Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 19976 dokumen yang sesuai dengan query
cover
Fajri Ashfi Rayhan
"Ice slurry technology is highly favored to maintain the freshness of fish, as the cooling capacity of ice slurry is higher than that of flaked ice, tubular ice, plate ice, and block ice. One important part of an ice-slurry system is the ice generator. A mechanical scraper is the easiest type of ice-slurry generator to fabricate, because mechanical scrapers use only one type of material, such as stainless steel. The purpose of this research was to develop a prototype ice-slurry generator and analyze its performance. To enable comparison of their performance, both the R-22 and R-290 refrigerants were used as the working fluids in the refrigeration system. The study observed the time necessary to form ice and the scraper’s ability to scrape the ice on the inner surface of the evaporator. The best system included faster ice-slurry generation and a durable generator that did not freeze up. Four combinations of scraper RPM and pump RPM varied speeds from low to high. The results showed that using R-290 refrigerant and lower RPM speeds for both the scraper and the pump generated ice slurry in a shorter time."
Depok: Faculty of Engineering, Universitas Indonesia, 2017
UI-IJTECH 8:7 (2017)
Artikel Jurnal  Universitas Indonesia Library
cover
Niken Dhanitya
"Salah satu usaha yang nasional adalah dengan teknologi ice slurry. Ice slurry generator dengan menggunakan scraper saat ini menjadi teknologi yang banyak dikembangkan dan digunakan secara luas. Penelitian ini dilakukan dengan menggunakan dua jenis scraper yang berbeda yaitu scraper simetrik dan asimetrik untuk menghasilkan ice slurry berbahan dasar air laut. Performa dari kedua jenis scraper tersebut kemudian dinilai dari segi kecepatan penurunan suhu dan kecepatan pembentukan ice slurry dengan variasi putaran pompa dan putaran scraper yang berbeda. Dengan mengkombinasikan 12 variasi putaran pompa dan scraper, didapatkan hasil putaran yang optimum untuk pembentukan ice slurry pada masing- masing tipe scraper adalah pada putaran pompa 2074 rpm dan putaran scraper 468 rpm.

One of the efforts to escalate national fish industry is by developing fish preservation technology with ice slurry. Ice slurry technology is highly favored for its advantage in maintaining fish freshness longer than using flake ice. The scraped- surface ice slurry generator is currently the most technologically developed and widely accepted technology in ice slurry generation. This study is using two types of different scraper, asymmetric and symmetric type with sea water as raw material. Performance of both scraper types will then be rated by its cooling rate and ice slurry generation rate with different variations of pump and scraper rotation. Combining 12 pump and scraper rotation variations and processing the data, it is found that the optimum pump and scraper rotation for ice slurry generation are 2074 rpm and 468 rpm, respectively.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S63525
UI - Skripsi Membership  Universitas Indonesia Library
cover
Yafi Rahmad Oktafian
"Ice slurry merupakan media pendingin ikan dengan kualitas pendinginan yang merata, partikel es yang tidak merusak ikan,dan suhu pendinginan dibawah 0 derajat. Hal ini membuat nelayan dapat menjaga kualitas ikan agar tetap segar dan tidak mengalami pembusukan selama berada di atas kapal. Penelitian kali ini akan bertujuan untuk mengimplementasikan ice slurry generator untuk kapal ikan 25 GT. Penelitian ini mencakup penggambaran layout untuk peletakan Ice slurry generator dan analisa investasinya dengan mencari nilai break even point, net present value, dan internal rate of return. Pemasangan ice slurry generator bertujuan untuk memenuhi kebutuhan es pada kapal ikan 25 GT sebanyak 465 kg/hari. Kapal pada penelitian ini memiliki panjang 16.5 m, lebar 4.47 m dan tinggi 1.69 m dengan displacement 50104 Ton. Kapal ini terdiri dari 2 palkah ikan yang nantinya akan diisi ikan yang didinginkan oleh ice slurry. Hasil dari penelitian ini adalah gambar layout peletakan ice slurry generator di kapal ikan dan hasil analisa investasinya. Dari hasil analisa investasi didapat bahwa pemilik kapal ikan 25 GT dengan ice slurry generator dapat mencapai titik break even point pada trip ke 88 atau selama 2 tahun 6 bulan dari awal investasi dilakukan. Nilai net present value dengan bunga 12 % yang didapatkan sebesar Rp.1.946.895.697 yang berarti investasi layak dilakukan (NPV>0). Nilai IRR yang didapat dari penelitian ini sebesar 35.58 % yang artinya investasi layak dilakukan karena lebih besar dari pada bunga pinjaman (12%).

