Hasil Pencarian  ::  Simpan CSV :: Kembali

"Telah dilakukan sintesis katoda LiFePO4/V berlapis karbon dari karbon aktif tempurung kelapa untuk katoda baterai lithium ion. Prekursor yang digunakan adalah LiOH, NH4H2PO4, dan FeSO4.7H2O dibuat melalui proses hidrotermal. Selanjutnya, dilakukan pencampuran karbon dari karbon aktif tempurung kelapa sebanyak 4 dan variasi vanadium serbuk yang bersumber dari H4NO3V. Campuran LiFePO4/V/C dikarakterisasi menggunakan analisis termal STA untuk menentukan temperatur sintering. Hasilnya sintesis terjadi pada temperatur di atas 681,950C dan serbuk berwarna abu-abu gelap sebagai karakteristik dari LiFePO4. Kemudian proses sintering dilakukan pada temperatur 8500C selama 4 jam. Serbuk LiFePO4 sintesis dikarakterisasi menggunakan difraksi sinar-X XRD, mikroskop elektron dan pendeteksi unsur SEM-EDS serta sifat listrik melalui spektroskopi impedansi EIS. Hasil XRD menunjukkan LiFePO4/V/C telah terbentuk dengan struktur berbasis olivin. Hasil SEM-EDS menggambarkan partikel yang teraglomerasi dan LiFePO4/V telah terlapisi karbon. Hasil EIS menunjukkan konduktivitas sebesar 5,33 x 10-5 S/cm untuk LiFePO4/C tanpa vanadium dan 6 x 10-6 S/cm untuk LiFePO4/C dengan doping vanadium 5.

---

Activated carbon from coconut shell has been used as an additive to form LiFePO4 V C composite for lithium ion battery cathode. Lithium iron phosphate LFP was synthesized from the precursors of LiOH, NH4H2PO4, and FeSO4.7H2O via hydrothermal method. The LiFePO4 V C composite was formed by adding various vanadium concentration 0, 3, 5, 7 at. and a fix concentration of carbon 4 wt. Thermal analysis STA was used to characterize the formation of LFP and the transition temperature of the composite from which a transition temperature of 681.950C was obtained. X ray diffraction XRD was used to characterize the crystal structure, whereas scanning electron microscope SEM equipped with energy dispersive X ray spectroscopy EDX was used to characterize the morphology and composition of the composite. The conductivity of the composite was examined using electrical impendance spectroscopy EIS.

The XRD results showed that LiFePO4 V C has an olivine structure with Pnmb space group. The SEM EDX results depicted aglomerate particles but most LiFePO4 V has been coated by carbon. EIS test results showed a conductivity of 5.33 x 10 5 S cm for LiFePO4 C with no vanadium and 6.0 x 10 6 S cm for 5 wt. vanadium doped LiFePO4 V C."

"Telah dilakukan sintesis LiFePO4/C sebagai material katoda baterai lithium ion dengan menggunakan metode hidrotermal dari bahan LiOH, NH4H2PO4, FeSO4.7H2O, carbon black dan sukrosa. Proses hidrotermal dilakukan pada suhu reaktor 180⁰C dengan lama waktu penahanan 20 jam. Penambahan karbon dilakukan dengan 2 cara. Pertama menggunakan sukrosa sebagai sumber karbon yang dilarutkan bersama prekusor dan kedua menggunakan carbon black yang ditambahkan setelah proses hidrotermal sebelum proses kalsinasi. Temperatur kalsinasi divariasikan pada 500, 600 dan 750⁰C selama 5 jam. Proses dekomposisi termal dianalisis menggunakan DTA-TGA analyzer, karakterisasi fasa dilakukan dengan XRD, morfologi dengan SEM/EDX, nilai konduktifitas dan kapasitansi material dengan LCR-EIS, dan performa baterai dengan pengujian charge-discharge menggunakan baterai analyzer. Hasil LiFePO4/C yang murni berbentuk flake berhasil disintesis dengan penambahan carbon black 5 wt%, sedangkan untuk penambahan karbon melalui pelarutan sukrosa masih terdapat pengotor Fe3(PO4)2 pada hasil kalsinasi. Temperatur kalsinasi optimal adalah 750⁰C dengan ukuran kristalit 39,7 nm, tebal butiran flake 80 nm dan besar butiran rata-rata 427 nm. Konduktifitas LiFePO4 murni terukur 5 x 10-7 S/cm dan konduktifitas LiFePO4/C adalah 2,23 x 10-4 S/cm yang dihasilkan dari sampel dengan tambahan carbon black 5wt% kalsinasi 750⁰C. Dari pengujian charge/discharge didapatkan siklus terbaik dihasilkan oleh sampel LiFePO4/C yang dikalsinasi 750⁰C yang stabil dengan tegangan 3,3-3,4 V, kapasitas spesifik dihasilkan pada 0,1 C = 11,6 mAh/g ; 0,3C = 10,78 mAh./g dan 0,5 C = 9,45 mAh/g.

