Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 129 dokumen yang sesuai dengan query
cover
Nur Mumtahinah
Abstrak :
Biosensor merupakan alat deteksi yang terdiri dari elemen sensor biologi dan sebuah transducer elektronik yang mengubah sinyal biokimia ke dalam suatu respons elektrik yang dapat diukur. Penelitian bertujuan menguji potensi biomassa khamir Rhodotorula mucilaginosa (Jörgensen) F.C. Harrison UICC Y-235 sebagai elemen biologi pada biosensor logam berat Cu2+, dengan metode konduktometrik. Penelitian dilakukan di Laboratorium Mikrobiologi dan Genetika, Departemen Biologi dan Laboratorium Smart System Technology, Departemen Fisika FMIPA UI, Depok selama 10 bulan (Juni 2006 sampai Maret 2007). Pengukuran kemampuan biosensor didasarkan pada besarnya perubahan nilai konduktivitas listrik (resistansi (R) dan impedansi (Z)) di udara dan di larutan Cu2+ oleh transducer. Biosensor dirancang dengan menentukan elemen sensor biologi dan bentuk transducer yang tepat. Hasil penelitian menunjukkan pengukuran Cu2+ terbaik pada biosensor dengan campuran biomassa dan pasta karbon (2:1) sebagai elemen sensor biologi, dan Printed Circuit Board (PCB) dengan dua garis elektode Cu-Ag sebagai transducer. Pengujian biosensor menunjukkan waktu respons yang cepat (4--54 detik) dan sensitivitas deteksi yang baik pada kisaran konsentrasi 100--2.000 ppm. Biomassa khamir menunjukkan kemampuan mengikat logam Cu yang lebih signifikan (99,7--99,9%) dibandingkan pasta karbon (0,05--0,27%). Penelitian membuktikan bahwa strain R. mucilaginosa UICC Y-235 berpotensi sebagai elemen biologi pada biosensor logam berat Cu2+.
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2007
S31436
UI - Skripsi Membership  Universitas Indonesia Library
cover
Fahmi Firdaus Angkasa
Abstrak :
Pada tahun 2025 pemerintah menargetkan peran energi baru terbarukan (EBT) minimal 23% dari bauran energi nasional ketenagalistrikan. Salah satu jenis EBT adalah panas bumi yang menjadi salah satu potensi yang besar. Berdasakan data Kementiran ESDM, potensi energi panas bumi sebesar 28.579 MWe yang terdiri dari sumber daya sebesar 11.073 MWe dan cadangan sebesar 17.506 MWe. Selain itu berdasarkan RUPTL 2019-2028, komposisi bauran energi listrik regional Sumatera akan mencapai 38,5% bersumber EBT atau mencapai total 2647,1 MW yang terdiri dari air sebesar 20,1%, panas bumi sebesar 19,5%, dan sumber EBT lainnya sebesar 1,9%. Pada tahun 2019-2023, terdapat Pembangkit Listrik Tenaga Panas Bumi (PLTP) yang direncanakan akan memasuki sistem interkoneksi Sumatera Utara pada dengan total kapasitas 240 MW. Oleh karena itu, studi interkoneksi dibutuhkan untuk mengetahui efek dari pembangkit terhadap jaringan interkoneksi dan kesesuaian dengan standar yang ada. Studi interkoneksi yang dilakukan terdiri dari studi aliran daya, studi stabilitas sistem tenaga listrik, dan studi hubung singkat menggunakan perangkat lunak DIgSILENT Power Factory 2019 SP 4. Hasil dari studi aliran daya menunjukan level tegangan pada pembangkit dan dua Gardu Induk (GI) terdekat sesuai dengan aturan yang berlaku pada Aturan Jaringan Sistem Tenaga Listrik Sumatera 2007 2.1.b yang menyebutkan standar tegangan pada jaringan interkoneksi 150 kV harus selalu diantara 135 kV dan 165 kV (±10% tegangan nominal). Selain itu, stabilitas sistem tenaga listrik dilihat dari parameter tegangan, frekuensi dan sudut rotor. Jaringan interkoneksi tetap stabil ketika ada gangguan di salah satu generator pembangkit, gangguan di satu atau dua saluran antara pembangkit dan GI terdekat, dan pelepasan beban di salah satu GI. Ketidakstabilan terjadi ketika dua GI terdekat terisolasi dengan jaringan interkoneksi Sumatera yang menghasilkan pemadaman total. Sementara itu, penambahan kapasitas pembangkit pada sistem interkoneksi 150 kV Sumatera Utara menyebabkan nilai arus hubung singkat di GI meningkat. Seluruh nilai arus hubung singkat masih memenuhi standar IEEE Std C37.06-2009. ......In 2025 the government is targeting the renewable energy at least 23% of the national electricity energy mix. One type of renewable energy