Ice slurry is a fish cooling media with an even cooling quality, ice particles that do not damage fish, and cooling temperatures below 0 degrees. This makes the fishermen can maintain the quality of the fish so that it remains fresh and does not experience decay while on the boat. This research will aim to implement an ice slurry generator for 25 GT fishing vessels. This study includes a description of the layout for the laying of the Ice slurry generator and investment analysis by finding the break even point value, net present value, and internal rate of return. The installation of the ice slurry generator aims to meet the needs of ice on a 25 GT fishing vessel totaling 465 kg / day. The ship in this study has a length of 16.5 m, width 4.47 m and height 1.69 m with displacement of 50104 tons. This ship consists of 2 fish hatches which will later be filled with fish which are cooled by ice slurry. The results of this study are the layout picture of laying ice slurry generator on a fishing vessel and the results of investment analysis. From the investment analysis it is found that the owner of a 25 GT fishing vessel with an ice slurry generator can reach the break even point on trip 88 or for 2 years and 6 months from the initial investment. The net present value with an interest of 12% is Rp. 1.946.895.697 which means that the investment is feasible (NPV> 0). The IRR value obtained from this study is 35.58% which means the investment is feasible because it is greater than the loan interest (1).
"
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ramadhan Rahmat Riadi
"Pendinginan, pada bidang perikanan, memiliki pengaruh yang signifikan terhadap kualitas tangkapan ikan yang juga berakibat pada keuntungan yang akan didapat kelak. Salah satu cara untuk menjaga kualitas hasil tangkapan ikan adalah dengan cara diaplikasikannya ice slurry sebagai media pendingin. Ice slurry, dibandingkan dengan es balok konvensional, memiliki performa pendinginan yang lebih baik dikarenakan interaksi antara permukaan hasil tangkapan dengan media pendinginan yang lebih luas. Produksi ice slurry, pada penelitian ini, menggunakan dua evaporator dengan tujuan untuk memaksimalkan performa perpindahan panas pada generator ice slurry. Evaporator I berfungsi untuk menurunkan temperatur air laut dari 30oC menuju ke 5oC sedangkan evaporator II berfungsi untuk menurunkan temperatur air laut dari 5oC menuju ke -2oC yang merupakan titik beku air laut dengan bantuan scraper. Ditargetkan bahwa ice slurry yang dihasilkan memiliki konsentrasi massa es sebesar 30%. Dengan digunakannya dua evaporator, dimensi perangkat yang diperoleh dapat berukuran ringkas, yaitu dengan panjang total yang tidak melebihi satu meter. Selain itu, ice slurry diajukan agar dijual dengan harga Rp250,00 per kilogramnya dengan tujuan agar harganya sangat terjangkau oleh para nelayan. Dengan perhitungan break even point (BEP), didapat bahwa investasi produksi ice slurry ini akan menghasilkan keuntungan pada sekitar bulan ke 15 atau ke 16 sejak dioperasikannya proses pembuatan ice slurry ini.

