Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 130 dokumen yang sesuai dengan query
cover
Handy Chandra
Abstrak :
Delta Sigma ADC (Analog to Digital Converter) adalah salah satu jenis ADC dengan resolusi yang lebih tinggi dibandingkan jenis ADC lainnya. Komponen paling penting dari Delta Sigma ADC adalah Delta Sigma Modulator. Terdapat dua faktor yang mempengaruhi resolusi dari Delta Sigma Modulator yaitu oversampling ratio dan topologi rangkaian. Skripsi ini akan membahas simulasi dan optimasi dari salah satu topologi rangkaian Delta Sigma Modulator yaitu SecondOrder Delta Sigma Modulator untuk mencapai resolusi yang lebih tinggi. Rangkaian SecondOrder Delta Sigma Modulator akan dioptimasi dengan menggunakan topologi fully differential dan dengan menaikkan oversampling ratio agar mencapai resolusi yang lebih tinggi. Kemudian layout integrated circuit dari rangkaian secondorder Delta Sigma Modulator akan dibuat dan disimulasikan untuk melihat performa dari rangkaian. Pada simulasi awal didapatkan resolusi modulator sebesar 8 bit. Kemudian optimasi lebih jauh dilakukan dengan mengubah ? ubah nilai kapasitor dan kapasitansi parasitik pada modulator untuk melihat pengaruhnya terhadap resolusi dari modulator. Dari hasil percobaan optimasi didapatkan dengan mengubah kapasitor C1,C2 menjadi 0,2 pf dan kapasitansi parasitik poly1 ke substrat dari kapasitor C1,C2 menjadi 1 ff, resolusi modulator naik menjadi 15 bit. ......Delta Sigma ADC (Analog to Digital Converter) is one of ADC with high resolution. The most important component of Delta Sigma ADC is Delta Sigma Modulator. There are two factors that influence the resolution of Delta Sigma Modulator, which is oversampling ratio and circuit topology. This thesis discusses about simulation and optimization of one topology of Delta Sigma Modulator called SecondOrder Delta Sigma Modulator to reach better resolution. Second¬ Order Delta Sigma circuit will be optimized using fully differential topology and increasing oversampling ratio. Then, integrated circuit layout of SecondOrder Delta Sigma Modulator will be made and simulated to look at the performance of the circuit. Simulation reveal that modulator?s resolution is 8 bit. Further optimization will be done by changing the value of capacitor and parasiticcapacitance to see it?s relation to the resolution of the modulator. After optimization is done, better resolution is achieved with the value of C1,C2 0.2 pf and parasitic capacitance poly1 to substrate from C1,C2 is 1 ff. The new effective resolution achieved is 15 bit.
Depok: Fakultas Teknik Universitas Indonesia, 2011
S769
UI - Skripsi Open  Universitas Indonesia Library
cover
Muthuswamy, Bharathwaj
Abstrak :
This course-based text revisits classic concepts in nonlinear circuit theory from a very much introductory point of view: the presentation is completely self-contained and does not assume any prior knowledge of circuit theory. It is simply assumed that readers have taken a first-year undergraduate course in differential and integral calculus, along with an elementary physics course in classical mechanics and electrodynamics. Further, it discusses topics not typically found in standard textbooks, such as nonlinear operational amplifier circuits, nonlinear chaotic circuits and memristor networks. Each chapter includes a set of illustrative and worked examples, along with end-of-chapter exercises and lab exercises using the QUCS open-source circuit simulator. Solutions and other material are provided on the YouTube channel created for this book by the authors.