is geothermal which has a great potential. Based on the Ministry of Energy and Mineral Resources Republic of Indonesia data, the potential for geothermal energy is 28,579 MWe consisting of resources 11,073 MWe and reserves 17,506 MWe. Further based on 2019-2028 RUPTL, the composition of Sumatra's regional electric energy mix will reach 38.5% from renewable sources or reach a total of 2647.1 MW consisting of water 20.1%r, geothermal 19.5%, and other renewable sources by 1.9%. In 2019-2023, there is a Geothermal Power Plant which is planned to enter the North Sumatra interconnection system with a total capacity of 240 MW. Therefore, an interconnection study is needed to determine the effect of the new power plant on the interconnection grid and compliance with the standards. Interconnection studies carried out consist of power flow, stability, and short circuit study using the DIgSILENT Power Factory 2019 SP 4 software. The results of the power flow study show that the voltage level at the power plant and the two closest substations is in accordance with the Grid code Electricity System Power System 2007 2.1.b which states the voltage standard on the 150 kV interconnection grid must always be between 135 kV and 165 kV (± 10% nominal voltage). In addition, the stability of the electric power system can be seen from the voltage, frequency and rotor angle parameters. The grid remains stable when there is a disturbance in one of the power plant generators, disturbance in one or two cables between power plant and the nearest substation, and the release of load in one of the substations. Instability occurs when it is isolated with the Sumatra interconnection grid which results in total blackouts. Meanwhile, the addition of generating capacity through PLTP in the 150 kV North Sumatra interconnection system causes the value of short circuit current in substations increase. All short circuit current still meets IEEE Std C37.06-2009 standard.
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Daffa Prasetia Putra
Abstrak :
Kompleksitas Perkembangan pesat ekonomi dan teknologi telah meningkatkan jumlah limbah elektronik (e-waste), termasuk Printed Circuit Board (PCB) yang cukup sulit didaur ulang. PCB mengandung zat berbahaya dan logam berharga, sehingga pembuangan yang tidak tepat dapat mencemari lingkungan. Penelitian ini menganalisis evolusi ukuran partikel PCB menggunakan metode wet milling dengan variasi durasi milling 1, 2, dan 3 jam. Karakterisasi utama dilakukan menggunakan Particle Size Analysis (PSA). Hasil menunjukkan ukuran partikel sebelum milling adalah 1140 nm, setelah milling 1 jam menjadi 953.9 nm, 2 jam menjadi 1498 nm, dan 3 jam menjadi 939.7 nm. Faktor yang mempengaruhi hasil meliputi aglomerasi akibat cold welding, pembentukan slurry pada vial karena suhu berlebih, dan mekanisme ductile-to-ductile. Penelitian ini dilakukan untuk mengetahui potensi penggunaan wet milling dalam proses daur ulang PCB dan faktor-faktor yang mempengaruhi evolusi ukuran partikel selama proses tersebut. ......The complexity of rapid economic and technological development has increased the amount of electronic waste (e-waste), including Printed Circuit Boards (PCBs) which are quite difficult to recycle. PCBs contain hazardous substances and precious metals, so improper disposal can pollute the environment. This study analyzes the evolution of PCB particle size using the wet milling method with milling duration variations of 1, 2, and 3 hours. The main characterization was performed using Particle Size Analysis (PSA). Results show that the particle size before milling was 1140 nm, after 1 hour of milling it became 953.9 nm, after 2 hours 1498 nm, and after 3 hours 939.7 nm. Factors influencing the results include agglomeration due to cold welding, slurry formation in the vial due to excessive temperature, and ductile-to-ductile mechanisms. This research was conducted to determine the potential use of wet milling in the PCB recycling process and the factors that influence the evolution of particle size during the process.
