Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 8261 dokumen yang sesuai dengan query
cover
cover
Diandra Novita
"Mengkonsumsi minyak diasilgliserol (DAG) dapat mencegah akumulasi lemak dan obesitas. Penelitian ini meneliti tentang teknologi produksi minyak DAG satu tahap dari minyak kelapa sawit menggunakan kombinasi parsial hidrolisis dan parsial esterifikasi menggunakan biokatalis terimmobilisasi di dalam sebuah bioreaktor hollow fiber membran.
Hasil dari reaksi parsial hidrolisis digunakan sebagai umpan reaksi parsial esterifikasi untuk meningkatkan yield minyak DAG. Pengaruh konfigurasi arah aliran minyak dalam sintesis tidak signifikan. Semakin besar konsentrasi enzim yang digunakan, meningkatkan yield minyak DAG yang dihasilkan. Melalui studi laju alir minyak, diperoleh bahwa pada konsentrasi biokatalis 5 mg/mL dan laju alir optimum 0,05 mL/ dihasilkan minyak DAG dengan kemurnian 79,19%.

Consumption of Diacylglycerol (DAG) oil can prevent fat accumulation and obesity. This research investigated one step DAG oil production technology from palm oil by a combination of the partial hydrolysis and partial esterification reaction using immobilized biocatalyst in a hollow fiber membrane bioreactor.
The result of partial hydrolysis is used to be the feed of partial esterification reaction to increase the yield of DAG oil. The effect of configuration of oil flow direction in the synthesis process is not significant. Higher enzyme concentration increased the yield of DAG oil produced. Through the study of oil flow rate, obtained that by using 5 mg/mL biocatalyst concentration and 0,05 mL/s as optimum flow rate can produce 79,19% DAG Oil purity.
"
Depok: Fakultas Teknik Universitas Indonesia, 2010
S51948
UI - Skripsi Open  Universitas Indonesia Library
cover
Teguh Budi Santoso
"Biodiesel merupakan bahan bakar alternatif yang aplikasinya pada mesin masih terkendala karena memiliki keterbatasan diantaranya stabilitas oksidasi yang rendah sehingga berpengaruh kepada kualitas penyimpanan biodiesel. Salah satu solusi untuk mengatasi masalah ini adalah dengan proses hidrogenasi parsial. Pada proses hidrogenasi parsial, FAME direaksikan dengan hidrogen dan katalis untuk memecah ikatan tak jenuh. Penggunaan katalis nikel yang disangga pada alumina (Ni/Al2O3) lebih menguntungkan karena harganya yang murah dan mempunyai aktivitas katalitik yang tinggi. Reaksi hidrogenasi parsial dilakukan pada reaktor trickle bed dengan hidrogen pada fase gas, katalis pada fase padat, dan FAME pada fase cair. Penggunaan reaktor jenis ini memiliki kelebihan yaitu jatuh tekanan yang rendah (pressure drop), kehilangan katalis yang rendah, tidak memiliki elemen yang bergerak, dan biaya perawatan yang rendah. Penelitian ini bertujuan untuk merancang sistem reaktor tiga fasa dan uji kinerja reaktor trickle bed untuk hidrogenasi parsial Biodiesel. Hasil penelitian menunjukkan bahwa reaktor trickle bed berhasil memecah ikatan tak jenuh ganda (C19:2) pada rantai ikatan FAME menjadi ikatan tak jenuh tunggal (C19:1) dan ikatan jenuh (C19:0). Konversi biodiesel terbesar (8,93 %) diperoleh dengan kondisi operasi: tekanan hidrogen 7 bar, laju alir hidrogen 250 ml/menit dan laju alir biodiesel 0,667 ml/menit.