Switzerland: Springer Cham, 2019
e20502899
eBooks  Universitas Indonesia Library
cover
Puguh Ngudi Widodo
Abstrak :
Produk sirkit langganan Jaringan Multi Service (JAMUS) adalah produk jasa sirkit langganan digital yang biasanya digunakan untuk komunikasi data maupun suara (voice) secara permanen (dedicated), dengan menggunakan infrastruktur jaringan transmisi terrestrial digital, dan perangkat Intelligent Multiplexer (IMUX). Produk tersebut merupakan produk Divisi Network (DIVNET) yang bukan monopoli. Dibandingkan dengan produk lainnya yang masih monopoli, misalnya jasa long distance, maka strategi pengembangan JAMUS harus berbeda. Apalagi pada saat ini iklim persaingan semakin tajam. Untuk menentukan beberapa altematif strategi kebijakan pengembangan JAMUS, maka beberapa faktor yang harus dipetimbangkan antara lain: kondisi lingkungan strategis perusahaan, kondisi pesaing, dan kondisi produk eksisting. Sedangkan metode analisa yang dipergunakan adalah analisa Strength-Weakness-Opportunity-Threat (SWOT), analisa Boston Consulting Group (BCG), analisa produk, dan analisa persaingan. Hasil dari analisa strategi tersebut didapatkan beberapa alternatif strategi yang selanjutnya dipilih satu atau dua strategi utama dengan menggunakan metode matrik Quantitatif Strategy Planning Matrix (QSPM). Strategi utama tersebut adalah strategi penggabungan antara sirkit langganan JAMUS dengan TELKOMnet Divisi Multimedia, serta strategi pembenahan Sumber Daya Manusia (SDM) dan struktur organisasi.
JAMUS or Jaringan Multi Service is a Digital Leased Circuit Service applied for dedicated data and voice communication. The basic network is digital terrestrial transmission and Intelligent Multiplexer (IMUX) Equipment. Unlike long-distance service, JAMUS is a non-monopoly product offered by Divisi Network (DIVNNET). Therefore the development strategy of JAMUS should be distinguished from the previous product (long distance service) in order to compete with the other competitor. Some factors should be consider in developing some strategy alternatives are internal and external environmental of Divisi Network, competition environment and current product performance. These factors would be analyzed by employing some method as follows: Strength-Weakness-Opportunity-Threat (SWOT) analysis, Boston Consulting Group (BCG) analysis, product analysis and competitor analysis. The results are some strategy alternatives fit with competitive market situation. Then utilizing Quantitatif Strategy Planning Matrix (QSPM) method creates two main strategies, first is "Product bundling of JAMUS and TELKOMNET", and second is "Developing new organization and improving human resources capabilities".
Depok: Fakultas Teknik Universitas Indonesia, 2000
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Nasruddin MN
Abstrak :
ABSTRAK
A micro optical branching circuit [MOBC] array by the use of planar micro lens array and a cubical beam splitter was proposed in a previous study. To study further the performance of the elements of the branching array, the constructed circuit has been implemented by modulating three optical signals on different wave lengths of carrier waves transmitted by LD optical sources. The measurement on coupling efficiency gives a value of 36,4 % which is uniform for the three channels of the branching circuit. The branching circuit also shows a negligible cross-talk on the branched signals. It is summarized that the proposed MOBC implemented by modulated signals can be used in practice. The insertion loss could be reduced by appropriate positioning of each elements to achieve optimum focusing and collimating beams.