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Arrazy Akmal
Abstrak :
Dengan kemajuan teknologi, maka pemakaian produk elektronik akan terus meningkat. Sehingga peluang untuk mengolah limbah elektronik sangatlah besar untuk era yang sekarang sedang berjalan. Salah satu limbah elektronik yang menjadi target proses pengolahan limbah adalah, Printed Circuit Board. Limbah PCB direduksi ukurannya menjadi sekitar 1,0 cm x 1,0 cm, dan kemudian limbah PCB yang telah dilakukan reduksi ukuran kemudian di leaching dengan menggunakan larutan asam klorida, asam klorida ditambahkan hydrogen peroxide, serta larutan aqua regia, masing ndash; masing dengan konsentrasi 4M dan 6M. Hasil dari proses leaching tersebut kemudian dilakukan pengujian secara visual dan dengan Optical Microscope untuk mengetahui transformasi fisik setelah proses leaching dan juga pengujian dengan Atomic Absorption Spectrophotometery untuk mendapatkan nilai recovery logam emas dan tembaga. Hasil dari proses leaching menunjukkan recovery logam emas dan tembaga dapat mencapai sebesar 64.50 dan 90.24.
With the advancement of technology, the usage of electronic products will continue to increase. And because of this, it is an immense opportunity to recycle electronic wastes. One of the known types of electronic waste to be targeted for the recycling process of electronic wastes is, the Printed Circuit Board. In which, PCB waste is reduced in size about 1.0 cm x 1.0 cm, and after it is reduced in size, it is then leached by using hydrochloric acid solution, hydrochloric acid mixed with hydrogen peroxide, and aqua regia solution, each with concentration of 4M and 6M. The result of the leaching process is then tested visually and by using Optical Microscope to understand the physical transformation after the leaching process. And then it is tested by using the Atomic Absorption Spectrophotometery in order to get the recovery value of gold and copper metals. The results of the leaching process shows that recovery of gold and copper metals could reach up to 64.50 and 90.24.
Depok: Fakultas Teknik Universitas Indonesia, 2017
S68392
UI - Skripsi Membership  Universitas Indonesia Library
cover
Kianda Dhipatya Syahindra
Abstrak :
Grid PT Perusahaan Listrik Negara (PLN) Persero belum dapat menyuplai seluruh daerah di Indonesia. Contoh provinsi dengan rasio elektrifikasi yang masih rendah adalah Kalimantan Tengah. PT Adaro Indonesia dengan fasilitas Terminal Khusus Batu Bara di Kelanis adalah salah satu konsumen industri di provinsi tersebut yang belum memeroleh suplai listrik dari grid PLN. Oleh sebab itu, perusahaan menggunakan Pembangkit Listrik Tenaga Diesel sebagai sumber listrik utamanya serta memanfaatkan grid terisolasi untuk penyaluran ke beban. Dalam rangka menurunkan konsumsi diesel dan juga biaya, perusahaan telah menginstalasi Pembangkit Listrik Tenaga Surya (PLTS) 130 kWp dan berencana untuk menambah kapasitas. Untuk itu, penelitian ini menyimulasikan penambahan PLTS berkapasitas 467 kWp dan selanjutnya 1700 kWp pada grid terisolasi di Kelanis. Simulasi dilakukan dengan perangkat lunak DIgSILENT PowerFactory. Hasil simulasi aliran daya menunjukkan bahwa kondisi tegangan bus serta pembebanan pembangkitan dan penghantar masih dalam kondisi aman. Simulasi hubung singkat menunjukkan kesesuaian antara besarnya arus gangguan dengan kapasitas pemutusan bus, sedangkan simulasi kestabilan menunjukkan kondisi aman pada semua skenario setelah dilakukannya tindakan antisipasi