Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 244 dokumen yang sesuai dengan query
cover
Muhammad Nafiza Reyhananda Setiawan
"Potensi energi terbarukan di Indonesia khususnya untuk bahan bakar alternatif semakin menjanjikan. Mikroalga merupakan jenis biomassa yang potensial sebagai bahan baku biofuel. Untuk memperbanyak mikroalga diperlukan proses kultivasi dengan metode tertutup yaitu menggunakan fotobioreaktor sehingga parameter hidrodinamika dan perpindahan massanya dapat terkontrol dengan baik khususnya biofiksasi CO2 dengan gelembung mikro. Parameter hidrodinamika seperti diameter gelembung, kecepatan gelembung, bilangan non dimensional dan terminal velocity sangat berpengaruh terhadap proses kultivasi mikroalga. Penelitian ini bertujuan untuk mengetahui karakteristik bentuk aliran terosilasi pada Sweeping Jet Fluid Oscillator dengan 6 variasi kecepatan yaitu l-6 lpm serta mengetahui karakteristik gelembung mikro yang dihasilkan 3 metode aliran aerasi berbeda yaitu tanpa fluid oscillator, merged output fluid oscillator dan splited output fluid oscillator. Validasi aliran di dalam fluid oscillator dan fotobioreaktor dilakukan dengan simulasi menggunakan software ANSYS 2022R1. Hasil data berupa video direkam oleh High Speed Camera Phantom VEO 1310S yang nantinya akan diolah dengan menggunakan software image processing PIVlab dan ImageJ. Berdasarkan hasil analisis data, seiring meningkatnya debit aliran pada Sweeping Jet Fluid Oscillator, maka frekuensi osilasi akan semakin tingi dan aliran berubah dari aliran laminar menjadi transisi. Hasil validasi simulasi CFD dengan eksperimen untuk aliran di dalam sweeping jet fluid oscillator menunjukkan bahwa aliran terbukti berosilasi dan memiliki kecepatan aliran yang tidak jauh berbeda dengan error dibawah 6 %. Metode aliran Splitted Ouput Fluid Oscillator merupakan pilihan terbaik untuk menghasilkan diameter gelembung yang kecil (267.370 um), kecepatan gelembung yang kecil (0.050 m/s) dan distribusi gelembung yang lebih seragam. Sehingga metode ini dapat menjadi acuan untuk penelitian selanjutnya khususnya untuk aplikasi kultivasi mikroalga.

The potential of renewable energy in Indonesia, especially for alternative fuels, is increasingly promising. Microalgae is a type of biomass that has potential as a biofuel raw material. To cultivate and produce microalgae, a cultivation process with a closed method is needed, namely using a photobioreactor so that the hydrodynamics and mass transfer parameters can be well controlled, especially biofixation of CO2 with microbubbles. Hydrodynamic parameters such as bubble diameter, bubble velocity, non-dimensional number, and terminal velocity are very essential in the microalgae cultivation process. This study aims to determine the characteristics of the oscillating flow shape in the Sweeping Jet Fluid Oscillator with 6 velocity variations (l6 lpm), and to determine the characteristics of microbubbles produced by 3 different aeration flow methods, namely without fluid oscillator, merged output fluid oscillator and splited output fluid oscillator. Validation of the flow inside the fluid oscillator and photobioreactor is done by simulation using ANSYS 2022R1 software. Result data was obtained through video recorded by the High Speed Camera Phantom VEO 1310S which will be processed using image processing software PIVlab and ImageJ. Based on the results of the data analysis, as the flow rate increases in the Sweeping Jet Fluid Oscillator, the oscillation frequency will be higher, and the flow changes from laminar flow to transition flow. The validation results of CFD simulations with experiments for the flow inside the sweeping jet fluid oscillator show that the flow is proven to oscillate and has a flow velocity that is not much different with an error below 6%. The Splitted Output Fluid Oscillator flow method is the best choice to produce a smaller bubble diameter (267.370 um), smaller bubble velocity (0.050 m/s), and more uniform bubble distribution. So this method can be a reference for further research, especially for microalgae cultivation applications."