1992
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Sulistiana Agung Riyanto
Abstrak :
Tujuan penelitian ini adalah untuk mengetahui karakteristik dari bead penghantar listrik tembaga NYM 3x1,5 yang telah mengalami gangguan hubung singkat listrik dan beban arus berlebih pada beban 800% dari kemampuan hantar arusnya (144 Ampere), serta oleh karena menerima panas dari nyala api langsung pada temperatur 960o C. Spesimen bead yang terbentuk dari akibat gangguan hubung singkat listrik, beban arus berlebih serta akibat pemanasan dengan nyala api langsung tersebut kemudian dilakukan pemeriksaan dan pengujian laboratorium yaitu: pemeriksaan komposisi kimia, pemeriksaan visual, pemeriksaan struktur makro dan strukturmikro, pengujian kekerasan dan pemeriksaan SEM-EDS. Perbedaan karakteristik manik-manik busur (bead) yang terbentuk pada kondisi hubung singkat listrik dan beban arus berlebih adalah pada kondisi hubung singkat listrik, titik kerusakan terlokalisasi pada titik tertentu yaitu pada titik kontak hubung singkat, sedangkan pada kondisi beban arus berlebih titik kerusakan terlokalisasi pada satu atau beberapa lokasi tertentu dari sepanjang kawat penghantar. Karakteristik makro dari manik-manik busur (bead) yang terbentuk pada kondisi hubung singkat listrik dan beban arus berlebih adalah mengandung banyak rongga (voids) serta terlihat jelas batas transisi antara bahan yang mencair/ resolidifikasi dengan bahan yang tidak mencairnya. Sedangkan karakteristik manik-manik berupa gumpalan yang terbentuk pada perlakuan pemanasan dengan nyala api langsung, tidak menunjukkan transisi yang tajam antara bahan yang mencair/ resolidifikasi. Struktur mikro manik-manik dari material kawat tembaga penghantar listrik NYM 3x1,5 pada kondisi perlakuan: hubung singkat, beban arus berlebih, dan pemanasan dengan nyala api langsung, adalah struktur dendritik dari fasa alfa (α). ......The purpose of this study was to evaluate the characteristics of the bead formed due to short circuit, overload and direct flame treatment on NYM 3x1.5 copper power cable. Handling of short circuit and overload is carried out at a current load of 800% of the current carrying capacity (144 Amperes) and direct flame treatment is carried out at a temperature of 960 degrees Celsius. The bead specimens formed from each treatment were examined and tested in the laboratory: chemical composition examination, visual inspection, macro and micro structural examination, hardness testing, and SEM-EDS examination. The difference in the characteristics of the arc bead that is formed under short circuit conditions and overload is that in short circuit conditions the damage point is localized at a certain point, namely at the short circuit contact point, while under overload conditions the point damage is localized at one or several specific locations along the wire. The macro characteristic of arc beads formed under short-circuit and overload conditions is that they contain many cavities and a clear transition boundary between the melted/ re-solidified material and the non-melted material. While the characteristics of the granules in the form of globular formed in the direct flame treatment, do not show sharp transitions between melting/ re-solidified materials. The micro structure of NYM 3x1.5 beads of electrically conducting copper wire material under the treatment conditions: short circuit, overload and direct ignition, is an alpha (α) phase dendritic structure. 
Depok: Fakultas Teknik Universitas Indonesia, 2023
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Herninta Fadhilah Novrianti
Abstrak :