---

LiFePO4/C has been succesfully synthesized through hydrothermal method from LiOH, NH4H2PO4, and FeSO4.7H2O as starting materials and either carbon black or sucrose as carbon source used as cathode material for lithium ion batteries. In this work, hydrothermal reaction temperature was at 180C for 20 hours.Carbon sources were added in two routes. Firstly, sucrose solution was mixed with precursor solution before hydrothermal reaction. Secondly carbon black was added after hydrothermal reaction before calcination process. Calcination temperatures were performed at 500, 600, and 750C each for 5 hours. Thermal decomposition process was analyzed using DTA-TGA analyzer, phases and morphological were characterized by using XRD and SEM/EDX measurement, conductivity and electrical capacity were characterized by EIS measurement, and batteries performance were tested with charge discharge testing by battery analyzer. Pure LiFePO4/C flake shaped was successfully synthesized with the addition of 5 wt% carbon black, while the addition of carbon through the dissolution of sucrose still contained impurity from Fe3(PO4)2 in calcination product. Optimal calcination temperature was obtained at 750⁰C with crytallite size of 39.7 nm, flake particles diameter of 80 nm with particles average length of 427 nm. Pure LiFePO4 conductivity was measured to be 5 x 10-7 S/cm and conductivity LiFePO4/C was 2.23 x 10-4 S/cm produced from samples with carbon black addition of 5 wt% and calcined at 750⁰C. Charge/discharge cycles test showed that best battery performance was obtained from the sample with carbon black of 5wt% calcined at 750⁰C, with a stable voltage 3.3 to 3.4 V, specific capacity of 0.1 C = 11.6 mAh/g ; 0.3C = 10.78 mAh./g dan 0.5 C = 9.45 mAh/g."

"Lithium Ferro Phosphate (LiFePO4) adalah kandidat yang menjanjikan sebagai bahan sumber energi elektrik yang ramah lingkungan. Penambahan Ni komposit dalam baterai berbasis Li-ion dapat meningkatan performa dari baterai LiFePO4. Dalam penelitian ini, LiFePO4 akan disintesis dengan menggunakan Fe2O3, H3PO4, dan LiOH melalui cara solid-state dan dilakukan perlakuan panas yaitu sintering. Setelah itu, prekursor dikompositkan dengan tiga variasi penambahan konten Nikel dalam % berat, yaitu 5, 7 dan 10% melalui metode solid-state dengan ball mill diberi label LFP/5-Ni, LFP/7.5-Ni dan LFP/10-Ni. Karakterisasi dilakukan menggunakan XRD dan SEM untuk mengamati efek penambahan Nikel pada struktur dan morfologi sampel yang dihasilkan.

---

Lithium Ferro Phosphate (LiFePO4) is a promising candidate as an environmental friendly electric energy sources. The addition of Nickel composite in Lithium-ion battery based can enhance the performance of LiFePO4 batteries. In this experiment, LiFePO4 was synthesized using Fe2O3, H3PO4, and LiOH by solid-state method and heat treated with sintering process. After that, the precursor were composited with the various Nickel composition, in % wt, 5, 7.5 and 10% with solid-state method by using ball mill and labeled as LFP/5-Ni, LFP/7.5-Ni and LFP/10-Ni respectively. The characterizations were made using XRD and SEM testing. These were performed to observe the effect of Nickel addition on structure and morphology of the resulting samples."

