Hasil Pencarian  ::  Simpan CSV :: Kembali

"

Indonesia kaya akan energi panas bumi sehingga pemanfaatannya perlu ditingkatkan untuk mendukung diversifikasi energi yang ramah lingkungan. Dengan menggunakan heat pipe sebagai perangkat transfer panas dalam pemanfaatan langsung energi panas bumi untuk pengeringan diharapkan akan mengatasi beberapa kendala dalam usaha meningkatkan penggunaan energi tersebut. Tujuan dari penelitian ini adalah untuk menyelidiki kinerja termal dari penggunaan heat pipe heat exchanger (HPHE) sebagai alat transfer panas dari fluida panas bumi temperatur rendah ke udara panas untuk pengeringan. Komoditas yang dipilih untuk percobaan adalah daun teh. Simulator fluida panas bumi (air panas) menggunakan air yang dipanaskan dengan pemanas berkapasitas 9000 Watt dan dialirkan dengan pompa. Heat pipe yang digunakan memiliki panjang 700 mm dengan diameter luar 10 mm, fluida kerja dalam heat pipe menggunakan air dengan filling ratio 50%, jumlah heat pipe yang digunakan adalah 42 buah yang sebagai HPHE. Untuk menambah luas bidang perpindahan panas, di sisi kondensor HPHE dipasang fin dengan jumlah 181 pcs. Fin terbuat dari aluminium dengan ketebalan 0,105 mm dengan ukuran 76 x 345 mm. Hasil penelitian menunjukkan bahwa nilai efektifitas HPHE terbesar yaitu 79,59 % didapat ketika menggunakan temperatur air panas 60°C, dan kecepatan udara inlet 0.2 m/s. Efektifitas HPHE terkecil yaitu 66% didapat ketika menggunakan temperatur air panas 40°C, dan kecepatan udara inlet 0.6 m/s. Model matematika Page adalah model terbaik untuk merepresentasikan perilaku pelayuan daun teh PTPN VII, sehingga penggunaan HPHE pada pemanfaatan langsung energi panas bumi temperatur rendah untuk pelayuan daun teh, dapat diterima dan layak untuk digunakan.

---

Indonesia is rich in geothermal energy and needs to be improved to support environmentally friendly energy diversification. Using heat pipes as a heat transfer device in direct use of geothermal energy for drying is expected to overcome several challenges in increasing energy use. The purpose of this study was to test the thermal performance of the use of a heat pipe heat exchanger (HPHE) as a means of transferring heat from low enthalpy geothermal fluid to hot air for drying. The agricultural product that has been choosen is tea leaves. The geothermal fluid (hot water) simulator uses heated water with a capacity of 9000 Watts and is flowed by a pump. The heat pipe used has a length of 700 mm with an outer diameter of 10 mm, a hot working fluid pipe using water with a filling ratio of 50%, the number of heat pipes used is 42 pieces which are HPHE. To increase the heat replacement area, fins are installed on the side of the HPHE condenser with 181 pcs. Fin is made of aluminum with a thickness of 0.105 mm with a size of 76 x 345 mm. The results showed the greatest effectiveness of HPHE was 79.59% obtained by compilation using 60° C hot air temperature, and inlet air velocity of 0.2 m / s. The effectiveness of HPHE which was increased by 66% was obtained using a hot air temperature of 40 ° C, and an inlet air velocity of 0.6 m / s. Page`s mathematical model is the best model to represent the protection of the tea leaves of the PTPN VII variety, using HPHE in direct use of low temperature geothermal energy for tea leaves, is acceptable and useful to use.

"

