Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 190120 dokumen yang sesuai dengan query
cover
Arie Taruna Mukti
"Baja ASTM A36 merupakan mild carbon steel yang banyak digunakan pada sektor infrastruktur, namun demikian baja karbon memiliki ketahanan korosi yang lebih rendah dibandingkan dengan jenis baja lainnya, yang menyebabkan material ini rentan terhadap korosi dalam lingkungan atmosferik. Oleh sebab itu, untuk meningkatkan ketahanan korosinya, baja ASTM A36 dapat dilapisi dengan glass flake epoxy. Penelitian ini bertujuan untuk mempelajari pengaruh perbedaan metode surface cleaning terhadap kekuatan adhesi glass flake epoxy yang diaplikasikan pada substrat baja tersebut dan ketahanan korosi yang dihasilkannya. Dalam penelitian ini diterapkan 5 (lima) jenis metode surface cleaning yaitu: (i) solvent cleaning, (ii) hand tool cleaning, (iii) power tool cleaning, (iv) power tool to bare metal cleaning, serta (v) abrasive blast cleaning. Selanjutnya, dilakukan proses pengukuran kekasaran permukaan dari masing-masing sampel baja ASTM A36 menggunakan metode field test, sebelum diaplikasikan cat dilakukan pengecekan kondisi lingkungan terlebih dahulu (dry and wet temperature, steel temperature, dew point temperature, serta relative humidity), kemudian glass-flake epoxy diaplikasikan pada permukaan substrat baja menggunakan roller paint brush. Setelah itu, dilakukan pengukuran wet dan dry film thickness. Metode analisis data dilakukan per lima sampel dari masing-masing pengujian yang dilakukan yakni pengujian salt spray, pengujian electrochemical impedance spectroscopy, serta dua pengujian adhesi yaitu pull off adhesion dan tape test test. Hasil penelitian menunjukkan bahwa kemampuan organic coating dipengaruhi oleh perbedaan metode surface cleaning yang diterapkan. Abrasive blast cleaning memiliki ketahanan korosi yang paling baik dengan rata-rata pelebaran (creepage) korosi paling rendah yakni 0.49 mm yang termasuk ke dalam rating number 9, dan kekuatan adhesi rata-rata tertinggi yaitu 3.16 MPa. Dengan demikian dapat disimpulkan bahwa, ketahanan korosi dipengaruhi oleh tingkat kebersihan, sementara kekuatan adhesi dipengaruhi oleh tingkat kekasaran.

ASTM A36 steel is a mild carbon steel that is widely used in the infrastructure sector; however, carbon steel has a lower corrosion resistance compared to other types of steel, which makes this material susceptible to corrosion in atmospheric environments. Therefore, to improve its corrosion resistance, ASTM A36 steel can be coated with glass flake epoxy. This research aims to study the effect of different surface cleaning methods on the adhesion strength of glass flake epoxy applied to the steel substrate and the resulting corrosion resistance. In this research, five types of surface cleaning methods were applied, namely: (i) solvent cleaning; (ii) hand tool cleaning; (iii) power tool cleaning; (iv) power tool to bare metal cleaning; and (v) abrasive blast cleaning. Subsequently, the surface roughness measurement process for each ASTM A36 steel sample was carried out using the field test method. Prior to applying the paint, environmental conditions were checked first (dry and wet temperature, steel temperature, dew point temperature, and relative humidity), and then glass-flake epoxy was applied to the surface of the steel substrate using a roller paint brush. Afterward, wet and dry film thickness measurements were taken. The data analysis method was carried out on five samples from each test carried out, namely salt spray testing, electrochemical impedance spectroscopy testing, and two adhesion tests, namely pull-off adhesion and tape test tests. The results show that the organic coating ability is influenced by the different surface cleaning methods applied. Abrasive blast cleaning has the finest corrosion resistance with the lowest average corrosion creepage of 0.49 mm, which is included in rating number 9. In addition, the resulting average adhesion strength is also high at 3.16 MPa. It can be concluded that corrosion resistance is influenced by the degree of cleanliness, while adhesion strength is influenced by the degree of roughness.