Cooling, on fisheries, has significant impact regarding to the quality of fish catching and also has impact on profit that would be gotten later. One of many manners to keep the quality of fish catching is by ice slurry application as cooling medium. Ice slurry, compared with conventional block ice, has better cooling performance due to its larger interaction between cooling media and fish product surface. Ice slurry production, on this study, uses two units of evaporator as an objective to maximize heat transfer performance on ice slurry generator. Evaporator I's function is to decrease the temperature of sea water from 30oC to 5oC whereas evaporator II's function is to decrease the temperature of the sea water from 5oC to -2oC which is the freezing point of sea water. Scraper is applied to evaporator II as a mechanical aid to increase evaporator II's heat transfer performance. It is aimed that the ice concentration of ice slurry is around 30%. Regarding of using two evaporators, the dimension of devices that is obtained could be relatively compact, with their total length do not exceed one meter. Furthermore, produced ice slurry is proposed to be sold by Rp250,00 per kilogram regarding to its affordability by fishermen. With the calculated of break even point (BEP), it is obtained that the investment of this ice slurry production would yield profits on around the 15th or the 16th month since the beginning of ice slurry production."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muhammad Hizrian Ayasy
"Bubur es (ice slurry) merupakan media pendingin yang paling cepat dan efisien. Dalam pembuatan ice slurry, refrigeran dibutuhkan sebagai media pendingin. R-290 dan R-404A adalah refrigeran yang umum digunakan pada siklus pendinginan dengan skala kecil seperti ruangan, kulkas, dan lain-lain. R-290 (propana) sudah dapat diproduksi di dalam negeri, tidak merusak ozon, tidak memerlukan pelumas, tidak meningkatkan Ozone Depletion Potential (ODP), tidak meningkatkan Global Warming Potential (GWP), momen torque pada kompresor menjadi turun dan proses pencapaian refrigeran dingin lebih cepat. Dalam penelitian ini dilakukan kajian terkait kinerja refrigeran R-290 dan dibandingkan dengan refrigeran R-404 yang sudah sangat umum digunakan di pasaran. Kajian yang dilakukan mempertimbangkan aspek desain dari ice slurry generator, serta peran evaporator pada sistem ice slurry generator. Penambahan evaporator pada ice slurry generator dapat membuat proses pembentukan ice slurry lebih singkat relatif terhadap ice slurry generator dengan 1 evaporator (single evaporator). Hasil rancangan ice slurry generator yang diperoleh telah memenuhi kriteria dasar dalam hal perancangan alat penukar kalor. Nilai koefisien perpindahan kalor total pada evaporator utama hasil rancangan melebihi nilai koefisien perpindahan kalor total yang dibutuhkan, sedangkan pada pre-cooling nilai koefisien perpindahan kalor rancangan sudah seimbang dengan nilai koefisien perpindahan kalor asumsi dengan faktor koreksi di bawah 20%. Pada rancangan evaporator utama, koefisien perpindahan kalor yang menggunakan refrigeran R290 memiliki nilai yang lebih besar dibandingkan dengan rancangan evaporator utama menggunakan refrigeran R404A. Tidak ada perbedaan antara hasil perhitungan dimensi pada evaporator utama yang menggunakan refrigeran R290 dan refrigeran R404A. Pada hasil perkiraan harga fabrikasi alat dengan Metode Guthrie didapatkan bahwa rancangan ice slurry generator menggunakan refrigeran R290 memiliki nilai investasi yang lebih rendah dibandingkan dengan rancangan menggunakan refrigeran R404A.

Ice slurry is the fastest and most efficient cooling medium. In the manufacture of ice slurry, refrigerant is needed as a cooling medium. R-290 and R-404A are refrigerants that are commonly used in small-scale refrigeration cycles such as rooms, refrigerators, and others. R-290 (propane) can be produced domestically, does not destroy ozone, does not require lubricants, does not increase the Ozone Depletion Potential (ODP), does not increase the Global Warming Potential (GWP), the torque moment on the compressor decreases and the process of achieving cold refrigerant is achieved. faster. In this study, a study was conducted regarding the performance of refrigerant R-290 and compared it with refrigerant R-404 which is very commonly used in the market. This study considers the design aspects of the ice slurry generator, as well as the role of the evaporator in the ice slurry generator system. The addition of an evaporator to the ice slurry generator can make the ice slurry formation process shorter relative to an ice slurry generator with 1 evaporator (single evaporator). The results of the ice slurry generator design obtained have met the basic criteria in terms of designing a heat exchanger. The total heat transfer coefficient value in the main evaporator designed exceeds the required total heat transfer coefficient value, while in pre-cooling the design heat transfer coefficient value is balanced with the assumed heat transfer coefficient value with a correction factor below 20%. In the main evaporator design, the heat transfer coefficient using R290 refrigerant has a greater value than the main evaporator design using R404A refrigerant. There is no difference between the results of the dimension calculation on the main evaporator using refrigerant R290 and refrigerant R404A. In the estimation results of the tool fabrication price using the Guthrie method, it is found that the design of the ice slurry generator using R290 refrigerant has a lower investment value than the design using R404A refrigerant.
