Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 128 dokumen yang sesuai dengan query
cover
Jelita Ninda Qorina
"ABSTRAK
Microbial Desalination Cell (MDC) adalah salah satu metode dalam wastewater treatment dimana MDC juga dapat mendesalinasi air laut dan memproduksi listrik karena bakteri yang dimanfaatkan pada sistem MDC merupakan bakteri exoelectrogenic yang merupakan bakteri penghasil listrik. Stacked Microbial Desalination Cell (SMDC) merupakan pengembangan MDC dimana SMDC menggunakan banyak pasangan dari ion Exchange Membranes (IEMs) dimana IEMs diletakkan diantara Anion Exchange Membrane (AEM) dan Cation Exchange Membrane (CEM). Hal ini ditujukan untuk meningkatkan efisiensi transfer elektron. SMDC juga dapat mengembalikan lebih banyak energi dibandingkan jenis MDC lain sehingga biaya yang digunakan lebih efektif. Namun, kekurangan SMDC yaitu terbatasnya proton pada elektroda yang menyebabkan kecilnya produksi listrik SMDC dimana memengaruhi juga SMDC sebagai sistem pengolahan limbah. Oleh karena itu, dilakukan penambahan resin penukar ion yang dapat menstabilkan hambatan ohm dimana hambatan semakin meningkat seiring dengan pengurangan konsentrasi garam dan konduktifitas. Studi ini mengembangkan sistem SMDC dengan penambahan resin penukar ion pada ruang garam dimana substrat yang digunakan yaitu model limbah oli. Variasi yang dilakukan yaitu perbandingan resin penukar ion berturut turut sebesar 1:1; 1;1,7; dan tanpa penambahan resin penukar ion. Hasil yang didapat, resin dengan perbandingan 1:1,7 dapat mengurangi konsentrasi COD sebesar 50,729% dan power density sebesar 7,035 x 10-4 W/m3, serta perubahan pH sebesar 0,19. Hasil ini lebih baik dibanding dengan variasi perbandingan 1:1 dan tanpa penambahan resin.

ABSTRACT
Microbial Desalination Cell (MDC) is one of the methods in wastewater treatment where MDC can also desalinate seawater and produce electricity because bacteria that used in the MDC system are exoelectrogenic bacteria which are electricity-producing bacteria. Stacked Microbial Desalination Cell (SMDC) is an MDC development where SMDC uses many pairs of ion Exchange Membranes (IEMs) where IEMs are placed between the Anion Exchange Membrane (AEM) and the Cation Exchange Membrane (CEM). This is intended to increase the efficiency of electron transfer. SMDC can also return more energy than other types of MDC so that the cost is more effectively. However, the lack of SMDC is the limited proton of the electrode which causes the small production of SMDC electricity which also affects the SMDC as a waste treatment system. Therefore, the addition of ion exchange resins can stabilize the ohm resistance where the resistance increases with the reduction in salt concentration and conductivity. This study develops an SMDC system by adding an ion exchange resin to the salt ruang where the substrate used is waste engine oil model. Variations made are the ratio of successive ion exchange resins by 1: 1; 1; 1,7; and without the addition of ion exchange resins. The results obtained, resin with a ratio of 1: 1.7 can reduce the COD concentration by 50,729% and power density by 7.035 x 10-4 W / m3, and the change in pH by 0.19. This result is better than the 1: 1 ratio variation and without the addition of resin."
2020
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Daffa Ramadhan Aridis
"ABSTRAK
Proses penggilingan padi akan menghasilkan produk samping, salah satunya yaitu bekatul yang memiliki potensi yang sangat besar baik dari segi ekonomi maupun kesehatan tubuh jika diolah lebih lanjut, namun hingga saat ini pemanfaatan bekatul masih sangat terbatas. Bekatul mengandung kadar minyak yang cukup tinggi yaitu sekitar 10-23% yang terdiri atas 80% asam lemak tak jenuh dan 20% asam lemak jenuh. Asam lemak tak jenuh umumnya diperoleh dari minyak ikan, namun minyak ikan mempunyai harga yang mahal dan berbau amis. Kandungan asam lemak tak jenuh pada bekatul dapat diperkaya dengan memanfaatkan kapang Aspergillus terreus, karena kapang tersebut dapat menghasilkan asam lemak tak jenuh lebih tinggi dibanding jenis kapang Aspergillus lainnya. Penelitian ini mengkaji pengaruh variasi pH medium terhadap peningkatan kadar asam lemak tak jenuh pada minyak bekatul hasil fermentasi menggunakan kapang Aspergillus terreus. Metode fermentasi yang digunakan adalah metode fermentasi padat dengan metode ekstraksi Bligh-Dyer termodifikasi dan instrumen Gas Chromatography/Mass Spectrometry (GC-MS) digunakan untuk mengetahui komposisi dan kandungan dari asam lemak tak jenuh dalam minyak bekatul. Hasil penelitian menunjukkan bahwa pH medium optimum untuk peningkatan kadar asam lemak tak jenuh dalam minyak bekatul dengan menggunakan Aspergillus terreus, yaitu pada pH 5 dengan kadar asam lemak tak jenuh semula 74,835% menjadi 76,719%.