"
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Tubagus Muhammad Dhia Hanif
"Baja ASTM A36 memiliki tingkat keuletan dan ketangguhan yang cendrung tinggi, tetapi baja ini seperti material lainnya tidak akan lepas dari fenomena korosi. Salah satu metode untuk menghambat terjadinya fenomena korosi adalah menggunakan metode pelapisan. Jenis pelapisan yang digunakan pada penelitian ini adalah jenis zinc-rich epoxy. Penelitian ini menerapkan 5 (lima) jenis metode persiapan permukaan yaitu: (i) solvent cleaning, (ii) hand tool cleaning, (iii) power tool cleaning, (iv) abrasive blasting serta (v) power tool to bare metal cleaning. Penelitian ini bertujuan untuk mengetahui pengaruh perbedaan metode persiapan permukaan terhadap ketahanan korosi dan kekuatan adhesi pada baja ASTM A36 yang dilapisi oleh zinc-rich epoxy. Hasil dari penelitian menunjukkan bahwa setiap metode persiapan permukaan menghasilkan tingkat kebersihan dan kekasaran permukaan yang berbeda-beda. Pengujian Electrochemical Impedance Spectroscopy (EIS) menghasilkan nilai error yang bervariasi dan tinggi. Nilai error yang terbaik dimiliki oleh sampel power tool to bare metal dengan nilai error sebesar 5.4582. Sampel yang memiliki ketahanan korosi yang terbaik adalah sampel yang memiliki nilai pelebaran goresan terkecil pada pengujian salt spray. Sampel tersebut dimiliki oleh sampel abrasive blasting, yaitu sebesar 0,22 mm dengan rating number 9. Pengujian X-cut tape tidak dapat membedakan pengaruh dari setiap metode persiapan permukaan. Hasil dari pengujian pull-off menyimpulkan bahwa kekuatan adhesi dari metode abrasive blasting memiliki kekuatan yang tertinggi, yaitu sebesar 2.78 MPa. Dapat disimpulkan bahwa semakin tinggi tingkat kebersihan dan kekasaran permukaan, maka semakin baik performa dari cat zinc-rich epoxy dalam ketahanan korosi dan kekuatan adhesi pada baja ASTM A36. Metode abrasive blasting terbukti sebagai metode persiapan permukaan yang paling optimal untuk mendapatkan ketahanan korosi dan kekuatan adhesi yang terbaik dibandingkan dengan metode persiapan permukaan lainnya.

ASTM A36 steel has a high level of ductility and toughness, but this steel, like other materials, will not be free from corrosion phenomena. One method to inhibit the occurrence of corrosion phenomena is to use the coating method. The type of coating used in this study is a type of zinc-rich epoxy. This study applied 5 (five) types of surface preparation methods, namely: (i) solvent cleaning, (ii) hand tool cleaning, (iii) power tool cleaning, (iv) abrasive blasting and (v) power tool to bare metal cleaning. This study aims to determine the effect of different surface preparation methods on corrosion resistance and adhesion strength of ASTM A36 steel coated with zinc-rich epoxy. The study results show that each surface preparation method produces different levels of cleanliness and surface roughness. Electrochemical Impedance Spectroscopy (EIS) testing produces variable and high error values. The best error value is owned by the power tool to bare metal sample with an error value of 5.4582. The sample that has the best corrosion resistance is the sample that has the smallest scratch-widening value in the salt spray test. The sample belongs to the abrasive blasting sample, which is 0.22 mm with a rating number of 9. X-cut tape testing cannot distinguish the effect of each surface preparation method. The results of the pull-off test concluded that the adhesion strength of the abrasive blasting method had the highest strength, which was 2.78 MPa. It can be concluded that the higher the level of cleanliness and surface roughness, the better the performance of the zinc-rich epoxy paint in corrosion resistance and adhesion strength to ASTM A36 steel. The abrasive blasting method is proven to be the most optimal surface preparation method to obtain the best corrosion resistance and adhesion strength compared to other surface preparation methods.
