Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 116602 dokumen yang sesuai dengan query
cover
Arief Randy Wicaksono
"Sistem pendinginan konvesional pada piranti elektronik dengan menggunakan fan sudah tidak efektif dan memadai untuk diaplikasikan sekarang ini. Miniaturisasi produk dengan performa kinerja yang semakin canggih menyebabkan diperlukannya sistem pendingin baru yang mempunyai efisiensi termal yang tinggi dan juga hemat energi. Jet sintetik dapat dijadikan sistem pendinginan baru berdasar input massa netto nol tetapi momentum tidak nol. Dalam penelitian ini dua buah membran jet sintetik dengan tipe aliran silang (Cross-Flow) diuji dan dianalisa untuk membandingkan karakteristik efek pendinginan yang masing-masing membran digetarkan dengan menggunakan variasi gelombang sinusoidal dan square. Penelitian dilakukan dengan menggunakan metode komputasi dan eksperimental. Pada tahap komputasional penelitian ini menggunakan software CFD Fluent dengan model turbulensi k-w SST dengan elemen meshing Quad tipe Pave. Pada tahapan eksperimen, digunakan 2 function generator untuk menggerakkan membran dengan menggunakan variasi fungsi frekuensi Sinusoidal dan Square untuk 5 prototype uji pada masing-masing percobaan serta tiga frekuensi osilasi yaitu 80 Hz, 120 Hz, dan 160 Hz serta heat flux konstan 10 W/m2,25 W/m2, dan 50 W/m2 pada amplitudo tetap 0.002 m/s. Penelitian menggunakan jet sintetik ber-tipe aliran silang bertujuan untuk memperbaiki serta mengoptimumkan proses pendinginan jet sintetik akibat adanya confinement effect atau efek sekam dimana panas yang dibuang akan terakumulasi kembali pada cavity dari jet sintetik sehingga pendinginan pada heatsink terhenti. Pada riset kali ini akan dilihat seberapa lama waktu optimum pendinginan jet sintetik ber-tipe aliran silang serta frekuensi osilasi ter-optimum dalam proses pendinginan heat sink.

Current advancement of micro electronic devices have made the conventional fan-based cooling is no longer effective and applicable. Miniaturization with higher performance of electronic products causes the need for a new cooling system that has high thermal efficiency and low energy consumption. Synthetic jet which is based on zero netto mass input but non zero momentum is a new approach utilized for cooling system. The synthetic air jet was generated by vibrating membranes which pushed out the air from the cavity through the exit nozzles with oscillatory motion. The main purpose of this synthetic jet was to create vortices pair to come out from nozzle which will accelerate the heat transfer process occurring at the heat sink. This research investigated the forced cooling characterization of a cross flow synthetic jet using double membrane actuator with two different variations of sinusoidal and square wave and was conducted both in computational as well as also experimental stage. Computational stage was conducted by a commercial CFD software of Fluent® with a turbulence model k- ω SST with meshing elements quad type pave, while in the experimental work the function generators was used to drive the membranes with the variation of sinusoidal and square wave in three oscillation frequencies i.e 80 Hz, 120 Hz, and 160 Hz at fixed amplitude of 0.002 m/s for condition of constant heat flux for 10 W/m2,25 W/m2, dan 50 W/m2. The main purpose of this research is to improve and optimizing the process of synthetic jet cooling by suppressing the confinement effect. The confinement effect phenomena, which commonly occurs an impinging synthetic jet flow, causes the hot air is sucked back and will accumulate into the cavity of synthetic jet actuator and will reduce the cooling effect. The experimental results show significant effect of the reduction of the confinement effect phenomena by using the cross flow synthetic jet. The best heat transfer rate hence the optimum cooling effect was obtained at a lower oscillation frequency; in this study at sinusoidal 120 Hz - square 80 Hz.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
T34951
UI - Tesis Membership  Universitas Indonesia Library
cover
Aldy Andika
