Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 111682 dokumen yang sesuai dengan query
cover
Stevany Lydia Jedidjah Hugen
"Praktik fondasi di Indonesia masih berada pada tahap linear elastis dengan batas displacement yang disyaratkan hanya sebesar 25 mm oleh SNI 8460:2017. Hal ini mengakibatkan desain fondasi di Indonesia tidak efisien dan dianggap boros karena berukuran besar dan berjumlah banyak agar fondasi dapat tetap berperilaku elastis. Jumlah tulangan spiral pada praktik spun pile di Indonesia masih berada di bawah persyaratan minimum ASCE 7-16. Dibutuhkan banyak confinement dengan jarak yang rapat untuk mengatasi masalah tersebut. Namun, hal tersebut dinilai kurang ekonomis. Oleh karena itu, dilakukan studi eksperimen dan studi numerik untuk mengetahui perilaku sambungan spun pile-pile cap dengan perkuatan steel jacketing dengan pembebanan siklik untuk mengatasi permasalahan confinement tersebut. Sambungan spun pile-pile cap yang dimaksud adalah bagian atas permukaan pile cap hingga sekitar 700mm ke bagian spun pile dilihat dari pengujian eksperimen yang dilakukan sebelumnya. Pengujian dan pemodelan numerik dilakukan pada dua spun pile berdiameter 450 mm yang diselubungi beton grouting dan steel jacket. Studi numerik atau finite element secara 3D dilakukan dengan software ABAQUS karena terjadi kegagalan membuat benda uji yang perfectly bonded antara steel jacket dengan beton grouting dan beton grouting dengan spun pile. Studi parametrik juga dilakukan untuk mengetahui kebutuhan tebal dan tinggi steel jacket yang efektif dengan membandingkan terhadap spun pile dengan kebutuhan confinement yang memenuhi persyaratan ASCE 7-16. Hasil pengujian eksperimen dan pemodelan ini berupa kurva histeretik yang akan dianalisis untuk mendapatkan daktilitas, ketahanan lateral, kapasitas penampang, dan anlaisa tegangan. Pemberian steel jacketing meningkatan kekakuan, kekuatan, daktilitas dan menurunkan tegangan sengkang spun pile.

The practice of foundations in Indonesia is still at the elastic stage with the displacement limit is only 25 mm required by SNI 8460:2017. Thus, design of foundation in Indonesia become inefficient and considered wasteful because of large sizes and in large quantities to keep the foundation remain elastic. The amount of confinement in the practice of spun piles in Indonesia is still below the minimum requirements of ASCE 7-16. It takes a lot of confinement with tight distance to overcome this problem. However, it is considered less economical. Therefore, an experimental study was conducted to determine the behavior of the spun pile-pile cap connection with steel jacketing reinforcement to overcome the less amount of confinement. The finite element study is using ABAQUS software because of the interaction failure that occurred between steel jacket and grouting concrete. The parametric study is also carried out to find out the needs of effective thickness and height of the steel jacket to be compared with confinement ideal according to ASCE 7-16. The results of this research and modelling are hysteretic curve that provides several research parameters, which are ductility, lateral load, moment capacity, and stress development. The use of additional steel jacketing results in increasing stiffness, strength, moment capacity and reduce the stress of confinement of spun pile."
Depok: Fakultas Teknik Universitas Indonesia, 2023
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Jansen Reagen
"Studi perkuatan sambungan spun pile terhadap pile cap menggunakan zincalume diusulkan sebagai persyaratan untuk memenuhi rasio confinement spun pile buatan Indonesia. Selain itu, perkuatan bertujuan untuk meningkatkan kekuatan, daktilitas, dan serapan energi gempa oleh spun pile. Oleh karena itu, dilakukan studi eksperimen pada spun pile dengan beton pengisi dan perkuatan steel jacket akibat pembebanan siklik dan dibandingkan dengan benda uji tanpa perkuatan. Dilakukan juga pushover analysis secara monotonik untuk mengamati proses terjadinya sendi plastis dan strain pada material. Terdapat dua benda uji eksperimen berupa spun pile berdiameter 450 mm dengan perkuatan steel jacket yang diberikan beton pengisi bertulang dan salah satu benda uji tanpa beton pengisi bertulang, serta satu benda uji referensi berupa spun pile tanpa perkuatan steel jacket. Hasil eksperimen menunjukan perkuatan steel jacket terbukti dapat meningkatkan kekuatan dan daktilitas benda uji, tetapi masih belum dapat meningkatkan serapan energi gempa. Pengaruh tulangan pada beton pengisi terbukti dapat meningkatkan kekuatan dan daktlitas pada spun pile dengan adanya perkuatan steel jacketing. Parameter penelitian yang diguanakan untuk membandingkan benda uji adalah daktilitas, energi disipasi dan input, degradasi kekuatan dan kekakuan, momen – rotasi, dan kurva histeretik akibat pembebanan siklik.

