Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 4 dokumen yang sesuai dengan query
cover
Dini Aryanti
"[ABSTRAK
Limbah lumpur yang dihasilkan dari Instalasi Pengolahan Air Limbah (IPAL) Domestik dapat dimanfaatkan melalui pengomposan karena mengandung kandungan organik yang tinggi. Namun, kandungan logam berat pada limbah lumpur dapat menjadi penyebab utama timbulnya dampak negatif pada lingkungan dan kesehatan manusia. Tujuan dari penelitian ini adalah untuk menganalisis perubahan parameter fisik-kimia, konsentrasi dan spesiasi kimia logam Cu dan Pb pada dua campuran kompos sebagai penilaian kelayakan kedua kompos untuk digunakan sebagai pupu. Hasil penelitian menunjukkan bahwa parameter suhu, pH, dan rasio C/N pada kedua kompos telah memenuhi kualitas kompos sesuai SNI 19-7030-2004. Konsentrasi logam Cu pada kompos 1 dan kompos 2 berturut-turut adalah 150 mg/kg dan 237 mg/kg, sedangkan konsentrasi logam Pb sebesar 224 mg/kg dan 183 mg/kg. Besar konsentrasi kedua logam pada kedua kompos menghasilkan faktor resiko ekologi yang masuk ke dalam kategori resiko rendah (Er < 40). Selain itu, proses pengomposan pada penelitian ini telah mengurangi efek toksisitas kedua logam. Pada akhir pengomposan, fraksi logam Cu pada kedua kompos dominan pada fraksi organic bound yaitu sebesar 63,50% untuk kompos 1 dan 56,20% untuk kompos 2. Sedangkan logam Pb dominan pada fraksi residual yaitu sebesar 62,10% pada kompos 1 dan 71,50% pada kompos 2. Kedua fraksi ini merupakan fraksi stabil sehingga keberadaan logam Cu dan Pb tidak memberikan dampak negatif bagi lingkungan jika kedua kompos diaplikasikan ke tanah.

ABSTRACT
Sewage sludge generated from Waste Water Treatment Plant (WWTP) can be reused by composting because it contains a high organic content. However, the content of heavy metals in sewage sludge can be a major cause negative impacts on the environment and human health. The purpose of this study is to analyze the changes in the physical-chemical parameters, concentration and chemical speciation of Cu and Pb in two compost mixtures as an assessment of the feasibility of both composts to be used as fertilizer. The result showed that the parameters of temperature, pH, and C/N ratio in both compost met the standard quality of compost according to SNI 19-7030-2004. Concentration of Cu in compost 1 and compost 2 were 150 mg/kg and 237 mg/kg respectively, while the concentration of Pb were 224 mg/kg and 183 mg/kg respectively. The concentration of both metals in two composts resulted Ecological Risk factor (Er) that go into a low risk category (Er < 40). In addition, the composting process in this study reduced the toxicity effect of two metals. At the end of composting, fractions of Cu in two composts were dominant in organic bound fraction in amount of 63.50% for compost 1 and 56.20% for compost 2. While Pb were dominant in the residual fraction that is equal to 62.10% for compost 1 and 71.50% for compost 2. These fractions are the stable fracion so that the existence of Cu and Pb in two compost do not give negative impact to the environment if two composts will be applied to soil.;Sewage sludge generated from Waste Water Treatment Plant (WWTP) can be reused by composting because it contains a high organic content. However, the content of heavy metals in sewage sludge can be a major cause negative impacts on the environment and human health. The purpose of this study is to analyze the changes in the physical-chemical parameters, concentration and chemical speciation of Cu and Pb in two compost mixtures as an assessment of the feasibility of both composts to be used as fertilizer. The result showed that the parameters of temperature, pH, and C/N ratio in both compost met the standard quality of compost according to SNI 19-7030-2004. Concentration of Cu in compost 1 and compost 2 were 150 mg/kg and 237 mg/kg respectively, while the