Biodiesel is an alternative fuel whose application to the engine is still constrained because it has limitations including low oxidation stability which affects the quality of biodiesel storage. One solution to overcome this problem is the partial hydrogenation. In the partial hydrogenation, FAME is reacted with hydrogen and a catalyst to break down unsaturated bonds. The use of nickel catalyst supported on alumina (Ni/Al2O3) is more advantageous because the price is low and has high catalytic activity. Partial hydrogenation reactions were carried out on trickle bed reactor. The use of this type of reactor has advantages such as low catalyst loss, no moving elements, and low maintenance costs. The research investigated partial hydrogenation of fatty acid methyl esters in a trickle-bed reactor. The result showed that the partial hydrogenation of polyunsaturated FAMEs in a trickle bed reactor had break down the polyunsaturated bond (C19:2) on the FAME into a monounsaturated bond (C19:1) and saturated bond (C19:0) and the best conversion of polyunsaturated FAMEs is 8.93% achieved with reaction condition: H2 pressure 7 bar, H2 flow rate 250 ml/min and biodiesel flow rate 0.667 ml/min."
Depok: Fakultas Teknik Universitas Indonesia, 2019
T53230
UI - Tesis Membership  Universitas Indonesia Library
cover
Muhammad Rafli
"Gas metana merupakan salah satu komponen terbesar dalam biogas yang dapat dikonversi menjadi metanol melalui reaksi oksidasi parsial. Reaksi oksidasi parsial bio-metana sebagai sumber metana dengan menggunakan katalis heterogen ZSM-5 sintesis termodifikasi oksida logam besi. Penambahan logam diharapkan dapat menghasilkan selektivitas yang lebih tinggi terhadap konversi metana menjadi metanol.
Pada penelitian ini, katalis ZSM-5 alam maupun sintetik disintesis dengan metode double template menggunakan primary template TPAOH sebagai pengarah framework MFI, serta secondary template yaitu dimethyldiallyl ammonium chloride acrylamide copolymer (PDD-AM) sebagai pengarah struktur mesopori. Katalis Fe2O3/ZSM-5 alam dan sintetik yang telah disintesis, dianalisa menggunakan XRD, SEM, BET, dan FTIR. Karakterisasi dengan XRF juga dilakukan untuk mengetahui kadar %loading oksida logam besi pada katalis ZSM-5.
Uji aplikasi masing-masing katalis terhadap adsorpsi menggunakan biogas sebagai sumber metana dilakukan dalam atmospheric fixed batch reactor dengan perbandingan feed CH4(biogas):N2 0,75:2. Reaksi dilakukan pada suhu 150oC dengan waktu 120 menit dengan variasi jumlah katalis dan melakukan reaksi menggunakan katalis regenerasi. Produk hasil reaksi dari masing-masing katalis dianalisa dengan GC-FID untuk mengetahui %yield metanol yang terbentuk.

Methane gas is one of abundant component in biogas that is common to be converted into methanol through partial oxidation reaction. Partial oxidation reaction of bio-methane uses methane as its source along with the utilization of modified iron oxide with natural and/or synthetic ZSM-5 as heterogeneous catalyst. Based on recent research showed that hierarchical ZSM-5 that was modified with iron oxide produced optimum % yield of methanol in bio-methane partial oxidation reaction (Triputrananda, 2018). Addition or loading of iron is expected to produce higher selectivity towards methane conversion into methanol. Aside of that, optimization was done with variation of pore size to determine the type of catalyst and its corresponds with optimum partial oxidation conversion output.
In this research, natural and/or ZSM-5 catalyst were synthesized in double template method with TPAOH as its primary template that directed to MFI framework, PDDAM as its secondary template that directed mesoporous structure. Natural and/or synthetic Fe2O3/ZSM-5 catalyst were synthesized and further be analyzed with XRD, SEM, BET, and FTIR. Characterizations of XRF was done in order to obtain loading percentage of iron oxide into the ZSM-5 catalyst.