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Elang Pramudya Wijaya
"ABSTRAK
Data statistik ketenagalistrikan pada tahun 2018 menyebutkan bahwa, masih terdapat masyarakat Indonesia yang belum mendapatkan akses khususnya provinsi Nusa Tenggara Timur yang masih bernilai 61.9%. Tidak tersedianya akses distribusi akibat mahalnya biaya instalasinya dan sulitnya akses menuju lokasi. Oleh karena itu, pembangkit listrik mandiri berbahan baku renewable energy merupakan solusi yang tepat untuk mengatasi krisis energi di daerah terpencil di Indonesia. Disamping itu, potensi energi air di Indonesia mempunyai total potensi sebesar 75 GW. Ini menjadi dasar dari beberapa hasil kajian, turbin pikohidro merupakan solusi yang tepat untuk meningkatkan rasio elektrifikasi di daerah terpencil. Tujuan dalam studi ini adalah memverifikasi fenomena aliran yang terdapat pada sudu turbin piko hidro jenis cross flow pada CFD berdasarkan metode eksperimen Particle Image Velocimetry. Simulasi akan menggunakan ANSYS Fluent 18.1 dengan fitur steady dengan tinggi jatuh air sebesar 1.4 m dan debit aliran 0.01167 m3/s. Ukuran timestep yang digunakan adalah 0.002. Metode eksperimen menggunakan Particle Image Velocimetry dengan Dantec Dynamic laser system. Hasil komputasi divalidasi dengan metode PIV, ditunjukkan oleh distribusi kecepatan pada nosel dan fenomena separasi fluida yang terjadi pada bagian raner turbin arus lintang. Studi ini, menyimpulkan bahwa fenomena pada kondisi sebenarnya dapat digambarkan oleh metode Particle Image Velocimetry dengan proporsi seeding particle dengan diameter maksimum 100 micron.

ABSTRACT
Based on electricity data in 2018, there are still Indonesian people who do not have access to electricity by 2% (Indonesia). As many as 2% of people who have not received electricity are in remote areas. This is due to the unavailability of distribution access due to the very high installation costs and access to difficult locations. Thus, an independent power plant made from renewable energy is the right solution to overcome the energy crisis in remote areas in Indonesia. furthermore, the potential of water energy in Indonesia has a total potential of 75 GW. This is the basis of several studies, pico hydro turbines are the right solution to increase the electrification ratio in remote areas (Diah; Sarasa; Sari). The purpose of this study is to verify the flow phenomena contained in the crossflow turbine blades on CFD based on the Particle Image Velocimetry experimental method. The simulation will use ANSYS Fluent 18.1 with the steady feature with a head of 1.4 m and a flow rate of 0.01167 m3/ s. The timestep size used is 0.002. The experimental method uses Particle Image Velocimetry with the Dantec Dynamic laser system. The results of computation are then validated by the PIV method, shown by the velocity distribution in the nozzle and the flow phenomenon in the crossflow turbine runner section. This study concludes that the phenomenon of actual conditions can be described by the Particle Image Velocimetry method with the proportion of seeding particles with a maximum diameter of 100 microns.
"
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Christopher Clement Rusli
"Berdasarkan data tahun 2018, 1.7% daerah di Indonesia belum terelektrifikasi dengan baik, dimana persentase sebesar 38.1% berasal dari daerah terpencil di NTT. Daerah terpencil merupakan daerah yang memiliki rasio elektrifikasi rendah. Daerah terpencil merupakan daerah dengan penduduk sedikit, memiliki ekonomi yang relatif rendah, akses ke daerah yang sulit, serta mata pencaharian utama sebagai petani atau nelayan. Pembangkit listrik tenaga air skala piko hidro merupakan salah satu solusi yang memungkinkan untuk daerah terpencil karena biaya pembuatan yang relatif murah, perawatan sederhana, dan juga konsumsi listrik pada daerah pedesaan yang tidak begitu besar. Turbin vortex merupakan salah satu jenis turbin skala piko hidro yang dapat dimanfaatkan dikarenakan banyaknya aliran sungai di Indonesia yang memiliki kondisi tinggi jatuh yang rendah. Studi ini bertujuan untuk mengamati kinerja hidrolik dari sudu straight dan curved secara analitik serta numerik dengan menggunakan computational fluid dynamics (CFD). Dua buah metode dilakukan dalam studi ini, analitik dan numerik. Metode analitik digunakan untuk menghitung geometri dari saluran serta sudu, dan juga kinerja hidrolik sudu. Metode numerik digunakan juga untuk mengamati kinerja sudu. Dengan menggunakan fitur moving mesh, daya sudu dapat diamati dalam kondisi putaran yang berbeda. Putaran sudu yang digunakan dalam studi ini adalah 150, 200, 250, 300, dan 350 Rpm. Studi ini menunjukan bahwa pada kondisi 250 rpm, kedua sudu dapat mencapai kinerja hidrolik optimalnya dengan nilai sebesar 0.63%. Dari hasil numerik, dapat dikatakan bentuk sudu seperti ini tidak menyerap energi kinetik dengna baik.

