Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 67451 dokumen yang sesuai dengan query
cover
"laminating technology is combining two or more of the same material or different mechanical properties and fisis. The method used is laminated horizontally laminated bending test (bending) where the size and shape to follow the rules of press ASTM test specimens (ASTM D 143)...."
Artikel Jurnal  Universitas Indonesia Library
cover
Ahmedi Asraf
"ABSTRAK
Interaksi yang kompleks antar lamina pada suatu laminat saat mengalami beban tarik menyebabkan perbedaan kuat tarik dan jenis kerusakan pada komposit laminat karbon/epoksi dengan susunan lamina yang berbeda. Untuk mengetahui pengaruh susunan lamina terhadap kuat tarik dan jenis kerusakan komposit laminat, 5 komposit laminat dibuat dengan metode hand lay up dengan susunan (0)5, (0/0/90)s, (0/45/-45/901/2)s, (0/45/-45/90)s dan (0/90/-45/45)s. Hasil uji tarik menunjukkan kuat tarik dari komposit laminat (0)5, (0/0/90)s, (0/45/-45/901/2)s, (0/45/-45/90)s dan (0/90/-45/45)s secara berturut-turut adalah ( 1988,97 ± 156,69 ) MPa, ( 1745,47 ± 19,53 ) MPa, ( 929,70 ± 32,79 ) MPa, ( 992,82 ± 26,63 ) MPa dan ( 941,86 ± 24,21 ) MPa. Hasil pengamatan dengan mikroskop optik pada bagian pinggir komposit laminat menunjukkan bahwa kerusakan yang terjadi pada setiap komposit laminat adalah delaminasi, retak mikro matriks dan perpatahan serat.

ABSTRAK
A complex interaction between lamina in laminate composites when receive an applied load causes different tensile strength values and types of damage on the carbon/epoxy laminate composites with different lamina stacking sequence. To know the effect of lamina stacking sequence on tensile strength value and the types of damage, five types of laminate composites were made by hand lay up method where the stacking sequence were (0)5, (0/0/90)s, (0/45/- 45/901/2)s, (0/45/-45/90)s dan (0/90/-45/45)s. The test results showed that the tensile strength value of the (0)5, (0/0/90)s, (0/45/-45/901/2)s, (0/45/-45/90)s and (0/90/-45/45)s laminates are ( 1988,97 ± 156,69 ) MPa, ( 1745,47 ± 19,53 ) MPa, ( 929,70 ± 32,79 ) MPa, ( 992,82 ± 26,63 ) MPa and ( 941,86 ± 24,21 ) MPa respectively. An observation with optical micrograph at the edge of laminate composites showed that the type of damages that occured on that laminates were delamination, matrix microcracking and fiber breakag"
2016
S64974
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rizky Hidayanto
"ABSTRAK
Bagan atau bagang merupakan alat perangkap ikan dan hasil tangkapan lainnya yang dioperasikan oleh nelayan secara pasif di malam hari yang menggunakan lampu sebagai pemikat untuk ikan-ikan tersebut. Bagan yang sering dijumpai khususnya di wilayah pesisir laut Jakarta biasanya dibuat dari bambu yang dirakit-rakit sedemikian rupa menyerupai perkemahan di atas air. Penyangga dari bangunan tersebut hanya berupa bambu-bambu yang disambung-sambung dan ditancapkan begitu saja di dasar laut berkedalaman 15 sampai 30 meter. Apabila dilihat dari aspek keselamatan pekerja di bagan tersebut terlihat sangat meragukan. Maka diperlukan suatu rancangan model bagan yang dipandang dari sisi keselamatan untuk pekerjanya lebih terjamin. Adapun kayu, kebutuhannya semakin meningkat seiring berjalannya waktu. Sehingga berdampak buruk terhadap persediaan kayu di Indonesia. Sementara bambu, dapat dipanen lebih cepat daripada kayu dan persediannya juga sangat melimpah. Selain itu bambu dapat dilaminasi yang menurut studi literatur sifat-sifatnya dapat mengungguli kayu. Oleh karena itu dipilih bambu laminasi sebagai bahan utama rancangan bagan. Fokus utama pembahasan pada skripsi ini ialah membahas tentang perancangan bagan yang sesuai dengan kriteria tersebut. Besar harapan juga rancangan ini dapat dimanfaatkan sebesar-besarnya oleh nelayan.

