Hasil Pencarian  ::  Simpan CSV :: Kembali

"Oleic acid, one of the major components of palm oil, has attracted much interest in modern oleochemistry. The internal olefin group in oleic acid is a useful functional group in the transformation of a fatty acid to other functional chemicals and materials. In this paper, we discuss the application of the olefin metathesis reaction by preparing a long-chain dicarboxylic acid and alkene from the ester of oleic acid. The internal olefin metathesis reaction of methyl oleate produced dimethyl 9-oktadecendioate and 9-octadecene in the presence of a ruthenium Grubbs II (second generation) catalyst with a 51% yield. We also found that there was a higher amount of the E isomer products than the Z isomer products."

"Indonesia, as the largest palm oil producer in the world, also produces palm oil mill effluent (POME). While the latter is a liquid waste that is hazardous for the environment, with proper processing, it can be a potential energy source. The objective of this study was to study the performance of biogas production from POME at various temperatures. The POME and sludge mixture was fermented, according to the treatment, at 27-28oC, 45oC, and 55oC, with the results showing that methane could thereby be produced by as much as 0,19 m3, 0,25 m3, and 0,28 m3 respectively. For each kilogram of chemical oxygen demand (COD) removal, with POME fermentation at room temperature, 45oC, and 55oC, biogas could be produced with methane content of 65.44%, 62.57%, and 59.15%, respectively."

"In the palm oil refining processes, the free fatty acid content is reduced to an acceptable level by using steam-stripping that causes, also, the loss of nutraceuticals such as tocopherols and carotenoids. An alternative method, such as solvent extraction, to separate free fatty acids, especially palmitic acid as the major free fatty acid present in palm oil, will conserves not only the important nutraceuticals but, also, conserves energy because a steam requirement is eliminated. The objective of this research is to evaluate the performance of Natural Deep Eutectic Solvents (NADES), each consisting of betaine as the hydrogen bonding acceptor and a polyalcohol as the hydrogen bonding donor, to extract palmitic acid from palm oil. The goal is to obtain a NADES that is able to extract palmitic acid from palm oil with the highest extraction yield. The viscosity of various studied NADES was 10-236 cSt while the polarity parameter, determined by using Nile red as the solvatochromic dye, was 48.9-50.8 kcal/mol. The obtained data shows that, for NADES having similar polarity to that of betaine, the extraction yields reduce with increasing viscosity of the NADES. The highest extraction yield of 60% (w/w), corresponding to a distribution coefficient value of 0.75, was obtained by using NADES consisting of betaine and 1,2-butanediol. The extraction yield and distribution coefficient values indicated the potential of NADES, prepared by friendly compounds of betaine and polyalcohols, as alternative green solvents in the solvent extraction process when separating free fatty acids from palm oil."

"ng have been one of the key processes that drive these advancements. A lot of these processes are driven through the help of lubricants for easier machine processes. Lubricants are used due to its ability to significantly reduce coefficient of friction (COF) and wear scar dimension (WSD) which directly affect the efficiency of the equipment and prolong their lifetime. Incorporation of additives can be carried out to improve the lubrication efficiency by incorporating nanoparticles to a Polyalphaolefin (PAO) base oil. In this research, Tin (IV) Oxide is used as the nanoparticle additive at 1 wt%, 3 wt%, 5 wt%, and 7 wt% tin oxide synthesized from nitric acid leaching of dry tin-lead solder dross from electronic solder application and and addition of 1:1 ratio of oleic acid surfactant. The results suggest that the incorporation of tin oxide greatly decreases the COF and WSD, as well as increasing the average film formation percentage and stability, where the results are directly proportional with the increase in tin oxide concentrations.

---

Pada abad ke-21, perkembangan industri dan teknologi sudah semakin meningkat. Teknologi industri seperti yang digunakan didalam proses manufaktur menjadi salah satu kunci kesuksesan yang mendorong perkembangan tersebut. Banyak dari proses manufaktur tersebut terbantu oleh penggunaan lubrikan untuk memudahkan kinerja mesin industri. Lubrikan digunakan dalam industri karena sifatnya yang dapat menurunkan coefficient of friction (COF) dan wear scar dimension (WSD) secara signifikan, yang secara langsung berdampak kepada peningkatan efisiensi peralatan serta meningkatkan umur pemakaiannya. Aditif nanopartikel dapat ditambahkan ke dalam lubrikan Polyalphaolefin (PAO) untuk meningkatkan efisiensi lubrikasi. Dalam riset ini, Timah (IV) Oksida digunakan sebagai aditif nanopartikel dengan penambahan 1 wt%, 3 wt%, 5 wt%, dan 7 wt% yang telah disintesis dengan proses leaching menggunakan asam nitrat yang berasal dari limbah solder timah-timbal dari solder elektronik ditambah dengan surfaktan asam oleat dengan perbandingan 1:1. Hasil proses tersebut menunjukkan bahwa penambahan timah oksida menurunkan COF dan WSD secara signifikan serta meningkatkan persentase pembentukan dan stabilitas lapisan lubrikasi, dimana hasil tersebut menunjukkan hasil yang proporsional dengan peningkatan penambahan konsentrasi timah oksida."