dan penanggulangan. Penambahan kapasitas PLTS pun mampu menurunkan nilai Levelized Cost of Energy menjadi 0,166 USD/kWh, penghematan bahan bakar sebanyak 759.345,384 liter/tahun, penghematan biaya sebesar 394.859,6 USD/tahun, dan pengurangan emisi gas CO2 senilai 2.019,86 ton/tahun ......The grid of PT Perusahaan Listrik Negara (PLN) Persero has not been able to supply all regions of Indonesia. An example of a province with low electrification ratio is Central Kalimantan. PT Adaro Indonesia with its Coal Terminal facility in Kelanis is an industrial customer in the province who has not received electricity supply from the PLN grid. Therefore, the company uses diesel generators as its main electricity source and utilizes an isolated grid for distribution to loads. In order to reduce diesel consumption as well as costs, the company has installed a 130 kWp Solar PV system and plans to increase its capacity. For this reason, this study simulates the addition of Solar PV systems with a capacity of 467 kWp and 1700 kWp to the isolated grid at Kelanis. Simulations were carried out with the DIgSILENT PowerFactory software. The load flow simulation results show that bus voltage conditions as well as the generator and line loading percentages are still within the permitted interval. Short circuit simulations show correct breaking capacity values referring to the fault current magnitudes, while stability simulations result in safe conditions for all scenarios after required actions are done. The increase of Solar PV capacity was also able to reduce the Levelized Cost of Energy value to from 0,171 USD /kWh to 0,166 USD/kWh, save 759.345,384 liters/year of fuel, reduce 394.859,6 USD/year of costs, and reduce 2.019,86 tonnes/year of CO2
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Gilbert Cesar
Abstrak :
Perkembangan industri pengolahan limbah elektronik di Indonesia masih sangat minim dan masih menggunakan metode konvensional yang masih tergolong berbahaya bagi lingkungan dan manusia. Seiring dengan berjalannya waktu, dilakukan berbagai penelitian untuk mengatasi masalah tersebut, salah satunya adalah penggunaan larutan asam klorida. Pada penelitian kali ini digunakan sampel Printed Circuit Board untuk melihat perilaku elektrokimia dari logam Cu pada larutan asam klorida dengan konsentrasi 0.1 M, 0.2 M dan 0.5 M dengan menggunakan metode pengujian pelindian, pengujian polarisasi linear dan pengujian Electrochemical Impedance Spectroscopy EIS. Hasil penelitan EIS menunjukan bahwa pengujian PCB-Cu pada larutan asam klorida 0.5 M memiliki diameter kurva semicircle paling kecil diantara larutan asam klorida yang lain. Berdasarkan hasil fitting kurva Nyquist dengan model sirkuit ekuivalen, didapatkan bahwa hasil nilai Rctpaling kecil diantara konsentrasi lain dan lama waktu celup dimiliki oleh larutan asam klorida 0.5 M dengan waktu celup 60 menit yaitu sebesar 0.33 x 103?. Kemudian hasil pengujian polarisasi menunjukan densitas arus dan laju korosi terbesar diantara konsentrasi lain dimiliki oleh larutan asam klorida 0.5 M yaitu sebesar 1.302 A/cm2dan 0.074 mm/year. Hasil ini menunjukan bahwa peningkatan nilai konsentrasi dari larutan asam klorida akan membuat nilai transfer muatan Rct menjadi semakin berkurang, namun meningkatkan densitas arus dan laju korosi dimana hal tersebut menandakan bahwa laju pelindian dari logam Cu pada Printed Circuit Board PCB semakin meningkat seiring dengan peningkatan konsentrasi dari larutan asam klorida.