"Seiring dengan cepatnya kemajuan teknologi dalam industri elektronik, muncul banyak produk baru yang semakin kecil. Kondisi ini menimbulkan tantangan baru, yaitu kebutuhan akan sistem pendinginan berdimensi kecil dan hemat energi namun memiliki efisiensi termal yang tinggi, dimana jet sintetik dengan input massa nol dan output momentum tidak nol hadir sebagai sistem pendingin yang menjanjikan. Penelitian ini membahas karakteristik perpindahan panas oleh jet sintetik bertipe aliran silang dan dilakukan dalam dua tahap, yaitu tahap komputasi dan eksperimental. Tahap eksperimental dilakukan menggunakan function generator untuk menggerakkan membran dua buah membran dengan mengirimkan variasi fungsi sinusoidal dan segiempat dengan frekuensi osilasi sin 80 Hz - square 80 Hz, sin 80 Hz - square 120 Hz, sin 80 Hz - square 160 Hz, sin 120 Hz - square 80 Hz, sin 120 Hz - square 120 Hz, sin 120 Hz - square 160 Hz, sin 160 Hz - square 80 Hz, sin 160 Hz - square 120 Hz, sin 160 Hz - square 160 Hz untuk melihat karakteristik perpindahan panas konvektif pada heat sink. Tahap komputasi dilakukan menggunakan software CFD Fluent dengan model turbulensi k-ω SST dengan tipe meshing Tet/Hybrid Tgrid untuk melihat distribusi aliran dari jet sintetik aliran silang. Hasil penelitian menunjukkan pengaruh gelombang dan frekuensi getaran membran terhadap laju perpindahan panas yang didapat pada jet sinjetik bertipe aliran silang, dengan penurunan terbesar dicapai variasi gelombang sin 120 Hz - square 80 Hz.

Along with rapid technological advances in the electronics industry, there are many new emerging advanced products which getting smaller in dimension with high space efficiency and work relying on components such as transistors and integrated circuit (IC). However, these conditions also cause new challenges to overcome, one of which is how to cope with the heat generated by the operation of the electronic components in the product with sophisticated cooling system. The cooling system, hence, needs less space and energy consumption but has high thermal efficiency. This is why the synthetic jet with zero net mass flux and non-zero net momentum flux sounds practicable as the new cooling system. This research will discuss the characteristics of flow and convective heat transfer in the cross-flow synthetic jet that was conducted in two stages, computational and experimental stage.The experimental stage was executed using the function generators to drive the upper and lower membranes by sending functions of sinusoidal and square frequency variations with multiple oscillation frequency of sin 80 Hz - square 80 Hz, sin 80 Hz - square 120 Hz, sin 80 Hz - square 160 Hz, sin 120 Hz - square 80 Hz, sin 120 Hz - square 120 Hz, sin 120 Hz - square 160 Hz, sin 160 Hz - square 80 Hz, sin 160 Hz - square 120 Hz, sin 160 Hz - square 160 Hzto see the characteristics of convective heat transfer on the heat sink at each trial. Computational stage was conducted by Fluent CFD software with k-ω SST turbulence model with Tet / Hybrid Tgrid meshing elements type to see the flow distribution of creoss-flow synthetic jet. The results showed the significant influence of waves mode and frequencies to the heat transfer rate of cross-flow synthetic jet, with the best result is on sin 120 Hz- square 80 Hz waves."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S44938
UI - Skripsi Membership  Universitas Indonesia Library
cover
Situngkir, Christoforus Deberland
"Dewasa ini, beban panas yang semakin besar akibat meningkatnya kecepatan operasi
dan densitas komponen pada suatu piranti elektronik menyebabkan perlunya sistem
pendingin baru yang lebih efisien atau mempunyai disipasi panas yang tinggi. Jet
sintetik potensial untuk digunakan sebagai pendingin komponen elektronik. Paper ini
melaporkan hasil dari studi eksperimental mengenai pengaruh Jarak Tumbukan
(impinging distance) pada performa pendinginan dengan tumbukan jet sintetik. Rasio
jarak aksial antara permukaan yang dipanaskan dan jet (L) terhadap diameter orifis jet
(d) berada pada jangkauan 0-3.3. Investigasi dilakukan dengan menggunakan
prototipe jet sintetik yang memiliki 16 lubang dengan diameter tiap lubang 3 mm dan
digerakkan oleh dua membran piezoelektrik 5 volt dengan eksitasi gelombang
sinusoidal. Dengan sistem aparatus tersebut diteliti karakteristik dari perpindahan
panas konvektif yang dihasilkan membran yang berosilasi. Hasil penelitian
menunjukkan adanya pengaruh ketinggian orifis yang signifikan terhadap laju
perpindahan panas yang didapat. Pada frekuensi eksitasi tinggi 160 Hz, kenaikkan
nilai perpindahan sebanding dengan kenaikkan rasio L/d hingga nilai L/d sebesar 2
kemudian turun hingga L/d sebesar 3,3.