ABSTRACT
The rice milling process will produce side products, one of them is rice bran which has enormous potential both in terms of economy and health if it is further processed, but until now the use of rice bran is still very limited. Rice bran contains a fairly high oil content, which is around 10-23% consisting of 80% unsaturated fatty acids and 20% saturated fatty acids. Unsaturated fatty acids are generally obtained from fish oil, but fish oil has a high price and smells fishy. The content of unsaturated fatty acids in rice bran can be enriched by using Aspergillus terreus, because these molds can produce unsaturated fatty acid higher than other types of Aspergillus. This study examines the effect of pH of the medium variations on increasing unsaturated fatty acid content in fermented rice bran oil using Aspergillus terreus. The fermentation method used is solid-state fermentation with modified Bligh-Dyer extraction method and Gas Chromatography/Mass Spectrometry (GC-MS) instrument is used to determine the composition and content of unsaturated fatty acids in bran oil. The result showed that the optimum pH of the medium for increasing the unsaturated fatty acid contents in rice bran oil using Aspergillus terreus, which is at pH 5 with the initial unsaturated fatty acid content of 74.835% to 76.719%."
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Novrina Ariij Aisyti
"Salah satu perkembangan menarik dalam pengobatan kanker adalah target terapi kanker, yaitu pemberian obat yang ditargetkan secara molekuler untuk menginhibisi protein onkogenik tirosin kinase. Tirosin kinase adalah enzim kinase yang berperan dalam proses seluler seperti pertumbuhan, diferensiasi, migrasi, dan apoptosis sebuah sel. Mutasi atau ekspresi berlebih dari tirosin kinase dapat mengakibatkan perubahan fungsi seluler tirosin kinase yang memicu pembentukan sel tumor dan kanker, sehingga inhibisi dari protein tersebut dapat memperlambat proliferasi dan angiogenesis dari sel kanker. Pada penelitian ini, permodelan secara in silico digunakan untuk mengetahui aktivitas inhibisi senyawa propolis yang berasal dari lebah tak bersengat Tetragonula biroi aff. Indonesia pada target protein tirosin kinase penyebab non-small cell lung cancer (NSCLC), kanker payudara, dan leukemia myeloid. 18 senyawa uji propolis yang memiliki potensi antikanker diujikan sebagai inhibitor untuk menghambat aktivitas protein Anaplastic Lymphoma Kinase (ALK), Human Epidermal Growth Factor Receptor 2 (HER2), dan Brutons Tyrosine Kinase (BTK) penyebab NSCLC, kanker payudara, dan leukemia myeloid secara berturut-turut. Penambatan dikomputasikan menggunakan AutoDock Vina®, dengan LigPlot+ dan PyMOL untuk memvisualisasikan interaksi molekuler antara kompleks inhibitor-protein yang dihasilkan. Hasil menunjukkan bahwa kurarinon adalah inhibitor yang paling kuat terhadap ALK dengan skor -8,8 kkal/mol, yang berinteraksi dengan Met1199 sebagai residu utama untuk menghambat ALK. Sementara itu macarangin memiliki skor penambatan tertinggi untuk target HER2 dengan nilai sebesar -11,3 kkal/mol, dan Derrubone sebagai inhibitor paling kuat untuk BTK dengan skor -9,4 kkal/mol. Maka dari itu, studi ini menunjukkan bahwa kurarinon berpotensi untuk menjadi inhibitor ALK, dengan macarangin berpotensi sebagai inhibitor HER2, dan derrubone berpotensi untuk menjadi inhibitor BTK sehingga ketiga senyawa tersebut dapat diteliti dan dievaluasi lebih lanjut untuk studi in-vitro dan in-vivo sebagai novel inhibitor ALK, HER2, dan BTK.