The application were done in each variation of catalyst towards adsorption with biogas as methane source that was done in atmospheric fixed batch reactor with ratio of CH4(biogas):N2 0,75:2 feed. Reactions were done under temperature of 150oC with 120 minutes duration, alongside with amount of variation on catalyst and reaction with regenerated catalyst. Products obtained from each catalyst were analyzed with GC-FID to determine % of conversion from each products obtained.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Fillia Rezki Fajri
"Industri air limbah wine menghasilkan air limbah yang memiliki karakteristik tinggi kandungan organik serta pH bersifat asam. Pengolahan konvensional dalam mengolah air limbah industri wine sangat kompleks, sehingga membutuhkan penanganan secara khusus. Saat ini, terdapat teknologi pengolahan yang sesuai dengan karakteristik air limbah wine yaitu proses oksidasi Fenton dan teknologi membran. Teknologi membran memiliki ukuran pori yang berbeda-beda, saat ini banyak pemanfaatan membran jenis nanofiltrasi dalam pengaplikasian pengolahan limbah industri. Membran nanofiltrasi memiliki kemampuan yang mirip dengan reverse osmosis yang dapat menyisihkan kandungan bahan organik serta anorganik. Proses filtrasi pada penelitian ini dilakukan secara konstan fluks dengan variasi fluks 40 LMH, 50 LMH, dan 60 LMH. Hasil penyisihan COD, besi, dan warna pada fluks 40 LMH, 50 LMH, dan 60 LMH secara berturut-turut adalah 64% ; 93%; 100%, 75%; 93% ; 100%, dan 76%; 94%; 100%. Hasil penelitian menunjukkan bahwa efisiensi penyisihan paling efektif pada fluks 60 LMH. Namun fluks 60 LMH rentan mengalami fouling yang menyebabkan permeabilitas menurun seiring berjalannya waktu. Selain itu, reversibility pada kondisi pengoperasian fluks 60 LMH didominasi oleh jenis irreversible fouling, sehingga proses mechanical backwash tidak cukup untuk mengembalikan performa membran dan membutuhkan chemical cleaning.

The wine wastewater industry produces wastewater that is characterized by high organic content and an acidic pH. Conventional processing of wine industry wastewater is very complex, so it requires special handling. Currently, there are processing technologies that suit the characteristics of wine wastewater, namely the Fenton oxidation process and membrane technology. Membrane technology has different pore sizes, currently many nanofiltration type membranes are used in industrial waste processing applications. Nanofiltration membranes have capabilities similar to reverse osmosis which can remove organic and inorganic materials. The filtration process in this study was carried out at constant flux with flux variations of 40 LMH, 50 LMH, and 60 LMH. The COD, iron and color removal results at fluxes of 40 LMH, 50 LMH and 60 LMH respectively were 64%; 93%; 100%, 75%; 93% ; 100%, and 76%; 94%; 100%. The results showed that the removal efficiency was most effective at a flux of 60 LMH. However, 60 LMH flux is susceptible to fouling which causes permeability to decrease over time. Apart from that, reversibility at 60 LMH flux operating conditions is dominated by irreversible fouling, so the mechanical backwash process is not enough to restore membrane performance and requires chemical cleaning."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ghina Zhahirah Dadona
"Teknologi pengolahan air limbah wine terdapat banyak alternatif dan menggunakan berbagai kombinasi pengolahan untuk menghasilkan kualitas air yang lebih baik. Pada penelitian ini, dilakukan kombinasi pengolahan menggunakan Fenton heterogen dengan katalis fly ash serta membran ultrafiltrasi. Penelitian berorientasi pada performa membran ceramic UF sebagai teknologi pengolahan filtrasi. Performa yang ditinjau khususnya pada mekanisme serta efisiensi penyisihan COD, warna, UV274, dan besi serta pengaruhnya terhadap variasi fluks (80 LMH, 100 LMH, 120 LMH). Eksperimen yang dilakukan dalam skala laboratorium menggunakan membran UF berbentuk flat sheet material ceramic dengan luas permukaan sebesar 13,1 cm2 yang akan difiltrasi dengan konsep multicycle sebanyak 8 siklus. Mekanisme fouling yang terbentuk dan keterkaitannya terhadap efisiensi penyisihan parameter menunjukkan hasil yang optimal pada fluks yang lebih tinggi. Pada keseluruhan eksperimen, didapatkan penurunan performa yang diindikasikan dari penurunan normalized permeability serta peningkatan besar energi (tekanan pompa) yang tidak lebih dari 35%. Sedangkan itu, didapatkan penurunan penyisihan keseluruhan eksperimen pada parameter warna >79%, COD >66%, dan besi >77%. Sedangkan itu, untuk parameter UV274 tidak efektif tersisihkan oleh membran ceramic UF, dengan maksimal penyisihan hanya berkisar pada 13%. Penggunaan fluks 100 LMH cenderung lebih optimal dengan mempertimbangkan besar tekanan (pompa) yang tepat serta mekanisme fouling yang lebih stabil dengan efisiensi penyisihan yang lebih baik.