Nowadays, A greater heat load due to miniaturization of electronic products causes
the need for a new cooling system that works more efficient and has a high thermal
efficiency, Synthetic jet is potentially useful for cooling of electronic components. In
this study, numerical simulations are performed to investigate the effect of various
the distance between the orifice and the heated surface (L) on the ensuing synthetic
jet flow. In this research the investigation was carried out by comtutational methods
using the software CFD (Computational Fluid Dynamics), it will be seen the
characteristics of convective heat transfer by moving the synthetic jet membrane. A
circular orifice synthetic jet is simulated assuming axisymmetric behaviour. The
quality of results is verified by time and convective heat transfer studies, and the
results are validated against existing experimental. In this research the model was
simulated to examine the distribution of heat flow on the walls using a mathematical
turbulen model k-w SST. Meshing order was elements Tet/Hybrid and type Tgrid.
The boundary conditions were inlet velocity of 1.5 m/s, 2 m/s and 1 m/s, the
frequency of membrane vibration were 80 Hz, 120 Hz, 160 Hz and the amplitude
were 1 mm/s, 2 mm/s, 1.5 mm/s. The Reynolds number (Re) is in the range of 1421 –
2843 based on average velocity, while the normalized axial distance varies between 0
and 3.3. The movement of the piezo membrane is assumed of sinusoidal motion
which moves up and down correspond to the suction and blowing phase respectively.
The results showed the significant influence of L/D Ratio and sinusoidal wave
frequencies to the heat transfer rate that obtained. At small axial distance (L),
recirculation of fluid occurs due to confinement, owing to the presence of the orifice
plate. However, at large axial distances, the jet velocity reduces due to entrainment of
still ambient air, which again reduces the heat transfer coefficient.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
T35771
UI - Tesis Membership  Universitas Indonesia Library
cover
Rikko Defriadi
"Sejalan dengan perkembangan peradaban, kehidupan manusia tidak bisa terlepas dari berbagai peralatan elektronika yang memiliki banyak sekali komponen seperti: transistor, kapasitor, resistor, dll. Komponen elektronik ini memancarkan panas sewaktu mereka beroperasi, sehingga untuk mengatasi masalah ini, diperlukan suatu sistem pendinginan yang efektif. Kebanyakan dari system pendinginan komponen elektronika yang dipakai sekarang ini berbasis pada fan. Namun sistem ini semakin tidak memadai dengan perkembangan teknologi elektronika yang semakin mengarah pada miniaturisasi produk. Sebagai alternatif pengganti sistem berbasis fan ini, manusia mengembangkan suatu alat yang disebut jet sintetik. Jet sintetik memiliki dimensi yang relatif kecil, tingkat kebisingan yang lebih kecil, lebih sedikit memancarkan panas dan yang paling penting jet sintetik memiliki efisiensi pendinginan yang lebih besar dibanding fan.