Dokumen Naskah Lengkap Skripsi:
"
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Daffa Aqila
"Dalam dunia industri, metode perlindungan dilakukan untuk memperpanjang umur pemakaian material dengan tujuan memperlambat laju korosi pada material. Adapun metode perlindungan yang sering digunakan adalah metode pelapisan(coating). Metode pelapisan merupakan metode perlindungan dengan melapisi material substrat menggunakan material pelapis guna mencegah terjadinya kontak antara material substrat dengan lingkungan. Pada penelitian ini, material substrat yang digunakan adalah Baja ASTM A36 dan material pelapis yang digunakan adalah cat Surface Tolerant Epoxy. Adapun variabel bebas yang digunakan pada penelitian ini terletak pada metode preparasi permukaan yang terdiri atas : solvent cleaning, hand tool cleaning, power tool cleaning, power tool to bare metal cleaning, dan abrasive blast cleaning. Perbedaan metode preparasi menghasilkan perbedaan kekasaran dan juga tingkat kebersihan dari permukaaan. Hal tersebut dapat mempengaruhi perubahan sifat mekanis dari material pelapis, seperti ketahanan terhadap korosi dan kekuatan adhesi. Berdasarkan uji ketahanan korosi didapatkan hasil metode abrasive blast cleaning dan power tool to bare metal cleaning menghasilkan sifat tahan korosi tertinggi dikarenakan keduanya memiliki rating number 8 pada hasil pengujian salt spray. Berdasarkan uji kekuatan adhesi didapatkan hasil bahwa metode abrasive blast cleaning juga menghasilkan kekuatan adhesi tertinggi. Kesimpulan ini mengacu pada hasil pengujian tape x-cut dimana sampel tersebut menghasilkan rating number 5A dimana sampel tidak mengalami pengelupasan usai dilakukan pengujian. Selain itu, metode abrasive blast cleaning menghasilkan kekuatan adhesi tertinggi pada pengujian pull-off, yakni 7,16 Mpa. Dengan begitu, metode abrasive blast cleaning menjadi metode preparasi permukaan paling efektif bagi baja ASTM A36 sebelum dilapisi dengan material pelapis. Selain itu, dapat disimpulkan pula bahwa semakin tinggi kekasaran permukaan sampel maka ketahanan korosi maupun kekuatan adhesi yang dihasilkan juga semakin baik.

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand tool cleaning, power tool cleaning, power tool to bare metal cleaning, and abrasive blast cleaning. Different preparation methods result in different roughness and cleanliness of the surface. This can affect changes in the mechanical properties of the coating material, such as corrosion resistance and adhesion strength. Based on the corrosion resistance test, it is found that the abrasive blast cleaning and power tool to bare metal cleaning methods produce the highest corrosion resistance properties because both have a rating number of 8 in the salt spray test results. Based on the adhesion strength test, it is found that the abrasive blast cleaning method also produces the highest adhesion strength. This conclusion refers to the results of the tape x-cut test where the sample produces a rating number 5A where the sample does not experience peeling after testing. In addition, the abrasive blast cleaning method produced the highest adhesion strength in the pull-off test, which was 7.16 Mpa. Thus, the abrasive blast cleaning method is the most effective surface preparation method for ASTM A36 steel before being coated with the coating material. In addition, it can also be concluded that the higher the surface roughness of the sample, the better the corrosion resistance and adhesion strength."
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Astika Kurniawati
"Paint, salah satu jenis organic coating, merupakan zat yang dapat digunakan untuk melindungi baja dari lingkungannya sehingga dapat mencegah proses korosi. Perkembangan teknologi membuat paint dapat diaplikasikan di lingkungan air laut, seperti glass flake epoxy coating yang mengandung pigmen micro glass flake. Namun keberhasilan proteksi dari paint sangat ditentukan oleh preparasi permukaan yang baik. Sehingga diperlukan sistem pelapisan dan preparasi permukaan yang baik.
Tujuan dari penelitian ini ialah untuk mengetahui ketahanan korosi, kekuatan adesi, dan ketahanan termal dari glass flake epoxy coating pada substrat baja karbon. Preparasi permukaan dilakukan dengan pengamplasan dengan variasi grit amplas 100, 150, dan 180. Rasio pencampuran volum antara base dan activator yang digunakan ialah sebesar 2,5:1, 3,5:1, dan 4,5:1.