There are many alternative wine wastewater treatment technologies and various treatment combinations are used to produce better water quality. In this study, a combination of treatment using heterogeneous Fenton with fly ash catalyst and ultrafiltration membrane was conducted. The research was oriented towards the performance of ceramic UF membrane as filtration treatment technology. The performance reviewed was specifically on the mechanism and efficiency of COD, colour, UV274, and iron removal and its effect on flux variations (80 LMH, 100 LMH, 120 LMH). Experiments were conducted on a laboratory scale using a UF membrane in the form of a flat sheet of ceramic material with a surface area of 13.1 cm2 which will be filtered with the concept of multicycle for 8 cycles. The fouling mechanism formed and its relationship to the parameter removal efficiency showed optimal results at higher fluxes. In all experiments, there was a decrease in performance indicated by a decrease in normalised permeability and an increase in energy (pump pressure) of no more than 35%. Meanwhile, a decrease in the overall experimental removal was obtained for colour parameters >79%, COD >66%, and iron >77%. Meanwhile, the UV274 parameter was not effectively removed by the ceramic UF membrane, with a maximum removal of only around 13%. The use of 100 LMH flux tends to be more optimal by considering the right amount of pressure (pump) and a more stable fouling mechanism with better removal efficiency."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muhamad Faisal
"ZSM-5 telah berhasil disintesis melalui metode hidrotermal dari mineral alam zeolit alam Bayat dan kaolin Bangka sebagai sumber alumina dan silika, TPAOH sebagai agen pengarah struktur MFI dan PDDA-M sebagai pengarah mesopori. ZSM-5 kemudian dimodifikasi permukaannya dengan oksida logam Fe dan Co melalui metode impregnasi basah untuk meningkatkan aktivitas katalitiknya pada reaksi oksidasi parsial metana. Modifikasi dengan oksida logam ini juga dilakukan untuk ZSM-5 sintetik sebagai pembanding dalam aktivitas katalitiknya. ZSM-5 alam dan ZSM-5 sintetik termodifikasi oksida logam dikarakterisasi dengan instrumen FTIR, XRD, SEM-EDX, surface area analyzer dan XPS untuk mengetahui pengaruh modifikasi permukaan terhadap struktur, morfologi dan aktivitas katalitiknya. Analisis komposisi unsur dari ZSM-5 alam terimpregnasi oksida Fe dan Co menunjukkan % loading Fe dan Co berturut-turut sebesar 2,37% dan 1,78%. Hasil pengujian isoterm adsorpsi menunjukkan baik ZSM-5 alam maupun ZSM-5 alam terimpregnasi oksida logam Fe dan Co memiliki kurva tipe IV H4 yang merupakan kurva ciri khas material berpori hirarki. Analisis XPS menunjukkan spesi oksida logam Fe dan Co yang menempel pada ZSM-5 berturut-turut adalah Fe2O3 dan Co3O4. Hasil uji analisis kandungan gas menggunakan GC-TCD menunjukkan berkurangnya mol metana setelah reaksi yang menandakan metana telah terkonversi menjadi metanol dan formaldehida yang terlihat dari puncak kromatogram GC-FID. Hasil analisis produk dengan GC-FID menunjukkan reaksi oksidasi parsial metana menggunakan Fe/ZSM-5 menghasilkan formaldehida dan menggunakan Co/ZSM-5 menghasilkan metanol dan formaldehida.