Thesis ini membahas hasil penelitian yang dilakukan terhadap 4 prototype desain original jet sintetik dengan menggunakan kombinasi pendekatan komputasi dan eksperimen. Tahap komputasional pada penelitian ini dilakukan dengan menggunakan software CFD Fluent dengan model turbulensi k-ω SST dengan elemen meshing Tet/Hybrid tipe Tgrid untuk melihat distribusi aliran pada jet sintetik. Sedangkan pada tahap eksperimental akan dipelajari karakteristik perpindahan panas konveksi dengan variasi jenis gelombang sinusoidal, triangle dan square pada frekuensi 80 Hz, 120 Hz dan160 Hz.

In line with the development of civilization, human life can not be separated from a various electronic equipment that has many components such as transistors, capacitors, resistors, etc. These electronic components emits heat when they operate, an effective cooling system is required in order to overcome this problem. Most of the electronic component cooling systems used today are based on the fan. But this system is inadequate to the development of electronics technology that increasingly lead to the product miniaturization. As an alternative to this fan-based system, humans developed a device called synthetic jet. Synthetic jets have relatively small dimensions, smaller noise level, emits less heat and the most important that synthetic jet has a greater cooling efficiency than fan.
This thesis discusses the results of research conducted on four original designed synthetic jet prototype using a combination of computational and experimental approaches. Computational phase was conducted using Fluent CFD software with k-ω SST turbulence model with meshing elements of the Tet / Hybrid type Tgrid to see the flow distribution in the synthetic jet. While the experimental phase will be studied at the convective heat transfer characteristics with variations in type of sinusoidal wave, triangle and square at a frequency of 80 Hz, 120 Hz dan160 Hz.
"
Depok: Fakultas Teknik Universitas Indonesia, 2012
T30054
UI - Tesis Open  Universitas Indonesia Library
cover
Yudha Syafei Agustian
"ABSTRAK
Penelitian ini membahas tentang perbandingan koefisien perpindahan kalor aliran
dua fasa dari hasil percobaan dengan hasil prediksi dari korelasi yang terdapat
pada literatur. Percobaan dilakukan pada kondisi perpindahan panas konveksi
didih pada kanal mini horizontal dengan refrigeran R-22. Test section terbuat dari
pipa stainless steel dengan diameter dalam 3 mm, panjang 1000 mm dan
dipanaskan secara merata di sepanjang pipa tersebut dengan heat flux divariasikan
antara 5 kW/m2 sampai dengan 15 kW/m2. Dalam penelitian ini menggunakan
korelasi Chen (1963), korelasi Gungor-Winterton (1986) dan korelsi Zhang et al.
(2004). Selanjutnya koefisien perpindahan kalor dari tiap korelasi dihitung dan
dibandingkan mean deviation dan average deviation-nya terhadap hasil percobaan
untuk mengetahui penyimpangan pada setiap korelasi. Koefisien perpindahan
kalor yang diperoleh dengan menggunakan korelasi Chen memiliki mean dan
average deviaion lebih rendah dibandingkan dengan korelasi lain. Nilai koefisien
perpindahan kalor dipengaruhi oleh heat flux yang diberikan, dimana semakin
besar heat flux yang diberikan maka semakin besar pula nilai koefisien
perpindahan kalornya.

ABSTRACT
This study discusses the comparison of two phase flow heat transfer coefficient of
the experimental results with predicted results from the correlation found in the
literature. Experiments were performed on the convective boiling heat transfer in
horizontal minichannel with R-22. The test section was made of stainless steel
tube with inner diameter of 3 mm, length of 1000 mm and it is uniformly heated
along the tube with heat flux was varied from 5 kW/m2 up to 15 kW/m2. In this
studi using Chen?s correlation (1963), Gungor-Winterton?s correlation (1986) and
Zhang?s correlation (2004). Furthermore, the heat transfer coefficient from each
correlation was calculated and compared with the mean deviation and average
deviation of the experimental results to determine deviations in each correlations.
Heat transfer coefficients obtained by using Chen?s correlation has a mean and
average deviation lower than other correlations. The value of heat transfer
coefficient is affected by the heat flux was given, where the higher value of heat
flux given will result the higher value of heat transfer coefficient."