"[Telah dilakukan peningkatan konduktivitas listrik LiFePO4 dengan metode penambahan material logam nano Cu dan CNTs. Metode ini menjadi pilihan yang menarik karena mudah dan murah dalam proses pembuatannya. Proses sintesis dilakukan dengan mencampur serbuk LiFePO4 (komersil) dengan variasi presentase berat nano tembaga (komersil) 0, 1, 3, 5, 7 wt. % dan 5 wt. % nano karbon (komersil)kemudian di proses vacuum mixing dan film applicator. Pengujian XRD, SEM dan EDX dilakukan pada serbuk yang diterima untuk mengkonfirmasi fasa, ukuran butir serta ada tidaknya impurities. Hasil XRD dan EDX pada serbuk nano Cu menunjukkan bahwa telah terjadi oksidasi dan terbentuk menjadi CuO dan Cu2O, serta ditemukanadanya impurities elemen S sebesar 8.5 wt. %. Komposisi fasa yang dihasilkan dari proses penambahan didapat dari menganalisis pola difraksi XRD menunjukkan bahwa fasa yang terbentuk adalahLiFePO4 namun ditemukan adanya impurities berupa Cu4O3 pada variasi penambahan 80 wt. % LiFePO4, 5 wt. % Cu, 5 wt. % C, dan 10 wt. % PVDF. Konduktivitas listrik diuji material katoda LiFePO4 dengan EIS, dan hasil uji menunjukkan bahwa konduktivitas listrik LiFePO4 meningkat seiiring dengan penambahan nano Cu namun tidak terlalu signifikan (dalam satu orde), hal ini dikarenakan efek oksidasi pada Cu.Pada variasi penambahan nano C dan nano Cu terjadi peningkatan sebesar 3 orde dengan nilai konduktivitas sebesar 8.4 x 10-5 S/cm pada variasi penambahan 80 wt. % LiFePO4, 5 wt. % Cu, 5 wt. % C. Penambahan nano karbon pada LiFePO4 lebih efektif dalam peningkatan konduktivitas dibandingkan dengan penambahan nano Cudikarenakan efek oksidasi pada Cu yang tidak dapat dihindari. Morfologi material katoda dan distribusi nano Cu dan nano karbon dianalisis menggunakan SEM/EDX, menunjukkan material yang dicampur pada variasi penambahan nano Cu cukup homogen, struktur butir spherical, sedangkan pada variasi penambahan nano Cu dannano karbon struktur butir polyhedral dengan ukuran butir berada pada rentang 100- 500 nm. Struktur butir ini mempengaruhi hasil cole plot dimana pada variasi penambahan Cu terbentuk semicircle sedangkan pada penambahan nano C tidak;Improved of Electrical conductivity of LiFePO4 with the method of adding Cu Nano metal material and CNTs has been done. This method is an attractive option because it is easy and inexpensive in the manufacturing process. Synthesis process isdone by mixing the powder LiFePO4 (commercial) with a variation of the percentage by weight of Nano copper (commercial) 0, 1, 3, 5, 7 wt. % and 5 wt. % CNTs (commercial) and then process in vacuum mixing and film applicator. Testing XRD, SEM and EDX performed on the powder to confirm the phase, grain size and the presence or absence of impurities. Results of XRD and EDX on Nano Cu powder showed that there had been oxidation and formed into CuO and Cu2O, and discovered the existence of impurities elements S of 8.5 wt. %.Phase composition as the result from adding process obtained with analyzing the XRD diffraction pattern showed that the phase formed is LiFePO4 yet found any impurities in the form of Cu4O3 on variations LiFePO4 addition of 80 wt. %, 5 wt. % Cu, 5 wt. % C, and 10 wt. % PVDF. The electrical conductivity of LiFePO4 cathode material was tested by EIS, and the results showed that the electrical conductivity of LiFePO4 increased with the addition of Nano-Cu but not too significant (still on the same order), this is because the effects of oxidation on Cu. On the addition of Nano C and Nano Cu variation there is an increase of 3 order with conductivity value 8.4 x 10-5 S / cm at variations LiFePO4 addition of 80 wt.%, 5 wt.% Cu, 5 wt.% C. The addition of CNTs is more effective in LiFePO4 conductivity increase, compared to the additionof Nano-Cu due to the effects of oxidation on Cu are unavoidable. Cathode material morphology and distribution of CNTs and Nano Cu analyzed using SEM / EDX, showed mixed material on the variation of the addition of Nano Cu quite homogenous, spherical grain structure, while the variation of the addition of Nano Cu and CNTs structures polyhedral grains with a grain size in the range 100-500 nm. This affects the grain structure results in a variation of Cole plot where the addition of Cu is formed semicircle, while the addition of Nano C is not.;Improved of Electrical conductivity of LiFePO4 with the method of adding CuNano metal material and CNTs has been done. This method is an attractive optionbecause it is easy and inexpensive in the manufacturing process. Synthesis process isdone by mixing the powder LiFePO4 (commercial) with a variation of the percentageby weight of Nano copper (commercial) 0, 1, 3, 5, 7 wt. % and 5 wt. % CNTs(commercial) and then process in vacuum mixing and film applicator. Testing XRD,SEM and EDX performed on the powder to confirm the phase, grain size and thepresence or absence of impurities. Results of XRD and EDX on Nano Cu powdershowed that there had been oxidation and formed into CuO and Cu2O, and discoveredthe existence of impurities elements S of 8.5 wt. %.Phase composition as the result from adding process obtained with analyzingthe XRD diffraction pattern showed that the phase formed is LiFePO4 yet found anyimpurities in the form of Cu4O3 on variations LiFePO4 addition of 80 wt. %, 5 wt. %Cu, 5 wt. % C, and 10 wt. % PVDF. The electrical conductivity of LiFePO4 cathodematerial was tested by EIS, and the results showed that the electrical conductivity ofLiFePO4 increased with the addition of Nano-Cu but not too significant (still on thesame order), this is because the effects of oxidation on Cu. On the addition of Nano Cand Nano Cu variation there is an increase of 3 order with conductivity value 8.4 x 10-5 S / cm at variations LiFePO4 addition of 80 wt.%, 5 wt.% Cu, 5 wt.% C. The additionof CNTs is more effective in LiFePO4 conductivity increase, compared to the additionof Nano-Cu due to the effects of oxidation on Cu are unavoidable. Cathode materialmorphology and distribution of CNTs and Nano Cu analyzed using SEM / EDX,showed mixed material on the variation of the addition of Nano Cu quite homogenous,spherical grain structure, while the variation of the addition of Nano Cu and CNTsstructures polyhedral grains with a grain size in the range 100-500 nm. This affects thegrain structure results in a variation of Cole plot where the addition of Cu is formedsemicircle, while the addition of Nano C is not., Improved of Electrical conductivity of LiFePO4 with the method of adding CuNano metal material and CNTs has been done. This method is an attractive optionbecause it is easy and inexpensive in the manufacturing process. Synthesis process isdone by mixing the powder LiFePO4 (commercial) with a variation of the percentageby weight of Nano copper (commercial) 0, 1, 3, 5, 7 wt. % and 5 wt. % CNTs(commercial) and then process in vacuum mixing and film applicator. Testing XRD,SEM and EDX performed on the powder to confirm the phase, grain size and thepresence or absence of impurities. Results of XRD and EDX on Nano Cu powdershowed that there had been oxidation and formed into CuO and Cu2O, and discoveredthe existence of impurities elements S of 8.5 wt. %.Phase composition as the result from adding process obtained with analyzingthe XRD diffraction pattern showed that the phase formed is LiFePO4 yet found anyimpurities in the form of Cu4O3 on variations LiFePO4 addition of 80 wt. %, 5 wt. %Cu, 5 wt. % C, and 10 wt. % PVDF. The electrical conductivity of LiFePO4 cathodematerial was tested by EIS, and the results showed that the electrical conductivity ofLiFePO4 increased with the addition of Nano-Cu but not too significant (still on thesame order), this is because the effects of oxidation on Cu. On the addition of Nano Cand Nano Cu variation there is an increase of 3 order with conductivity value 8.4 x 10-5 S / cm at variations LiFePO4 addition of 80 wt.%, 5 wt.% Cu, 5 wt.% C. The additionof CNTs is more effective in LiFePO4 conductivity increase, compared to the additionof Nano-Cu due to the effects of oxidation on Cu are unavoidable. Cathode materialmorphology and distribution of CNTs and Nano Cu analyzed using SEM / EDX,showed mixed material on the variation of the addition of Nano Cu quite homogenous,spherical grain structure, while the variation of the addition of Nano Cu and CNTsstructures polyhedral grains with a grain size in the range 100-500 nm. This affects thegrain structure results in a variation of Cole plot where the addition of Cu is formedsemicircle, while the addition of Nano C is not.]"