The study of strengthed spun pile to pile cap connection using zincalume is proposed as a requirement to meet the confinement ratio of spun pile made in Indonesia. In addition, the reinforcement added aims to increase the strength, ductility, and earthquake energy absorbtion by spun pile. Therefore, an experimental study was conducted on the spun pile with reinforced concrete and steel jacket reinforcement due to cyclic loading and compared with the specimen without steel jacket reinforcement. A monotonic pushover analysis was also carried out to observe the process of plastic hinge and strain on the material. There are two experimental specimens in the form of a spun pile with a diameter of 450 mm with steel jacket reinforcement provided with reinforced concrete and one other specimen without reinforced concrete, and one reference test object in the form of a spun pile without steel jacket reinforcement. The experimental results show that steel jacket reinforcement is proven to increase the strength and ductility of the test object, but still cannot increase the absorption of earthquake energy. The effect of reinforcement on infill concrete is proven to increase the strength and ductility of the spun pile with the presence of steel jacketing reinforcement. The research parameters used to compare the specimens were ductility, energy dissipation and input, strength and stiffness degradation, moment-rotation, and hysteretic curve due to cyclic loading."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Jansen Reagen
"Studi numerikal dan parametrik dilakukan menggunakan ABAQUS pada sambungan spun pile - pile cap dengan beton pengisi bertulang serta perkuatan steel jacketing untuk menganalisis efektivitas confinement oleh steel jacketing. Studi eksperimen yang sebelumnya sudah dilakukan menunjukan steel jacketing masih belum mampu menghindari fenomena pinching dan tidak meningkatkan daktiltias secara signifikan. Efek confinement oleh steel jacketing akan ditinjau berdasarkan penurunan tegangan pada sengkang spun pile dan kenaikan kuat tekan beton inti spun pile. Studi parametrik dengan parameter koefisien friksi, tebal dan tinggi steel jacketing, serta beban aksial dilakukan untuk mendapatkan desain efektif dari perkuatan steel jacketing. Hasil pemodelan menunjukan bahwa penggunaan steel jacketing mampu memberikan efek confinement yang baik melalui penurunan stress development yang terjadi pada sengkang spun pile dan peningkatan beton inti spun pile. Desain efektif perkuatan steel jacketing yang disarankan adalah menggunakan zincalume tebal 1 mm dan tinggi 1,5D < H < 2D dimana D adalah diameter spun pile, untuk menghindari terjadinya local buckling pada zincalume.

Numerical and parametric study was conducted using ABAQUS on a spun pile – pile cap connection filled with concrete reinforcement and steel jacket retrofitting to analyse the effectiveness of confinement by steel jacketing. Experimental study that has been conducted before shown that steel jacketing retrofitting wasn’t able to avoid pinching and didn’t significantly increase ductility. Confinement effect by steel jacket will be viewed based on the degradation of stress developed on spun pile’s stirrups and the enhancement of spun pile’s core concrete strength. Parametric study consisting of friction coefficient, thickness and height of steel jacketing, and axial load was conducted to achieve an effective design of steel jacket retrofitting. Modelling results shown that the use of steel jacket retrofitting was able to provide good confinement by reducing the stress development that occur on the spun pile’s stirrups as well as enhancement in spun pile’s core concrete strength. An effective design of steel jacketing retrofitting that was suggested is using a 1 mm in thickness zincalume and height of 1,5D < H < 2D, where D is the diameter of spun pile, to avoid local buckling on the zincalume."