 


One of the interesting developments in cancer treatment is the use of cancer targeted therapy, a molecular targeted drugs that are given to inhibit the oncogenic protein of tyrosine kinases. The tyrosine kinases is a group of kinase enzyme that plays a role in cellular processes such as cell growth, differentiation, migration, and apoptosis. Mutation or overexpression of tyrosine kinases can result in disruption of tyrosine kinase cellular function which triggers the formation of tumor and cancerous cells, where the inhibition of these proteins can slow down the proliferation and angiogenesis of cancer cells. In this study, in-silico modeling was used to determine the inhibitory activity of propolis compounds derived from Indonesian Tetragonula biroi aff. targeting tyrosine kinase protein that causes non-small cell lung cancer (NSCLC), breast cancer, and myeloid leukemia. 18 propolis compounds that have anticancer potential are tested as inhibitors to block the activity of Anaplastic Lymphoma Kinase (ALK), Human Epidermal Growth Factor Receptor 2 (HER2), and Bruton's Tyrosine Kinase (BTK) protein that causes NSCLC, breast cancer, and myeloid leukemia respectively. Docking was computed using AutoDock Vina®, with LigPlot+ and PyMOL to visualize molecular interactions between the resulting inhibitor-protein complex. The result show that kurarinone is the most potent inhibitor towards ALK with a score -8,8 kcal/mol, interacting with Met1199 as a key residues for inhibiting ALK. Meanwhile macarangin has the highest docking score for HER2 target resulting in -11,3 kcal/mol, and derrubone as the most potent inhibitor for BTK with a score of -9,4 kcal/mol. This study suggest that kurarinone has the potential as ALK inhibitor, with macarangin has the potential to inhibit HER2, and derrubone has the potential as BTK inhibitor so that the three compounds can be further investigated and evaluated for in-vitro and in-vivo studies as novel ALK, HER2, and BTK inhibitors.

"

Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Chiara Aurelia
"Peningkatan kadar kolesterol dalam darah merupakan salah satu faktor utama dalam berbagai penyakit kardiovaskuler. Oleh karena itu, dibutuhkan metode praktis yang dapat mendeteksi kadar kolesterol secara berkala. Pengembangan terbaru alat pendeteksi kadar kolesterol saat ini cenderung mengarah pada biosensor menggunakan enzim kolesterol oksidase (CHOx). Untuk mengoptimalkan kinerja enzim dan memperoleh biokompatibilitas dan selektivitasnya yang tinggi, diperlukan teknik imobilisasi dengan material support. Selulosa merupakan salah satu biopolimer di alam dengan ketersediaan paling berlimpah dan serbaguna, serta memiliki karakteristik yang sensitif, akurat, dan biayanya yang murah. Aplikasi selulosa untuk imobilisasi enzim dikombinasikan dengan magnetit, yaitu logam oksida yang memiliki sifat paramagnetik tinggi. Tujuan dari penelitian ini adalah untuk mempelajari aplikasi dari penggabungan material magnetit dan selulosa sebagai support imobilisasi enzim CHOx. Penelitian ini menggunakan enzim CHOx Streptomyces sp. komersil. Parameter yang diuji dalam penelitian diantaranya ialah konsentrasi enzim optimum yang digunakan saat proses imobilisasi, serta aktivitas relatif dan residual dari enzim ChOx–baik setelah pengulangan penggunaan maupun setelah penyimpanan dalam waktu tertentu. Enzim yang telah direaksikan diuji dengan alat spektrofotometer UV-Vis. Sampel enzim terimobilisasi akan dicuci kembali menggunakan buffer untuk uji penggunaan kembali. Hasil yang diperoleh dari penelitian ini diantaranya; konsentrasi enzim CHOx (Ce) yang paling efektif digunakan untuk imobilisasi pada material magnetit-selulosa ialah 2 mg/10 mL, retensi aktivitas enzim terimobilisasi material dapat bertahan ~10% setelah digunakan ulang sebanyak empat kali, dan aktivitas relatif enzim terimobilisasi dapat bertahan hingga ~5% pada hari ke-10 penyimpanan–dengan tingkat stabilitas waktu simpan yang lebih baik daripada enzim bebas.