The development of electronic waste processing industry in Indonesia is still very minimum and still uses conventional methods that are still classified as dangerous for the environment and human. Over time, various studies were conducted to solve the problem, one of which was the use of hydrochloric acid solution. In this research, experiments are performed using Printed Circuit Board as the sample,to see the electrochemical behaviour of Copper in chloride solution with concentration of 0.1 M, 0.2 M and 0.5 M using leaching, linear polarization and Electrochemical Impedance Spectroscopy EIS method. The result of EIS test shows that the experiment of PCB Cu in 0.5 M chloride solution has the smallest diameter of semicircle curve among other chloride solution.Based on fitting results of Nyquist curve with equivalent circuit model, shows that the smallest Rct value among other concentration and immersion time held by 0.5 M Chloride Solution with 60 minutes of immersion time which is 0.33 x 103, then based on linear polarization test shows that the biggest current density and corrosion rate value among other chloride solution held by 0.5 M Chloride Solution which are 1.302 A cm2and 0.074 mm year. These results shows that with the increase of concentration of chloride solution will decrease the value of charge transfer resistance Rct , but on the other hand will increase the current density and corrosion rate, and can be concluded that recovery rate of Copper from Printed Circuit Board PCB increases along with the increase of concentration of Chloride Soluton.
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Purba, Bastian Bonifacius
Abstrak :
ABSTRAK Penelitian ini bertujuan untuk mengetahui studi elektrokimia dari logam tembaga pada Printed Circuit Board PCB pada larutan asam sulfat H2SO4 dengan konsentrasi 0,1 M, 0,2 M dan 0,5 M dengan menggunakan metode pengujian pelindian yang disertai dengan pengujian polarisasi linear korosi dan pengujian Electrochemical Impedance Spectroscopy EIS . Pengujian polarisasi linear korosi dilakukan untuk mengetahui laju korosi dari sampel yang digunakan. Hasil dari pengujian linear korosi menunjukkan bahwa larutan asam sulfat dengan konsentrasi 0,5 M memiliki nilai icorr paling tinggi yang berarti laju korosinya juga paling cepat sebesar 3,76 mm/tahun. Selanjutnya dilakukan pengujian Electrochemical Impedance Spectroscopy EIS yang bertujuan untuk mengetahui ketahanan transfer muatan Rct atau ketahanan sampel terhadap korosi. Hasil yang didapatkan pengujian dengan menggunakan larutan asam sulfat 0,5 M memiliki ketahanan paling buruk yang memiliki nilai Rct sebesar 179 ? dan berarti laju pelindian paling tinggi. Pengujian ini menggunakan variabel waktu celup untuk mengetahui perilaku sampel terhadap variabel waktu. Lembaran tembaga dilakukan pengujian yang sama untuk variabel pembanding pada pengujian ini.
ABSTRACT The purpose of this research is to know electrochemical studies of copper metal on Printed Circuit Board PCB in sulfuric acid solution H2SO4 with concentrations of 0.1 M, 0.2 M and 0.5 M using leaching testing method accompanied by linear corrosion polarization testing and Electrochemical Impedance Spectroscopy EIS testing. Linear linear polarization testing was performed to determine the corrosion rate of the samples used. The result of corrosion linear test showed that the solution of sulfuric acid with a concentration of 0.5 M has the highest icorr value which means the fastest corrosion rate is 3.7669 mm year. Furthermore, the testing of Electrochemical Impedance Spectroscopy EIS which aims to determine the resistance of charge transfer Rct or sample resistance to corrosion. The results obtained by testing using 0.5 sulfuric acid solution have the worst resistance that has a Rct value of 179 and means the highest leaching rate. This test uses immerse time variable to know the behavior of the sample against time variable. The copper sheets were carried out the same tests for the comparison variables in this test.