"Pengembangan baterai listrik sebagai sumber energi utama untuk electricity-vehicle menjadi fokus utama dalam industri otomotif terkini. Salah satu dari sumber energi listrik yang paling banyak dikembangkan adalah baterai ion lithium. Komponen penting pada Baterai Ion-Lihium yakni katoda merupakan salah satu komponen yang banyak dilakukan pengembangan pada bidang industri, katoda yang paling banyak digunakan pada pengembangan industri baterai ion-lihium adalah LiCoO2 dan NMC 622. NMC material memiliki keuntungan dibandingkan LiCoO2 terutama dalam keseimbangan energy density, power capability, dan cost dari produk. Material NMC juga memiliki kesetimbangan termal yang lebih baik dibandingkan LiCoO2 sehinga lebih safety dalam proses sintesis material. Penelitian kali ini, menggunakan NMC 622 sebagai katoda utama dengan disintesis menggunakan metode solution combustion (SCS) dengan variasi suhu sintering. Metode solution combustion digunakan karena metode ini sederhana dalam pengunaannya, cost yang cenderung murah, dan proses sintesis tidak memakan waktu yang lama. Untuk mendapatkan data penelitian, mengenai performa terbaik pada hasil sisntesis dilakukan variasi suhu sintering pada 3 variasi suhu 700 oC, 800 oC, dan 900 oC. Hasil dari uji SEM-EDS menyatakan bahwa material memiliki distribusi partikel yang baik. Hasil XRD menunjukkan hasil struktur material yang berbentuk hexagonal. NMC 622 800 oC memiliki kapasitas 137.24787 mAh/g, NMC 622 700 oC sebesar 101.56644 mAh/g dan kapasitas NMC 622 900 oC sebesar 66.61218 mAh/g.