"Dengan perkembangan industri yang cukup cepat diperlukan perlindungan untuk alat-alat proses yang merupakan suatu komponen penting dalam proses produksi. Perlindungan ini dapat berupa inhibitor korosi yang menjaga peralatan dari korosi terutama industry minyak dan gas bumi yang bersentungan langusng dengan fluida yang memiliki kecepatan dan tekanan tinggi, serta keadaan fluida yang asam sehingga dapat menyebabkan korosi pada peralatan produksi seperti sistem perpipaan. Proposal ini akan membahas mengenai produksi dari turunan imidazolin yang terbentuk dari asam oleat dan trietiltertamina yang dapat digunakan sebagai inhibitor korosi dengan melakukan simulasi proses serta pada proposal ini akan dilakukan perhitungan keekonomian untuk mengetahui seberapa mungkin perusahaan ini untuk dibangun di Indonesia.

---

With the rapid development of the industry, protection is needed for process equipment, which is an important component in the production process. This protection can take the form of corrosion inhibitors that protect equipment from corrosion, especially in the oil and gas industry, where they come into direct contact with fluids that have high velocity and pressure, as well as acidic conditions that can cause corrosion in production equipment such as pipeline systems. This proposal will discuss the production of turunan imidazoline, which is formed from oleic acid and triethylamine and can be used as a corrosion inhibitor. It will simulate the process and also include an economic calculation to determine the feasibility of establishing this company in Indonesia."

"Penggunaan distilasi reaktif pada produksi biodiesel melalui proses esterifikasi asam oleat dengan alkohol mampu mengatasi kendala reaksi keseimbangan terbatas yang terjadi pada unit yang terpisah antara reaktor dan kolom distilasi. Proses ini memerlukan struktur pengendalian (control strukture, CS) yang tepat agar tujuan optimalisasi produksi tersebut dapat tercapai. Struktur tersebut menggunakan pengendali proportional-integral (PI) dengan metode penyetelan auto tuning. Disain sistem pengendalian proses pada distilasi reaktif ini meliputi empat pengendali laju alir (laju alir asam oleat, metanol, distilat dan bottom), dua pengendali level (level condenser dan reboiler), satu pengendali tekanan (tekanan top-stage) dan satu pengendali suhu (suhu talam-12). Sebagai ukuran kinerjanya adalah integral kesalahan yang dipangkatkan (integral of square error, ISE). Hasilnya, CS-1 (pengendali suhu talam-12 menggunakan laju alir reboiler sebagai manipulated variable, MV) menunjukkan kinerja lebih baik dibandingkan CS-2 (laju alir masuk methanol sebagai MV). Pada uji perubahan titik-set, CS-1 memiliki rata-rata ISE CS-1 lebih kecil (2069.4) dibanding CS-2 yang mempunyai ISE sebesar 2742.9. Sedangkan pada uji gangguan laju alir umpan, CS-1 kembali mempunyai rata-rata ISE yang jauh lebih kecil (0.36) dibanding CS-2 sebesar 33.44. Pada anilisis keekonomian pun CS-1 berhasil mengungguli CS-2, CS-1 mempunyai rasio manfaat dan biaya 1.6 (>1) sedangkan CS-2 mempunyai rasio manfaat dan biaya 0.5 (<1). Hal ini terjadi karena pada CS-1 kemurnian produk dapat dijaga di atas spesifikasi fuel grade

---

The use of reactive distillation in the production of biodiesel by esterification of oleic acid with alcohol is able to overcome obstacles equilibrium limited reaction which occurs in a separate unit between the reactor and distillation column. This process requires the control structures (Control Structure, CS) is appropriate for the purpose of production optimization can be achieved. The structure using the controller proportional-integral (PI) with auto tuning adjustment method. The design of process control systems in reactive distillation includes four controllers flow rate (the flow rate of oleic acid, methanol, distillate and bottom), two control levels (level condenser and reboiler), the control pressure (pressure top-stage) and a suhue controller (suhue stage-12). As a measure of its performance is raised to a fault integral (integral of square error, ISE). As a result, CS-1 (a suhue controller tray-12 using a flow rate of reboiler as the manipulated variable, MV) showed better performance than the CS-2 (the inlet flow rate of methanol as MV). In the test set-point change, CS-1 has an average ISE CS-1 is smaller (2069.4) compared to CS-2, which has amounted to 2742.9 ISE. While the test feed flow rate disorders, CS-1 had an average return ISE much smaller (0.36) compared to CS-2 at 33.44. In the economic analysis, no CS-1 outperformed CS-2, CS-1 has a benefit-cost ratios of 1.6 (> 1) while CS-2 has a benefit-cost ratios of 0.5 (<1). This occurs because the CS-1 product purity can be maintained above the specification of fuel grade."