Fakultas Teknik Universitas Indonesia, 2011
S1798
UI - Skripsi Open  Universitas Indonesia Library
cover
Arief Randy Wicaksono
"ABSTRAK
Sistem pendinginan konvesional dengan menggunakan fan dianggap
sudah tidak lagi efektif dan memadai untuk diaplikasikan dewasa ini.
Miniaturisasi produk dengan performa kinerja yang semakin canggih
menyebabkan diperlukannya sistem pendingin baru yang mempunyai efisiensi termal yang tinggi dan juga hemat energi. Synthetic jet dapat dijadikan sistem pendinginan baru berdasar input massa netto nol tetapi momentum tidak nol.
Dalam penelitian ini dua buah membran jet sintetik dengan tipe aliran impinging akan digetarkan dengan menggunakan variasi gelombang sinusoidal dan square. Penelitian akan dilakukan dengan menggunakan komputasional dan eksperimental. Pada tahap komputasional penelitian ini menggunakan software CFD Fluent dengan model turbulensi k-w SST dengan elemen meshing Tet/Hybrid tipe
Tgrid, sedangkan pada tahap eksperimental menggunakan function generator untuk menggerakkan membran dengan menggunakan fungsi variasi Sinusoidal dan Square serta tiga frekuensi osilasi yaitu 80 hz, 120 hz, dan 160 hz pada amplitudo tetap 1 m/s. Hasil eksperimen menunjukkan adanya pengaruh gelombang dan frekuensi osilasi yang signifikan terhadap laju perpindahan panas yang terjadi. Laju perpindahan panas/pendinginan terbaik terjadi pada frekuensi
osilasi yang lebih rendah; dalam penelitian ini pada gelombang Sinusoidal 120 Hz ? Square 80 hz.

ABSTRACT
Nowadays, the conventional fan-based cooling is no longer efective and
applicable. Miniaturization with higher performance of electronic products causes the need for a new cooling system that high thermal efficiency and low energy consumption. Synthetic jet is a new cooling system based on zero netto mass input but non zero momentum. An impinging synthetic jet which has two membranes will oscillate using two variation of sinusoidal and square wave. This research was conducted both in computational and also experimental stage.
Computational stage was conducted by Fluent CFD Fluent software with turbulence model k-w SST with meshing elements Tet/Hybrid type TGrid, while in the experimental the function generators will used to drive the membranes with the variation of sinusoidal and square wave in three oscillation frequencies: 80 hz, 120 hz, and 160 hz at fixed amplitude of 1 m/s. The experimental results show significant effect of wave and oscillation frequency on the heat transfer rate
that occured. The best heat transfer rate / cooling effect occurs at a lower oscillation frequency; in this study at Sinusoidal 120 Hz ? Square 80 hz."
Depok: Fakultas Teknik Universitas Indonesia, 2012
S1665
UI - Skripsi Open  Universitas Indonesia Library
cover
Ahlul Halli
"Penanganan beban thermal pada dunia industri sangat diperlukan. Sistem alat penukar kalor bisa dikembangkan pada sisi fluida yang digunakan dan desain pipa yang digunakan. Respon dalam bidang thermal adalah maraknya kembali perhatian akan pentingnya alat penukar kalor (heat exchanger). Sebuah alat penukar kalor yang baik harus ditunjang oleh koefesien perpindahan panas yang baik. Koefesien perpindahan panas sendiri di pengaruhi oleh bilangan Reynolds. Dalam penelitian ini, dilakukan rancang bangun sebuah alat penukar kalor tipe double pipe dengan variasi pada pipa air panas, dimana pada pipa luar adalah pipa baja karbon memiliki koefisien perpindahan kalor konduksi 54 W/m.K dan memiliki dimensi panjang pipa 1 m, diameter luar (Ø out) 88.6 mm, dan diameter. dalam (Ø in) 85 mm dan pipa dalam adalah pipa baja karbon memiliki koefisien perpindahan kalor konduksi 54 W/m.K dan memiliki dimensi panjang pipa 1.2 m, diameter luar (Ø out) 30 mm, dan diameter dalam (Ø in) 28 mm. Bedasarkan pengujian didapatkan grafik kenaikan nilai koefisien perpindahan kalor sebanding dengan kenaikan bilangan Reynolds. Profil kotak memiliki nilai koefisien perpindahan panas yang lebih tinggi jika dibandingkan dengan profil bulat. Pada perbedaan jenis aliran sangat berpengaruh terhadap nilai koefisien perpindahan kalor profil bulat, sedangkan pada profil kotak tidak begitu terlihat perbedaannya.

