Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 23 dokumen yang sesuai dengan query
cover
Raisa Mulkiya
"Penelitian telah dilakukan untuk mengetahui pengaruh konsentrasi koloid pelindung Polivinil Alkohol (PVA) terhadap kekuatan daya rekat polimer emulsi Polivinil Asetat (PVAc). Sintesis polimerisasi emulsi dilakukan dengan teknik semi-kontinyu dengan komponen polimerisasi terdiri dari air, larutan PVA terhirolisis sebagian medium viscosity, dan surfaktan SDS. Sementara monomer Vinil Asetat (VAM) dan inisiator APS diberikan secara kontinyu selama proses sintesis berlangsung dengan temperature reaksi 70°C, kecepatan agitasi 300 rpm, dan waktu reaksi 5 jam dengan variasi konsentrasi larutan koloid pelindung PVA 2 wt%, 5 wt% dan 10 wt%. Kekuatan rekat polimer PVAc dilakukan dengan uji kuat geser terhadap kayu triplek mengikuti standar ASTM D905-03 dan diperoleh nilai shear strength PVAc meningkat seiring bertambahnya konsentrasi PVA sebesar 96, 225, 277, dan 421 kiloPascal. Parameter lain hasil akhir polimer juga dievaluasi dalam penelitian ini, meliputi temperatur reaksi, kandungan padatan, viskositas, nilai pH, dan densitas. Uji gugus fungsi pembentukan PVAc telah dilakukan dengan Spektrometer FTIR dan diketahui adanya gugus carbonyl C=O stretching & C=C stretching, dan gugus hydroxy O-H stretching. Ukuran partikel diuji dengan Dynamic Light Scattering PSA dan diperoleh ukuran 216 nm untuk PVAc tanpa koloid pelindung, sedangkan pada PVAc dengan koloid pelindung PVA berkisar antara 35-68,5 nm.

Research has been conducted to determine the effect of the concentration of protective colloid Polyvinyl Alcohol (PVA) on the adhesive strength of Polyvinyl Acetate (PVAc) emulsion polymer. The synthesis of emulsion polymerization was carried out using a semi-continuous technique with polymerization components consisting of water, partially hydrolyzed PVA solution with medium viscosity, SDS surfactant. Meanwhile, Vinyl Acetate (VAM) monomer and APS initiator were administered continuously during the synthesis process with a reaction temperature of 70°C, agitation speed of 300 rpm, and a reaction time of 5 hours with variations in the concentration of the protective colloid PVA solution 2, 5 and 10% by weight. The adhesive strength of the PVAc polymer was carried out by a shear strength test against plywood following the ASTM D905-03 standard and the value of the shear strength of PVAc increased with the increase in PVA concentration of 96, 225, 277, and 421 kiloPascal. Other parameters of the final polymer yield were also investigated in this study, including reaction temperature, solids content, viscosity, pH value, and density. Function group test for PVAc formation has been carried out with an FTIR Spectrometer and it is known that there are carbonyl groups C=O stretching & C=C stretching, and hydroxy groups O-H stretching. The particle size was tested with Dynamic Light Scattering PSA and obtained a size of 216 nm for PVAc without a protective colloid, while for PVAc with a PVA protective colloid it ranged from 35-68.5 nm."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ade Amroni
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2010
S30698
UI - Skripsi Open  Universitas Indonesia Library
cover
Prestika Gema Sari
"Telah dilakukan sintesis dan karakterisasi polimerisasi oksidasi kimia dari monomer pirol menggunakan oksidan amonium persulfat (APS) dalam media pelarut air, melalui teknik polimerisasi emulsi metode batch selama 4 jam dengan kecepatan agitasi 900 rpm dalam temperatur ruang. Surfaktan yang digunakan diantaranya, surfaktan anionik: Sodium dedocyl sulfate (SDS) dan surfaktan nonionik: Nonylphenol Ethoxylate (NP.EO) dengan 10 mol EO. Senyawa PPy dalam penelitian ini berbentuk padatan (serbuk) berwarna hitam. Terbentuknya PPy dapat diindentifikasi berdasarkan hasil spektra FTIR terlihat munculnya serapan puncak polimer konduktif PPy dengan intensitas yang kuat pada bilangan gelombang 3001 cm-1, 1503 cm-1, 1428 cm-1, 1175 cm-1 dan 1087 cm-1.