Based on 2018 data, 1.7% of regions in Indonesia do not yet have good electricity, with a percentage of 38.1% obtained from regions available in NTT. Remote areas are the areas that have a low electrification ratio. Remote areas have a relatively low population and economy, difficult access, and livelihoods as farmers or fishermen. Pico-hydro scale hydroelectric power plants are one of the possible solutions to create a relatively cheap budget, simple maintenance, and also electricity consumption in areas that are not so large. Vortex turbine is one type of pico hydro turbine that can be utilized because of the many rivers flows in Indonesia that has high excess. Analytic and numerical straight and curved angles use the fluid competency dynamics CFD. Two methods are carried out in this studio, analytic and numerical. Analytical methods are used to calculate channel geometry which will then discuss flow with numerical methods. Analytical methods are also used to determine the hydraulic efficiency of the blades used. Hydraulic performance is the transition between the power generated by the turbine and the fluid power used to drive the turbine. Numerical methods are also used for blades. By using the movable mesh feature, the blade can be seen in various rotational conditions. Details of the slats used in this studio are 150, 200, 250, 300, and 350 Rpm. This study produces 250 rpm, both blades can achieve optimal hydraulic performance with a value of 0.63%. From the numerical results, both of the blade shapes dont absorb kinetic energy properly.
"
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rhafif Adli Dzakiariq
"Permasalahan iklim global yang sangat serius dimana global warming telah memberikan kontribusi besar pada kenaikan suhu global. Tidak dapat dipungkiri kenaikan rata-rata suhu global telah mencapai 1.25°C pada Agustus 2023 bahkan menurut para peneliti ada kemungkinan sebesar 66% bahwa kenaikan suhu global akan melewati angka 1.5°C antara saat ini hingga tahun 2027. Pertumbuhan laju kenaikan suhu bumi ini mayoritas disebabkan oleh aktivitas hidup umat manusia dimana emisi CO2 pada sektor energi yakni emisi hasil pembakaran minyak, gas, dan batu bara menjadi penyebab terbesar terjadinya kenaikan rata-rata suhu global yang signifikan. dari itu, perlu adanya peralihan penggunaan energi berbasis fossil menuju energi baru terbarukan dengan bertujuan untuk menekan angka kenaikan suhu bumi dengan salah satunya memanfaatkan energi arus laut dengan menggunakan turbin tidal yang mana akan berputar akibat adanya pasang surut arus laut yang menyebabkan energi kinetik air laut untuk menghasilkan energi listrik. Pada dasarnya cara kerja turbin tidal mirip seperti turbin angin begitupun cara kerja nya. Namun, kedua jenis turbin tersebut menggunakan fluida yang berbeda. Dibandingkan dengan turbin angin, turbin tidal lebih banyak memiliki keuntungan diantaranya ketersediaan energi yang lebih teratur dan dapat diprediksi karena pasang surut memiliki pola yang dapat dihitung dan pasang surut memiliki perubahan yang cenderung stabil. Agar kinerja turbin tidal menjadi lebih efisien, penggunaan diffuser dan brim telah terbukti dapat meningkatkan efisiensi turbin dengan adanya efek vortex yang terjadi. Dari studi ini, kami menganalisis dampak penggunaan diffuser dan brim yang diaplikasikan bersamaan dengan blade aerofoil NACA 4418 yang mana hasilnya menyatakan bahwa semakin tinggi ketinggian brim yang digunakan, maka hasil power coefficient yang dihasilkan akan semakin tinggi, dalam studi ini, kami memvariasikan penggunaan diffuser 10,43° dan 15,34° dengan variasi brim 0,1D dan 0,3D serta variasi TSR 1-4. Hasil studi menunjukkan bahwa nilai power coefficient tertinggi terdapat pada penggunaan diffuser 15,34° dengan brim 0,3D pada TSR 3 dengan nilai 47,5%.