ABSTRACT
Bagan or bagang is a fish trap and other catches provided by fishermen at night that use lights as a decoy for these fish. Bagan that are often found in the coastal areas of Jakarta are usually made from bamboo which is assembled to be adapted to the air. The buffer of the building consists only of bamboos that are joined together and plugged in on the seabed with a depth of 15 to 30 meters. When viewed from the aspect of worker safety in that bagan looks very doubtful. So we need a design of bagan model that is seen from the safety side for workers who are more secure. As for wood, its needs have increased over time so that it has a negative impact on wood supplies in Indonesia. While bamboo, can be harvested faster than wood and the supply is also very abundant. Besides bamboo can be laminated which, according to the study of literature, its properties can outperform wood. Therefore laminated bamboo was chosen as the main material for the bagan design. The main focus of this essay is to discuss the design of bagan that meet these criteria. It is also hoped that this design can be utilized maximally by fishermen.
"
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Youssef Benbouras
"The use of composite materials with continuous fibers in the aircraft and aerospace industries requires a thorough knowledge of behaviors of these laminate composites under various loading conditions. Indeed, the aim of this work is to simulate linear and nonlinear behavior of a symmetric laminated composite under three-point bending tests. The modelization used is based on an analytical approximation that has been recently developed for isotropic materials. This approximation is still valid for the studied quasi-isotropic laminated composite because it is symmetric with a specific layer sequence. The overall response of laminate composite is determined from the behavior of each ply outside of their orthotropic axis. Two methods are used to calculate the equivalent longitudinal Young-modulus of the laminate. The result shows that when the deflection of the specimens is less than 2.5 times the thickness, the difference between the experimental and analytical curves is about 1% for the average global stresses method, and about 7.5% for the apparent bending modulus method. For large deflections, the difference relative to the first method remains less than 11% and the second method is about 20%."
Depok: Faculty of Engineering, Universitas Indonesia, 2017
UI-IJTECH 8:3 (2017)
Artikel Jurnal  Universitas Indonesia Library
cover
Adinda Oktaviani
"Perkembangan teknologi pada dunia militer sedang berkembang pesat, salah satunya adalah material baru untuk aplikasi kendaraan tempur dimana merupakan sebuah komposit laminat. Komposit ini terbuat dari lembaran logam AA7075 dan kevlar yang ditambahkan epoksi resin. Setelah dilakukan penambahan serbuk nano TiC dilakukan pengujian untuk mengetahui kemampuannya untuk menyerap energi balistik dari proyektil. Terbentuknya Solid Thickening Fluid (STF) yaitu dengan mencampurkan serbuk nano TiC dengan PEG-400, menggunakan magnetic stirrer selama 2 jam, yang nantinya akan diimpregnasikan ke lapisan kevlar. Langkah selanjutnya ialah membuat struktur komposit laminat dengan metode hand layup dilanjutkan dengan proses pengeringan di temperatur ruang. Setelah itu, Daya serap energi dari komposit yang diimpregnasi oleh STF nantinya akan dibandingkan dengan komposit tanpa impregnasi dengan variasi jumlah lapisan sebanyak 8, 16, dan 24 lapisan kevlar. Selain itu, komposit dilakukan pengujian SEM untuk melihat persebaran serbuk nano keramik pada kevlar serta pengujian foto makro untuk mengetahui jenis kegagalan setelah pengujian balistik. Hasil penelitian dari penambahan TiC dan penambahan jumlah lapisan kevlar pada sampel menunjukkan hasil yang baik pada pengujian balistik dan impak.

Technological developments in the military world are growing rapidly, one of which is a new material for combat vehicle applications which is a laminated composite. This composite is made of AA7075 sheet metal and kevlar with added epoxy resin. After adding TiC nanopowder, a test was carried out to determine its ability to absorb ballistic energy from projectiles. Solid Thickening Fluid (STF) is formed by mixing TiC nano powder with PEG-400, using a magnetic stirrer for 2 hours, which will later be impregnated onto a kevlar layer. The next step is to make a laminate composite structure with the hand layup method followed by a drying process at room temperature. After that, the energy absorption of composites impregnated by STF will be compared with composites without impregnation with variations in the number of layers of 8, 16, and 24 layers of kevlar. the results of the addition of TiC and the addition of the number of layers of Kevlar on the sample showed good results in ballistic and impact testing."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Regita Anggriyani
"Dalam berbagai jenis konstnxksi, banyak sekali digunakan struktur beton bertulang.. disamping keuntungan dalam pemakaian beton bertulang, salah satunya adalah karena pembangunan struktur beton bertulang lebih mudah dalam pelaksanaanya. Namun pada kenyataannya di Iapangan, tak sedikit kerusakan yang terjadi pada stuktur beton bertuiang. Kerusakan tersebut dapat disebabkan oleh banyak hal, diantaranya adalah kerusakan yang disebabkan oleh pengaruh Esika, mekanika, dan kimia.