Berdasarkan profil perubahan temperatur dan perubahan warna selama proses polimerisasi terlihat polimerisasi emulsi relatif lebih lama kecepatan reaksinya dibandingkan dengan polimerisasi sedimentasi. Nilai pH sistem reaksi polimerisasi dengan surfaktan lebih tinggi (penambahan larutan SDS pH sistem 3.3) dibandingkan polimerisasi tanpa surfakan (1.8). Nilai konduktifitas (σ) PPy dengan surfaktan lebih tinggi (mencapai 186 kali) dibandingkan tanpa surfaktan. Polimerisasi emulsi menggunakan surfaktan anionik, SDS sangat efektif meningkatkan nilai konduktivitas PPy.

A conductive Polypyrrole (PPy) has been successfully synthesized and characterized. The PPy was prepared through oxidative chemical polymerization using ammonium persulfate (APS) as an oxidizing agent in aqueous media. Anionic and non-ionic emulsifiers, sodium dodecyl sulfate (SDS), nonylphenol (NP) ethoxylate (EO) with 10 mole EO were respectively used during polymerization to increase the electrical conductivity. In this research is produced PPy which is formed as black powder. The FTIR spectrum of PPy indicates a change in the absorbance peaks of pyrrole monomer, emergence of strong absorbtion peaks specially at 3001 cm-1, 1503 cm-1, 1428 cm-1, 1175 cm-1 and 1087 cm-1 which is indicating the conductive polymer polypyrrole is formed.
Based on color changing and temperature changing during the polimerization process, the reaction rate of emulsion polymerization is shown relatively slower than sedimentation polymerization. The pH value of SDS added solution was 3.3 higher than that of SDS free solution (1.8). The final characteristic of PPy was carry out by measuring the electrical conductivity (σ) value. It is concluded that the presence of surfactant in a polymerization reaction increased the electrical conductivity of PPy (reached 186 times higher) compared with that obtained of emulsifier free solution. Anionic surfactant, SDS is more effective to enhance the electrical conductivity value of PPy.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
T54427
UI - Tesis Membership  Universitas Indonesia Library
cover
Slamet Aribowo
"ABSTRAK
Telah dilakukan sintesis polianilin melalui polimerisasi oksidatif dengan menggunakan oksidator ammonium persulfate APS dengan metode kontinyu. Proses polimerisasi dilakukan dalam media asam kuat, HCl 1,5 M dibandingkan dengan media netral dengan variasi suhu lingkungan 20 oC, 30 oC dan 50 oC. Temperatur proses polimerisasi, pH larutan dan ukuran partikel dari polimer yang terbentuk setiap 5 menit hingga 60 menit pertama, dalam kurun waktu 8 jam. Nilai pH hasil pengukuran menunjukkan bahwa selama pembentukan PANI tidak banyak berubah, suhu larutan selama proses relatif sama. Pertumbuhan ukuran partikel selama proses polimerisasi dalam menunjukkan adanya tahapan inisiasi, propagasi dan terminasi baik dalam media netral dan asam kuat. Dalam media netral, pertumbuhan ukuran partikel berjalan relatif lambat, dan didominasi oleh pembentukan oligomer anilin oligoanilin yang berantai pendek. Ukuran partikel rata-rata sebesar 29 ndash; 39 m diperoleh dari polimerisasi dalam kedua media. Kedua media juga menunjukkan semakin rendah temperature media semakin besar ukuran partikel yang dihasilkan. Efek doping dengan p-TSA terhadap PANI-EB dilakukan sebagai konfirmasi untuk menunjukkan penerapan dari polianilin terdoping. Diketahui bahwa semakin tinggi suhu maka konduktivitas semakin naik. Hal ini sebagai bukti polianilin terdoping bersifat sebagai semikonduktor. Semakin besar ukuran partikel dan semakin tinggi konsentrasi doping akan meningkatkan konduktivitas dan menurunkan energi gap dari PANI terdoping p-TSA yang berakibat pada penurunan serapan terhadap gelombang mikro.