The global climate problem is very serious, with global warming having significantly contributed to the rise in global temperatures. It is undeniable that the average global temperature increase reached 1.25°C in August 2023. Moreover, researchers estimate a 66% chance that global temperature increases will exceed 1.5°C between now and 2027. This rapid increase in Earth's temperature is largely caused by human activities, with CO2 emissions from the energy sector—specifically from the burning of oil, gas, and coal—being the largest contributor to the significant rise in average global temperatures. Therefore, there is a need to transition from fossil fuel-based energy to renewable energy sources with the aim of reducing the rate of temperature increase. One of the ways to achieve this is by harnessing tidal energy using tidal turbines, which rotate due to the tidal currents, converting the kinetic energy of seawater into electrical energy. Essentially, the working principle of a tidal turbine is similar to that of a wind turbine, but the two types of turbines use different fluids. Compared to wind turbines, tidal turbines have several advantages, including a more regular and predictable energy supply since tides follow calculable patterns and tend to have stable variations. To enhance the efficiency of tidal turbines, the use of diffusers and brims has been proven to increase turbine efficiency through the vortex effect. In this study, we analyzed the impact of using diffusers and brims in conjunction with NACA 4418 aerofoil blades. The results indicated that the higher the brim used, the higher the resulting power coefficient. In this study, we varied the use of diffusers with angles of 10.43° and 15.34°, brim heights of 0.1D and 0.3D, and TSR (Tip Speed Ratio) from 1 to 4. The study results showed that the highest power coefficient was achieved with a 15.34° diffuser and a 0.3D brim at a TSR of 3, with a value of 47.5%."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Farel Athallah Aqil
"Kebutuhan energi listrik global pada tahun 2022 mencapai 3,63 MWh per kapita didominasi dari pembangkit listrik batu bara, dan gas,. 61,55% sumber energi listrik di Indonesia berasal dari batu-bara. Transisi menuju energi baru terbarukan disepakati oleh seluruh negara dunia yang tertuang pada paris agreement dan COP 27 dengan target membatasi suhu global hingga 1.5 oC diatas tingkat pra industrialisasi. Indonesia menghadapi tantangan dalam transisi menuju energi baru terbarukan dimana terjadi penurunan penggunaan energi baru terbarukan dari 11,5% pada 2021 menjadi 10,4% pada 2022. Energi terbarukan yang bisa dimanfaatkan Indonesia salah satunya adalah energi pasang surut. Letak geografis indonesia yang merupakan negara kepulauan menyimpan potensi energi tidal yang sangat besar. Kecepatan arus pasang surut di Indonesia sendiri mencapai 2,8 m/s. Dibutuhkan studi lebih lanjut untuk mendapatkan turbin tidal yang ideal. Literatur terkait upaya meningkatkan nilai power coefficient turbin tidal membuktikan bahwa profil airfoil NACA 4418 yang dikenal memiliki stall delay dan ketahanan terhadap roughness mampu meningkatkan kinerja dari turbin tidal sumbu horizontal. Selain itu, penggunaan diffuser juga dapat meningkatkan power coefficient turbin dimana semakin besar sudut diffuser yang digunakan maka semakin besar nilai power coefficient yang dapat dihasilkan. Berdasarkan hasil eksperimen dengan variasi sudut diffuser 10,43° dan 15,34° didapatkan power coefficient tertinggi sebesar 34,8%.