Pembahasan pada skripsi ini mengambil fokus kerusakan akibat pembebanan berlebih (overload). Untuk menangani kerusakan tersebut akan dilakukan perbaikan struktur beton bertulang dengan menggunakan bahan perbaikan concresive1438, Injection Resin LPL sebagai bahan perbaikan, dan M-Brace Laminate sebagai bahan perkuatan Perbaikan yang akan dilakukan adalah dengan metode injeksi dan perekatan bahan perkuatan pada sisi bawah balok.
Penelitian yang akan dilakukan, selain didasarkan pada studi literatur, juga dilakukan simulasi perbaikan balok dengan melakukan perbaikan modul balok yang telah runtuh diikuti dengan pengujian guna mendapatkan kinerja dan kapasitas dari balok perbaikan tersebut. Hasil dari penelitian minimal hams sama dengan perilaku balok beton utuh.
Simulasi dan pengujian yang telah dilakukan menunjukkan bahwa balok yang mengalami perbaikan dengan material concresivel438, Injection Resin LPL, dan M-Brace Laminate, memiliki I-cinerja yang baik apabila digunakan secara bersamaan. Sehingga dapat digunakan pada pekerjaan perbaikan kerusakan struktur akibat pembebanan berlebih.

In many kind of construction, lots of themuse reinforced concrete structure. One of the benefits of using reinforced concrete is it has high workability. Nevertheless in reality, damage in reinforced concrete did happened. The damage could be cause by lots of factors, some of them caused by physical, mechanical? and chemical affection.
The study in this thesis lakes focus on damage caused by overloading. To handle the damage, a reparation will be taken using Concresive 1438 and Injection Resin LPL as repairing material, and M-Brace Laminate as strengthening material.The reparation will be done using the injection method and bonding tl1e strengthening material at the bottomside of the beam.
The study taken not only based on literally study, but also on beam repairing simulation, by conducting reparation on beam modul, which has been failure, followed by test to get the ability and cappacity of the repaired beam. The result of the study must have the minimun strength as the normal beam.
The smulation and test that have been conducted, shows tat the beamthat have been repaired with Concresive 1438, Injection Resin LPL, and M-Brace Laminate material has better results. So the repairing method can be used to repair damage on reinforced concrete structure caused by overloading."
Depok: Universitas Indonesia, 2006
S35238
UI - Skripsi Membership  Universitas Indonesia Library
cover
Luthfiah Farah Az-Zahra
"Industri pertahanan nasional khususnya kendaraan tempur membutuhkan adanya pengembangan dari sisi material untuk meningkatkan efektivitas dalam menahan serangan proyektil serta mempermudah mobilitas saat digunakan di medan perang. Pada penelitian ini, digunakan komposit laminat dengan matriks berupa plat aluminium AA5052 dan serat kevlar dengan variasi jumlah lapisan sebanyak 20, 30, dan 40 layer. Kevlar di dalam komposit laminat ini diimpregnasikan dengan campuran nanopartikel SiC (Silikon Karbida) 50nm, ethanol, dan PEG-400 sebagai Shear Thickening Fluid (STF). Plat aluminium dan kevlar direkatkan menggunakan resin epoksi dan hardener dengan metode hand lay-up. Untuk mengetahui ketahanan balistik dan sifat mekanis, dilakukan pengujian balistik level III dan IV yang kemudian dianalisis kedalaman penetrasi proyektil dan diameter perforasi dari komposit laminat. Analisis mikrostruktur dan kandungan unsur dari komposit laminat dilakukan dengan Scanning Electron Microscopy (SEM), Energy Disperse X-Ray Spectrometry (EDS), dan Fourier Transfer Infrared Spectrometry (FTIR). Hasil penelitian menunjukkan adanya pengaruh pada ketahanan balistik dan kekuatan mekanis akibat pengimpregnasian nanopartikel SiC dan variasi jumlah kevlar yang digunakan pada komposit laminat.