"
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Andy Kristian
"Ice slurry merupakan teknologi alternatif terbaik dari semua media pendingin dalam menjaga kesegaran ikan. Hal ini karena ikan didinginkan oleh air laut berfase kristal es dengan temperatur dibawah 0 ? dan strukturnya tidak merusak ikan. Modifikasi evaporator dengan bearing guna memperkecil friksi dan kebisingan. Penggunaan propane sebagai media pendingin juga dapat mempercepat waktu pembentukan ice slurry serta refrigerant yang ramah lingkungan. Tujuan dari penelitian ini adalah untuk mencari pengaruh modifikasi evaporator dan menganalisis kinerja dari generator dengan variasi salinitas air laut. Semakin tinggi salinitas air laut maka semakin rendah suhu ice slurry. Tetapi lebih tinggi salinitas belum tentu efisien dari segi daya pembentukan ice slurry yang dibutuhkan untuk mendinginkan ikan, karena hasil tangkapan rata-rata laut perlu suhu pendinginan antara -1 sampai -2 ?. Parameter dalam penelitian ini adalah production rate dan kemampuan scraper memecah es di evaporator. Production rate tertinggi generator ice slurry generasi ke-5 pada penelitian ini berada pada putaran 1064 RPM pompa flowrate 1.8 liter/menit dan 334.5 RPM scraper dengan salinitas 10 ppt yaitu 0.03 liter/Wh.

Ice slurry technology is the best alternative of all the cooling medium in maintaining the freshness of the fish. This is because the fish is cooled by sea water ice crystals gradually with the temperature below 0 and its structure does not damage the fish 39 s body. Modifications evaporator with bearings to reduce friction and noise. The use of propane as a refrigerant can also accelerate the formation of ice slurry and environmentally friendly refrigerant. The purpose of this study was to determine the effect of evaporator modification and analyze the performance of the generator with seawater salinity variations. The higher the salinity of sea water, the lower the temperature of the ice slurry. However the higher salinity may not be efficient in terms of power form a slurry of ice needed to cool fish, because the average catches of sea require refrigeration temperatures between 1 to 2 . The parameters in this study is the production rate and the scraper ability to break the ice in the evaporator. In this study, the highest production rate of ice slurry generator 5th generation are at 1064 RPM rotation pump flowrate 1.8 liter minute and 334.5 RPM scraper with a salinity of 10 ppt is 0.03 liter Wh."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S62745
UI - Skripsi Membership  Universitas Indonesia Library
cover
Mardiansyah Pratama
"ABSTRAK
Penggunaan es dalam mengawetkan ikan agar tetap segar bukanlah hal baru dalam dunia perikanan. Es bubur adalah media pendingin yang baik untuk mengawetkan ikan. Es slurry dapat menjaga kesegaran dan menjaga ikan agar tidak mudah busuk karena es slurry dapat menghambat bakteri yang ada pada ikan. Penelitian ini dilakukan untuk mengetahui perbandingan kinerja dari ice slurry generator yang dirancang sebelumnya dengan yang baru. Dimana pada desain baru ini dilakukan perubahan pada daya condensing unit yang digunakan yaitu 2 PK dengan kondisi variasi salinitas air laut yang digunakan sebesar 10ppt, 20ppt dan 30ppt. Dari pengambilan data didapatkan bahwa laju produksi dan nilai daya alat yang paling optimum diperoleh pada salinitas air laut 10ppt dengan hasil masing-masing 0,239 Ton/12Hours dan 1090,3 Wh. Hasil dari bubur es ini digunakan untuk mendinginkan ikan selama perjalanan di dalam cooler box mobil dari TPI Binuangen menuju pasar ikan Rangkasbitung yang memakan waktu 3 jam perjalanan. Dari pengujian dan penelitian didapatkan hasil Cooling Load sebesar 4,5 kW atau 1,28 TR, dibutuhkan sekitar 145 kg Ice Slurry untuk menjaga suhu ikan selama perjalanan dengan suhu akhir ikan sebesar 0,29°C.
