Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 170399 dokumen yang sesuai dengan query
cover
Kartissa Pangesti
"Menganalisis sitotoksisitas TAD SS setelah paparan tiga jenis larutan kumur yang dilihat melalui parameter reaktivitas dan viabilitas sel fibroblast BHK-21. Metode: 28 unit TAD SS dibagi menjadi masing-masing 7 unit TAD dalam 4 kelompok larutan kumur (sodium fluoride 0.2%, povidone iodine 1%, kitosan 1.5%, akuades) dan direndam selama 90 hari. Elusi TAD SS dalam larutan kumur kemudian dimasukkan ke dalam kultur sel fibroblast BHK-21 dan diinkubasi selama 24 jam. Reaktivitas dianalisis dengan mikroskop inverted-light dan reliabilitasnya diuji dengan ICC serta diuji secara statistik dengan independent T-test. Viabilitas dilakukan dengan metode MTT Assay dan dianalisis secara statistik dengan independent T-test. Hasil: Sel fibroblast BHK-21 menunjukkan perbedaan reaktivitas yang bermakna (p<0.05) setelah paparan elusi TAD SS dalam larutan kumur povidone iodine dan kitosan dibanding larutan povidone iodine dan kitosan tanpa TAD SS. Uji viabilitas menunjukkan perbedaan bermakna (p<0.05) setelah paparan elusi TAD SS dalam larutan kumur povidone iodine dibanding larutan povidone iodine saja tanpa TAD SS. Reaktivitas sel fibroblast BHK-21 pada kelompok yang terpapar larutan fluoride dan akuades tidak berbeda bermakna (p>0.05) dibanding larutan fluoride dan akuades tanpa TAD SS. Viabilitas sel fibroblast BHK-21 pada kelompok yang terpapar larutan fluoride dan akuades tidak berbeda bermakna (p>0.05) dibanding kelompok larutan fluoride dan akuades tanpa TAD SS. Kesimpulan: Pasien ortodonti dengan TAD SS dapat dianjurkan menggunakan larutan kumur kitosan dengan kadar lebih rendah atau akuades. Larutan kumur fluoride tidak dianjurkan untuk diberikan pada pasien ortodonti dengan TAD SS. Larutan povidone iodine sebaiknya tidak digunakan secara terus menerus untuk memberi waktu bagi revitalisasi sel.

Analyzing the cytotoxicity of SS TAD after exposure to three types of mouthwash seen through the parameters of reactivity and viability of BHK-21 fibroblast cells. Methods: 28 units of SS TAD were divided into 7 units each of TAD in 4 groups of mouthwash (sodium fluoride 0.2%, povidone iodine 1%, chitosan 1.5%, aquadest) and immersed for 90 days. The elution of SS TAD in mouthwash was then fed into BHK-21 fibroblast cell culture and incubated for 24 hours. Reactivity was analyzed with an inverted-light microscope and reliability was tested with ICC also statistically tested with an independent T-test. Viability was performed using MTT Assay and statistically analyzed with an independent T-test. Results: BHK-21 fibroblast cells showed significant differences in reactivity (p<0.05) after exposure to TAD SS elution in povidone iodine and chitosan mouthwash compared to its solution groups without TAD SS. Viability test showed significant differences (p<0.05) after exposure to TAD SS elution in povidone iodine mouthwash compared to povidone iodine without TAD SS. The reactivity of BHK-21 fibroblast cells exposed to fluoride and aquadest was not significantly different (p>0.05) compared to its solution groups without TAD SS. The viability of BHK-21 fibroblast cells exposed to fluoride and aquadest did not significantly different compared to its solution groups without TAD SS. Conclusions : Orthodontic patients with TAD SS may be recommended to use lower levels of chitosan mouthwash or aquadest. Fluoride mouthwash is not recommended to be given to orthodontic patients with TAD SS. Povidone iodine solution should not be used continuosly to give time for cell revitalization"
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2023
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Refnaldi