Increasing levels of cholesterol in blood is one of the main causes in many cardiovascular diseases. Therefore, a practical method of detecting cholesterol levels on a regular basis is needed. The latest development of cholesterol level detection device currently leads to biosensors using cholesterol oxidase enzyme (CHOx). To optimize enzyme performance and obtain high biocompatibility and selectivity, an immobilization technique with material support is required. Cellulose is one of the most widely available and versatile biopolymers in nature, and has characteristics that are sensitive, accurate, and low-cost. The application of cellulose for enzyme immobilization is combined with magnetite, a metal oxide that has high paramagnetic properties. The purpose of this research was to study the application of the incorporation between magnetite and cellulose materials as a support for CHOx enzyme immobilization. This study uses commercial CHOx derived from Streptomyces sp. The parameters tested in this study include the optimal enzyme concentration used during the immobilization process, as well as the relative and residual activity of the ChOx enzyme–after repeated uses and after certain period of storage. The reacted enzymes were tested with a UV-Vis spectrophotometer. The immobilized enzyme sample was washed each time after use with buffer saline for reusability assays. The results obtained from this study include; the most effective concentration of CHOx enzyme (Ce) used for immobilization on magnetite-cellulose material was 2 mg/10 mL, retention of enzyme activity of immobilized material could last ~10% after being used four times, and the relative activity of immobilized enzyme could last up to ~5% on the 10th day of storage–with a better shelf-life than the free enzyme."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Amalia Weediyanti
"Kanker merupakan penyebab kematian terbanyak urutan ketiga di Indonesia. Kanker adalah penyakit yang disebabkan oleh pertumbuhan abnormal dari sel tubuh. Salah satu dari penyebab kanker adalah adanya radikal bebas reactive oxygen species (ROS) pada tubuh. Radikal bebas merupakan senyawa yang memiliki elektron tidak berpasangan, sehingga bersifat reaktif. Radikal bebas dapat distabilkan dengan antioksidan. Fikosianin adalah salah satu zat yang memiliki aktivitas antioksidan dan dengan begitu memiliki potensi untuk mencegah kanker. Spirulina platensis adalah penghasil fikosianin yang paling dikenal. Kandungan dari fikosianin pada Spirulina dapat dioptimalkan melalui jenis dan kandungan nitrogen pada media kultivasi. Penelitian ini akan mengkaji hal tersebut dengan memvariasikan sumber nitrogen pada medium Zarrouk, yaitu NaNO3 dan NH4NO3, dan konsentrasinya untuk kultur Spirulina platensis. Kultivasi dilakukan pada fotobioreaktor 250 mL dengan aerasi 250 mL/min, pencahayaan kontinyu 2200 lux, dan suhu 27 – 30 °C, selama 165 jam periode kultivasi. Fikosianin kemudian diekstrak dengan metode sonikasi dan diuji aktivitas antioksidannya dengan metode DPPH. Profil pertumbuhan, yield fikosianin, dan aktivitas antioksidan terbaik didapat dari kultur dengan NaNO3 0,03 M sebagai sumber nitrogen. Yield fikosianin yang didapat adalah sebesar 22,996 ± 0,072 mg/g dengan nilai IC50 sebesar 1.438,681 ± 50,274 ppm.

Cancer is the third leading cause of death in Indonesia. Cancer is a disease caused by abnormal growth of body cells. One of the causes of cancer is the presence of free radicals reactive oxygen species (ROS) in the body. Free radicals are compounds that have unpaired electrons, this condition will make them reactive. Free radicals can be stabilized by antioxidants. Spirulina platensis is the best known producer of phycocyanin. The content of phycocyanin in Spirulina can be optimized through the type and concentration of the nitrogen in the cultivation medium. This study will examine this matter by varying the nitrogen sources in Zarrouk medium, namely NaNO3 and NH4NO3, and their concentrations for Spirulina platensis culture. Cultivation was carried out in a 250 mL photobioreactor with aeration of 250 mL/minute, continous lighting of 2200 lux, and temperature of 27 – 30 °C for 165 hours of cultivation. Phycocyanin then was extracted by ultrasonication method and tested for its antioxidant activity by DPPH method. The best growth profile, phycocyanin yield, and antioxidant activity were obtained from culture that used NaNO3 0.03 M as nitrogen source. The yield of phycocyanin obtained was 22,996 ± 0,072 mg/g with an IC50 value of 1.438,681 ± 50,274 ppm."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Fauzul Fadli