concentration of Pb were 224 mg/kg and 183 mg/kg respectively. The concentration of both metals in two composts resulted Ecological Risk factor (Er) that go into a low risk category (Er < 40). In addition, the composting process in this study reduced the toxicity effect of two metals. At the end of composting, fractions of Cu in two composts were dominant in organic bound fraction in amount of 63.50% for compost 1 and 56.20% for compost 2. While Pb were dominant in the residual fraction that is equal to 62.10% for compost 1 and 71.50% for compost 2. These fractions are the stable fracion so that the existence of Cu and Pb in two compost do not give negative impact to the environment if two composts will be applied to soil., Sewage sludge generated from Waste Water Treatment Plant (WWTP) can be reused by composting because it contains a high organic content. However, the content of heavy metals in sewage sludge can be a major cause negative impacts on the environment and human health. The purpose of this study is to analyze the changes in the physical-chemical parameters, concentration and chemical speciation of Cu and Pb in two compost mixtures as an assessment of the feasibility of both composts to be used as fertilizer. The result showed that the parameters of temperature, pH, and C/N ratio in both compost met the standard quality of compost according to SNI 19-7030-2004. Concentration of Cu in compost 1 and compost 2 were 150 mg/kg and 237 mg/kg respectively, while the concentration of Pb were 224 mg/kg and 183 mg/kg respectively. The concentration of both metals in two composts resulted Ecological Risk factor (Er) that go into a low risk category (Er < 40). In addition, the composting process in this study reduced the toxicity effect of two metals. At the end of composting, fractions of Cu in two composts were dominant in organic bound fraction in amount of 63.50% for compost 1 and 56.20% for compost 2. While Pb were dominant in the residual fraction that is equal to 62.10% for compost 1 and 71.50% for compost 2. These fractions are the stable fracion so that the existence of Cu and Pb in two compost do not give negative impact to the environment if two composts will be applied to soil.]"
2015
T41481
UI - Tesis Membership  Universitas Indonesia Library
cover
Eko Siswoyo
"Lumpur yang dihasilkan dari instalasi pengolahan air minum di Indonesia masih belum dimanfaatkan dengan baik dan menjadi permasalahan bagi lingkungan. Salah satu alternatif yang dapat diterapkan yaitu dengan memanfaatkan lumpur tersebut sebagai bahan baku paving block. Penelitian ini bertujuan untuk menganalisa
perbandingan limbah lumpur yang baik dari hasil uji daya serap air, uji kekuatan dan uji Toxicity Characteristic Leaching Procedure (TCLP) kemudian juga untuk mengetahui mutu paving block serta nilai tambah ekonomi dalam produksi paving block. Pada penelitian ini dibuat beberapa variasi komposisi lumpur
PDAM yaitu 0%, 10%, 30% dan 50% dari komposisi total bahan paving block. Proses pembuatan paving block pengikuti prosedur yang ada yaitu tahapan pembuatan komposisi beton yang diinginkan, melakukan pencetakan dengan mesin press, melakukan pengeringan selama 14 hari dan perendaman selama 14 hari berikutnya. Setelah melalui tahap pengerasan selama 28 hari, kemudian dilakukan pengukuran kuat tekan dan daya serap air yang mengacu pada SNI 03-1691-1996. Selain itu dilakukan juga uji TCLP untuk
mengetahui potensi limbah berbahaya yang dapat timbul dari produk paving block yang dihasilkan. Hasil dari pengujian menunjukkan bahwa komposisi limbah lumpur 10% memberikan hasil uji kuat tekan rata-rata sebesar 8,55 MPa dan daya serap air rata-rata sebesar 3,57%. Hasil uji ini dapat memenuhi uji mutu paving block kategori ā€˜Dā€™ sesuai dengan SNI-03-0691-1996. Dan pada hasil uji TCLP menunjukkan kadar logam berat yang diujikan tidak melebihi dari baku mutu yang ada."