Depok: Fakultas Teknik Universitas Indonesia, 2023
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Fathia Handayani Kamal
"Spun pile pada jenis fondasi elevated RC pile cap (EPC) merupakan tiang pancang beton bertulang yang berbentuk lingkaran lubang di bagian tengah yang difabrikasi secara pracetak dan prategang yang dijadikan satu kesatuang pada fondasi yang ditanam sebagian dalam tanah dengan letak pile cap yang ditinggikan dari permukaan tanah. Pada penelitian ini, diinvestigasi perilaku keruntuhan model fondasi spun pile yang berdasar dari penggabungan fondasi EPC dari eksperimen Liu et al. (2020) untuk fondasi tiang grup 1x1, 2x2, dan 2x3 pada tanah pasir dan eksperimen spun pile SPPC untuk tiang hollow dan infill. Permodelan numerikal dilakukan berdasarkan pendekatan Beam-on-Nonlinear-Wrinkler-Foundation (BNWF) melalui aplikasi Opensees, dengan tanah pasir dari eksperimen Liu et al disubstitusi menjadi tanah lempung. Diberikan variasi kuat geser tanah sebesar 20, 60, dan 100 KPa untuk mengetahui bagaimana nilai daktilitas, proses pembentukan sendi plastis, dan interaksi tanah lempung dengan masing-masing jenis tiang fondsi grup. Daktilitas yang didapat dari permodelan fondasi 1x1, 2x2, dan 2x3 untuk tiang infill secara berturut-turut adalah 3.942, 3.738, dan 3.55. Semakin besar nilai kuat geser yang digunakan maka semakin besar gaya dalam momen yang dihasilkan dan semakin cepat pula pembentukan sendi plastis, maka semakin besar kuat geser semakin tinggi lokasi sendi plastis. Untuk semua jenis model fondasi, akan terbentuk sendi plastis yang terletak pada pile head atau sambungan. Yang terbentuk sendi plastis kedua di dalam tanah hanya pada tiang SPPC02 fondasi tunggal dengan kuat geser tanah 60 KPa dan 100 KPa. Pembentukan sendi plastis pada model terbentuk di semua tiang. Untuk fondasi 2x3, walaupun momen pada leading pile dan center pile berbeda, dimana momen pada center pile lebih kecil, tetap terbentuk sendi plastis. Semakin tinggi kuat geser tanah yang digunakan, maka semakin rendah defleksi yang terjadi. Faktor P-multiplier juga mempengaruhi besar defleksi yang dihasilkan, pada nilai kuat geser tanah yang sama, semakin besar faktor p-multiplier yang diberikan pada tiang, maka akan semakin kecil nilai defleksi yang dihasilkan tiang tersebut. Pada tegangan tanah, semakin tinggi nilai kuat geser tanah maka semakin cepat perubahan elastis menjadi plastisitas pada tanah. Jenis tiang, atau lebih spesfiknya nilai p-multiplier, mempengaruhi tegangan tanah, yang mana semakin kecil nilai p-multiplier nya maka semakin kecil tegangan batasnya, namun sejalan juga dengan semakin kecil tegangan tanah yang dihasilkan tiap tiang pada model.

Elevated RC pile cap (EPC) is a reinforced concrete pile partially buried in the ground with its pile cap high from the ground. The inelastic behavior of spun pile hollow and infill piles on 1x1, 2x2, and 2x3 EPC pile foundations is investigated. Numerical modeling is carried out based on the Beam-on-Nonlinear-Wrinkler- Foundation (BNWF) approach through Opensees. The shear strength variations (Su) of 20, 60, and 100 KPa were given to determine the ductility value, how the plastic hinges formed, and the interaction of clay with each group foundation pile. The ductility obtained from modeling the 1x1, 2x2, and 2x3 foundations for the infill piles are 3,942, 3,738, and 3.55, respectively. The greater the value of Su used, the greater the resulting moment, and the faster the formation of plastic hinges. Plastic hinges are formed at connections in all types of foundations. The higher the Su value used, the lower the deflection occurs. The greater the p-multiplier factor given to the pile, the smaller the deflection produced. The higher the Su value, the faster the soil changes to plasticity. The smaller the p-multiplier value, the smaller the limit soil stress, but in line with the smaller the soil stress produced by each pile in the model."