"VHR (Vaccinia H1-related phosphatase) adalah protein yang terlibat dalam kanker serviks. Dengan obat-obatan saat ini yang mahal dan menimbulkan efek samping, sehingga diperlukan pengobatan alternatif. Daun keji beling mengandung senyawa flavonoid yang merupakan senyawa fenolik alami yang berpotensi sebagai antikanker. Untuk mendapatkan senyawa aktif, metode ekstraksi yang digunakan adalah Aqueous two-phase system (ATPS) dan Ultrasound-assisted enzymatic extraction (UAEE), dimana keduanya merupakan kombinasi metode ekstraksi hijau dan pemurnian. Kondisi operasi optimal metode ATPS yang digunakan dalam penelitian ini adalah rasio etanol 33wt% dan ammonium sulfat 14wt% yang menghasilkan nilai recovery 98,043%, nilai K 31,179, yield kuersetin 3,504mg/g, dan konsentrasi kuersetin 44,717 mg/L. Ekstrak daun keji beling diuji dengan metode shinoda, spektrofotometri UV-Vis juga Gas Chromatography and Mass Spectrometry (GC-MS), kemudian senyawa yang teridentifikasi memiliki aktivitas antikanker yaitu kuersetin, n-hexadenoic acid dan 9-dodecenoic acid, methyl ester, (E)-. Hasil uji docking molekuler memberikan docking score terbaik untuk kuersetin yaitu -6,7, diikuti oleh asam n-heksadekanoat bernilai -5,1 dan terakhir adalah asam 9-dodekenoat, metil ester, (E) - bernilai -4,2 terhadap protein 1J4X. Kuersetin merupakan senyawa dengan potensi inhibisi terbaik terhadap VHR yang ditunjukkan dengan nilai docking score terendah.

VHR (Vaccinia H1-related phosphatase) is a protein involved in cervical cancer. With current drugs which are expensive and cause side effects, an alternative treatment is needed. Keji beling leaves contain flavonoid compounds which are natural phenolic compounds that have the potential as anticancer. To obtain active compounds, the extraction methods used are Aqueous two-phase system (ATPS) and Ultrasound-assisted enzymatic extraction (UAEE), both of which are a combination of green extraction and purification methods. Optimal operating conditions for the ATPS method used in this study were 33wt% ethanol ratio and 14wt% ammonium sulfate which resulted in 98,043% recovery value, K value 31,179, quercetin yield 3.504 mg/g, and quercetin concentration 44.717 mg/L. Keji beling leaf extract was tested by the shinoda method, UV-Vis spectrophotometry as well as Gas Chromatography and Mass Spectrometry (GC-MS), then the compounds identified as having anticancer activity were quercetin, n-hexadenoic acid and 9-dodecenoic acid, methyl ester, (E-). Molecular docking test results give the best docking score for quercetin which is -6.7, followed by n-hexadecanoic acid -5.1 and finally is 9-dodecenoic acid, methyl ester, (E) - value -4.2 to 1J4X protein. Quercetin is a compound with the best inhibition potential against VHR which is shown by the lowest docking score."
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Dhea Putriani
"Di Indonesia, data menyebutkan bahwa 93 persen anak usia dini pada rentang usia lima hingga enam tahun mengalami karies. Fluoride telah diakui sebagai bahan aktif, yang bisa digunakan dalam pencegahan karies. Aplikasi fluoride varnish yang memiliki pelepasan ion fluoride dan kalsium yang cepat, selain meningkatkan efektivitas dalam pencegahan karies tingkat tinggi juga menambah nilai kenyamanan dalam hal rasa dan aroma pada pasiennya, terutama anak-anak. Penelitian ini melakukan studi tentang formulasi dasar fluoride varnish dengan penambahan minyak perasa dan agen remineralisasi dikalsium fosfat dihidrat. Hasil formulasi akan diuji kandungan pelepasan ion fluoride dan kalsium setelah 6 jam menggunakan alat ion selektif elektroda. Variabel bebas yang diujikan yaitu perasa, konsentrasi perasa, jenis kalsium dan konsentrasi kalsium fosfat. Hasil data dianalisis dengan uji ANOVA satu arah dan Tukey post hoc dengan tingkat signifikansi α=0,05. Hasil membuktikan perbedaan variabel yang diujikan memberikan hasil yang berbeda secara signifikan terhadap pelepasan ion fluoride dan kalsium. Pelepasan ion fluoride tertinggi diperoleh dari formulasi peppermint 2,5% dan DCPD-Xylitol 1% sebesar 296,8952 mg/L. Untuk kalsium, formulasi peppermint 2,5% dan DCPD-Casein 3% yang memberikan kumulatif pelepasan ion kalsium tertinggi sebesar 113, 8667 mg/L Selain itu, kelayakan ekonomi juga dianalisis untuk dengan meninjau nilai NPV, IRR, Net B/C dan Payback Period.