The global electricity demand in 2022 reached 3.63 MWh per capita, dominated by coal and gas power plants. In Indonesia, 61.55% of electricity comes from coal. The transition to renewable energy was agreed upon by all countries as outlined in the Paris Agreement and COP 27, with the goal of limiting the global temperature rise to 1.5°C above pre-industrial levels. Indonesia faces challenges in transitioning to renewable energy, with the share of renewable energy decreasing from 11.5% in 2021 to 10.4% in 2022. One of the renewable energy sources that Indonesia can harness is tidal energy. Indonesia's geographic location as an archipelago holds great potential for tidal energy, with tidal current speeds reaching up to 2.8 m/s. Further studies are needed to develop the ideal tidal turbine. Relevant literature on efforts to increase the power coefficient of tidal turbines shows that the NACA 4418 airfoil profile, known for its stall delay and roughness resistance, can enhance the performance of horizontal-axis tidal turbines. Additionally, the use of diffusers can also improve the power coefficient of the turbine, with larger diffuser angles resulting in higher power coefficients. Based on experimental results with diffuser angles of 10.43° and 15.34°, the highest power coefficient obtained was 34.8%."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Darren Nathanael Tanudirdjo
"ABSTRACT
Modern composter technology has been able to process domestic waste easily. As for the conveniences offered, modern composter must still be operated manually using human power to stir the waste heap. Then there is the problem of quality control, which requires sufficient experience from the user side to process good compost and can be a challenge for new users. Therefore, the aim of this project is to mechanize the process of stirring and quality control to minimize the level of difficulty in the composting process, as well as provide guidance for similar research to be carried out. This project will only cover 3 stages in the design process (Function, Synthesis, and Detail), with design guidelines using existing literature studies. For example, composter design is based on factors that influence the quality of compost, and the choice of sensor type is based on parameters that must be measured and controlled. Everything will be supported by solar panels as a power source that is connected externally via port D.C. to the logic board, which will direct power to all motors and sensors, and control the feedback loop of the sensor data obtained. There are also guidelines for controlling the types of waste that can and cannot be processed by composter, and also the optimal condition of composter to work properly. However, there are some important points to consider before advancing to the next design phase. These points are issues related to price and market share, new ideas for mechanical processes, and issues related to total mass and product portability. The current composter model is still too heavy, and by changing the material used, the total weight can be reduced threefold by increasing the total price to 3 times the initial price that has been determined. This creates a new problem when marketing this product because the specified target price is 4 times the price of the most expensive composter sold in the Australian market. Then there are things that can be updated such as cable routes, automatic cooling systems, and humidity control mechanisms where ideas and technology are available but still need more time to perfect. Therefore, this idea still needs improvement, and further research is still needed to resolve issues related to this idea before advancing to the next phase, with additional research related to analyzing the market share related to this composter.

ABSTRAK
