimana dapat mendisinfeksi bakteri hinggan 90.36% dibandingkan dengan model kontrol pada jam ke 24 pengujian. Hal ini menunjukan bahwa bahan implant Ti6Al4V yang dimodifikasi pada tegangan 50 volt dengan menggunakan pengadukan ultrasonic selama 30 menit merupakan kondisi optimum untuk mendapatkan bahan dengan sifat anti bakteri. Kinerja anti bakteri pada bahan implant Ti6Al4V berpotensi untuk ditingkatkan dengan kombinasi teknologi lainnya.
Ti6Al4V surface modification with anodizing variation method in form of voltage variation of 30, 40, 50, and 60 volt by using magnetic stirrer and time variation of 30, 60, and 90 minutes by using ultrasonic had been done. Characterizations of the samples show the change of TiO2 nanotubes diameter on voltage variation and crystalinity of the material upon on voltage and time variation. Antibacterial tests show that material modification on 50 volt by ultrasonic for 30 minutes produces the best result, which can achieve 90.36% bacterial disinfection compared to the control. The result shows that Ti6Al4V that is modified on 50 volt by ultrasonic for 30 minutes is the best condition to achieve anti bacterial tooth implant material. Further research can be done on Ti6Al4V material to increase anti bacterial ability by combine it with other technology."
Depok: Fakultas Teknik Universitas Indonesia, 2015
S58725
UI - Skripsi Membership  Universitas Indonesia Library
cover
Byrne, Gerard
"Fundamentals of Implant Dentistry is a basic guide to foundational knowledge and skills and their application in clinical practice. More comprehensive than a procedural atlas and more accessible than a specialist reference, this text is an indispensable tool for dental students and clinicians beginning work with dental implants.
Fundamentals of Implant Dentistry provides a concise yet comprehensive look at the basic background and science of implantology and includes practical, evidence‐based instruction on common procedures such as single implant crowns, bridges and overdentures. Well‐illustrated with clear line drawings and clinical photos, the book serves as the perfect introduction to this exciting area of dentistry."
Chichester: Wiley Blackwell, 2014
617.693 BYR f
Buku Teks SO  Universitas Indonesia Library
cover
Hanover Park: IL Quintessence Publishing Co. Inc., 2015
617.693 FUN
Buku Teks SO  Universitas Indonesia Library
cover
Siahaan, Gebri Connidio
"Untuk mengatasi kehilangan gigi diperlukan implan gigi yang tahan terhadap korosi. Penelitian ini bertujuan untuk mengetahui morfologi lapisan dan ketahanan korosi Hidroksiapatit (HAp)/Multi Walled Carbon Nanotube (MWCNT) pada substrat Stainless Steel (SS) 316L sebagai implan gigi. Metode yang digunakan untuk melapisi SS 316L dengan HAp/MWCNT adalah metode Electrophoretic Deposition (EPD). Tegangan EPD dilakukan pada 20, 30, dan 40 V selama 20 menit dengan pelarut aseton. Morfologi lapisan HAp/MWCNT dianalisis dengan Scanning Electron Microscope (SEM). Hasil SEM menunjukkan tegangan 20 dan 30 V memiliki morfologi lapisan yang homogen sedangkan tegangan 40 V mengalami terjadinya aglomerasi. Uji korosi dengan metode Potentiodynamic Polarization (PDP) dan Electrochemical Impedance Spectroscopy (EIS) menunjukkan pelapisan HAp/MWCNT melindungi substrat SS 316L dari korosi dalam larutan Simulated Body Fluid (SBF). Sampel dengan kualitas terbaik diperoleh pada tegangan 30 V karena memiliki morfologi lapisan yang homogen sehingga menghasilkan laju korosi yang rendah (0,0745 mpy).