ZSM-5 has been successfully synthesized through hydrothermal method using Bangka Kaolin and Bayat Natural Zeolite as the precursors, TPAOH as MFI-structure directing agent; PDDA-M as mesopore directing agent. Furthermore, the surface of ZSM-5 was impregnated with metal oxide of Fe and Co to improve its catalytic performance through partial oxidation of methane reaction. As comparison, ZSM-5 synthesized from pro analysis precursors was also impregnated with metal oxide of Fe and Co and tested through the reaction. Metal oxide of Fe and Co impregnated ZSM-5 were characterized with XRD, SEM-EDS, XPS and SAA-BET instruments to see the effect of impregnation to the structure and characteristic of both materials. Analysis of the elemental composition of Fe/ and Co/ZSM-5 was 2,37% and 1,78% respectively. The N2 isotherm adsorption curve shows a type IV H4 indicates that the materials has hierarchical characteristic. XPS analysis show the Fe and Co oxide that impregnated to ZSM-5 is Fe2O3 and Co3O4. GC-TCD analysis show there is a decreases of methane mol after reaction indicates that the methane has been converted. GC-FID analysis show that the partial oxidation of methane using Fe/ZSM-5 yielded formaldehyde whereas for Co/ZSM-5 yielded methanol and formaldehyde."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2020
T54844
UI - Tesis Membership  Universitas Indonesia Library
cover
Arbhyando Tri Putrananda
"Penelitian ini dilakukan konversi gas metana yang berasal dari biogas bio-metana menjadi metanol dengan bantuan katalis ZSM-5 hirarki termodifikasi oksida logam kobalt dan besi. Material ZSM-5 hirarki disintesis dengan metode double template menggunakan TPAOH dan PDD-AM sebagai secondary template. Analisa dengan SEM-EDS diperoleh morfologi material bentuk coffin yang merupakan ciri khas material ZSM-5. Hasil analisa dengan FTIR dan XRD juga menunjukkan bahwa puncak dan pola difraksi material ZSM-5 hasil sintesis memiliki kesamaan dengan ZSM-5 standar. Impregnasi oksida logam kobalt dan besi ke dalam material ZSM-5 diperoleh loading sebesar 2,1-2,5 dengan analisa menggunakan instrumen AAS.
Hasil analisa dengan XPS menunjukkan bahwa oksida logam kobalt dan besi yang terbentuk adalah Co3O4, dan Fe2O3 pada material ZSM-5. Uji aplikasi oksidasi parsial bio-metana menjadi metanol dilakukan dalam atmospheric fixed batch reactor dengan perbandingan bio-metana:N2 sebesar 0,2:2 bar. Hasil uji aplikasi dengan menggunakan bio-metana diperoleh katalis Fe2O3/ZSM-5 hirarki memiliki yield metanol tertinggi sebesar 17,61. Besarnya kandungan oksigen pada bio-metana dapat meningkatkan yield metanol pada reaksi katalisis oksidasi parsial metana menjadi metanol.

This study aimed to converted methane gas from biogas bio methane to methanol using modified cobalt and iron metal oxide hierarchical ZSM 5. Hierarchical ZSM 5 synthesized by double template methods using TPAOH and PDD AM as the secondary template. SEM EDS analysis shows the morphology of coffin shaped which is the characteristic of ZSM 5 material. The results of FTIR and XRD analysis also show that peak and diffraction pattern of ZSM 5 synthesized material have in common with standard of ZSM 5. The impregnation of cobalt and iron metal oxide into ZSM 5 material obtained by loading of 2,1 2,4 using AAS instrument.