Teknologi komposter modern telah mampu mengolah limbah domestik dengan mudah. Adapun kenyamanan yang ditawarkan, komposter modern masih harus dioperasikan secara manual menggunakan tenaga manusia untuk mengaduk tumpukan sampah. Lalu ada masalah kontrol kualitas, yang membutuhkan pengalaman yang cukup dari sisi pengguna untuk memproses kompos yang baik dan bisa menjadi tantangan bagi pengguna baru. Oleh karena itu, tujuan dari proyek ini adalah untuk memekanisasi proses pengadukan dan kontrol kualitas untuk meminimalkan tingkat kesulitan dalam proses pengomposan, serta memberikan panduan untuk penelitian serupa yang akan dilakukan. Proyek ini hanya akan mencakup 3 tahap dalam proses desain (Fungsi, Sintesis, dan Detail), dengan pedoman desain menggunakan studi literatur yang ada. Misalnya, desain komposter didasarkan pada faktor-faktor yang mempengaruhi kualitas kompos, dan pilihan jenis sensor didasarkan pada parameter yang harus diukur dan dikendalikan. Semuanya akan didukung oleh panel surya sebagai sumber daya yang terhubung secara eksternal melalui port D.C. ke papan logika, yang akan mengarahkan daya ke semua motor dan sensor, dan mengontrol putaran umpan balik dari data sensor yang diperoleh. Ada juga pedoman untuk mengendalikan jenis limbah yang dapat dan tidak dapat diproses oleh komposter, dan juga kondisi optimal komposter agar bekerja dengan baik. Namun, ada beberapa poin penting yang perlu dipertimbangkan sebelum melanjutkan ke fase desain berikutnya. Poin-poin ini adalah masalah yang terkait dengan harga dan pangsa pasar, ide-ide baru untuk proses mekanis, dan masalah yang terkait dengan massa total dan portabilitas produk. Model komposter saat ini masih terlalu berat, dan dengan mengubah bahan yang digunakan, berat total dapat dikurangi tiga kali lipat dengan menaikkan harga total menjadi 3 kali lipat dari harga awal yang telah ditentukan. Ini menciptakan masalah baru ketika memasarkan produk ini karena target harga yang ditentukan adalah 4 kali lipat dari harga komposter paling mahal yang dijual di pasar Australia. Lalu ada hal-hal yang dapat diperbarui seperti rute kabel, sistem pendingin otomatis, dan mekanisme kontrol kelembaban di mana ide dan teknologi tersedia tetapi masih membutuhkan lebih banyak waktu untuk menyempurnakan. Oleh karena itu, ide ini masih perlu ditingkatkan, dan penelitian lebih lanjut masih diperlukan untuk menyelesaikan masalah yang terkait dengan ide ini sebelum maju ke tahap berikutnya, dengan penelitian tambahan terkait dengan menganalisis pangsa pasar terkait dengan komposter ini."
2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aqiel Saiful Fatah
"Sumber energi terbarukan adalah solusi yang mungkin untuk meningkatnya kekhawatiran energi bahan bakar fosil yang terbatas dan tenggat waktu yang semakin dekat dari Perjanjian Paris. Indonesia sebagai negara kepulauan dapat berkontribusi terhadap pengurangan emisi karbon melalui pemanfaatan energi arus laut untuk listrik. Turbin aliran arus laut telanjang hanya dapat mengubah 59% energi kinetik menjadi energi mekanik. Modifikasi dengan diffuser dapat meningkatkan efisiensinya. Studi ini membandingkan turbin pasang surut diffuser dengan sudut diffuser 10,43 dan 20,04 dari penelitian sebelumnya, dan 28.6° melalui koefisien daya mereka. Studi sebelumnya menemukan korelasi di mana penurunan rasio penyumbatan menyebabkan penurunan deviasi hasil eksperimen dari hasil numerik. Penambahan diffuser ketiga berharap untuk membuktikan fenomena ini. Percobaan dilakukan dalam tangki aliran di mana arus 0,7m / s diinduksi ke turbin pasang surut diffuser augmented. Turbin terhubung ke pengaturan meter torsi di mana torsi yang dihasilkan pada kecepatan rotasi yang berbeda dicatat. Dari sana kita dapat menemukan koefisien daya dalam hal rasio kecepatan tip. Diffuser 28.6° mencapai koefisien daya 0,41 pada rasio kecepatan tip 2,91. Dengan peningkatan rasio penyumbatan menjadi 31% dalam percobaan ini hasilnya menyimpang dari hasil numerik sebesar 9.47%. Selanjutnya koefisien daya maksimum dari diffuser 28.6° memiliki nilai di atas dua diffusers lainnya, tetapi secara numerik harus memiliki nilai yang lebih tinggi. Ada efek rasio penyumbatan terhadap efisiensi. Rasio penyumbatan harus menjadi pertimbangan ketika menerapkan turbin pasang surut diffuser augmented. Studi lebih lanjut diperlukan untuk menentukan nilai maksimum rasio penyumbatan sehingga efisiensi turbin tidak terlalu terpengaruh.