To address tooth loss, corrosion-resistant dental implants are required. This research aims to investigate the morphology and corrosion resistance of Hydroxyapatite (HAp)/ Multi Walled Carbon Nanotube (MWCNT) coatings on Stainless Steel (SS) 316L substrates for dental implants. The electrophoretic deposition (EPD) method was employed to coat SS 316L with HAp/MWCNT. EPD was carried out at 20, 30, and 40 V for 20 minutes using acetone as the solvent. The morphology of the HAp/MWCNT coatings was analyzed using Scanning Electron Microscopy (SEM). SEM results revealed that coatings at 20 and 30 V exhibited a homogeneous morphology, while agglomeration occurred at 40 V. Corrosion tests, conducted using Potentiodynamic Polarization (PDP) and Electrochemical Impedance Spectroscopy (EIS) methods in Simulated Body Fluid (SBF) solution, demonstrated that the HAp/MWCNT coatings protected the SS 316L substrate from corrosion. Samples coated at 30 V exhibited the highest quality due to their homogeneous morphology and low corrosion rate (0.0745 mpy)."
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Lieando Chandra
"Latar belakang: Gigi tiruan dukungan implan, salah satu perawatan kehilangan gigi terbaik, diterima luas di seluruh dunia. Namun, penggunaannya di Indonesia masih relatif rendah. Studi terkait kesadaran (awareness), pengetahuan (knowledge), dan sikap (attitude) terhadap implan gigi telah banyak dilakukan di negara lain, tetapi belum pernah dilakukan di Indonesia. Tujuan: Mengembangkan kuesioner kesadaran, pengetahuan, dan sikap pasien terhadap implan gigi yang valid dan reliabel. Metode: Penelitian kualitatif melalui studi literatur pada 9 studi, wawancara semi-struktur 8 pakar implan dan 10 subjek kehilangan gigi, focus group discussion, dan uji-coba kuesioner. Penelitian kuantitatif pada 227 subjek untuk pengujian validitas dan reliabilitas kuesioner. Hasil: Kuesioner final 28 item (domain kesadaran, pengetahuan, dan sikap) berhasil dikembangkan dengan validitas isi (content validity) dan validitas muka (face validity) terpenuhi. Analisis faktor dapat dilakukan pada ketiga domain berdasarkan hasil Uji Kaiser-Meyer Olkin (KMO) dan Uji Bartlett (0,680;P<0,05| 0,922;P<0,05| 0,849;P<0,05). Uji validitas konvergen dan uji konsistensi internal Cronbach’s alpha menghasilkan nilai baik pada domain kesadaran (r=0,736; P<0,05; α=0,848), domain pengetahuan (r=0,616; P<0,05; α=0,922), dan domain sikap (r=0,658; P<0,05; α=0,794). Kesimpulan: Kuesioner kesadaran, pengetahuan, dan sikap pasien terhadap perawatan dengan implan gigi teruji valid dan reliabel untuk mengevaluasi kesadaran, pengetahuan, dan sikap pasien terhadap perawatan dengan implan gigi di Indonesia.

Background: Implant-supported prosthesis, one of the best treatment for tooth loss, are widely accepted worldwide. However, its utilization is still relatively low in Indonesia. Studies related to awareness, knowledge, and attitude towards dental implants have been conducted in many other countries, but there has been no study in Indonesia. Objective: To develop a valid and reliable questionnaire on patient awareness, knowledge and attitudes towards dental implants. Methods: Qualitative study was done through literature review on 9 studies, semi-structured interviews with 8 implant experts and 10 tooth loss subjects, focus group discussion, and pre-testing. Quantitative study on 227 subjects for validity and reliability test. Results: The final questionnaire of 28 items (awareness, knowledge, and attitude domains) was successfully developed with achieved content validity and face validity. Factor analysis can be performed on all three domains based on the results of the Kaiser-Meyer-Olkin Test (KMO) and Bartlett Test (0.680;P<0.05| 0.922;P<0.05| 0.849;P<0.05). The convergent validity and Cronbach's alpha internal consistency were high in awareness domain (r=0.736; P<0.05; α=0.848), knowledge domain (r=0.616; P<0.05; α=0.922), and attitude domain (r=0.658; P<0.05; α=0.794). Conclusion: The questionnaire developed was valid and reliable to evaluate patient awareness, knowledge, and attitudes towards dental implant treatment in Indonesia."
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2022
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>