ABSTRACT
The synthesis of polyaniline was carried out by the oxidative polymerization method using ammonium persulfate APS by continuous method, in strong acid medium 1.5 M HCl and neutral medium with ambient temperature variation at 20 C, 30 C and 50 C. Measuring of the process temperature, the pH of the process solution and the particle size formation every 5 minutes to the first 60 minutes, and every hour until process has finished for 8 hours. The pH value of the measurements shows that during the formation of PANI does not change much, the temperature of the solution during the process is relatively the same. The growth of particle size during the polymerization process in indicating the presence of initiation, propagation and termination stages both in neutral and strong acid medium. In neutral media, growth of particle size formation runs relatively slowly, and it was dominated by the formation of short chain aniline oligomers oligoanilines . The average particle size of 29 39 m was obtained from polymerization in both media. Both media also show the lower the media temperature the larger the particle size have formed. The doping effect with p TSA on PANI EB was performed as a confirmation to demonstrate the application of a doped polyaniline. It is known that the higher the temperature the conductivity increases. This is a proof of polyaniline doped has behavior as semiconductor. The larger the particle size and the higher the doping concentration will increase the conductivity and decrease the gap energy of the p TSA doped PANI that decreased of microwave absorbing properties."
2018
T49057
UI - Tesis Membership  Universitas Indonesia Library
cover
Ageng Bimantoro
"ABSTRAK
Telah disintesis material polimer konduktif Polianilin (PANi) dengan menggunakan
metode polimerisasi oksidatif Anilin secara kimiawi (chemical) kemudian dilakukan
pemberian doping asam protonik yang bervariasi berupa asam kuat HCl, HClO4, dan
H2SO4. Sampel-sampel ini kemudian dikarakterisasi dengan menggunakan
spektrofotometer FTIR, Conductivity Meter, PSA (Particle Size Analyzer), dan VNA
(Vector Network Analyzer) untuk mengetahui gugus fungsi, nilai konduktivitas listrik,
ukuran partikel, dan daya serap gelombang mikro dengan rentang frekuensi tertentu
(rentang 8-12 GHz) yang terdapat pada material tersebut. Hasil karakterisasi
berdasarkan penelitian menunjukkan bahwa Polianilin (PANi) yang telah terdoping
asam protonik (terprotonasi) atau telah menjadi polimer konduktif memiliki
karakteristik puncak pita serapan IR pada bilangan gelombang antara 1141 cm-1 ?
1177 cm-1. Ukuran partikel masing-masing bentuk Polianilin hasil penelitian telah
menjadi nanopartikel dengan rentang ukuran partikel masing-masing bentuk material
ini mulai dari 4-9 nm. Polianilin yang memiliki konduktivitas listrik tertinggi yaitu
Polianilin dengan doping asam protonik HClO4 (PANi(HClO4)) sebesar 3,6 mS/cm
dan memiliki serapan gelombang mikro terendah yaitu -6,98 dB pada frekuensi 11,34
GHz. Nilai permitivitas terendah dimiliki oleh PANi(HClO4) akan tetapi dengan nilai
permitivitas yang rendah (dielectric constant negatif dan dielectric loss minimum)
dan konduktivitas listrik yang tinggi, membuat serapan gelombang mikro komposit
dengan PANi tersebut sebagai matriks akan meningkatkan jumlah serapan gelombang
mikro dan meminimalisir gelombang mikro yang ditransmisikan. Serapan gelombang
mikro material komposit tertinggi dimiliki oleh komposit dengan campuran PANi
rekayasa (PANi-ES) sebagai matriks dan Barrium Hexaferrite (BHF) yang telah
disonikasi selama 5 jam sebagai filler dengan perbandingan komposisi % berat PANi
rekayasa dan BHF 30 : 70. Material komposit tersebut adalah PANi(HClO4)/5BHF
yang memiliki serapan gelombang mikro tertinggi yaitu -38,3 dB pada frekuensi
12,28 GHz.