Bandung: Kementerian Pekerjaan Umum dan Perumahan Rakyat, 2022
728 JUPKIM 17:1 (2022)
Artikel Jurnal  Universitas Indonesia Library
cover
Mohammad Anom Guritno
"ABSTRAK
Limbah lumpur di lapangan minyak bumi dikategorikan sebagai limbah B3 dan berbahaya bagi lingkungan hidup. Air terproduksi yang merupakan aliran limbah dalam produksi minyak bumi mengandung polutan non-biodegradable seperti senyawa fenolik yang memiliki toksisitas tinggi pada perairan. Lumpur memiliki potensi besar untuk diubah menjadi karbon aktif berpori yang dapat disuspensikan dengan fotokatalis TiO2 untuk digunakan dalam degradasi senyawa fenolik melalui reaksi fotokatalisis. Dengan memodifikasi ukuran pori karbon aktif dan ukuran partikel TiO2 aktifitas fotokatalisis dapat ditingkatkan. Oleh karena itu, perlu dikaji suatu metode untuk sintesis karbon aktif berpori dan suspensinya dengan fotokatalis TiO2 dalam usaha mendegradasi senyawa fenolik yang terkandung dalam air terproduksi di lapangan minyak bumi. Pada penelitian ini, lumpur dikonversi menjadi karbon aktif berpori menggunakan metode hard template dengan MCM-41 sebagai template silika mesopori, karbonasi dilakukan dalam atmosfert inert. MCM-41 disintesis dengan metode hidrotermal menggunakan TEOS dan CTAB. TiO2 Nanowire disintesis dengan metode hidrotermal dalam larutan KOH dan dikalsinasi pada suhu berbeda untuk mengetahui bentuk partikel terbaik. Aplikasi reaksi degradasi senyawa fenolik dilakukan dengan fotokatalis TiO2 Degussa P25, TiO2 Nanowirei dan Suspensi TiO2-PAC, untuk mengetahui pengaruh ukuran partikel TiO2 dan keberadaan karbon aktif dalam reaksi degradasi senyawa fenolik. Limbah lumpur, karbon aktif berpori, TiO2 nanowire, MCM-41 dan suspense katalis TiO2-PAC hasil sintesis dikarakterisasi menggunakan CS Analyzer, FTIR, EDX, SEM, BET, XRD, PSA dan TEM. Hasil karakterisasi menunjukkan karbon aktif berpori dan MCM-41 yang dihasilkan memiliki diameter pori 3.0 dan 2.2 nm (mesopori), sesuai dengan yang diharapkan. TiO2 nanowire yang dipilih adalah hasil kalsinasi pada suhu 600 oC karena memiliki kristalinitas terbaik dibanding lainnya. Aplikasi degradasi Fenol dilakukan pada rentang waktu reaksi tertentu dan dianalisis kadar Fenol, TOC dan COD menggunakan spektrofotometer UV-Vis. Hasil reaksi degradasi senyawa fenolik menunjukkan suspensi katalis TiO2-PAC menghasilkan degradasi Fenol, TOC dan COD terbesar dengan keberhasilan degradasi (% Degradasi) sebesar 64.06 %, 49.81 % dan 24.65%. Dengan ini dapat disimpulkan bahwa limbah lumpur dapat dikonversi menjadi karbon aktif berpori yang dapat berperan dalam degradasi senyawa fenolik setelah disuspensikan dengan TiO2 Nanowire.