Depok: Fakultas Teknik Universitas Indonesia, 2022
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Stevany Lydia Jedidjah Hugen
"Praktik fondasi di Indonesia masih berada pada tahap linear elastis dengan batas displacement yang disyaratkan hanya sebesar 25 mm oleh SNI 8460:2017. Hal ini mengakibatkan desain fondasi di Indonesia tidak efisien dan dianggap boros karena berukuran besar dan berjumlah banyak agar fondasi dapat tetap berperilaku elastis. Jumlah tulangan spiral pada praktik spun pile di Indonesia masih berada di bawah persyaratan minimum ACI 318-19. Dibutuhkan banyak confinement dengan jarak yang rapat untuk mengatasi masalah tersebut. Namun, hal tersebut dinilai kurang ekonomis. Oleh karena itu, dilakukan studi eksperimen untuk mengetahui perilaku sambungan spun pile-pile cap dengan perkuatan steel jacketing dengan pembebanan siklik lalu dibandingkan dengan monotonic pushover analysis pada software Opensees. Pengujian dan permodelan dilakukan pada dua spun pile berdiameter 500 mm yang diselubungi steel jacketing yaitu dengan beton pengisi dan tanpa beton pengisi. Hasil pengujian eksperimen dan permodelan ini berupa kurva histeretik yang akan dianalisis untuk mendapatkan daktilitas, energi disipasi, degradasi kekuatan, degradasi kekakuan, overstrength ratio, dan momen rotasi. Pembebanan siklik yang diberikan mengikuti ACI 374.2r. Pemberian steel jacketing meningkatan kekakuan, kekuatan, enregi disipasi dan overstrength ratio, namun menurunkan daktilitas, serta memindahkan area terjadinya sendi plastis. Pemberian beton pengisi meningkatkan overstrength ratio, namun menurunkan daktilitas, kekakuan, kekuatan, dan energi disipasi.

The practice of foundations in Indonesia is still at the elastic stage with the displacement limit is only 25 mm required by SNI 8460:2017. Thus, design of foundation in Indonesia become inefficient and considered wasteful because of large sizes and in large quantities to keep the foundation remain elastic. The amount of confinement in the practice of spun piles in Indonesia is still below the minimum requirements of ACI 318-19. It takes a lot of confinement with tight distance to overcome this problem. However, it is considered less economical. Therefore, an experimental study was conducted to determine the behavior of the spun pile-pile cap connection with steel jacketing reinforcement with cyclic loading and then compared with monotonic pushover analysis on Opensees. The research and modelling were carried out on two objects of 500mm diameter spun pile covered with steel jacketing, namely with concrete infill and without concrete infill to determine the effect of concrete infill on the spun pile-pile cap. The results of this research and modelling are hysteretic curve that provides several research parameters, which are ductility, energy dissipation, strength degradation, stiffness degradation, overstrength ratio, and moment rotation. The cyclic loading applied is following ACI 374.2r. The use of additional steel jacketing results in increasing stiffness, strength, energy dissipation, overstrength ratio, reduction of ductility and moving the area where plastic hinges occur. The use of concrete infill results in increasing overstrength ratio and reduction of ductility, stiffness, strength, and energy dissipation."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nadila Rahmariana
"Spun pile digunakan secara luas dalam konstruksi bangunan pencakar langit serta jembatan di Indonesia. Namun, spun pile yang digunakan di Indonesia ditemukan memiliki daktilitas dan rasio volumetrik kekangan spiral yang rendah. Selain itu, sambungan dari pile-pile cap biasanya adalah bagian dengan kerusakan terbanyak terutama ketika terjadi gempa bumi.
Analisa numerik untuk studi perilaku dari sambungan spun pile pile cap berbasis common practice di Indonesia dilaksanakan menggunakan software SAP2000. Spesimen spun pile diperoleh dari PT. Wika, permodelan numerical diproses untuk pushover analysis menggunakan beban monotonik untuk melihat perilakunya. Berbagai parameter seperti efek dari jarak kekangan spiral, efek dari diameter spiral, efek dari rasio area tulangan baja, dan efek dari tambahan isian beton dipelajari.

Spun pile is extensively used for high rise buildings and bridges construction in Indonesia. However, it is found that the spun pile used in Indonesia has lower ductility and volumetric ratio of spiral confinement. In addition, connection of the pile pile cap is usually the part with most damage especially when earthquake event is occurred.
Numerical analysis to study the behavior of spun pile-pile cap connection based on common practice in Indonesia is conducted using SAP2000 software. The spun pile specimens used in the analysis model are obtained from PT. Wika, the models are subjected to pushover analysis using monotonic load in order to observe the behavior. Various parameters such as the effect of confinement spacing, effect of spiral wire diameter, effect of steel reinforcement area ratio, and effect of core fill addition are studied."