"Tujuan dari studi ini adalah mengevaluasi perubahan-perubahan dalam struktur mikro dan sifat mekanis dari baja tahan karat 304L dan 3l6L dibawah pengelasan perbaikan berulang. Perubahan-perubahan dari kedua material tersebut kemudian diperbandingkan satu sama lain. Pengelasan dan pengelasan perbaikan dilaksanakan dengan GTAW. Proses pengelasan GTAW dilaksanakan menggunakan logam pengisi ER308L untuk baja tahan karat 304L dan ER3l6L untuk baja tahan karat 316L. Spesimen dari logam dasar dan kondisi berbeda dari perbaikan GTAW dipelajari dengan melihat perubahan struktur mikro, komposisi kimia dari fase-fase, ukuran butir dalam daerah terpengaruh panas dan efek terhadap sifat mekanis. Struktur miko diinvestigasi menggunakan mikroskop optik dan scanning electron microscopy (SEM). Komposisi kimia dari base material ditentukan dengat optical emission specffometer. Komposisi kimia dari inti las, daerah terpengaruh panas dan logam induk ditentukan dengan XRF Analyzer. Komposisi kimia dari fase-fase ditentukan dengan Energt Dispersive X' ray Analysis (EDAX). Pengujian mekanik yang dilakukan uji tarik, kekuatan impak Charpy-V, dan uji keras mito Vickers. Permttkaan patahan diamati dengan foto makro dan detail morfologi permukaan patahan pada awal dan tengah atau ujung permukaan patahan diinvestigasi dengan scanning electron microscopy (SEM). Kekerasan dari daerah terpengaruh panas menunrn sesuai dengan peningkatan jumlah perbaikan. Secara umum peningkatan dalam kekuatan tarik (UTS) terjadi dalam pengelasan. Pada perbaikan pertama suatu penurunan bertahap dalam kekuatan Tarik (UTS) terjadi tetapi nilai kekuatan tarik (UTS) tidak kurang dat', base metal. Pengxangan signifikan dalam kekuatan impak charpy-V dengan jumlah perbaikan las diamati dengan lokasi takikan di daerah terpengaruh panas. Perubahan-perubahan yang sama terhadap struktur miko dan sifat mekanis terjadi pada kedua tipe baja tahan karat tersebut. Perbedaannya adalah untuk kekuatan tarik dan kekuatan impak pada hasil pengelasan baja tahan karat 304L lebih baik daripada 316L.

The purpose of this study is to evaluate changes in the micro structural and mechanical properties of stainless steel 304L and 3l6L under repeated repair welding. The changes of both of material then will be in comparation to each other. The welding and the repair welding were conducted by gas tungsten arc welding (GTAW). The GTAW welding process w.rs performed using ER308L filler metals for stainless steel 304L and ER3I6L filler metals for stainless steel 316L. Specimen of the base metal and different conditions of gas tungsten arc welding repairs were studied by looking in the micro structural changes, the chemical composition of the phases, the grarn size (in the heat affected zone) and the effect on the mechanical properties. The microstructure was investigated using optical microscopy (OM) and scanning electron microscopy (SEM). The chemical composition of the base material was determined using optical emission spectrometer. The chemical composition of weld metal, heat affected zone and base metal was determined using XRF Analyzer. The chemical composition of the phases was determined using energy dispersive X-ray Analysis (EDAX). Mechanical testing consist of tensile tests, Charpy-V impact resistance and Vickers hardness tests were conducted. Detail of fracture surface morphologies in beginning and centre or end of fracture was investigated using scanning electron microscopy (SEM). Hardness of the heat affected zone decreased as the number of repairs increased. Generally an increase in the ultimate tensile strength (UTS) occuned with welding. At the first repair, a gradual decrease in UTS occurred but the values of UTS were not less than values of the base metal. Signif,rcant reduction in Charpy-V impact resistance with the number of weld repairs were observed when the notch location was in the HAZ. T"be similar changes in the micro structural and mechanical properties occured in both of type of stainless steel. The difference were for the values ofUTS and Charpy-V impact resistance of welding specimen of stainless steel 304L more tlan values of stainless steel 316L."