ABSTRACT
Petroleum sludge waste categorized as toxic waste and harmful to the environment. Produced water which is the flow of waste in petroleum production, containing non-biodegradable pollutant such as phenolic compound which have high aquatic toxicity. Sludge has great potential to be converted into a porous activated carbon (PAC) which can be suspended with TiO2 photocatalyst to degrade phenolic compound through photocatalytic reaction. By modifying pore size of the activated carbon and particle size of TiO2, photocatalytic activity can be improved. Therefore, it is necessary to study for the synthesis of activated carbon and the suspension with TiO2 photocatalyst in attempt to degrade phenolic compound contained in produced water of petroleum field. In this research, sludge is converted into PAC using hard template method with MCM-41 as template of silica mesopore, carbonization is conducted in stream of inert atmosphere. MCM- 41 synthesized by hydrothermal method using TEOS and CTAB. Nanowire TiO2 synthesized by hydrothermal method in solution of KOH and calcined at different temperatures to determine the best form of particles. Applications of phenolic compound degradation reactions performed with photocatalysts of TiO2 Degussa P25, Nanowire TiO2, and suspension of TiO2-PAC, to determine the effect of particle size of TiO2 and the presence of PAC in the reaction of phenolic compound degradation. Sludge waste, PAC, Nanowire TiO2, MCM-41, and suspension of TiO2-PAC synthesized were characterized using CS Analyzer, FTIR, EDX, SEM, BET, XRD and PSA. The results shows PAC and MCM-41 produced has a pore diameter of 3,0 and 2,2 nm (mesopore) as expected. Nanowire TiO2 chosen is the result of calcinations at temperature of 600 oC, because it has the best cristallinity than others. Phenolic compound degradation performed at certain time intervals and analyzed the content of total phenol, TOC, and COD using spectrometer UV-Vis. The results shows suspension of TiO2-PAC has largest degradation of phenolic, TOC and COD with the phenolic, TOC, and COD degradation of 64,06%, 49,81%, and 24,65%, respectively. It can be concluded that petroleum sludge waste can be converted into PAC which can play a role in the degradation of phenolic compound after suspended with Nanowire TiO2.
"
Depok: Universitas Indonesia, 2015
T45333
UI - Tesis Membership  Universitas Indonesia Library
cover
Nisa Logana Miranti
"Lumpur bor berbasis air dengan aditif Barit (B) dan KCl (K) berpotensi toksik, sehingga Lemigas berupaya melakukan pencegahan berdasarkan pengujian TCLP dan LC50 - 96 jam terhadap Penaeus monodon. Kondisi uji disesuaikan pada Sumur Bangau #1 di Sesulu PSC, Selat Makassar. Dengan kombinasi Bmin, Bmax, Kmin, dan Kmax, konsentrasi Cu pada setiap formula (Bmin-Kmin: 26,17 ppm; Bmin-Kmax: 39,74 ppm; Bmax-Kmin: 21,47 ppm; Bmax-Kmax: 31,7 ppm) dan Pb pada Bmin-Kmin (9,369 ppm) melewati baku mutu lingkungan. LC50 Formula Bmin-Kmin memenuhi baku mutu lingkungan (44.058 ppm), sedangkan Formula Bmax-Kmax tidak memenuhi baku mutu lingkungan (13.269 ppm). Hal ini dipengaruhi oleh komposisi logam berat, toksisitas KCl, dan kondisi lingkungan. WBM jenis ini lebih baik digunakan pada pengeboran off-shore.

Water based mud with Barite (B) and KCl (K) as additives have toxicity potential, therefore Lemigas performed testing prevention effort based on TCLP and LC50 ā€“ 96 hours on Penaeus monodon. Testing condition environment was adapted to Sumur Bangau #1 at Sesulu PSC, Makassar Strait. Cu concentration in Bmin, Bmax, Kmin, and Kmax combinations (Bmin-Kmin: 26,17 ppm; Bmin-Kmax: 39,74 ppm; Bmax-Kmin: 21,47 ppm; Bmax-Kmax: 31,7 ppm) and Pb in Bmin-Kmin (9,369 ppm) are above the threshold. LC50 Bmin-Kmin Formula fulfill the threshold (44.058 ppm) while Bmax-Kmax Formula did not (13.269 ppm). It is influenced by heavy metals composition, KCl toxicity, and environmental condition. This type of WBM is better used in off-shore drilling operation."
Depok: Fakultas Teknik Universitas Indonesia, 2014
S57059
UI - Skripsi Membership  Universitas Indonesia Library