"Sel surya perovskit (PSC) efisiensi tinggi biasanya didasarkan pada ETL TiO₂. Namun, sistem berbasis TiO₂ memerlukan proses di atas 450℃. Metode suhu rendah sangat penting untuk komersialisasi PSC yang fleksibel. Oleh karena itu, SnO₂ datang sebagai kandidat yang menjanjikan yang dapat menggantikan TiO₂ sebagai ETL karena SnO₂ dapat diproses menggunakan metode suhu rendah. Sintesis dilakukan dengan metode yang simple pada suhu yang relatif rendah, dan dilanjutkan dengan proses deposisi ETL dengan variasi temperatur 90℃, 120℃, 150℃, 190℃, dan 220℃. Sampel dilakukan karakterisasi menggunakan XRD, SEM, dan UV-Vis. Untuk sampel hasil sintesis didapatkan Ukuran kristal sebesar 7,82 nm dan diameter nanopartikel sebesar 0,21 μm. serta memiliki Nilai energi celah pita (Eg) sebesar 5,21 eV. Akan tetapi setelah dilakukan anil untuk proses deposisi, Nanopartikel mengalami pertumbuhan ukuran diameter. Hasilnya dengan variasi anil 90℃, 120℃, 150℃, 190℃, dan 220℃ adalah 0.21; 0.20; 0.20; 0.22 and 0.23 μm secara berturut-turut. Dan untuk hasil dari kurva absorbansi setelah dilakukan proses anil, hasilnya menunjukkan kelima sampel tidak memiliki nilai absorbansi. Terbukti dengan dilakukannya pengujian efisiensi pada kelima variasi anil, hasilnya menunjukkan kelima sampel memiliki nilai efisiensi yang sangat kecil dengan nilai PCE paling besar sebesar 0,01% pada variasi suhu 190℃. Kemudian, dilakukan uji efisiensi dengan menggunakan sampel sel surya perovskit baru dengan lapisan ETL yang tidak dianil selama proses fabrikasi. Hasil penelitian menunjukkan nilai efisiensi yang lebih besar dibandingkan sampel yang dianil, dengan nilai PCE sebesar 1,3936%.......High efficiency perovskite solar cell (PSC) usually based on a TiO₂ electron transport layer (ETL). However, TiO₂-based systems require treatment at typically above 450℃. Low temperature method is critical for flexible PSC commercialization. Hence, SnO₂ comes as promising candidate that can substitute TiO₂ as ETL because SnO₂ can be processed using low temperature method. The synthesis was carried out using a simple method at a relatively low temperature, and continued with the ETL deposition process with temperature variations of 90℃, 120℃, 150℃, 190℃, and 220℃. The samples were characterized using XRD, SEM, and UV-Vis. The synthesis produces crystallite size of 7.82 nm with nanoparticle diameter of 0.21 μm and a band gap energy (Eg) of 5.21 eV. However, after the annealing for the deposition process, the nanoparticles grew in diameter. The results with annealing variations of 90℃, 120℃, 150℃, 190℃, and 220℃ are 0.21; 0.20; 0.20; 0.22 and 0.23 μm respectively. For the results of the absorbance curve after the annealing process, the results showed that the five samples did not have any absorbance values. It is proven by testing the efficiency on the five annealing variations that the five samples have very small efficiency values with the largest PCE value of 0.01% at a temperature variation of 190℃. In addition, an efficiency test was carried out using a new sample of perovskite solar cells with the ETL layer not annealed during the fabrication process. The results show a greater efficiency value than the annealed sample, with a PCE value of 1.3936%."

"The second edition was significantly extended by including film-substrate lattice matching and buffer layer considerations in thin film HTSCs, brick-wall microstructure in the epitaxial films, electronic structure of the CuO2 layer in cuprates, s-wave and d-wave coupling in HTSCs and possible scenarios of theories of high Tc superconductivity."

"In this study, modeling of the crossing point temperature (CPT) phenomenon in the low-temperature oxidation of coal was carried out using COMSOL Multiphysics®. Low-temperature oxidation can lead to spontaneous combustion of coal stockpiles. The CPT phenomenon was modeled with the kinetics data obtained from a prior laboratory experimental study. The coupling of the heat-transfer phenomenon through conduction and convection determined the thermal evolution model. In this case, coal received the initial heat of the oven temperature increases. As the coal temperature rose, the heat generated from oxidation was released into the environment via conduction and convection. Meanwhile, oxidation products and oxygen were transferred by convection and diffusion. The effects of moisture and the humidity were not considered. The outcomes of modeling were validated through comparison with the results of experimental tests, and the modeling result agreed well with the experiment tests, with temperature deviations of about 0.9%. The effects of airflow rate, oxygen concentration, porosity, and the initial temperature on low-temperature coal oxidation were also examined."

"In this study, modeling of the crossing point temperature (CPT) phenomenon in the low-temperature oxidation of coal was carried out using COMSOL Multiphysics®. Low-temperature oxidation can lead to spontaneous combustion of coal stockpiles. The CPT phenomenon was modeled with the kinetics data obtained from a prior laboratory experimental study. The coupling of the heat-transfer phenomenon through conduction and convection determined the thermal evolution model. In this case, coal received the initial heat of the oven temperature increases. As the coal temperature rose, the heat generated from oxidation was released into the environment via conduction and convection. Meanwhile, oxidation products and oxygen were transferred by convection and diffusion. The effects of moisture and the humidity were not considered. The outcomes of modeling were validated through comparison with the results of experimental tests, and the modeling result agreed well with the experiment tests, with temperature deviations of about 0.9%. The effects of airflow rate, oxygen concentration, porosity, and the initial temperature on low-temperature coal oxidation were also examined."