The national defense industry, especially combat vehicles, requires materials development to increase effectiveness in ballistic resistant and mobility when used on the battlefield. In this study, laminated composites with a matrix of AA5052 aluminum plate and kevlar fiber were used with variations in the number of layers of 20, 30, and 40 layers. The kevlar fabric in this laminated composite was impregnated with a mixture of 50nm SiC (Silicon Carbide) nanoparticles, ethanol, and polyethylene glycol (PEG-400) as Shear Thickening Fluid (STF). The aluminum and kevlar plates are glued together using epoxy resin and hardener by the hand lay-up method. To determine the ballistic resistance and mechanical properties, level III and IV ballistic tests were carried out followed by analyzing the projectile penetration depth and perforation diameter of the laminated composite. Analysis of the microstructure and elemental content of the laminated composites was carried out by Scanning Electron Microscopy (SEM), Energy Disperse X-Ray Spectrometry (EDS), and Fourier Transfer Infrared Spectrometry (FTIR). The results showed that there was an effect on ballistic resistance and mechanical strength due to the impregnation of SiC nanoparticles and variations in the amount of Kevlar used in laminated composites."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Agung Pascal Sampeliling
"Pengembangan tank sebagai kendaraan tempur saat ini terus dilakukan untuk meningkatkan kekuatan militer suatu negara. Salah satu komponen utama pada tank adalah material armor. Penggunaan aluminium dan serat kevlar yang kemudian disusun menjadi material komposit laminat memiliki massa jenis yang jauh lebih rendah dari baja, namun memiliki kekuatan impak yang tinggi, sehingga diharapkan dapat menggantikan peran baja pada tank sebagai material armor. Pada penelitian ini, untuk membuat material komposit laminat hybrid digunakan AA 5052 sebagai matriks dan kevlar yang diimpregnasi dengan nano aluminium oksida sebagai penguatnya. Terdapat 3 variasi jumlah lapisan kevlar yang dilakukan dalam penelitian ini, yaitu 20, 30, dan 40 lapisan yang disusun tiga tingkat dalam satu sampel komposit laminat hybrid. Semakin tebal lapisan kevlar, semakin besar nilai kekuatan impak komposit laminat hybrid. Pada sampel terimpregnasi, hasil pengujian balistik dengan NIJ standard 0108.01 yang dilakukan menunjukkan sampel dengan 20 lapisan kevlar dapat tahan uji balistik level 3, sedangkan sampel dengan 30 lapisan kevlar dapat tahan uji balistik level 4.

The development of tank as a combat vehicle is currently being carried out to increase the military strength of a country. One of the main components of the tank is the armor material. Aluminum and kevlar fiber which is then arranged into a laminated composite material has a lower density than a steel, but has a high impact strength, so it is expected to replace the role of steel in tanks as armor material. In this study, to make a hybrid laminate composite material, aluminum alloy 5052 was used as a matrix, and kevlar impregnated with nano aluminum oxide as reinforcement. There are 3 variations in the number of kevlar layers carried out in this study (20, 30, and 40 layers). Each of the type will be arranged in three tiers in one sample of hybrid laminate composite. The thicker the kevlar layer, the greater the value of the impact strength of the hybrid laminate composite. For the impregnated sample, the results of the ballistic test with NIJ standard 0108.01 that were carried out showed that the sample with 20 layers of kevlar could withstand the level 3 ballistic test, while the sample with 30 layers of kevlar could withstand the level 4."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ahmmad Muttaqien Trisyarahman
"Kayu, dengan sifat serta tekstur dan warna yang dimilikinya menjadikannya banyak digunakan dalam sektor bangunan arsitektural. Sifat dari material kayu yang terasa hangat dan sedap dipandang mata dimanfaatkan sebagai material untuk finishing estetis. Pengolahan kayu menjadi elemen bangunan sudah dimulai sejak lama dan saat ini juga sering kita temui, terutama pada elemen kusen pintu dan jendela.
Kondisi hutan sebagai sumber penghasil kayu saat ini sudah semakin memprihatinkan. Keadaan ini akan berdampak pada kerusakan alam, yang berujung pada bencana alam yang merugikan menimpa manusia. Oleh karena itu sudah seharusnya kita mulai menggunakan material alternatif dari kayu agar mengurangi penjarahan hutan kayu sehingga hal ini tidak mengancam kehidupan kita di kemudian hari.
Seiring dengan berkembangnya ilmu pengetahuan dan teknologi di bidang science, ditemukan material yang disebut polyvinyl chloride (PVC). PVC adalah sejenis bahan plastik, yang didapat dari hasil reaksi kimia dengan bahan utama gas alam. Secara fisik material PVC bersifat tidak memuai dan susut, tidak berubah (melengkung, bergelombang) karena perubahan cuaca, tidak mudah retak, warnanya tidak pudar dan selain itu juga tahan air, anti rayap, aman dari gangguan korosi, dan mudah dibersihkan.