Ketahanan korosi dari lapisan diketahui melalui pengujian sembur garam selama 96 jam. Sedangkan kekuatan adesi lapisan dengan substrat diketahui melalui pulloff adhesion test (dengan kekuatan tarik maksimal alat sebesar 3,5 N/mm²). Untuk mengetahui ketahanan termal lapisan dilakukan pemanasan pada temperatur 150°C selama 15 menit. Pengamatan metalografi juga dilakukan untuk mengetahui struktur dari lapisan film dan juga lapisan interface antara lapisan film dan substrat baja.
Dari pengujian sembur garam didapat nilai peringkat lebar goresan pada semua sampel uji menurun dari 10 menjadi 9 dengan meningkatnya waktu pemaparan. Sedangkan dari pengujian adesi didapat hasil bahwa kekuatan adesi dari lapisan ialah lebih besar dari 3,5 N/mm² karena tidak ada lapisan film yang terangkat dari substrat baja hingga kekuatan tarik maksimal 3,5 N/mm². Secara visual, lapisan film tidak mengalami kerusakan setelah proses pemanasan.

Paint, one type of organic coatings, is a substance can be used to protect steel from its environment so that corrosion can be prevented. Technology development makes paint can be used in marine environment, like glass flake epoxy coating containing micro glass flake pigment. However, good surface preparation has strong effect in producing successful paint protection. So, there must be a good painting system and a good surface preparation to create a good protection.
This research was conducted to evaluate corrosion resistance, adhesion strength, and thermal resistance of glass flake epoxy coating in steel substrate. Surface preparation was performed by grinding using grinding grit of 100, 150, and 180. Mix ratios of volume between base and activator used were 2,5:1, 3,5:1, and 4,5:1.
The corrosion resistance was known by salt spray test with 96 hours of exposure. The adhesion strength was acquired from pull-off adhesion test (with 3,5 N/mm² maximum tensile strength). The coating was heated in 150°C temperature for 15 minutes to get thermal resistance value of the coating. Metallographic examination was also performed to observe the structure of the coating film and interface layer between the coating film and the substrate.
From the salt spray test, the value of rating number decreased from 10 to 9 with increasing exposure time. The adhesion strength of the coatings was higher than 3,5 N/mm², because there were no failure of all film until 3,5 N/mm² maximal tensile load were applied to the coating. From visual examination, there were no film degradation after heating."
2008
S41721
UI - Skripsi Open  Universitas Indonesia Library
cover
Andri Hermawan
"Salah satu permasalahan penggunaan baja karbon pada anjungan lepas pantai adalah korosi, yang dapat menyebabkan penipisan dan kerusakan pada struktur baja. Oleh karena itu diperlukan perlindungan untuk material baja tersebut agar terjaga dari korosi eksternal sampai waktu yang telah ditentukan. Penelitian ini bertujuan untuk mempelajari mekanisme perlindungan korosi dan mekanisme kelekatan cat epoksi yang ditambahkan serbuk aluminium paduan A356.2, yang diaplikasikan pada material pelat baja karbon ASTM A36 di dalam larutan klorida. Metode pengujian meliputi uji tarik cat, uji gores dan sembur garam, pengamatan makro, pengamatan mikro, SEM dan EDX, uji EIS dan Polarisasi. Hasil penelitian menunjukan sistem pengecatan yang menggunakan campuran epoksi 100 ml yang ditambahkan 50 gram serbuk A356.2 memiliki ketahanan korosi yang tinggi dan campuran serbuk A356.2 dapat berfungsi sebagai material penghalang dari korosi eksternal di lingkungan laut.

One of the problems with the utilization of carbon steel in offshore platforms is corrosion, which can cause thinning and damage to steel structures. Therefore, steel material needs to be protected from external corrosion until a predetermined time. This study aims to investigate the mechanism of corrosion protection and the sticking mechanism of epoxy paint with A356.2 aluminum alloy powder, which was applied to ASTM A36 carbon steel plate material in chloride solution. The test methods include paint tensile test, scratch and salt spray test, micro observation, macro observation, SEM, EDX, EIS test, and Polarization. The results of the research show that painting system containing 100 ml epoxy mixture with addition of 50 grams of A356.2 powder has high corrosion resistance and the powder mixture A356.2 can function as a barrier from external corrosion in marine environment."