The results of XPS analysis show that cobalt and iron metal oxide formed are Co3O4 and Fe2O3 in ZSM 5 material. The partial oxidation of bio methane to methanol is carried out in an atmospheric fixed batch reactor with a bio methane N2 ratio of 0,2 2 bar. The results of application using bio methane show the hierarchical Fe2O3 ZSM 5 catalyst has the highest methanol yield of 17,61. The amount of oxygen concentration in bio methane can increase the yield of methanol in partial oxidation of bio methane to methanol.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Danika Nurranalya Putri
"Metana adalah salah satu dari gas rumah kaca yang berkontribusi sekitar 19%. Metana memiliki potensi pemanasan global 28 kali lebih besar dibandingkan gas karbondioksida. Sehingga, diperlukan suatu metode untuk mengonversi metana menjadi bahan kimia lain yang bermanfaat. Salah satunya adalah dengan oksidasi parsial metana menjadi metanol. Pada penelitian ini, Co3O4/ZSM-5 disintesis melalui dua metode, yaitu Bottom Up dan Top Down, lalu diimpregnasi dengan oksida kobalt dengan variasi persen loading sebesar 2,5, 5, dan 10%. Co3O4/ZSM-5 Bottom Up dan Top Down dikarakterisasi dengan XRD, FTIR, BET, SEM, dan XRF. Katalis yang diperoleh digunakan untuk reaksi oksidasi parsial metana menggunakan batch reactor. Reaksi dilakukan dengan perbandingan feed CH4 : N2 sebesar 0,75 bar : 2 bar, dengan suhu 150oC dan waktu reaksi selama 60 menit. Hasil reaksi menunjukkan bahwa Co3O4/ZSM-5 Bottom Up dengan persen loading 5% menghasilkan persen yield metanol terbesar, yaitu 62,08%. Sedangkan Co3O4/ZSM-5 Top Down dengan persen loading 2,5% menghasilkan persen yield metanol sebesar 0,016%. Variasi waktu dilakukan terhadap Co3O4/ZSM-5 5% Bottom Up dan Co3O4/ZSM-5 2,5% Top Down. Hasil yang diperoleh berupa formaldehida atau tidak terbentuk produk sama sekali, sehingga diketahui bahwa waktu reaksi yang optimum adalah 60 menit, dengan persen loading logam optimum sebesar 5% untuk metode Bottom Up dan 2,5% untuk metode Top Down.

Methane is one of the greenhouse gases that contributes about 19%. Methane has a global warming potential 28 times greater than carbon dioxide gas. Thus, a method is needed to convert methane into other useful chemicals. One of them is by partial oxidation of methane to methanol. In this study, Co3O4/ZSM-5 was synthesized through two methods, namely Bottom Up and Top Down, then impregnated with cobalt oxide with variations in percent loading of 2,5, 5, and 10%. Co3O4/ZSM-5 Bottom Up and Top Down characterized by XRD, FTIR, BET, SEM, and XRF. The catalyst obtained was used for the partial oxidation of methane using a batch reactor with ratio of feed CH4 : N2 of 0.75 bar: 2 bar, with a temperature of 150o and a reaction time of 60 minutes. The reaction results show that Co3O4/ZSM-5 Bottom Up with a loading 5% produces the largest percentage yield, which is 62.08%. Meanwhile, Co3O4/ZSM-5 Top Down with a loading 2.5% produces yield of 0.016%. Time variations were carried out on Co3O4/ZSM-5 5% Bottom Up and Co3O4/ZSM-5 2.5% Top Down. The results obtained are formaldehyde or no product is formed, so it is known that the optimum reaction time is 60 minutes, with the optimum metal loading percent of 5% for the Bottom Up method and 2.5% for the Top Down method."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
<<   1 2 3 4 5 6 7 8 9 10   >>