"Asam oleat atau asam Z-Δ9-oktadekanoat diketahui sebagai salah satu asam lemak yang memiliki toksisitas yang rendah dan memiliki aktivitas antimikroba, sehingga dikembangkan penelitian untuk mendapatkan senyawa turunan dari asam oleat dan mengetahui bioaktivitasnya. Pada penelitian ini, dilakukan sintesis turunan asam amino dari senyawa asam oleat dengan reaksi esterifikasi dan amidasi, lalu dikarakterisasi dengan KLT dan FTIR. Asam oleat diesterifikasi dengan katalis basa, kemudian diamidasi dengan asam amino glisin dan asam amino fenilalanin. Setelahnya, dilakukan uji pendahuluan BSLT dan uji antimikroba dengan metode difusi cakram. Dari hasil penelitian didapatkan % kematian dari konjugat asam oleat, glisin oleat, dan fenilalanin oleat. Asam Oleat dengan konsentrasi 16,6 ppm memiliki % kematian paling tinggi yaitu 35%. Adapun hasil uji antimikroba konjugat asam oleat, glisin oleat, dan fenilalanin oleat tidak memiliki aktivitas antimikroba terhadap bakteri kulit gram positif yaitu Staphylococcus aureus dan bakteri kulit gram negatif yaitu Escherichia coli.

---

Oleic acid or Z-Δ9-octadecanoic acid is known as a fatty acid that has low toxicity and antimicrobial activity, so research was developed to obtain compounds derived from oleic acid and determine its bioactivity. In this research, the synthesis of amino acid derivatives from oleic acid compounds by esterification and amidation reactions was carried out, then characterized by TLC and FTIR. Oleic acid is esterified with a base catalyst, then amides with the amino acid glycine and the amino acid phenylalanine. After that, a preliminary BSLT test and an antimicrobial test using the disc diffusion method were carried out. From the results of the study obtained % of deaths from conjugates of oleic acid, glycine oleic, and phenylalanine oleate. Oleic acid with a concentration of 16.6 ppm had the highest % mortality, namely 35%. The results of the antimicrobial conjugate test of oleic acid, glycine oleic, and phenylalanine oleate did not have antimicrobial activity against gram-positive skin bacteria, namely Staphylococcus aureus and gram-negative skin bacteria, Escherichia coli."

"Deep Eutectic Solvent (DES) adalah pelarut ramah lingkungan yang tidak mudah menguap dan dapat digunakan sebagai pelarut ekstraksi untuk menghilangkan asam oleat dari minyak kelapa sawit. Ini disebabkan oleh rendahnya tingkat toksisitas dan tidak memengaruhi kandungan antioksidan dari minyak kelapa sawit. Penelitian ini bertujuan untuk mencapai pemisahan yang efisien dari asam oleat dari minyak kelapa sawit dengan menyaring DES yang melarutkan asam oleat paling tinggi, menentukan kondisi optimal dalam proses pembekuan fraksional, dan menganalisis kandungan minyak kelapa sawit dalam DES menggunakan kromatografi gas serta kandungan DES dalam minyak kelapa sawit menggunakan metode titrasi Karl-Fischer. DES terbaik ditentukan dari hasil penapisan yang memiliki tingkat solubilitas tertinggi, yaitu kolin klorida (HBA) dan 1,2-oktandiol (HBD) dengan rasio molar 1:7 yang memiliki efisiensi ekstraksi sebesar 68,3%. Dalam proses pembekuan fraksional, sampel diuji dengan variasi suhu pendinginan sebesar 5°C, 10°C, dan 14°C. Dari hasil yang didapatkan, DES terbaik memiliki persentase recovery kandungan asam oleat dalam DES setelah pendinginan sebesar 53,33%.

---

Deep Eutectic Solvent (DES) is a non-volatile, environmentally friendly solvent that can be used as an extraction solvent to remove oleic acid from palm oil. This is due to its low toxicity and does not affect the antioxidant content of palm oil. This study aims to achieve efficient separation of oleic acid from RBD palm olein by screening DES that dissolves the highest oleic acid, determining the optimal conditions in the fractional freezing process, and analyzing the palm oil content in DES using gas chromatography as well as the DES content in palm oil using the Karl-Fischer titration method. The best DES was determined from the screening stage that had the highest solubility level, namely choline chloride (HBA) and 1,2-octanediol (HBD) with a molar ratio of 1:7 which had an extraction efficiency of 68.3%. In the fractional freezing method, the samples were tested with cooling temperature variations of 5°C, 10°C, and 14°C. From the results obtained, the best DES has a recovery percentage of oleic acid content in DES after fractional freezing of 53.33%."