Penelitian ini memanfaatkan daur ulang Printed Circuit Board (PCB) untuk digunakan sebagai partikel nano pada fabrikasi nanofluida untuk aplikasi media quench. Pemisahan fraksi logam dan non logam pada PCB melalui perlakuan asam dengan stirring PCB pada larutan HCl 1 M selama 22 jam dan daur ulang PCB dilakukan melalui proses pirolisis dengan variabel durasi; 15, 30, dan 45 menit pada suhu 500oC untuk melihat pengaruh material partikel dan durasi pirolisis terhadap karakteristik konduktivitas termal dan viskositas nanofluida. Reduksi ukuran partikel dilakukan dengan proses wet milling selama 15 jam menggunakan alat Planetary Ball Mill (PBM) kecepatan 500 rpm. Fabrikasi nanofluida dilakukan dengan penambahan 1% partikel PCB ke dalam 100 ml air. Dilakukan variasi penambahan 3% Sodium Dodecylbenzene Sulfonate (SDBS) sebagai surfaktan untuk melihat pengaruhnya terhadap stabilitas nanofluida. Karakteristik partikel dan nanofluida dilakukan menggunakan pengujian EDS, SEM, PSA, konduktivitas termal, viskositas, dan potensial zeta. Persentase volume terbesar dari partikel berukuran nano yang didapatkan adalah sebesar 44,8% oleh jenis partikel non logam hasil pirolisis 15 menit. Konduktivitas termal tertinggi didapatkan dari sampel nanofluida dengan partikel non logam hasil pirolisis 15 menit, yaitu 0,642 W/m.K. Durasi pirolisis yang digunakan tidak berpengaruh signifikan terhadap viskositas karena konsentrasi partikel yang terlalu rendah (1%). Stabilitas nanofluida meningkat dengan penambahan 3% SDBS hingga mencapai -26,7 mV. ......This research used Printed Circuit Board (PCB) as nanoparticles in nanofluid fabrication. Separation of metal and nonmetal fractions on PCB through acid treatment by stirring the PCB in 1 M HCl solution and PCB recycling was carried out through a pyrolysis process with variable duration; 15, 30, and 45 minutes at 500oC to see the effect of particle material and pyrolysis duration on the characteristics of thermal conductivity and viscosity of nanofluids. Particle size reduction was carried out by wet milling process for 15 hours using a Planetary Ball Mill (PBM) with a speed of 500 rpm. Nanofluid fabrication was carried out by adding 1% PCB particles to 100 ml of water. The addition of 3% Sodium Dodecylbenzene Sulfonate (SDBS) as a surfactant was done to observe the stability of nanofluids. The characteristics of particles and nanofluids were carried out using EDS, SEM, PSA, thermal conductivity, viscosity, and zeta potential tests. The largest volume percentage of nano-sized particles obtained was 44.8% by non-metallic particles with pyrolysis duration of 15 minutes. The highest thermal conductivity was obtained from nanofluid samples with non-metallic particles resulting from 15 minutes of pyrolysis, which was 0.642 W/m.K. The pyrolysis duration used had no significant effect on the viscosity because the particle concentration was too low (1%). The stability of the nanofluid increased to -26.7 mV with the addition of 3% SDBS.
Depok: Fakultas Teknik Universitas Indonesia, 2022
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Doni Abdul Mukti
Abstrak :
Proteksi adalah pengaman pada sistem tenaga listrik yang terpasang pada sistem distribusi tenaga listrik, trafo tenaga, transmisi tenaga listrik dan generator listrik dipergunakan untuk mengamankan sistem tenaga listrik dari gangguan listrik atau beban lebih dengan cara memisahkan bagian sistem tenaga listrik yang terganggu dengan sistem tenaga listrik yang tidak terganggu sehingga sistem kelistrikan yang tidak terganggu dapat terus bekerja. Sistem proteksi pada gardu T75B, T149 dan MG61 terjadi kegagalan kerja dimana saat ada gangguan hubung singkat disisi konsumen, mengakibatkan PMT (Pemutus Tenaga) Penyulang trip. Hal ini mengakibatkan pemadaman meluas yang tidak diharapkan. Untuk mengetahui penyebab kegagalan sistem proteksi dilakukan beberapa pengujian dan analisis menggunakan metode Root Cause Analysis yaitu pengujian koordinasi relay proteksi, pengujian performa alat proteksi, analisis konstruksi sistem proteksi, dan Perhitungan pemilihan alat proteksi. Pada gardu T75B, penyebab kegagalan sistem proteksi terdapat pada kesalahan pemilihan Transformator Arus yang jenuh saat dialiri arus gangguan melebihi 3.375 A. Pada gardu T149, penyebab kegagalan sistem proteksi terdapat pada pengaturan timing trip antara gardu dstribusi dan penyulang koasi memiliki kesamaan pada kurva Definite Time yaitu 0,2 sekon. Pada gardu MG61, penyebab