ABSTRACT
Polyaniline (PANi) conducting polymers have been synthesized using chemical
oxidative polymerization method on Aniline then carried granting varying protonic
acid doping form strong acid HCl, HClO4, and H2SO4. These samples were then
characterized using FTIR spectrophotometer, Conductivity Meter, PSA (Particle Size
Analyzer), and VNA (Vector Network Analyzer) to determine the functional groups,
the value of the electrical conductivity, particle size, and the absorption of
microwaves by a certain frequency range (range 8-12 GHz) contained in these
materials. The results of the study showed that the characterization based on
Polyaniline (PANi) which has been doped protonic acid (protonated) or has become
conducting polymers have peaks characteristic IR absorption band at wave number of
1141 cm-1-1177 cm-1. The particle size of each form of Polyaniline research has
become nanoparticles with a particle size range of each form of this material ranging
from 4-9 nm. Polyaniline which has the highest electrical conductivity by doping
Polyaniline protonic acid HClO4 (PANi (HClO4)) of 3,6 mS / cm and has a low
absorption of microwaves is -6,98 dB at a frequency of 11,34 GHz. Low permittivity
value owned by PANi (HClO4) but with a lower value of permittivity (negative
dielectric constant and minimum dielectric loss) and high electrical conductivity,
making the absorption of microwaves by PANi composites such as matrix will
increase the amount of microwave absorption and minimize microwave transmitted.
The highest microwave absorption of composite materials owned by the composite
with a mixture of modified PANi (PANi-ES) as a matrix and Barrium Hexaferrite
(BHF) which had been sonicated for 5 hours as a filler with a composition ratio wt%
modified PANi and BHF 30 : 70. The composite material is PANi(HClO4) / 5BHF
which has the highest absorption of microwaves -38,3 dB at a frequency of 12,28
GHz."
Universitas Indonesia, 2014
S58248
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ahmad Fuad Riyadi
"Telah disintesis polianilin PANi dengan bantuan surfaktan sodium dodecyl sulfate SDS untuk meningkatan nilai konduktivitasnya. Surfaktan yang digunakan merupakan surfaktan jenis anionik yang dapat memberikan ionnya sebagai dopan kepada polianilin sehingga memudahkan terjadinya delokalisasi elektron. Polianilin disintesis dengan metode polimerisasi oksidatif kimia menggunakan 75 gram ammonium persulfat APS yang dilarutkan pada 650 ml HCl 1,5M sebagai larutan inisiator dan 75 ml anilin yang dilarutkan pada 650 ml HCl 1,5M sebagai larutan monomer. Surfaktan SDS dilarutkan pada 200 ml HCl 1,5M dengan konsentrasi 0,25 , 0,67 , 1 dan 2. Polianilin yang telah disintesis menghasilkan bentuk basa emeraldin dan dibuat konduktif melalui proses protonasi menggunakan asam perklorat HClO4. Polianilin yang telah jadi dikarakterisasi dengan FTIR, PSA dan Four Point Probe. Struktur polianilin terkonfirmasi dari hasil karakterisasi FTIR pada bilangan gelombang 1488 dan 1566 cm-1 menandakan vibrasi dari ikataran rangkap C pada cincin benzenoid dan quinoid yang merupakan puncak karakteristik dari polianilin. Nilai ukuran partikel rata-rata dari polianilin yang disintesis dengan surfaktan berkisar pada 212 ndash; 401 nm. Nilai konduktivitas polianilin yang disintesis adalah 2,12 ; 2,94 ; 3,97 dan 0,1 untuk masing-masing konsentrasi SDS. Dari hasil penelitian ini didapatkan bahwa penambahan surfaktan anionik yaitu sodium dodecyl sulfat memberikan peningkatan pada nilai konduktivitas polianilin sekitar dua kali dari polianilin tanpa surfaktan.