ABSTRACT
The use of ice in preserving fish to keep it fresh is not new in the world of fisheries. Ice porridge is a good cooling medium for preserving fish. Slurry ice can maintain freshness and keep fish from rotting easily because slurry ice can inhibit bacteria in fish. This research was conducted to compare the performance of the previously designed ice slurry generator with the new one. Where in this new design, changes are made to the condensing unit power used, namely 2 PK with conditions of seawater salinity variations used of 10ppt, 20ppt and 30ppt. From the data collection, it was found that the production rate and the most optimum tool power value were obtained at seawater salinity of 10ppt with the results respectively 0.239 Ton/12Hours and 1090.3 Wh. The result of this ice slurry is used to cool the fish during the journey in the car cooler box from TPI Binuangen to the Rangkasbitung fish market which takes 3 hours of travel. From testing and research, it was found that the Cooling Load was 4.5 kW or 1.28 TR, it took about 145 kg of Ice Slurry to maintain the temperature of the fish during the trip with the final temperature of the fish at 0.29°C."
Depok: Fakultas Teknik Universitas Indonesia , 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Farhan Fabian Rasyid
"Ice slurry merupakan media pendingin produk perikanan yang efektif dan efisien dibandingkan dengan media es balok yang luas digunakan oleh nelayan-nelayan di Indonesia. Penggunaan ice slurry sebagai media pendingin ikan menghasilkan performa pendinginan yang optimum karena memiliki partikel kecil yang mampu menjangkau area yang lebih luas dengan tidak merusak produk perikanan yang didinginkan. Penggunaan ice slurry generator di atas kapal menjadi salah satu solusi dalam menggantikan media es balok. Penelitian ini memiliki tujuan untuk mengetahui apakah stabilitas kapal yang disimulasikan pada nelayan (eksisting) dan perencanaan aman dan mengetahui desain peletakan ice slurry generator yang optimum terhadap performa stabilitas. Penelitian ini mencakup analisis solusi terhadap permasalahan yang dialami nelayan, perhitungan kapasitas ice slurry, penggambaran sistem alir ice slurry generator, perhitungan berat ice slurry generator, perhitungan pembebanan kapal dan analisa stabilitas kapal. Pengimplementasian ice slurry generator pada kapal ikan bertujuan untuk memenuhi kebutuhan ice slurry selama 4 hari beroperasi sebanyak 1,29 ton dengan jumlah tangkapan yang diharapkan adalah 3 ton. Kapal ikan 25 GT didesain dengan 2 palkah muat yang nantinya diisi oleh hasil tangkapan dan ice slurry sebagai media pendingin. Hasil dari penelitian ini adalah analisis stabilitas pada berbagai macam kondisi yang disimulasikan. Dari hasil analisis stabilitas yang sudah dilakukan didapatkan bahwa stabilitas kapal operasional pada nelayan (eksisting) dan perencanaan aman secara aturan IMO. Sementara pada analisa stabilitas desain peletakan ice slurry generator didapatkan bahwa desain peletakan ice slurry generator yang diletakan di bawah memberikan performa stabilitas yang lebih baik dibandingkan dengan desain peletakan ice slurry generator di atas geladak utama dan ice slurry generator di bawah geladak utama dengan condensing unit diletakan di atas

Ice slurry is an effective and efficient cooling media for fishery products compared to ice cube media which is widely used by fishermen in Indonesia. The use of ice slurry as a fish cooling medium results in optimum cooling performance because it has small particles that are able to reach a wider area without damaging the cooled fishery product. The use of an ice slurry generator on board is one of the solutions in replacing block ice media. This study aims to determine whether the stability of the simulated boat for fishermen (existing) and planning is safe and to determine the design of the optimum ice slurry generator placement for stability performance. This research includes analysis of solutions to problems experienced by fishermen, calculation of ice slurry capacity, depiction of the flow system of the ice slurry generator, calculation of the weight of the ice slurry generator, calculation of ship loading and analysis of ship stability. The implementation of ice slurry generators on fishing boats aims to meet the demand for ice slurry for 4 days of operation of 1.29 tons with the expected catch of 3 tons. The 25 GT fishing boat is designed with 2 cargo holds which will be filled with the catch and ice slurry as a cooling medium. The result of this research is stability analysis in various simulated conditions. From the results of the stability analysis that has been carried out, it is found that the stability of operational vessels for fishermen (existing) and planning is safe according to IMO regulations. Meanwhile, in the stability analysis of the design for placing the ice slurry generator, it was found that the design for placing the ice slurry generator placed below provided better stability performance compared to the design for placing the ice slurry generator above the main deck and the ice slurry below main deck with the condensing unit placed above the main deck."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
"Trimethylolethane (TME) trihydrate slurry is a proper phase-change material for latent heat transportation in cooling systems since it has excellence heat transfer performance and high thermal capacity...."