In Indonesia, the data states that 93 percent of early childhood in the age range of five to six years have caries. Fluoride has been recognized as an active ingredient, which can be used in caries prevention. The application of fluoride varnish, which has a fast release of fluoride and calcium ions, in addition to increasing effectiveness in the prevention of high caries levels also adds value in terms of taste and aroma comfort in patients, especially children. This study conducted a study of a basic formulation of fluoride varnish with the addition of a flavoring oil and a remineralization agent of dicalcium phosphate dihydrate. The results of the product will be tested for the release of fluoride and calcium ions after 6 hours using a selective ion electrode. The independent variables tested were types of flavor, flavor concentration, types of calcium, and calcium phosphate concentration. The results of the data were analyzed by a one way ANOVA test and Tukey post hoc with a significance level α = 0.05. The results prove the differences in the variables tested gave significantly different effects on the release of fluoride and calcium ions. The highest fluoride ion release was obtained from a 2.5% peppermint formulation and 1% DCPD-Xylitol at 296.8952 mg/L. For calcium, 2.5% peppermint formulation and 3% DCPD Casein which provide the highest cumulative release of calcium ions reaches 113, 8667 mg/L. Also, economic viability is also analyzed to review NPV, IRR, Net B/C and Payback Period
"
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ananda Bagus Richky Digdaya Putra
"Diagnostik medis merupakan tahapan awal dalam mengidentifikasi kondisi dan penyakit seseorang. Salah satu metode diagnostik yang banyak dipakai sekarang ini adalah Polymerase Chain Reaction (PCR). Penggunaan material perangkat thermal cycler dalam reaksi PCR mempengaruhi waktu yang dibutuhkan dalam prosesnya. Dengan kemajuan teknologi mikrofluida, chip thermal cycler dengan sistem mikrofluida banyak dikembangkan untuk meningkatkan kecepatan reaksi PCR. Studi ini mensimulasikan beberapa material dan geometri yang digunakan sebagai thermal cycler reaksi PCR Studi pada penelitian ini akan menggunakan aplikasi COMSOL Multiphysics 5.3 untuk dua desain PCR, thermal cycle tipe blok (TCP desain 1) dan thermal cycle tipe mikrofluida (TCP desain 2). Hasil yang didapatkan adalah waktu jenuh untuk TCP desain 1 menggunakan material aluminium selama 29 detik untuk pemanasan dan 26 detik untuk pendinginan, tembaga selama 37 detik untuk pemanasan dan 35 detik untuk pendinginan, nikel selama 51 detik untuk pemanasan dan 53 detik untuk pendinginan, perak selama 26 detik untuk pemanasan dan pendinginan, serta PDMS selama 1480 detik untuk pemanasan dan pendinginan. Pada TCP desain 1, saat menggunakan aluminium, didapatkan waktu jenuh untuk memanaskan reagen selama 32 detik dan 35 detik untuk mendinginkan. Pada PCR TCP desain 2 (a) yang langsung menggunakan PDMS, didapatkan waktu untuk jenuh memanaskan reagen adalah 3,2 detik dan 4,3 detik untuk mendinginkan, sedangkan pada TCP desain 2 (b) didapatkan waktu untuk memanaskan reagen selama 4,3 detik dan 4,6 detik untuk mendinginkan.


Medical diagnosis is the initial stage in solving a person's condition and disease. One method that is widely used now is the Polymerase Chain Reaction (PCR). The use of thermal cycler device material in the PCR reaction affects the time required in the process. With the advancement of microfluidic technology, thermal cycler chips with microfluidic systems have been developed to increase the speed of PCR reactions. This study discusses several materials and geometries used as PCR thermal cycler reactions. COMSOL Multiphysics 5.3 application used to simulate two PCR designs, block-type thermal cycles (TCP design 1), and microfluidic type thermal cycles (TCP design 2). The results obtained are the saturation time for TCP design 1 using aluminum material for 29 seconds for heating and 26 seconds for safety, copper for 37 seconds for heating and 35 seconds for cooling, nickel for 51 seconds for heating and 53 seconds for heating, silver for 26 seconds for heating and cooling, and PDMS for 1480 seconds for heating and cooling. In TCP design 1, when aluminum was used, saturation time is obtained to heat the reagent for 32 seconds and 35 seconds to cool. In TCP PCR design 2 (a) which directly uses PDMS, obtained time to saturate the reagent heating is 3.2 seconds and 4.3 seconds to cool, whereas in TCP design 2 (b) it takes time to heat the reagent for 4.3 seconds and 4.6 seconds to cool down.