kegagalan sistem proteksi terdapat pada kesalahan pemilihan Transformator Arus yang jenuh saat dialiri arus gangguan melebihi 1.250 A. Diharapkan dengan hasil pengujian tersebut dapat menjadi acuan untuk perbaikan sistem proteksi sehingga kegagalan serupa tidak terulang kembali. ......Protection is a safety in the electric power system installed in the electric power distribution system, power transformer, electric power transmission, and generator used to secure the power system electricity from electrical disturbances or overloads by separating the disturbed parts of the electric power system from the undisturbed electrical power system so that the undisturbed electrical system can continue to work. The protection system at the Distribution Substation of T75B, T149 and MG61 has a work failure where when there is a short circuit on the consumer side, it causes the PMT (Power Breaker) for the Feeder does not trip. This resulted in an unexpected widespread blackout. To find out the cause of the failure of the protection system, several tests and analyzes were carried out using Root Cause Analysis methods, namely protection relay coordination testing, protection equipment performance testing, protection system construction analysis, and calculation of selection of protection equipment. At the T75B substation, the cause of the protection system failure is the Current Transformer design error which is saturated when the fault current exceeds 3.375 A. At the T149 substation, the cause of the protection system failure is the timing trip setting between the distribution substation and the feeder which has the same Definite Time curve as 0,2 sec. At the MG61 substation, the cause of the failure of the protection system is the Current Transformer selection which is saturated when the fault current exceeds 1.250 A.It is hoped that the test results can be used as a reference for improvement protection system so that similar failures do not recur.
Depok: Fakultas Teknik Universitas Indonesia, 2021
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Etty Eryani
Abstrak :
Gesloten Circuit adalah sebuah puisi naratif berkisah tentang penyair, khayalan penyair dan opini penyair tentang dirinya dan puisi. Bundel ini metnbentuk cerita berbingkai dan disajikan secara segar dan humoris. Tujuan skripsi ini adalah menelusuri ciri-ciri sajak Konrij. Melalui Gesloten Circuit pembaca bisa melihat kekhasan gaya bertutur Komrij. Skripsi ii berisi analisis tema dan unsur-unsur pendukung tema: pilihan kata, bunyi, tipografi, sisipan.
Depok: Fakultas Ilmu Pengetahuan dan Budaya Universitas Indonesia, 1993
S15953
UI - Skripsi Membership  Universitas Indonesia Library
cover
Daniel Meino Soedira
Abstrak :
Papan elektronik atau PCB (Printed Circuit Board) merupakan bagian yang tidak terlepas dari perangkat elektronik seperti telepon genggam, televisi, komputer, lemari es dan mesin cuci. Seiring dengan perkembangan zaman, perangkat elektronik semakin mutakhir dan semakin banyak diproduksi. Manusia saat ini juga tidak bisa lepas dari telepon genggam dalam kehidupan sehari- harinya. Model atau tipe baru dari telepon genggam terus bertambah setiap tahunnya dan banyak konsumen yang selalu mengganti telepon genggam mereka dengan yang baru. Ditambah dengan peralatan rumah tangga seperti mesin cuci dan lemari es yang sudah rusak, membuat banyaknya sampah elektronik yang menumpuk. Pemanfaatan kembali bahan elektronik yang sudah dibuang, akan meningkatkan nilai jual dari sampah elektronik tersebut. Adapun material berharga seperti emas, tembaga, aluminium dan timah yang terkandung dalam sampah elektronik terutama pada bagian papan elektronik atau PCB (Printed Circuit Board). Untuk mendapatkan material tersebut, diperlukan adanya pemisahan. Salah satunya adalah dengan cara dicacah dengan mesin pencacah. Papan elektronik akan dicacah sehingga diperoleh ukuran yang lebih kecil dari papan tersebut. Dengan ukuran yang sudah dicacah, akan mudah diproses lebih lanjut dan lebih spesifik untuk perolehan material berharga yang diinginkan. Mesin pencacah mampu mencacah dengan rata- rata ukuran cacahan 8,124 mm dengan sieve ukuran 8 mm, 7,121 mm dengan sieve ukuran 6 mm dan 5,244 mm dengan sieve ukuran 4 mm. Adapun kapasitas pencacahan sebesar 24 kg/jam untuk sieve ukuran 8 mm, 17 kg/jam untuk sieve ukuran 6 mm, dan 10 kg/jam untuk sieve ukuran 4 mm