---

The development of electric batteries as the main energy source for electricity-vehicles is a major focus in the current automotive industry. One of the most widely developed sources of electrical energy is the lithium-ion battery. An important component in the Ion-Lihium Battery, cathode is one of the components that is widely developed in the industrial field, the cathode that is most widely used in the development of the ion-lihium battery industry is LiCoO2 and NMC 622. NMC material has advantages over LiCoO2 especially in the balance of energy density, power capability, and cost of the product. NMC material also has a better thermal equilibrium than LiCoO2 so that it is more safety in the material synthesis process. This research uses NMC 622 as the main cathode by synthesizing it using the solution combustion (SCS) method with variations in sintering temperature. The solution combustion method is used because this method is simple in its use, the cost tends to be cheap, and the synthesis process does not take a long time. To obtain research data, regarding the best performance in the synthesis results, sintering temperature variations were carried out at 3 temperature variations of 700 oC, 800 oC, and 900 oC. The results of the SEM-EDS test state that the material has a good particle distribution. XRD results show the results of hexagonal material structure. NMC 622 800 oC has a capacity of 137.24787 mAh/g, NMC 622 700 oC of 101.56644 mAh/g and a capacity of NMC 622 900 oC of 66.61218 mAh/g."

"Litium Ferro Phosphate, LiFePO4 (LFP) adalah kandidat yang menjanjikan sebagai bahan katoda baterai lithium ion. Dalam penelitian ini, LFNP/C disintesis dengan metode solid-state dari precursor LFP, Nikel menjadi variasi penambahan konten LFP dalam bentuk doping, yaitu, 6, 7,5 dan 9%, diberi label sampel LFNP/C-Ni6%, LFNP/C-Ni7.5% dan LFNP/C-Ni9%. Karakterisasi dilakukan menggunakan XRD, SEM, EDX, dan MAPPING. Ini dilakukan untuk mengamati efek penambahan Nikel pada struktur, morfologi, dan komposisi sampel. Hasil penelitian menunjukkan bahwa persentase optimum doping Nikel adalah 7.5% karena telah menunjukan hasil yang memuaskan di performa CV,CD, dan EIS dengan ukuran kristal 76.93 nm. Dalam pengujian cyclic voltametry, konduktivitas dan kapasitas sampel meningkat dan disebabkan oleh penambahan Nikel pada LFP.

---

Lithium Ferro Phosphate, LiFePO4 (LFP) is a promising candidate as a cathode material for lithium ion batteries. In this study, LFNP / C was synthesized by the solid-state method of the LFP precursors, Nickel became a variation of LFP content addition in the form of doping, namely, 6, 7.5 and 9%, labeled LFNP / C-Ni6% sample, LFNP / C-Ni7.5% and LFNP / C-Ni9%. Characterization was done using XRD, SEM, EDX, and MAPPING. This was done to observe the effect of adding Nickel to the structure, morphology, and composition of the sample. The results showed that the optimum percentage of Nickel doping was 7.5% because it had shown satisfactory results in the performance of CV, CD, and EIS with a crystal size of 76.93 nm. In cyclic voltametry testing, the conductivity and capacity of the sample increases and is caused by the addition of Nickel to LFP."