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Desriana Permatasari
"Sambungan spun pile-pile cap adalah struktur penting yang menyambungkan dan menyalurkan beban dari struktur atas ke struktur bawah hingga ke dalam tanah. Performance Based Design (PBD) belum diizinkan diterapkan di Indonesia sebagai acuan desain. Menurut SNI 8460:2017, penegakkan batas desain fondasi masih mengacu berdasarkan konsep elastik tiang yang menyebabkan ketidakekonomisan pemasangan tiang akibat overdesign dari ukuran dimensi tiang. Damage (kerusakan) adalah bentuk kegagalan atau ketidakmampuan struktur dari tegangan dari yang terlampaui. Pemodelan ABAQUS digunakan untuk melihat output dari berbagai variasi sehingga didapatkan korelasi variabel-variabel yang memengaruhi kerusakan, yaitu volumetrik rasio dan sebaran dari tulangan spiral, tulangan longitudinal, dan besarnya beban aksial. Variasi tulangan spiral dan longitudinal memberi pengaruh persebaran kerusakan yang lebih merata menjadi kerusakan-kerusakan kecil dan mengurangi sebaran localized damage. Sedangkan variasi beban aksial memengaruhi persebaran kerusakan menjadi lebih tinggi akibat membutuhkan gaya yang lebih besar untuk mencapai drift tertentu.

The continuation of spun pile-pile cap is an important structure that connects and transfers loads from the upper structure to the lower structure and into the ground. Performance Based Design (PBD) is not yet permitted to be implemented in Indonesia as a design reference. According to SNI 8460:2017, the enforcement of foundation design limits still relies on the concept of elastic piles, which leads to uneconomical pile installation due to overdesign in pile dimensions. Damage refers to the form of failure or the inability of a structure to withstand excessive stress. ABAQUS modeling is used to observe the output of various variations to obtain correlations of variables that affect damage, such as volumetric ratio and distribution of spiral reinforcement, longitudinal reinforcement, and axial load magnitude. Variations in spiral and longitudinal reinforcement contribute to a more uniform distribution of small damages and reduce the spread of localized damage. On the other hand, variations in axial load affect the spread of damage, as they require greater force to achieve a certain drift.
"
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Yehezkiel
"Dalam studi yang dilakukan oleh Alfetra Henoch Tandita di Universitas Indonesia pada tahun 2021 mengenai sambungan spun pile-pile cap dengan benda uji berupa spun pile dengan beton pengisi, diperoleh hasil berupa parameter-parameter sambungan, seperti daktilitas, momen rotasi, dan lain-lain. Pada studi lanjutan ini, akan ditinjau mengenai damage atau kerusakan secara khusus dan lebih mendalam, terutama mengenai parameter yang menyebabkan persebarannya pada sambungan spun pile-pile cap. Parameter-parameter yang diujikan untuk mengetahui hubungannya dengan damage yang muncul antara lain parameter tulangan spiral, tulangan longitudinal, dan beban aksial. Dalam pengujian numerik menggunakan software ABAQUS ini, diperoleh hasil bahwa parameter aksial merupakan parameter yang paling konsisten dan signifikan dalam menambah kekakuan spun pile, sehingga damage yang ada lebih tersebar dan tidak terlokalisasi. Parameter berikutnya yang cukup konsisten adalah tulangan spiral, dan yang terakhir adalah parameter tulangan longitudinal. Parameter tulangan longitudinal dinilai tidak konsisten karena perkembangannya tidak mengikuti suatu pola tertentu, yang diduga diakibatkan kapasitas tulangan-tulangan longitudinal parameternya yang telah mendekati titik fracture.

In a study conducted by Alfetra Henoch Tandita at the University of Indonesia in 2021, regarding the connection between spun pile-pile cap and a test object consisting of a spun pile with filled concrete, results were obtained in the form of connection parameters such as ductility, rotational moment, and others. In this further study, the focus will be on examining the specific and deeper aspects of damage, particularly regarding the parameters that cause its distribution in the spun pile-pile cap connection. The parameters tested to understand their relationship with the emerging damage include spiral reinforcement, longitudinal reinforcement, and axial load. Through numerical testing using the ABAQUS software, it was found that the axial parameter is the most consistent and significant parameter in increasing the stiffness of the spun pile, resulting in more widespread and non-localized damage. The next parameter that showed sufficient consistency is the spiral reinforcement, and the last one is the longitudinal reinforcement parameter. The longitudinal reinforcement parameter is considered inconsistent because its development does not follow a specific pattern, which is suspected to be caused by the longitudinal reinforcement's capacity approaching the point of fracture.