"Helium Cryogenics, 2nd edition brings these advances in helium cryogenics together in an updated form. As in the original edition, the author's approach is to survey the field of cryogenics with emphasis on helium fluids. This approach is more specialized and fundamental than that contained in other cryogenics books, which treat the associated range of cryogenic fluids. As a result, the level of treatment is more advanced and assumes a certain knowledge of fundamental engineering and physics principles, including some quantum mechanics. The goal throughout the work is to bridge the gap between the physics and engineering aspects of helium fluids to provide a source for engineers and scientists to enhance their usefulness in low-temperature systems."

"ABSTRAKUntuk mendapatkan temperatur pendinginan yang rendah diperlukan perbedaan tekanan yang tinggi. Perbedaan tekanan yang sangat tinggi mengakibatkan kerja kompresor semakin berat. Hal ini mengakibatkan turunnya efisiensi dari sistem refrijerasi sehingga perlu menggunakan sistem refrijerasi cascade. Pada pengeringan beku vakum diperlukan temperatur pendingin yang rendah pada evaporator yang berfungsi sebagai cold trap. Pengeringan beku vakum memerlukan energi untuk proses pengeringan dengan sublimasi sebesar 2870kJ/kg.s, dengan memanfaatkan panas buang kondenser sebagai pemanas dapat mengurangi waktu pengeringan. Oleh karena itu, perlu dilakukan analisa perubahan temperatur dan massa aliran refrijeran pada metode ini agar dapat mengetahui efisiensi sistem dan mengurangi energi yang dikonsumsi selama proses pengeringan berlangsung.

---

ABSTRACTFor reach of low refrigeration temperature is needed high difference pressure. High difference pressure cause increase compressor work. It is reduce efficiency of refrigeration system so need to use cascade refrigeration system. In freeze vacuum drying, is needed low refrigeration temperatur on evaporator which in function as cold trap. Freeze vacuum drying need energy for drying process by sublimation is 2870kJ/kg.s, by using heat loss condenser as heater can reduce drying time. Because of that, it is need to analyze of temperature change and flow rate refrijerant in this method to find out system efficiency and decrease energy consumption when drying process."

"Banyak aplikasi dan proses-proses di industri yang membutuhkan temperatur pendinginan sangat rendah, bahkan bidang biomedis membutuhkan cold storage yang mampu mendinginkan hingga temperatur -80°C. Penggunaan sistem refrigerasi siklus tunggal pada aplikasi temperatur sangat rendah menjadi tidak ekonomis karena tinggi nya rasio tekanan dan juga menghasilkan efek pendinginan yang tidak efektif karena rendah nya tekanan evaporasi, sehingga digunakan sistem refrigerasi cascade. Penggunaan refrigeran alamiah, seperti campuran karbon dioksida dan hidrokarbon merupakan alternatif dari penggunaan refrigeran yang mengandung bahan perusak lapisan ozon dan pemanasan global. Pada penelitian ini, dilakukan analisis termodinamika untuk menentukan komposisi campuran karbon dioksida dan hidrokarbon yang optimum. Selanjutnya, dilakukan optimisasi secara termoekonomi untuk menentukan kondisi operasi yang optimum dari sistem refrigerasi cascade, dimana peningkatan efisiensi exergy merupakan sasaran optimisasi secara termodinamika, sedangkan meminimumkan pengeluaran biaya tahunan merupakan sasaran optimisasi secara ekonomi.......There are many industrial applications and processes in which ultra-low temperature is necessary, even the biomedical preservation that needs cold storage providing temperature about -80°C. The use of single cycle refrigeration system for ultra-low temperature application is economically unacceptable caused by the high pressure ratio and results the ineffective evaporating effect as the low evaporating pressure, hence the cascade refrigeration system is applied. Natural refrigerants, such as carbon dioxide and hydrocarbon will be the alternative solutions of the used of ozon depleting and global warming effect refrigerants. In this research, thermodynamic analysis is applied to decide the optimum composition of the mixtures between carbon dioxide and hydrocarbon. Furthermore, thermoeconomic optimization results the optimum operating conditions of the cascade refrigeration system where the increasing of exergetic efficiency is the thermodynamic objective, while the minimization of the annual cost is the economic objective."