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Prakala Djoen Turangga
Abstrak :
Penggunaan perangkat elektronik di dunia sangat tinggi terutama di Indonesia. Perangkat elektronik yang sudah tidak digunakan menghasilkan limbah elektronik e-waste yang memiliki logam-logam berharga di dalamnya terutama pada komponen Printed Circuit Board PCB yang dapat didaur ulang. Penelitian ini akan membahas tentang studi elektrokimia pada proses pelindian tembaga dengan menggunakan asam nitrat HNO3 pada konsentrasi 0,1M, 0,2M, dan 0,5M. Sampel yang berupa PCB akan dilakukan pengujian polarisasi dan Electrochemical Impedance Spectroscopy EIS dengan waktu Celup 0 menit, 30 menit, dan 60 menit untuk mengetahui proses pelindian yang terjadi dalam larutan asam nitrat. Laju pelindian pada PCB maupun pada tembaga semakin meningkat dengan bertambahnya konsentrasi asam nitrat, namun seiring bertambahnya waktu celup, penggunaan konsentrasi asam nitrat 0,5 M pada PCB menghasilkan produk korosi dari unsur logam lain yang menghambat proses pelindian. Penelitian ini ditujukan untuk mencari larutan yang efektif dalam pengolahan limbah elektronik.
Electronic device usage is very high around the world especially in Indonesia. These electronic devices resulting high amount of electronic waste e waste with lot of useful metals in it especially on Printed Circuit Board PCB components. This research will discuss about electrochemical study on copper leaching process by using nitric acid HNO3 at concentrations of 0.1M, 0.2M, and 0.5M. Samples in the form of PCBs will be tested for polarization and Electrochemical Impedance Spectroscopy EIS with immersion time 0 minute, 30 minutes, and 60 minutes to determine the leaching process occurring in the nitric acid solution and to study about the effectiveness of the leaching by studying the leaching mechanism and rate of leachability by comparing it with the same test of pure copper 99.9 leaching in solution of nitric acid at the same amount of concentration. Result from this research shown that rate of leaching with higher concentration of nitric acid makes the rate of leaching increasing too, but the usement of 0.5 M nitric acid resulting products of corrosion from another metal elements stick to the surface which inhibit the leaching process. This research have a goal to determine the most effective leachings solution to recycle e waste.
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Tarigan, Ruben Timotius
Abstrak :
Nikel dan kobalt adalah salah satu logam yang sangat penting seiring dengan kemajuan teknologi yang sangat pesat. Nikel dan kobalt merupakan logam yang sangat berkaitan erat dengan baja nirkarat atau stainless steel dan juga baterai generasi terbaru yaitu baterai berbasis Ni/Co. Hal ini mendorong penelitian dibidang ekstraksi kedua logam tersebut untuk dilakukan lebih dalam lagi. Pada penelitian ini akan dilakukan studi elektrokimia dari bijih nikel laterit dengan metode reduction roasting yang akan diikuti dengan pelindian pada larutan asam sulfat (hidrometalurgi). Metode ini memiliki beberapa keuntungan yang lebih baik daripada proses ekstraksi konvensional dari bijih nikel yaitu dengan pirometalurgi karena konsumsi energinya yang lebih kecil dan biaya operasi yang lebih murah. Sebelum dilakukan studi elektrokimia sampel terlebih dahulu melalui proses reduksi (sampai T = 1000°C dengan waktu penahanan selama 1 jam). Tujuan dari penelitian ini adalah untuk mengetahui bagaimana perilaku dari bijih nikel laterit saat dilakukan pelindian pada larutan asam klorida (HCl) dengan konsentrasi yang divariasikan (1 M, 2 M, 4 M dan 6 M) pada temperatur ruang (±25°C) dengan metode studi elektrokimia, yaitu Open Circuit Potential, Electrochemical Impedance Spectroscopy, dan Linear Polarization. Nilai OCP mengalami kenaikan seiring dengan kenaikan konsentrasi larutan. Dari grafik LP dapat dilihat bahwa terbentuk lapisan pasif pada setiap konsentrasi. Hasil pengujian EIS menunjukkan kecenderungan penipisan lapisan pasif seiring dengan meningkatnya konsentrasi yang dapat dilihat dari nilai CPE yang meningkat. Dari studi elektrokimia yang telah dilakukan menujukkan bahwa dengan adanya peningkatan konsentrasi larutan terjadi kenaikan laju pelarutan. ......Nickel and cobalt are one of the most important