"
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Fadel Muhammad
"Studi numerik yang dihasilkan oleh perangkat lunak SAP2000 untuk mengamati perilaku sambungan spun pile ke pile cap sesuai dengan praktik umum standar Indonesia dengan penguatan selubung baja tambahan. Analisis push over dilakukan dalam penelitian dengan pendekatan pemuatan monotonik. Parameter dalam pengujian adalah ketebalan jaket baja dan adanya perekat antara baja dan permukaan beton. Jaket baja yang dibangun mengikuti metode baru menunjukkan hasil yang baik untuk meningkatkan kekuatan tekan dan daktilitas tiang berselimut baja sehubungan dengan tiang pancang. Selubung baja yang lebih tebal menunjukkan peningkatan kekuatan tekan, dan perekat antara baja dan permukaan beton mengurangi efek pengekangan dari selubung baja.

Numerical study was generated by SAP2000 software to observe the behaviour of spun pile to pile cap connection according to the common practice of Indonesia standard with additional steel jacketing strengthening. Push over analysis were conducted in the research with monotonic loading approach. The parameters in the test were the steel jacket's thickness and the existence of adhesive between steel and concrete surface. The steel jacket built following the new method showed good results of increasing the compressive strength and ductility of the jacketed pile with respect to the plain pile. The thicker steel jackets showed that the increased compressive strength, and the adhesive between steel and concrete surface reduced the confining effect of the steel jackets."
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Badaruddin
"Proyek pembangunan world trade center 3 (WTC 3) menggunakan pondasi pile raft lengkap dengan 5 lantai basement dan retaining structure yang mengelilinginya berupa secant pile dia. 800 mm untuk menopang 44 lantai bangunan tower serta 4 lantai podium, desain pondasi pile raft tersebut belum meperhitungkan keberadaan retaining structure serta kekakuan dari konstruksi basement. Sejatinya pondasi pile raft, retaining structure & element struktur basement terintegrasi dan bekerja secara bersama-sama dalam meneruskan beban struktur atas ke masa tanah dibawah pondasi.
Pada penelitian ini telah dilakukan pengujian melalui analisa numerik dengan menggunakan software GTS Midas terhadap sejumlah model dan ditemukan bahwa keberadaan retaining structure dan elemen struktur basement dapat mengurangi settlement (maksimum settlement serta differential settlement) dan internal force (bending moment & shear force) yang terjadi pada pondasi pile raft melalui mekanisme pengekangan ujung raft dan masa tanah dibawah raft serta transfer beban vertikal dari raft ke retaining structure sehingga sebagin beban vertikal dipikul oleh retaining structure. Efek pengekangan dan mekanisme transfer beban retaining structure dapat bekerja efektif pada rasio Dw/Dt < 1.3 serta pada sistem pondasi partially pile raft.

The construction of world trade center 3 (WTC 3) project are using pile raft as a foudation to support 44 floors of tower building and 4 floors of podium building. This foundation is integrated with five floors of basement and retaining structure. The type of retaining structure used is secant pile with 800 mm diameter in which the position of retaining structure lies on the circumferences of the basement. The original design of the pile raft foundation are not consider the existence of retaining structure and the structural element stiffness of basement likes column, beam etc. In fact that pile raft, basement element structure and retaining structure are integrated and working together in transfer load from upper structucture to soil.
In this reasearch it was examine a number of model with numerical analysis using GTS midas software and it was known that the interaction of retaining structure and basement element structure can reduce settlement (Maximum settlement and differential settlement) and internal force (bending moment & shear force) on pile raft foundation by two mechanism. The first mechanism is the retaining structure and basement element structure can restraining the end of raft and the second mechanis is vertical load transfer from raft to retaining structure. Both of the mechanisms are effective for rasio Dw/Dt less than 1.3 and for partially pile raft.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
T43759
UI - Tesis Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>