Handling of thermal load on the industrial world is indispensable. Heat exchanger system can be developed on the side of the fluid used and the design of pipe used. Response in the thermal field is widespread concern about the importance of reheat exchanger (heat exchanger). A good heat exchanger must be supported by a good heat transfer coefficient. Heat transfer coefficient itself is influenced by the Reynolds number. In this study, carried out design and construction of an appliance type double pipe heat exchanger with a variation on the hot water pipes, where the outer pipe is carbon steel pipe has a conduction heat transfer coefficient of 54 W / mK and has dimensions of 1 m length of pipe, outer diameter (Ø out) 88.6 mm, and diameter in (Ø in) 85 mm and pipe in carbon steel pipe is a conduction heat transfer coefficient of 54 W / mK and has dimensions of 1.2 m length of pipe, outer diameter (Ø out) 30 mm, and diameter in (Ø in) 28 mm. Based on the obtained testing the graph increases the heat transfer coefficient is proportional to the increase in Reynolds number. Profiles box has a heat transfer coefficient values are higher if compared to the rounded profile. In different types of flow greatly affect the heat transfer coefficient value rounded profile, whereas the profile box is not so pronounced.
"
Depok: Fakultas Teknik Universitas Indonesia, 2012
S1699
UI - Skripsi Open  Universitas Indonesia Library
cover
Hausen, Helmuth
New York : McGraw-Hill, 1983
536.2 HAU h
Buku Teks SO  Universitas Indonesia Library
cover
Helmi Dadang Ardiansyah
"ABSTRAK
Karaketeristik didih alir R-290 menjadi hal yang penting untuk diteliti setelah R-22 mulai dibatasi, karakteristik ini pertukaran kalor, penurunan tekanan, dan pola aliran yang diharapkan dapat menggantikan posisi R-22 dengan R-290 sebagai media pendingin berbahan refrijeran alami. Dalam percobaan aliran didih R-290 dan R-22 sebagai pembanding dilakukan dalam pipa konvensional yang masih banyak digunakan dalam industri dan sistem pendingin rumah tangga. Variasi fluks kalor dari 5.09 kW/m2 sampai 19.03 kW/m2, fluks massa dari 339.74 kg/m2.s sampai 751.74 kg/m2.s dan temperatur saturasi 5.59 oC sampai 18.12 oC untuk R-22 dan sedangkan R-290 dari 114.91 kg/m2.s sampai 637.63 kg/m2.s dan temperatur saturasi dari 4.77 oC sampai 16.45 oC dengan fluks kalor yang sama dengan R-22. Hasil yang didapat adalah penurunan tekanan dipengaruhi oleh fluks kalor, fluks massa dan temperatur saturasi serta R-290 mempunyai penurunan tekanan lebih rendah dibanding R-22. Sedangkan untuk perpindahan kalor, variasi fluks massa menunjukkan tidak ada perubahan baik untuk R-22 dan R-290. Persamaan prediksi Lokhart-Martinelli (1949) hasil yang paling baik untuk penurunan tekanan eksperimen. Kandlikar (1990) mempunyai prediksi paling baik untuk R-22. Untuk pola aliran dibandingkan antara observasi langsung dengan prediksi pola aliran dari Wojtan et al (2005) dan Wang et al (1997).