metals as technology advances very rapidly. Nickel and cobalt are metals that are strongly associated with stainless steel and the latest generation batteries which is Ni/Co-based batteries. This encourages research in the field of extraction of these two metals to be done even deeper. In this research, electrochemical studies of laterite nickel ore will be carried out by roasting reduction method which will be followed by leaching in sulfuric acid solution (hydrometallurgical). This method has several advantages over conventional extraction processes from nickel ore, such as pyrometallurgy because of its lower energy consumption and lower operating costs. Before the electrochemical studies are carried out, the sample first goes through the reduction process stage (up to T = 1000°C with holding time = 1 hour). The purpose of this study was to determine how the behavior of laterite nickel ore when leach in hydrochloric acid (HCl) solution with varied concentrations (1 M, 2 M, 4 M and 6 M) at room temperature (± 25°C) with electrochemical study method (Open Circuit Potential, Electrochemical Impedance Spectroscopy and Linear Polarization). OCP values increase with increasing concentration of solution. From the LP chart it can be seen that a passive layer is formed at each concentration. The EIS test results show the tendency of thinning of the passive layer along with increasing concentration which can be seen from the increasing CPE value. From the electrochemical studies that have been carried out shows that the increase in solution concentration causes an increase in the dissolution rate.
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Mohammad Rendra Sura Aditama
Abstrak :
Penelitian ini bertujuan untuk mengetahui studi elektrokimia dan mengamati respon dari sample yang berupa lembaran tembaga, printed circuit board (PCB) bekas dan PCB kosong pada larutan asam sulfat (H2SO4) berkonsentrasi 0,1 M dan 1 M menggunakan metode pengujian pelindian yang disertai dengan pengujian polarisasi linear dan pengujian electrochemical impedance spectroscopy (EIS). Pengujian polarisasi linear bertujuan untuk mengetahui laju korosi dari sampel. Hasil dari pengujian polarisasi linear menunjukkan bahwa larutan asam sulfat dengan konsentrasi 1 M memiliki nilai icorr lebih tinggi pada semua sampel yang berujung pada laju korosi lebih tinggi, yakni 196 x 10-2 mm/tahun untuk PCB bekas, 592,8 x 10-2 mm/tahun untuk lembaran tembaga dan 79,7 x 10-5 mm/tahun untuk PCB kosong. Selanjutnya, dilakukan pengujian EIS yang bertujuan untuk mengetahui ketahanan transfer muatan sampel (Rct). Hasil yang didapatkan menunjukkan pengujian pada PCB bekas menggunakan asam sulfat 0,1 M memiliki Rct paling besar senilai 413 x 103 Ω yang merupakan keadaan dimana sampel memiliki kecenderungan sangat kecil untuk terkorosi. Pengujian ini menggunakan variabel berupa konsentrasi dan sampel yang merupakan multilayer PCB bekas dan double-layer PCB kosong dengan variabel pembanding berupa tembaga. ......This study aims to acknowledge electrochemical studies and observe the response of samples in form of copper sheets, used printed circuit board (PCB) and blank PCBs in sulfuric acid (H2SO4) concentration of 0.1 M and 1 M using leaching method accompanied by linear polarization and electrochemical impedance spectroscopy (EIS). Linear polarization testing aims to determine the corrosion rate of the sample. The results of linear polarization testing showed that a solution of sulfuric acid with a concentration of 1 M had higher icorr values ​​among all samples which resulted in a higher corrosion rate, which is 196 x 10-2 mm/year for used PCBs, 592.8 x 10-2 mm/year for copper sheets and 79.7 x 10-5 mm/year for blank PCBs. Furthermore, an EIS experiment was conducted to determine the resistance of transfer of sample charges (Rct). The results obtained show that experiment on used PCBs using 0.1 M sulfuric acid has the largest Rct worth 413 x 103 Ω which indicates a situation where the sample has a very small tendency to corrode. This test uses a variable in concentration and sample which is a used multilayer PCB and double-layer plain PCB with a comparison variable in the form of copper.
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   5 6 7 8 9 10 11 12 13   >>