"ABSTRAKBiosurfaktan merupakan produk turunan dari ester yang dapat disintesis dari asam lemak dan gula alkohol. Biosurfaktan bersifat biodegradable dengan toksisitas rendah, biocompatible serta memiliki aktivitas spesifik pada kondisi tertentu. Salah satu aplikasi biosurfaktan adalah dapat mencakup bidang petroleum. Produksi biosurfaktan dalam skala lebih luas untuk keperluan petroleum layak diwujudkan. Sebagai langkah awal, perlu dipertimbangkan beberapa strategi agar produksi yang dilakukan bersifat cost-effective. Salah satu jenis biosurfaktan yang berpotensi sebagai bahan bakar fuel adalah ester karbohidrat. Reaksi enzimatik produksi biosurfaktan pada penelitian ini menggunakan substrat berupa sorbitan dan asam oleat yang dikatalisis oleh Novozym 435 untuk menghasilkan ester sorbitan oleat. Selanjutnya, campuran mikroemulsi yang terdiri dari minyak diesel komersiil, air, ester sorbitan oleat, dan ester sorbitan oleat teretoksilasi disintesis. Berdasarkan penelitian ini, diperoleh hasil bahwa kondisi terbaik dari sistem reaksi ini belum dapat ditentukan karena reaksi esterifikasi antara sorbitan dan asam oleat menggunakan Novozym 435 tidak cukup efektif dilakukan dalam sistem campuran pelarut organik. Hal tersebut diindikasikan karena gugus ndash;OH dari pelarut dapat menutupi sisi aktif dari enzimnya sehingga dapat mengganggu proses terbentuknya ester. Apabila reaksi esterifikasi secara enzimatik dilangsungkan dalam sistem bebas pelarut, substrat sorbitan tidak dapat bercampur baik dengan asam oleat, dikarenakan wujud dari sorbitan yang cukup lengket pada suhu 60. Besaran kinematika viskositas dan densitas dari diesel = 2,97 cSt dan 0,83 gr/mL. Serta besaran kinematika viskositas dan densitas dari campuran mikroemulsi diesel/Tween80/Span80/air = 11,69 cSt dan 0,88 gr/mL. Campuran antara surfaktan dari jenis sorbitan oleat Span 80 dan ko-surfaktan dari jenis sorbitan oleat teretoksilasi Tween 80 , dapat membentuk campuran mikroemulsi dari minyak dan air serta dapat berpotensi sebagai bahan bakar mikroemulsi. Hal ini didasarkan pada besaran densitas dan wujud dari campuran yang membentuk 1 fasa serta stabil selama 2 minggu.

---

ABSTRACTBiosurfactant is a derivative product of esters which can be synthesized from fatty acid and sugar alcohol. Biosurfactant is biodegradable with low toxicity, biocompatible, and has a specific activity under certain condition. One kind of biosurfactant application is for petroleum purposes. Production of biosurfactant on a wider scale for petroleum purposes is feasible. As a first step, several strategies are needed to make the production cost is effective. One type of biosurfactant which has a potential as a fuel is carbohydrate ester. In this study, the enzymatic reaction of biosurfactant production was using sorbitan and oleic acid as the substrates which catalyzed with Novozym 435 to produce sorbitan oleic ester. Furthermore, a mixture of microemulsion that comprising commercial diesel oil, water, sorbitan oleate ester, and ethoxylated sorbitan oleate ester was synthesized. Based on this study, it is still not be determined for a best condition of enzymatic reaction because the esterification reaction between sorbitan and oleic acid using Novozym 435 was not quietly effective in an organic solvent blend system. It could happen because the OH solvent group could mask the active site of the enzyme thus disturbing the ester forming process. If an enzymatic esterification was carried out in a solvent free system, the sorbitan could not be well mixed with oleic acid, due to the sticky sorbitan at 60. Magnetic viscosity magnitude and diesel density 2,97 cSt and 0,83 gr mL. As well as the magnitude of kinematic viscosity and density of diesel Tween80 Span80 water as a mixture of microemulsion were 11,69 cSt and 0,88 gr mL, respectively. The mixture between the sorbitan oleate typed surfactant Span 80 and the co surfactant of ethoxylated sorbitan oleate Tween 80 , may form a microemulsion mixture of oil and water and has a potential as a microemulsion fuel. It is based on the value of density and the physical form of the mixture which is 1 phase and stable during 2 weeks."