ABSTRACT
The characteristic of flow boiling R-290 is very important immediately to observeinstead of R-22 was limited, there are such as heat transfer, pressure drop flow boiling and flow pattern that are hoped can change R-22 into R-290 as natular refrigeration. The experiment of flow boiling R-290 and R-22 as comparable was conducted in conventional channel which was used industry. Variation of heat flux was strarted from 5.09 kW/m2to 19.03 kW/m2, Mass flux was 339.74 kg/m2.s to 751.74 kg/m2.s and saturation temperature was 5.59 oC to 18.12 oC for R-22 and R-290 was 114.91 kg/m2.s to 637.63 kg/m2.s and saturation temperatur was4.77 oC to 16.45 oC within heat flux sas big as R-22. The result given interesting value to deeply observation later. Pressure drop was depended by heat flux, mass flux and saturation temperatur and The experiment admitted that R-290 has pressure drop lower than R-22. Mass flux lower slightly changed on heat transfer coefficient for R-22 and R-290. Lokhart-Martinelli (1949) given good prediction on pressure drop data experiment and Kandlikar (1990) has smaller error for prediction of heat transfer flow boiling. This paper presented comparation of flow pattern form Wojtan et al (2005) and Wang et al (1997)."
Fakultas Teknik Universitas Indonesia, 2013
T35450
UI - Tesis Membership  Universitas Indonesia Library
cover
Sambas Prasetya
"ABSTRAK
Skripsi ini membahas mengenai koefisien perpindahan kalor aliran evaporasi dua
fasa refrigrant R-22 pada kanal mini horizontal. Dimana flux kalor yang diberikan
pada test section besarnya dapat divariasikan mulai dari 5 kW/m2 s/d 15 kW/m2.
Untuk bagian test section terbuat dari pipa stainless steel dengan diameter dalam 3
mm, diameter luar 5 mm dan panjang 1000 mm yang diberikan flux kalor yang
seragam disepanjang pipa tersebut dengan mengalirkan arus listirk dan
memberikan insulasi pada bagian luar test section untuk meminimalisasi kalor
yang terbuang kelingkungan. Begitu pula dengan t emperatur saturasi divariasikan
-5°C,0°C,5°C dan 10°C. Untuk memperoleh besarnya nilai koefisien perpindahan
kalor aliran dua fasa dilakukan dengan melakukan percobaan dan
membandingkan hasilnya dengan menggunakan simulasi perhitungan dengan
program MATLAB, dimana nantinya diperoleh nilai koefisien perpindahan kalor
hasil pengukuran, perhitungan dengan menggunakan korelasi Chen. Pada aliran
dua fasa, kualitas massa uap memiliki pengaruh yang tidak signifikan pada
koefisien perpindahan kalor pada daerah kualitas rendah akan tetapi memiliki
pengaruh yang signifikan pada daerah kualitas yang tinggi. Kenaikan koefisien
perpindahan kalor dipengaruhi oleh heat flux yang diberikan. Dimana semakin
besar heat flux yang diberikan maka koef isien perpindahan kalornya akan semakin
besar pula.

ABSTRACT
This minithesis discuss about heat transfer coefficient of evaporation two phase
flow in horizontal minichannel with refrigerant R -22. Heat flux given to the test
section can be varied from 5 kW/m2 up to 15 kW/m2. The test section was made of
stainless steel tuve with inner diameter of 3 mm, outer diameter of 5 mm and
length 1000 mm which was heated uniformly along the tuve by applying an
electric current and outside of the test section was insulated well to prevent heat
loss to surrounding environment. And also with saturation temperature from
0°C,5°C dan 10°C. To obtain two phase flow heat transfer coefficients were used
simulation of calculation using MATLAB, which later, the value of heat transfer
coefficient obtained were measurent and calculation were used Chen correlation.
In Two-phase flow, mass vapour quality had insignificant effect in the lower
quality región, but had significant effect in the higher quality región to heat
transfer coefficient.. Increasing of heat transfer coefficient ere effected by
addition of heat flux given in certain value. Higher heat flux given will result in
higher value of heat transfer coefficient.."
Fakultas Teknik Universitas Indonesia, 2011
S1789
UI - Skripsi Open  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>