Polyaniline PANi had been synthesized assisted by sodium dodecyl sulfate SDS surfactant to increase the value of conductivity. The surfactant used in this research was an anionic type, which can give its ion as dopan for polyaniline to facilitate the delocalization of electrons. Polyaniline was synthesized by chemical oxidative polymerization using 75 gram ammonium persulfate APS was dissolved in 650 ml HCl 1.5M as iniator solution and 75 ml aniline was dissolved in 650 ml HCl 1.5M as monomer solution. The SDS surfactant was dissolved in 200 ml HCl 1.5M with a variation of concentration 0.25 , 0.67 , 1 and 2. The synthesized polyaniline produces emeraldin base and became conductive after protonation process with percholic acid HClO4 . Polyaniline was characterized by FTIR, PSA and four point probe. The polyaniline structure was confirmed by FTIR characterization at wavenumbers 1488 and 1566 which denoting the vibrations of C, double bond at benzenoid and quinoid ring which are the characteristic peaks of polyaniline. The mean particle size of polyaniline assisted by surfactant ranging from 212 to 401 nm. The values of conductivity of polyaniline are 2.12, 2.94, 3.97 and 0.1 for each SDS concentration. From this research, it is concluded that the addition of anionic surfactant, like sodium dodecyl sulfate, increasing the conductivity value of polyaniline about two times than polyaniline without surfactants. "
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ahmad Luthfi Mahar
"Polyanilin (PANi) adalah salah satu jenis polimer konduktif yang masih mendapat perhatian besar dan menjadi subjek investigasi intensif sampai saat ini. Dalam studi ini, PANi disintesis melalui metode reaksi polimerisasi oksidatif kimia. Sampel untuk penyelidikan dipersiapkan melalui penggunaan surfaktan dengan tiga variasi yaitu, larutan reaksi tanpa menggunakan surfaktan, dengan menggunakan surfaktan sodium octylsulfate atau SOS (NaC8H17SO4) dan sodium dodecylsulfate atau SDS (NaC12H25SO4) masing-masing dengan konsentrasi 1%. Selama proses polimerisasi, data pH, viskositas, densitas, dan suhu larutan diukur secara berkala. Hasil dari reaksi adalah serbuk PANi basa emeraldin atau PANi-EB yang kemudian didoping dengan HClO4 untuk memperoleh sifat konduktivitas listrik. Semua PANi yang disintesis dievaluasi oleh FTIR, TGA, DSC, PSA dan FPP. Hasil penelitian ini menyimpulkan bahwa perpanjangan rantai karbon surfaktan tidak berkontribusi banyak terhadap peningkatan nilai konduktivitas listrik. Perpanjangan rantai karbon surfaktan hanya memengaruhi distribusi ukuran partikel. PANi konduktif dengan penambahan 1% SDS memiliki distribusi ukuran partikel dengan ukuran partikel rata-rata ~ 191 nm dan PANi konduktifif dengan penambahan 1% SOS memiliki ukuran partikel rata-rata 291 nm. Kedua nilai ini jauh lebih halus dibandingkan dengan nilai ukuran rata-rata partikel PANi bebas surfaktan (~ 723 nm). Konduktivitas listrik PANi / SOS 1% dan PANi / SDS 1% setelah didoping dengan HClO4 masing-masing adalah 1,16 S/cm dan 1,12 S/cm.

Polyaniline (PANi) is one type of conductive polymers which still receive large attentions and being a subject of intensive investigation up to date. In this study, PANi was synthesized by a chemical oxidative polymerization reaction method. Samples for under investigation were prepared through three fixed variations during polymerization reactions respectively, using no surfactants, with surfactants of sodium octylsulfate SOS (NaC8H17SO4) and sodium dodecylsulfate SDS (NaC12H25SO4) of 1% concentration. During the polymerization process data of pH, viscosity, density and temperature of solutions were collected periodically. The result of the reaction is an emeraldine base PANi or PANi-EB, which was then doped with HClO4 for obtaining the electrical conductivity property. All synthesized PANi were evaluated by FTIR, TGA, DSC, PSA and FPP. The research work of current study concluded that the extension of carbon chain of the surfactant did not contribute much the increase in conductivity values. The extension of the surfactant carbon chain only affected the particle size distribution. Conductictive PANi with the addition of 1% SDS has a particle size distribution with a mean particle size ~ 191 nm and that of 1 % SOS has a mean particle size ~ 291 nm, which are much finer than that of 291 nm of PANi free of surfactant (~ 723 nm). The electrical conductivity of PANi / SOS 1% and PANi / SDS 1% after doped with HClO4 were respectively 1.16 S/cm and 1.12 S/cm."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nayaka Wicaksana