Electronic board or PCB (Printed Circuit Board) is a part that can not be separated from electronic devices such as mobile phones, televisions, computers, refrigerators and washing machines. Along with the times, electronic devices are increasingly sophisticated and more and more produced. Humans today also cannot be separated from cell phones in their daily lives. New models or types of mobile phones continue to grow each year and many consumers are always replacing their mobile phones with new ones. Coupled with household appliances such as washing machines and refrigerators that have been damaged, making the amount of electronic waste that has accumulated. Re-use of electronic materials that have been thrown away, will increase the selling value of the electronic waste. The valuable materials such as gold, copper, aluminum and tin contained in electronic waste, especially on the electronic board or PCB (Printed Circuit Board). To get this material, separation is needed. One of them is by chopping with a chopper machine. Electronic boards will be chopped so that a smaller size is obtained from the board. With the size that has been chopped, it will be easily processed further and more specifically for the acquisition of the desired valuable material. The chopper is capable of chopping with an average size of 8,124 mm with an 8 mm sieve, 7,121 mm with a 6 mm sieve and 5,244 mm with a 4 mm sieve. The enumeration capacity of 24 kg / hour for sieve size of 8 mm, 17 kg / hour for sieve size of 6 mm, and 10 kg / hour for sieve size of 4 mm.
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aji Wibisono
Abstrak :
Dalam limbah elektronik, bagian yang paling banyak dan tinggi kandungan logam berharga terdapat pada bagian printed circuit board PCB , antara lain emas dan tembaga. Penelitian ini bertujuan untuk melihat pengaruh penambahan zat H2O2 dan MnO2 sebagai oksidator terhadap nilai recovery logam emas dan tembaga menggunakan media asam klorida pada printed circuit board. Ukuran PCB direduksi menjadi 1,0 ndash; 2,0 cm2. Pelindian dilakukan menggunakan aquaregia sebagai larutan kontrol untuk mengetahui kadar awal logam emas dan tembaga, kemudian analisa AAS. Setelah itu dilakukan pelindian dengan menggunakan media asam klorida dengan variasi penambahan oksidator H2O2 serta MnO2 sebanyak 3 dan 5 dan kemudian dilakukan analisa AAS. Sehingga akan didapatkan nilai recovery dari logam emas dan tembaga dari penelitian ini. Nilai recovery logam emas dan tembaga paling tinggi ada pada larutan HCl 0,5 M dengan penambahan oksidator H2O2 sebanyak 5 , nilai recovery yang didapat yaitu 59 untuk logam emas dan tembaga.
In electronic waste, part containing most and high content of valuable metals is located in printed circuit board PCB part, such as gold and cooper. This research aim to observe the effect of adding H2O2 and MnO2 as oxidizing agent on the value of gold and cooper recovery using chloric acid leaching media on printed circuit board. The size of PCB is reduced to 1.0 ndash 2.0 cm2. The leaching is done using aquaregia as lixiviant control in order to determine the gold and cooper content, and later be analyzed by AAS. Afterwards, leaching is done using chloric acid media with the variation addition of H2O2 and MnO2 as oxidizing agent with the amount of 3 and 5, and later be analyzed by AAS. The result of the research is the value of gold and cooper recovery. The highest gold and cooper metals recovery contained on HCl 0.5 M lixiviant with the addition of H2O2 5, with the value of recovery 59 for gold and cooper metals.
Depok: Fakultas Teknik Universitas Indonesia, 2017
S67429
UI - Skripsi Membership  Universitas Indonesia Library
<<   2 3 4 5 6 7 8 9 10 11   >>