Depok: Fakultas Teknik Universitas Indonesia, 2015
T44258
UI - Tesis Membership  Universitas Indonesia Library
cover
Angga Fauzian
"Tungsten Inert Gas (TIG) adalah proses pengelasan dimana busur listrik ditimbulkan oleh elektroda tungsten dengan benda kerja dan daerah pengelasannya dilindungi oleh gas pelindung. Sejak pertama kali ditemukan, TIG sudah menjadi bagian penting dalam industri manufaktur. Pengelasan ini banyak diaplikasikan pada baja stainless steel, alumunium, logam reaktif seperti magnesium dan titanium. Karena banyaknya aplikasi pengelasan TIG, pada studi kali ini dilakukan sebuah simulasi pengelasan pada plat stainless steel untuk memprediksi lebarnya manik las yang terbentuk dan kedalaman penetrasi pengelasan dengan memvariasikan besarnya arus yaitu 80, 90, dan 100 A dan besarnya kecepatan pengelasan yaitu 2, 3, dan 4 mm/s. Simulasi pengelasan menunjukan hasil yang hampir sama dengan pengelasan secara eksperimen, dimana untuk lebar manik atas pada variasi arus dan kecepatan didapatkan error rata-rata berturut-turut 8.3% dan 6.7%, dan untuk lebar manik bawah pada variasi arus dan kecepatan didapatkan error rata-rata bertururt-turut 4.9% dan 3.0%. Sementara, untuk penetrasi pengelasan error rata-ratanya 0%.

Tungsten Inert Gas (TIG) welding is a process which an electric arc generated by the tungsten electrode to the workpiece and the welding area protected by a protective gas. First, since TIG had been discover, it become an important part in manufacturing industry. TIG is widely applied to stainless steel, aluminum, reactive metals such as magnesium and titanium. Therefore, this study carried out a simulation of welding in stainless steel plate to predict the bead width and the depth of penetration were formed by varying the welding current as 80, 90, and 100 A and varying the welding speed as 2, 3, and 4 mm/s. Welding simulation showed almost the same results with the experimental welding, where for the top bead width over the current and velocity variations obtained an average error of 8.3 % and 6.7 % respectively. And for the back bead width over the current and velocity variations obtained average error of 4.9 % and 3.0 % respectively. While, for the depth of penetration obtained an average error of 0 %."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S53394
UI - Skripsi Membership  Universitas Indonesia Library
cover
Hasbi Fahada
"Salah satu metode untuk menentukan konstanta-konstanta elastisitas efektif material IN-519 (cast austenitic stainless steel) adalah dengan menggunakan teknik potongan kubus (cube cutting method) dan transmisi gelombang ultrasonik. Akan tetapi dimensi kubus dengan ukuran 10x10x10 mm menjadi salah satu kendala dalam teknis pengukuran, karena sebagian besar probe ultrasonik memiliki ukuran penampang yang lebih besar dari sampel. Oleh karena itu, tingkat efektifitas nilai hasil pengukuranya perlu diketahui dengan menentukan nilai deviasi pengukuran konstanta elastisitas dan atenuasi gelombang ultrasonik dengan frekuensi 1, 2,25, 4, dan 5 MHz pada kubus dengan sampel pembanding (pelat). Nilai deviasi paling besar terjadi pada pengukuran konstanta C33 dan atenuasi dengan frekuensi 1 MHz. Kemudian hasil penelitian menunjukan bahwa semakin besar frekuensi pengukuran, maka nilai konstanta elastisitas semakin kecil, dan nilai atenuasi semakin besar. Pengujian pada sampel hasil solution anneal memiliki nilai konstanta-kontanta elastisitas yang lebih besar dan atenuasi yang lebih kecil dibandingkan dengan sampel non-anneal. Dan konstanta¬konstanta elastisitas baik pada sampel annealed maupun sampel non-anneal diprediksikan memiliki nilai penyimpangan pengukuran kurang lebih sebesar 31 % terhadap hasil pengujian tarik.

One of the methods for effective elastic constants determining in IN-519 material (cast austenitic stainless steel) is using cube cutting method and ultrasonic wave transmission. However, dimension of cubes with a minimum size of 10x10x10 mm become one of the obstacles in the technical measurement, because most of the ultrasonic probe has a larger cross-sectional size of the sample. Therefore, the level of effectiveness measurement results need to be identified by determining the deviation of the measurement of elasticity constants and the attenuation of ultrasonic waves with a frequency of 1, 2.25, 4, and 5 MHz on the cube with the comparison sample (plate). Greatest deviations occur at measurement of C33 and attenuation with frequency of 1 MHz. The results showed that the greater frequency of measurements the value of the constant elasticity is smaller, and the greater the attenuation value. Tests on annealed samples has a greater elasticity constant value and the attenuation is smaller than the non-anneal samples. And elastic constant in both annealed samples and non-anneal measurement are predicted has a deviation value of approximately 31% of the tensile test results. "
Depok: Fakultas Teknik Universitas Indonesia, 2011
S789
UI - Skripsi Open  Universitas Indonesia Library
cover
Mohammad Fadli
"Variasi parameter pengelasan terhadap ketidakseimbangan struktur mikro lasan baja tahan karat SAF 2707 hiperduplek dan pengaruhnya terhadap sifat mekanik telah dipelajari. Pembatasan masukan panas dan penambahan gas nitrogen ke dalam gas pelindung argon merupakan cara yang efektif untuk mengontrol struktur mikro lasan baja tahan karat SAF 2707 hiperduplek sehingga masih meninggalkan sifatnya yang sangat baik.