"Penelitian ini memiliki fokus pada karakteristik PVA dengan nilai derajat hidrolisis dan derajat polimerisasi yang berbeda. Kajian terhadap karakteristik PVA dilakukan dengan menggunakan PVA Terhidrolisis Sebagian dan PVA Terhdirolisis Sempurna dengan derajat polimerisasi low, medium, dan, high. Metode penelitian dilakukan dengan mengamati proses pelarutan dari masing-masing jenis PVA dengan air pada konsentrasi 1%, 5%, dan 10% dengan pengaruh suhu untuk PVA Terhidrolisis Sempurna. Observasi pada proses pelarutan PVA mencakup pengaruh waktu dan suhu terhadap nilai konduktivitas, pH, kekentalan, dan kelarutan. Hasil yang diperoleh menunjukan PVA pada suhu ruang dengan konsentrasi 10 % untuk PVA Terhidrolisis Sebagian dengan derajat polimeriasi low menunjukan nilai konduktivitas 340 µS/cm. Nilai tersebut lebih tinggi dari konduktivitas air mineral yaitu 90 µS/cm. Suhu optimum pada pelarutan PVA Terhidrolisis Sempurna diperoleh di suhu 90 oC. Kemampuan PVA untuk berikatan dengan Polimer Kondukif ditentukan oleh jenis gugus molekul yang ada pada PVA. Gugus molekul PVA diamati dengan Fourier Transform Infrared Spectrophotometer (FTIR). Morfologi dan fisiologi dari larutan PVA diamati pada penelitian ini. Informasi terhadap kekuatan mekanis PVA diperoleh dengan mengamati karakteristik lapis tipis PVA. Lapis tipis PVA dibuat dengan melakukan proses pengeringan larutan PVA pada suhu 60℃ selama 24 jam. Informasi karakteristik PVA yang tepat untuk penggunaan PVA pada Polimer Konduktif dikaji dalam skripsi ini.

This research focus on studying the properties of PVA with different degree of hydrolysis and different degree of polymerization. The study of PVA properties was conducted with Partially Hydrolyzed PVA and Fully Hydrolyzed PVA. The degree of polymerization was divided into three categories of respectively low, medium, and high. Study on the properties of degree of hydrolysis and degree of polymerization was conducted on solution containing 1%, 5% and 10% PVA with the influence of temprature change on Fully Hydrolyzed PVA. Dissolution time, conductivity, pH, and viscosity towards time and temprature was observed during dissolution process. The highest electrical conductivity value was 340 µS/cm for Partially Hydrolyzed PVA with 10% concentration and low degree of polymerization. This number was higher than electircal conductivity of mineral water which has electrical conductivity value of 90 µS/cm. Molecular groups of PVA determines the PVA ability to create bond with Conductive Polymer. PVAs molecular groups was observed with Fourier Transform Infrared Spectrophotometer (FTIR). This study also observed the morphology and physiology of PVA properties. The information of PVA mechanical properties was obtained by observing PVA thin film properties. PVA thin film was obtained by drying PVA solution for 24 hours at 60oC. The suitable PVA properties for Conductive Polymer was discussed further on this report."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muhammad Freddy Kissinger
"Polypyrrole adalah salah satu jenis polimer konduktif yang banyak diteliti hingga saat ini. Penelitian ini berusaha menggunakan PVA untuk menambahkan sifat lain pada PPy dan mencari tahu pengaruh PVA untuk sifat konduktivitas PPy. Penelitian dilakukan menggunakan PVA dengan jenis terhidrolisis sebagian dan derajat polimerisasi medium. Variasi konsentrasi PVA yang digunakan adalah 1%, 2%, 3%, dan 5%. Selama proses polimerisasi, pengukuran parameter seperti pH, suhu, viskositas, dan densitas dilakukan secara berkala. Hasil PPy yang disintesis kemudian dievaluasi dengan FTIR, Conductometry, PSA, FPP. Hasil dari penelitian ini menyimpulkan bahwa PVA bisa menambah konduktivitas dari PPy dengan polimerisasi emulsi metode oksidatif kimia. Konduktivitas PPy tanpa PVA dengan PPy-PVA 1%, PPy-PVA 2%, dan PPy-PVA 3% secara berurutan adalah 52008 (µs/cm), 55088 (µs/cm), 57088 (µs/cm), dan 62688 (µs/cm). PVA bisa memberi sifat baru yang sebelumnya tidak terdapat pada PPy seperti elastisitas dan kemampuan untuk membuat lapis tipis sehingga memungkinkan untuk membuat pelapis material menggunakan PPy-PVA.