Artikel Jurnal  Universitas Indonesia Library
cover
Kuswantoro
"Kenaikan temperatur udara akibat penipisan lapisan ozon dan pemanasan global merupakan salah satu isu yang saat ini tengah menarik perhatian dunia. Penggunaan refrigerant berbasis chlorin (CFCs dan HCFCs) dan HFCs merupakan salah satu penyebab utamanya sehingga mendorong negara-negara industri untuk sepakat menetapkan masa akhir penggunaan refrigerant ini sebagaimana yang tertuang dalam protokol Montreal dan Kyoto. Hal ini membuat refrigerant alami seperti amonia dan hidrokarbon kembali menjadi populer, namun karena pada umumnya refrigerant ini dapat terbakar dan beracun membuat sistem refrigerasi tidak langsung lebih aman diterapkan untuk sistem ini.
Sistem refrigerasi tidak langsung menggunakan refrigerant kedua yang sifatnya aman terhadap manusia dan lingkungan. Ice slurry merupakan salah satu refrigerant kedua yang sangat menarik dikarenakan kapasitas panasnya yang besar akibat pemanfaatan kalor laten dan dapat diaplikasikan untuk temperatur sangat rendah. Masalah yang sering muncul pada pembuatan ice slurry ialah kecenderungan es untuk menempel pada dinding perpindahan kalor sehingga di daerah dekat dinding terdapat lapisan yang memiliki konsentrasi es yang lebih tinggi dari titik lainnya, lapisan ini biasa disebut sebagai lapisan mushy. Adanya lapisan es ini akan meningkatkan resistansi thermal sistem. Pada umumnya lapisan mushy ini dibersihkan dengan cara disapu menggunakan alat mekanik yang disebut scraper.
Penelitian ini bertujuan untuk membuat scraper yang dapat dipasangkan pada auger yang telah ada dan melihat pengaruhnya terhadap laju perpindahan kalor dan kepadatan es pada ice slurry yang terbentuk. Berdasarkan pengukuran temperatur larutan selama 200 menit, terhitung laju perpindahan kalor rata-rata untuk auger yang telah dilengkapi scraper mengalami peningkatan sebesar 4% pada fase liquid dan 93% pada fase liquid-ice terhadap laju perpindahan kalor rata-rata.

Increment change in air temperature as a result of ozone depletion and global warming are issue that attracts world attention these days. The wide use of chlorine base refrigerant (CFCs and HCFCs) and HFCs are one of the major factor that cause it, this fact encourage industrial countries agree to set the phase out of these refrigerant which is written in Montreal and Kyoto protocol. This rule make natural refrigerant like ammonia and hydrocarbon to become attractive again, however because most natural refrigerant are flammable and toxic, indirect refrigeration system are more safe to implemented.
Indirect refrigeration system use secondary refrigerant that safe for human and environment. Ice slurry?s are one of the secondary refrigerants that very attractive because their use of latent heat capacity and able to applied on very low temperature. The problem which often occur in making of ice slurry are the tendency of ice to adhere on heat transfer wall so this area will filled with layer that has higher ice concentration than other area, this layer used to called mushy structure. The present of this ice layer will increase the thermal resistant of a system. Usually this mushy structure wipe mechanically using scraper.
The goal of this research focus on making a scraper that can assembly well with an existing auger and study its effect on heat transfer rate and ice packed of the formed ice slurry. Base on measured solution temperature for 200 minute, the calculated average heat transfer rate for auger with scraper increase about 4% in liquid phase and 93% in liquid-ice phase compared with auger without scraper.
"
Depok: Fakultas Teknik Universitas Indonesia, 2008
S37342
UI - Skripsi Open  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>