Dari hasil pengamatan menunjukkan bahwa lebar kampuh las dan kedalaman penetrasi lasan akan meningkat seiring peningkatan masukan panas dan penambahan gas nitrogen dalam gas pelindung argon. Selain itu, peningkatan masukan panas akan menurunkan fraksi volume ferit. Begitu pula dengan penambahan gas nitrogen pada gas pelindung argon akan menurunkan fraksi volume ferit.
Pada penelitian ini, masukan panas dibatasi pada rentang 0.3 kJ/mm - 1.4 kJ/mm dan menghasilkan fraksi volume ferit pada rentang 31% - 53% pada kampuh las dan 48% - 70% pada daerah terpengaruh panas (HAZ). Tidak ditemukan fasa intermetalik pada struktur mikronya. Kekerasan meningkat seiring meningkatnya fraksi volume ferit.

The variation of welding parameters on the unbalance microstructure of SAF 2707 hyperduplex stainless steel weldments and its effects on the mechanical properties has been studied. Limiting the heat input and introducing nitrogen gas into argon shielding gas are the effective way to control the microstructure of SAF 2707 hyperduplex stainless steel weldments in order to maintain its excellent properties.
From achieved result, the width of weld bead and the depth of weld penetration increased as heat input increased and as well as increasing nitrogen gas into the argon shielding gas. In addition, as heat input increased, the volume fraction of ferrite decreased. Similarly, as nitrogen gas increased into the argon shielding gas, the volume fraction of ferrite decreased.
In this research, the heat input was limited in the range 0.3 kJ/mm - 1.4 kJ/mm and produced volume fraction of ferrite in the range 31% - 53% on the weld metal dan 48% - 70% on the HAZ. No intermetallic phase found on its microstructure. The hardness increased as volume fraction of ferrite increased.
"
Depok: Fakultas Teknik Universitas Indonesia, 2012
S42334
UI - Skripsi Open  Universitas Indonesia Library
cover
Mohammad Badaruddin
"Tujuan penelitian ini adalah untuk mengetahui pengaruh prestrain terhadap perilaku korosi retak tegang stainless steel AISI 304 dalam larutan H2SO4 konsentrasi 10% dengan pembebanan kantilever statis (ASTM E-1681). Prestrain dilakukan dengan meregangkan spesimen hingga mencapai regangan merata 5% dan 10% diatas tegangan luluh bahan, menggunakan servopulser UTM 9506 dengan kontrol kecepatan 0,3 mm/sec.
Hasil pengujian menunjukan bahwa spesimen dengan 5% prestrain lebih cepat mengalami kegagalan daripada spesimen 10% prestrain dan tanpa prestrain. Hal ini disebabkan menurunnya keuletan dan periode inkubasi yang singkat. Perubahan defleksi hanya dapat diamati pada pembebanan 20% tegangan luluh bahan. Retak intergranular ditemukan pada spesimen 10% prestrain pada pembebanan statis 616 MPa. Sedangkan pada specimen 10% prestrain ditemukan retak transgranular pada pembebanan statis 554,4 MPa. Retak kombinasi ditemukan pada specimen 5% prestrain pada pembebanan statis 369,6 MPa. Semakin tinggi densitas dislokasi pada lapisan permukaan akibat deformasi plastis, semakin sulit difusi hidrogen pada ujung retak. Konsekuensinya, periode inkubasi dapat diperlama.