"
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Damai Kasih Lintanghati
"Bahan bakar fosil merupakan salah satu sumber energi utama dan terbesar penggunaannya di Indonesia. Kebutuhannya pun dinilai cenderung meningkat dari tahun ke tahun. Emisi dari pembakaran gas disebut dapat menimbulkan isu lingkungan. Selain dalam tahap penggunaannya, proses produksi gas juga perlu ditinjau peranan dan dampaknya terhadap lingkungan. Penelitian ini bertujuan untuk mengidentifikasi hal tersebut lewat metode Life Cycle Assesment (LCA). Penelitian ini dibatasi oleh sistem gate-to-gate yang meliputi proses dari tahap produksi saja, dan digunakan untuk menentukan dampak lingkungan dari langkah produksi atau proses. Tinjauan proses yang dinilai dampak lingkungannya terdiri atas alur produksi gas dan kondensat serta produk samping air terproduksi.Analisa LCA proses produksi akan dihitung menggunakan peranti lunak SimaPro versi 9.0.049 dan berbasis pada neraca massa yang disimulasikan pada Aspen HYSYS versi 11. Data yang menjadi input LCA dalam penelitian ini merupakan data bahan baku, produk, produk samping, pemakaian energi, serta gas buang atau emisi pembakaran. Dari hasil penilaian dampak lingkungan, didapatkan nilai beban emisi yang dihasilkan dari proses produksi gas jual adalah 409,35 kg CO2/ton produk; 0,062 kg CH4/ton produk; 0,0062 kg NOx/ton produk; dan 0,0007 kg SOx/ton produk dengan total emisi ke udara dari proses produksi gas adalah 1,929 107 UBP/ton produk. Pada alur produksi kondensat dihasilkan beban emisi sebesar 0,206 kg CO2/ton produk; 4,05 10-5 kg CH4/ton produk; 4,37 10-6 kg NOx/ton produk; dan 9,96 10-6 kg kg SOx/ton produk dengan nilai total emisi ke udara dari proses produksi kondensat adalah 6,38 102 UBP/ton produk. Sedangkan pada hasil produk selanjutnya yaitu air dihasilkan beban emisi sebesar 102,981 kg CO2/ton produk; 1,566 CH4/ton produk; 0,157 kg NOx/ton produk; dan 0,018 kg kg SOx/ton produk dengan total emisi ke udara dari proses produksi air adalah 8,3410 107 UBP/ton produk. Kontribusi beban emisi terhadap lingkungan ini dapat diminalisasi dengan beberapa upaya seperti memaksimalkan efisiensi energi dari peralatan yang beroperasi di lapangan, injeksi CO2 sequestration, pemanfaatan gas H2S menjadi bahan kimia H2SO4 dan menggalangkan gerakan green electricity.

Fossil fuels are one of the main and biggest sources of energy in Indonesia. Their needs are also considered to increase from year to year. Emissions from combustion of gas are said to cause environmental issues. In addition to the use phase, the gas production process also needs to be reviewed for its role and impact on the environment. This study aims to identify this through the Life Cycle Assessment (LCA) method. This method is a method used to estimate the environmental impact resulting from a production process starting from exploration to the final process and disposal to the environment, or commonly known as the cradle to grave approach. This study is limited by the gate-to-gate system which includes processes from the production stage only, and is used to determine the environmental impact of the production steps or processes. A review of the processes assessed for environmental impacts consists of gas and condensate production flows and produced water byproducts. Production process LCA will be calculated using SimaPro software version 9.0.049 and based on mass balance which is simulated in Aspen HYSYS version 11. The data which is input for LCA in this research is data of raw materials, products, by-products, energy consumption, and exhaust gas or combustion emissions. From the results of the environmental impact assessment, the value of the emission load generated from the sales gas production process is 409.35 kg CO2/ton product; 0.062 kg CH4/ton product; 0.0062 kg NOx/ on product; and 0.0007 kg SOx/ton product with total emissions to the air from the gas production process is 1.929×107 UBP/ton product. In the condensate production process, emissions load of 0.206 kg CO2/ton of product is produced; 4.05×10-5 kg ​​ CH4/ton product; 4.37×10-6 kg NOx/ton product; and 9.96×10-6 kg kg SOx/ton product with total emissions to the air from the condensate production process is 6.38×102 UBP/ton product. Whereas in the next product result, water is produced an emission load of 102.981 kg CO2/ton product; 1,566 CH4/ton product; 0.157 kg NOx/ton product; and 0.018 kg kg SOx/ton product with total emissions to the air from the produced water production process is 8.3410×107 UBP/ton product. The contribution of the emission load to the environment can be finalized by several efforts such as maximizing the energy efficiency of equipment operating in the field, CO2 equesterian injection, utilization of H2S gas into H2SO4 chemicals and promoting the movement of green electricity."