Polypyrrole is a type of conductive polymer that has been studied to date. This study attempts to use PVA to add other properties to PPy and find out the effect of PVA on the conductivity of PPy. The study was conducted using PVA with a partially hydrolyzed type and medium degree of polymerization. Variations in PVA concentrations used are 1%, 2%, 3%, and 5%. During the polymerization process, measurements of parameters such as pH, temperature, viscosity, and density are carried out periodically. The results of the synthesized PPy were then evaluated by FTIR, Conductometry, PSA, FPP. The results of this study concluded that PVA could increase the conductivity of PPy by emulsion polymerization of oxidative chemical methods. The conductivity of PPy without PVA with PPy-PVA 1%, PPy-PVA 2%, and PPy-PVA 3% respectively were 52008 (µs / cm), 55088 (µs / cm), 57088 (µs / cm), and 62688 ( µs / cm). PVA can give new properties that were not previously found in PPy such as elasticity and the ability to make thin layers making it possible to make a coating of material using PPy-PVA."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Adrian Julio Adhy Putra
"Penelitian ini berfokus pada sintesis serta menganalisa sifat dan karakteristik dari sistem komposit yang tersusun oleh polipirol dan titanium oksida. Polipirol disintesis dengan menggunakan metode polimerisasi oksidasi kimia dari monomer pirol menggunakan oksidan ammonium persulfate (APS) dalam dua variasi media pelarut H2O serta H2SO4, reaksi berlangsung dengan menggunakan tehnik batch selama 4 jam serta menggunakan kecepatan magnetic stirrer sebesar 300 rpm yang dilakukan dalam temperature ruang yang berkisar antara 23-240C, Karakterisasi PPy selama proses reaksi polimerisasi berlangsung dilakukan terhadap parameter pH didapatkan bahwa PPy dengan pelarut H2SO4 memiliki nilai tingkat keasaman yang lebih tinggi yang berkisar 0.1-0.5 dibandingkan PPy dengan pelarut H2O yang berkisar 1-1.3, nilai konduktivitas (σ) yang dihasilkan oleh PPy dengan pelarut H2SO4 lebih tinggi (0.813 s/m) dibandingkan PPy dengan pelarut H2O. Berdasarkan dari pengujian konduktivitas yang dilakukan pada pembentukan sistem komposit PPy/TiO2 dapat diketahui bahwa semakin tinggi persentase TiO2 dalam pembentukan sistem komposit PPy/TiO2 maka semakin rendah nilai konduktivitas yang dihasilkan dalam sistem komposit PPy/TiO2 serta sistem komposit PPy/TiO2 yang menggunakan PPy dengan pelarut H2SO4 memiliki nilai konduktivitas yang lebih tinggi dibandingkan dengan sistem komposit PPy/TiO2 yang menggunakan PPy dengan pelarut H2O

This research focuses on the synthesis and analyzes the properties and characteristics of the composite system composed of polypyrrole and titanium oxide. Polypyrrole was synthesized using the chemical oxidation polymerization method from pyrrole monomers using the oxidant ammonium persulfate (APS) in two variations of H2O and H2SO4 solvent media, the reaction took place using a batch technique for 4 hours and using a magnetic stirrer speed of 300 rpm which was carried out at room temperature which ranged from 23-240C, The characterization of PPy during the polymerization reaction process was carried out on the pH parameter, it was found that PPy with H2SO4 solvent had a higher acidity level value ranging from 0.1-0.5 compared to PPy with H2O solvent which ranged from 1-1.3, the conductivity value (σ) produced by PPy with H2SO4 solvent higher (0.813 s/m) than PPy with H2O solvent. Based on the conductivity tests carried out on the formation of the PPy/TiO2, composite system, it can be seen that the higher the percentage of TiO2 in the formation of the PPy/TiO2 composite system, the lower the conductivity value produced in the PPy/TiO2 composite system and the PPy/TiO2 composite system using PPy with solvent H2SO4 has a higher conductivity value compared to the PPy/TiO2 composite system that uses PPy with H2O solvent.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3   >>