Stress Corrosion Cracking Behavior of Stainless Steel 304 in the Sulfuric Acid Environment Due to Prestrain. The aim of research is to investigate the effect of prestrain on the stress corossion cracking behavior of AISI 304 stainless steel in the sulfuric acid of 10% concentration under the static cantilever loading according to ASTM E-1681 standart. The specimen of 304 Stainless steel was strain up over the yield strength until reaching the uniform strain of 5% and 10% using servopulser UTM 9506 under the displacement control of 0,3 mm/sec.
The results of test show that the prestrain of 5% specimen is faster failure than both of the prestrain of 10% and unprestrain specimen. It was caused by both of the decrease of ductility and the short incubation period. The change of deflection could be only recorded under the loading 20% of yield strength. Intergranular crack was the prestrain of 10% specimen under the static loading of 616 MPa. Whereas, for the prestrain of 10% specimen transgranular crack was found under the static loading of 554,4 MPa. The prestrain of 5% specimen was mixed crack under the static loading of 369.6 MPa. Higher dislocation density on the layer surface due to plastic deformation with increasing the percentage of pre-strain, so more difficult hydrogen diffused into the crack tip. Consequently, The incubation period can be prolonged."
Depok: Lembaga Penelitian Universitas Indonesia, 2006
AJ-Pdf
Artikel Jurnal  Universitas Indonesia Library
cover
Cobb, Harold M.
"?Chemical engineers designing, operating and maintaining their ever-expanding industry during the second half of the 20th century relied heavily on stainless steels. Few, however, were familiar with or understood its history. This treatise satisfies that shortcoming in an interesting, readable manner. The ?Timeline? alone is a remarkable presentation.? Richard Leonard, retired, Hercules, Inc."
Materials Park, Ohio: ASM International, 2010
e20451673
eBooks  Universitas Indonesia Library
cover
I Nyoman Jujur
"The type of stainless steel that is most commonly used in bone implants is austenitic 316L stainless steel, which has an excellent corrosion resistance and high strength. The Center for Materials Technology, BPPT, in cooperation with a local industry, is currently undertaking research into integrating, refining and alloying processes for the production of medical grade 316L stainless steel, using raw material originating from the ferronickel of Pomalaa. Natural resources of ferronickel, one of the main raw materials for stainless steel, are locally available in Indonesia. Other alloy metals such as steel scrap, ferro chrome and ferro molybdenum are bought in the market. The charging calculation is done by computer-aided simulation, before the melting processes are carried out. The melting facility used is an induction furnace of 250 kg capacity, following the procedures commonly used in the industry. Chemical composition analysis is done by a spectrophotometer. Tensile and hardness tests are conducted, and a microstructure observation is also carried out using an optical microscope and a scanning electron microscope. The selection of raw material inputs and refining and annealing processes affect the quality of the alloy. In our study, we found various forms of oxide inclusions in the stainless steel microstructure: triangular, hexagonal and spherical. The tensile strength of the specimen of 316L stainless steel casting materials was influenced by the presence of oxide phases."
Depok: Faculty of Engineering, Universitas Indonesia, 2015
UI-IJTECH 6:7 (2015)
Artikel Jurnal  Universitas Indonesia Library
cover
An, Sang Woo
"Studi ini membahas pengaruh penambahan mangan & nitrogen dan pengerjaan dingin pada perilaku elektrokimia baja tahan karat austenitik. Mekanisme dari berbagai makalah dievaluasi dengan uji gravimetri dan pengukuran polarisasi. Morfologi produk reaksi yang dikembangkan dalam bahan dianalisis dengan spektroskopi fotoelektron sinar-X (XPS), spektroskopi dispersif energi (EDX), dan mikroskop elektron pemindaian (SEM). Berbagai baja tahan karat austenitik dengan jumlah elemen paduan yang berbeda dievaluasi pada suhu dan lingkungan larutan yang berbeda. Penambahan mangan tidak menunjukkan pengaruh yang luar biasa pada ketahanan korosi secara umum karena kemampuannya yang tidak signifikan untuk membentuk senyawa yang tidak larut. Sementara itu, mangan menunjukkan pengaruh berlawanan terhadap ketahanan korosi lokal, biasanya karena adanya inklusi MnS yang berperan sebagai inisiator pitting. Penambahan N menurunkan celah energi bebas bahan kimia antara struktur BCC dan FCC dan meningkatkan energi kesalahan susun secara lebih signifikan. Akibatnya, N dapat membuat austenit lebih stabil secara termal tetapi memiliki efek yang lebih kecil pada stabilitas mekanik. Ditemukan bahwa nitrogen meningkatkan ketahanan korosi baja. Pengaruh berbagai intensitas deformasi plastis dilakukan dengan pengerolan dingin pada temperatur yang berbeda. Hasil penelitian menunjukkan bahwa pembentukan strain-induced martensite (SIM) jelas memberikan pengaruh yang signifikan terhadap korosi dan sifat mekanik.