Aplikasi kusen pintu dan jendela, sudah mutlak diperlukan dalam fisik bangunan. Material PVC jenis Unplasticized atau disebut PVC-U sudah mulai digunakan sebagai kusen pintu dan jendela. Sifat dari material ini yang banyak lebih menguntungkan dibandingkan dengan kayu, menjadikannya layak untuk dijadikan sebagai pengganti kayu. Dengan digunakannya PVC-U sebagai material alternatif dari kayu diharapkan dapat mengurangi penggunaan kayu dalam bangunan, sehingga kondisi alam akan menjadi kembali seimbang dan terhindar dari bencana alam.

Wood, with it?s properties on texture and colour, become widely used in architecture. The properties of wood which feel warm and beautiful to see, made it is worth to used as finishing material. The processing of wood as building material was started since long time ago and we also can easily meet nowadays, specifically as doors and windows.
Today, the condition of forest as wood source has become worse. This situation will affect on damage of nature and then cause a disaster that impact on human being. Since that, it is important for us to start using alternative material anything bad happen to us on the next day.
Together with science and technology growth, they have found new material named polyvinyl chloride (PVC). PVC is a plastic material, which gained from chemical reaction, contained natural gas at most. Physically, PVC material not expanded or shrink, not change (arched, waved) caused by weather changes, hard to crack, the colour not faded and also water resistant, termite resistant, safe from corrosion, and easy to clean.
Doors and windows frame application is absolutely needed in a building. Unplasticized PVC material, called PVC-U, was being used as doors and windows frame application. The characteristics of this material which has much more benefit than wood itself have made it reasonable to become wood replacement. Started using PVC-U as alternative material from wood, hopefully could reduced wood usage in building, so that nature condition will become more stable and avoided from natural disaster.
"
2008
S48418
UI - Skripsi Open  Universitas Indonesia Library
cover
Muhammad Fadlilah
"Komposit merupakan material yang sedang dikembangkan, yang terdiri dari dua jenis material atau lebih untuk meningkatkan sifat mekanis. Salah satu aplikasinya yaitu pada tabung roket, yang menggunakan komposit berbahan dasar logam Metal Matrix Composite . Material yang digunakan yaitu Al 6061 dengan penambahan partikel nano SiC 0.15 Vf sebagai penguat, Mg 10 wt. sebagai agen pembasah, dan variabel TiB sebesar 0.02, 0.03, 0.04, 0.05, dan 0.06 wt. sebagai pemodifikasi butir agar lebih halus dan meningkatkan sifat mekanis. Hasil dari penelitian ini menunjukan dengan adanya penambahan partikel nano SiC dan TiB sebagai pemodifikasi ukuran butir, dapat meningkatkan sifat mekanis. Penambahan TiB yang paling baik yaitu pada pada penambahan 0.06 wt. dengan kandungan aktual pada komposit sebesar 0.0535 wt. , yang menghasilkan nilai kekuatan tarik sebesar 204.9 MPa, nilai kekerasan 53.58 HRB, dan laju keausan sebesar 0.0012 mm3/m. Peningkatan sifat mekanis disebabkan karena terdapat fasa Mg2Si sebagai penguat, lalu TiB2 sebagai agen nuklean yang memperhalus butir, dan fasa MgAl2O4 yang berada pada antarmuka partikel nano SiC dengan matriks sehingga memiliki pembasahan yang baik.
Composite is advance material that being developed, that contains of two materials or more to improve the mechanical properties. One of the application is rocket tube, that using metal matrix composite MMC . The base material is Al 6061 with addition of nanoparticles SiC 0.15 Vf as reinforcment, Mg 10 wt. as wetting agent, and variables of TiB 0.02, 0.03, 0.04, 0.05, and 0.06 wt. as grain refiner so it can improve the mechanical properties too. The result of this research, that with addition of nanoparticles SiC and TiB as grain refiner, it make the improvement of mechanical properties. The best addition of TiB is with the addition of 0.06 wt. TiB, which is the actual content in composite is 0.0535 wt. . The result shows that the Ultimate Tensile Strength reached 204.9 MPa, the hardness is 53.58 HRB, and the wear rate is 0.0012 mm3 m. The improvement of mechanical properties are because of there are Mg2Si phase as second phase that increase the strength of material, TiB2 as the nuclean to refine the grain, and MgAl2O4 phase that exist in the interface of nanoparticles SiC and the matrix, so it have good wettability between nanoparticles SiC and the matrix."
2016
S66212
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>