Renewable energy sources are a probable solution to the growing concern of finite fossil-fuel energy and the approaching deadline of the Paris Agreement. Indonesia as an archipelago nation can contribute to carbon emission reduction through utilizing tidal energy for electricity. A bare tidal stream turbine can only convert 59% of kinetic energy into mechanical energy. Diffuser augmentation can improve its efficiency. This study compared diffuser augmented tidal turbines with diffuser angles of 10.43 and 20.04 of previous studies, and 28.6° through their power coefficient. Previous studies found a correlation where a decrease in blockage ratio caused a decrease in deviation of experimental results from the numerical results. The addition of the third diffuser hopes to prove this phenomenon. The experiment is conducted in a flow tank where a current of 0.7m/s is induced to the diffuser augmented tidal turbine. The turbine is linked to a torque meter setup where the torque produced at different rotational speeds are recorded. From there we can find the power coefficient in regards to tip speed ratio. The 28.6° diffuser attained a power coefficient of 0.41 at a tip speed ratio of 2.91. With the increase in blockage ratio to 31% in this experiment the results deviated from the numerical results by 9.47%. Furthermore the maximum power coefficient of the 28,6 diffuser sits slightly above the two other diffusers, but numerically it should have the higher value. There is an effect of blockage ratio towards the efficiency. Blockage ratio should be a consideration when implementing diffuser augmented tidal turbines. Further study is needed to determine the maximum value of blockage ratio so the efficiency of the turbine is not greatly affected."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
M. Faiz Naufal
"Pengoperasian kereta api cepat menjadi salah satu perhatian dalam penelitian dan pengembangan industri kereta. Kecelakaan kereta yang diakibatkan oleh bencana dan kondisi pengoperasian yang tidak aman harus dicegah. Crosswind adalah salah satu ancaman yang dapat mengakibatkan kecelakan kereta. Crosswind effect dapat membuat kereta cepat terbalik pada saat kereta mengalami beban aerodinamika dikarenakan adanya normal dan tangensial stress pada permukaan kereta. Skripsi ini bertujuan untuk mencari dan menganalisa performa aerodinamika yang paling optimum dari beberapa kereta yang diuji ketika mengalami crosswind effect spesifik pada saat kereta berada dalam kondisi non-elevated. Model kereta yang digunakan adalah model kereta cepat Jakarta-Bandung Railway Project, yaitu kereta CR400 AF Fuxing Train yang telah disederhanakan. Simulasi akan dilakukan menggunakan computational fluid dynamics dan mencari parameter aerodinamika dan aliran pada kereta api cepat pada saat mengalami crosswind dengan menggunakan realizable k-ε turbulence model.

The operation of high-speed trains has become one of the concerns of current railway research and development. Fatal railway accidents, which are catastrophic consequences of unsafe operating conditions, should be prevented. Crosswinds are one of the major threats that can cause fatal railway accidents. Crosswind effect can flip and overturn the high-speed train as the train experiences aerodynamic loads due to the normal and tangential stresses in its surfaces when it cruises. This thesis aims to find and analyze the most optimum aerodynamics performance for the high-speed trains when experiencing crosswind effects from several train models specifically on non-elevated conditions (ground conditions). The train models used the simplified train model of the Jakarta-Bandung Railway Project which is CR400 AF Fuxing Train. The simulation will be conducted using computational fluid dynamics and try to obtain the aerodynamic parameters and flow process of the high-speed trains due to crosswind using realizable k-ε turbulence model."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ega Leonar Soekarno
"Ketika kereta api berkecepatan tinggi memasuki ruang terbatas seperti terowongan, udara di dalam terowongan mengalami kesulitan untuk menyebar di sekitarnya karena ruang udara yang terbatas. Oleh karena itu, ia menghasilkan gelombang tekanan yang merambat melalui panjang terowongan ke portal keluar dengan kecepatan suara. Perubahan tekanan udara dan implikasinya terhadap keselamatan pengoperasian kereta api, kenyamanan penumpang, dan dampak lingkungan yang ditimbulkan oleh kereta api berkecepatan tinggi yang memasuki terowongan merupakan bagian penting dari aerodinamika kereta api. Ini juga merupakan masalah utama untuk membiarkan kereta berjalan pada kecepatan yang lebih tinggi. Berbeda dengan di udara terbuka, kereta api yang memasuki terowongan bertindak sebagai piston yang bergerak melawan udara yang menempati ruang terowongan yang dibatasi oleh dinding terowongan dan dengan demikian, "efek piston" dihasilkan. tesisnya bertujuan untuk menjelaskan parameter yang mempengaruhi kecepatan udara dan medan tekanan yang diinduksi, menciptakan efek piston di terowongan. Model kereta api dan terowongan yang berskala dan disederhanakan diikuti dengan simulasi numerik telah dilakukan untuk menganalisis kontur dan amplitudo kecepatan dan tekanan udara yang berfluktuasi di dalam terowongan dan di dalam kereta. Model ini akan menjadi model standar yang digunakan dalam percobaan ini untuk menyelidiki efek aerodinamis. Simulasi menggunakan CFD komputasi dengan tipe analisis transien.