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Glory Lamria
"Jumlah penderita Demam Berdarah Dengue (DBD) di provinsi DKI Jakarta terus mengalami peningkatan, terlepas dari upaya pengendalian penyebaran DBD yang telah dilakukan oleh pemerintah. Contoh dari upaya pengendalian yang telah dilakukan adalah penggunaan insektisida berbasis bahan kimia malathion. Selain dapat menimbulkan resistensi dan efek samping terhadap tubuh manusia, penggunaannya dalam fogging memerlukan penambahan bahan bakar diesel sebagai pembentuk asap. Penelitian ini bermaksud untuk memformulasikan cairan yang digunakan untuk fogging di kawasan perumahan. Formulasi ini bertujuan untuk menciptakan produk cairan insektisida untuk fogging yang bebas dari pyrethroid dan petroleum sehingga lebih aman bagi pengguna. Penelitian dilakukan dengan memformulasikan ekstrak daun tembakau sebagai zat aktif insektisida dengan pelarut berupa propilen glikol dan gliserin sebagai agen pembuat asap. Variabel bebas dalam penelitian ini adalah konsentrasi zat aktif dan rasio pelarut (PG:VG). Pengujian yang akan dilakukan terhadap sampel yang telah dibuat adalah uji toksisitas LC50, dan uji stabilitas (Uji stabilitas fisik), uji organoleptik, uji karakteristik GCMS serta penghitungan Harga Pokok Penjualan (HPP) produk. Hasil uji efektivitas cairan fogging Aedes aegypti menunjukan dengan konsentrasi ekstrak tembakau selama 10 menit antara 5%-20% belum mencapai LC50, konsentrasi 30% mencapai LC 50 pada menit ke-9, konsentrasi 40% mencapai LC 50 pada menit ke-6, dan konsentrasi 50% pada menit ke-5. Pada ekstrak tembakau dengan metode ekstraksi, konsentrasi 5%-20% belum mencapai LC 50, konsentrasi 30% mencapai LC 50 pada menit ke-9. Konsentrasi 40% mencapai LC 50 pada menit ke-4 dan konsentrasi ekstrak tembakau 50% pada menit ke-3.

The number of people with Dengue Hemorrhagic Fever (DHF) in the DKI Jakarta province continues to increase, eventhough there is number of efforts to control the spread of DHF from the government. An example of this control metthod is the use of malathion chemical-based fogging. Besides this insecticide able to cause resistance and side effects to the human body, its use in fogging requires the addition of diesel fuels as forming smoke. This study intends to formulate fluids used for fogging in residential areas. This formulation aims to create liquid fogging products for fogging that are free from pyrethroid and petroleum so that it is safer for users. The research was done by formulating tobacco leaf extract as an active insecticide substance with a solvent in the form of propylene glycol and glycerin as a smoke-making agent. The independent variables in this study were the concentration of the active substance and the ratio of solvent (PG: VG). Tests that will be conducted on the samples that have been made are LC50 toxicity test, and stability test (physical stability test), organoleptic test, GCMS test. The results of the Aedes aegypti fogging fluid efficiency test with pyrolysis showed that with a concentration of 10% -20% it has not reached LC50, the concentration of 30% reached LC 50 in the 9th minute. The concentration of 40% reached LC50 in the 6th minute and the concentration of 50% reached LC50 in the 5th minute. For tobacco extract with extraction method, the concentration of 5% -20% has not reached LC 50. The concentration of 30% reaches LC50 in the 9th minute. The concentration of 40% reached LC50 in the 4th minute and the concentration of 50% in the 3rd minute."
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>