The study addresses the effect of manganese & nitrogen addition and cold working on electrochemical behaviors of austenitic stainless steels.  The mechanism from various papers was evaluated by gravimetric tests and polarization measurements. The morphology of the reaction products developed in the material was analyzed by X-ray photoelectron spectroscopy (XPS), energy dispersive spectroscopy (EDX), and scanning electron microscopy (SEM). Various austenitic stainless steels with different amounts of alloying elements were evaluated in different temperatures and solution environments. The addition of manganese did not show a remarkable influence on the general corrosion resistance because of the insignificant ability to form insoluble compounds. Meanwhile, manganese indicated an opposite influence on localized corrosion resistance, normally due to the existence of MnS inclusion which played as pitting initiators. The addition of N decreases the chemical-free energy gap between BCC and FCC structures and raises the stacking fault energy more significantly. Consequently, N can render austenite more thermally stable but has less effect on mechanical stability. It was found that nitrogen improved the corrosion resistance of the steel. The influence of various intensities of plastic deformation is conducted by cold rolling at different temperatures. The result shows that the formation of strain-induced martensite (SIM) obviously led to a significant effect on corrosion and mechanical properties."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Dhedhe Rodat Budi P.
"Baja tahan karat stainless steel 304 merupakan baja yang memiliki ketahanan korosi yang baik dan tahan temperature tinggi sehingga banyak digunakan dalam dunia industri. Penggunaan baja tahan karat umumnya membutuhkan proses penyambungan dimana proses penyambungan yang sangat umum digunakan adalah proses pengelasan. Untuk mendapatkan hasil pengelasan yang baik, diperlukan pemilihan parameter yang tepat agar tidak timbul permasalahan seperti distorsi pengelasan. Distorsi merupakan fenomena perubahan bentuk yang terjadi akibat pengelasan.
Pada penelitian ini dilakukan percobaan untuk mengetahui pengaruh kuat arus dan kecepatan pengelasan terhadap hasil manik las dan juga distorsi yang dihasilkan menggunakan GMAW. Kuat arus yang digunakan yaitu 115, 120, dan 125 A sedangkan kecepatan pengelasan yang digunakan 3,6; 3,9; dan 4,2 mm/s.
Hasil las dilakukan pengukuran terhadap lebar maniknya, kemudian dilakukan pengukuran distorsi menggunakan CMM Coordinate Measuring Machine setelah material mengalami pendinginan alami. Dari hasil penelitian yang didapatkan, diketahui bahwa semakin besar kuat arus, maka lebar manik las dan distorsi angular yang dihasilkan akan semakin besar. Sedangkan jika kecepatan pengelasan semakin besar, maka lebar manik las dan distorsi angular yang dihasilkan akan semakin kecil.

Stainless steel has good corrosion resistance and high temperature resistance, especially for 304 Stainless steel and widely used in many industries. The use of stainless steels generally requires a jointing process, and the most common jointing process used in stainless steel is the welding process. To get a good welding results, the selection of appropriate parameters is needed to avoid problems such as welding distortion. Distortion is a phenomenon of form changes that occur due to welding.
This experiment is conducted to find out the effect of welding current and welding speed toward weld bead and also distortion produced using GMAW. The welding current used is 115, 120, and 125 A while the welding speed used is 3.6 3.9 And 4.2 mm s. The weld bead then measured, and also the distortion is measured using CMM Coordinate Measuring Machine after the material is naturally cooled.
From the results obtained, it is known that the rise of welding current, the width of the weld bead and the resulting angular distortion will be increased. Whereas if the welding speed is increased, the width of the weld bead and the angular distortion will be smaller.
"
Depok: Fakultas Teknik Universitas Indonesia, 2017
S67000
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>