When a high-speed train enters a confined space such as a tunnel, the air inside the tunnel has difficulty diffusing around it because of the restricted airspace. Hence, it generates a pressure wave that propagates through the tunnel’s length to the exit portal at the speed of sound. Air pressure change and its implications on the safe operation of trains, passengers comfort, and environmental impact caused by a high-speed train entering a tunnel are important parts of train aerodynamics. It is also a key issue to let trains run at a higher speed. Unlike the case in the open air, a train that enters a tunnel acts as a piston that moves against the air that occupies the tunnel space which is constrained by the tunnel walls and thus, a “piston effect” is generated. his thesis aimed to explain the parameters affecting the induced air velocity and pressure fields, creating the piston effect in the tunnel. Scaled and simplified model of the train and tunnel followed with numerical simulations have been carried out to analyzed the contour and amplitude of fluctuating air velocity and pressure in the tunnel and on the train. The generic train model to represent the original high-speed train inside a tunnel. This model will be the standard model used in this experiment to investigate the aerodynamic effect. The simulation uses computational CFD with transient analysis type."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Amalia Pradipta Arsyad
"Penyimpanan energi panas sistem adsorpsi memiliki reaksi bolak-balik dimana terjadi reaksi eksotermik ketika proses adsorpsi dan reaksi endotermik ketika proses desorpsi. Sistem ini memungkinkan penyimpanan panas untuk sumber energi yang tidak kontinu seperti sumber energi matahari dan sisa panas buang industri. Ketika proses adsorpsi berlangsung, panas dilepaskan dari adsorben dan dihitung sebagai jumlah panas adsorpsi yang dapat disimpan. Zeolite alam merupakan adsorben dengan potensi yang cukup besar mengingat panas adsorpsi yang cukup tinggi, karakteristiknya yang berporos, luas permukaan yang besar, dan kemampuannya untuk meng-adsorp molekul yang sangat kecil seperti air. Selain itu, zeolite alam merupakan bahan alami yang potensi sumber dayanya cukup besar di Indonesia. Dalam penelitian ini, dilakukan analisis terhadap kemampuan penyimpanan panas sistem adsorpsi menggunakan pasangan zeolite alam-air sebagai adsorben-adsorbat untuk temperature pemanasan 160°C dengan variasi temperature adsorber dan evaporator (30°C, 35°C, 40°C). Didapatkan bahwa densitas energi paling besar didapatkan pada temperature 40°C sebesar 69.65 kWh/m3. Terlebih lagi, zeolite alam dapat terus dikembangkan untuk meningkatkan kemampuannya mengadsorp air dan menyimpan panas lebih banyak.

Adsorption thermal energy storage has reversible reaction which are exothermic in adsorption reaction and endothermic in desorption reaction. This system is a promising technology for the storage of intermittent energy, such as solar power and industrial waste heat. During the adsorption reaction, heats are released and calculated as the amount of energy that can be stored. Natural zeolite is a potential adsorbent due to its high heat of adsorption, porous structure, high surface area and ability to adsorb small molecule such as water. Moreover, Indonesia has quite a lot of zeolite resourches. In this research, we analyze the storage performance of adsorption thermal energy storage using natural zeolite-water as a pair for charging temperature of 160°C at different evaporator and adsorber temperature ranges (30°C, 35°C, 40°C). As the result, the highest energy density reached at temperature 40°C with 69.65 kWh/m3. Furthermore, natural zeolite can be developed as it can be modified to enhance its ability to adsorb water.
"
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>