Depok: Fakultas Teknik Universitas Indonesia, 2019
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Ghufran Mahfuzh
"Pelapisan merupakan salah satu cara yang paling umum digunakan untuk menghindari terjadinya korosi pada baja karbon rendah. Namun sering terjadi kegagalan pada pelapisan ini dikarenakan daya lekat cat yang kurang baik serta metode preparasi yang kurang tepat. Penelitian ini bertujuan untuk mengetahui pengaruh penambahan metalloam pada cat epoksi primer terhadap ketahanan korosi dan daya lekat nya pada substrat baja karbon rendah.
Untuk menganalisa terhadap ketahanan korosinya maka metode yang dilakukan yaitu uji sembur kabut garam dan untuk daya lekat dilakukan pengujian adhesi. Untuk meningkatkan ketahanan korosi dan daya lekat maka pada cat epoksi primer tersebut ditambahkan metalloam sebesar 5%, 10% dan 15%. Hasil yang didapat yaitu peringkat ketahanan korosi adalah 9 atau sangat baik untuk semua sampel. Kemudian dengan penambahan metalloam maka nilai daya lekat dari cat epoksi primer akan meningkat.

Coating is the most common and easy way to avoid and reduce the corrosion rate of low carbon steel. But failures often happened due to insufficient coating adhesion and low preparation method. This study aimed to understand the effect of adding metalloam additives on prime epoxy coating system to its corrosion resistance and adhesion level.
Salt spray test method is use to analyse the corrosion ressitance rate and adhesion test for its adhesion's level. Metalloam of 5%, 10%, and 15% is added to prime epoxy solvent system to increase the corrosion resistance and adhesion level. The result shows that the corrosion resistance rate is 9 which is very good for every sample. And the prime epoxy adhesion's level is increase with the adding of metalloam.
"
Depok: Fakultas Teknik Universitas Indonesia, 2010
S51541
UI - Skripsi Open  Universitas Indonesia Library
cover
Avronovsky
"Pelapisan merupakan salah satu cara yang paling umum dan mudah digunakan untuk menghindari dan mengurangi terjadinya korosi pada baja karbon rendah. Namun sering terjadi kegagalan pada pelapisan ini dikarenakan daya lekat cat yang kurang baik serta metode preparasii yang kurang tepat. Penelitian ini bertujuan untuk mengetahui pengaruh perlakuan permukaan pada material yang akan dilindungi dengan cat epoksi primer terhadap ketahanan korosi dan daya lekatnya pada substrat baja karbon rendah. Untuk menganalisa terhadap ketahanan korosinya maka metode yang dilakukan yaitu sembur kabut garam dan untuk daya lekat dilakukan pengujian pengujian adhesi. Untuk meningkatkan ketahanan korosi dan daya lekat, maka material benda uji yang akan dilapisi cat epoksi primer dilakukan perlakuan permukaan grit 800, SA 1, dan SA 2,5. Hasil yang didapat yaitu peringkat ketahanan korosi adalah 9 atau sangat baik untuk semua sampel. Kemudian dengan perlakuan permukaan yang tinggi dan permukaan yang lebih kasar akan meningkatkan nilai daya lekat dari cat epoksi primer.

Coating is the most common and easy way to avoid and reduce the corrosion rate of low carbon steel. But failure often happened due to insufficient coating adhesion and low preparation method. This study aimed to understand the effect of surface preparation on prime epoxy coated low carbon material corrosion resistence and its adhesion level. The low carbon material which will be coated with epoxy prime coating is subjected to 800 grade grinding, SA 1, amd SA 2,5 sand-blasting before tested in salt spray machine and adhesion test to analyse the corrosion resistance and the adhesion level. The result shows that the corrosion resistance rating is 9 which is very good for every sample, but more specificly higher surface treatment produce higher roughness levelm higher corrosion resistance, and an increase on prime epoxy adhesion level."
Depok: Fakultas Teknik Universitas Indonesia, 2010
S51543
UI - Skripsi Open  Universitas Indonesia Library
cover
Arham
"Pada penelitian ini, material pelapis komposit epoksi- ZnO disintesis dan permukaannya dimodifikasi menggunakan asam stearat. Partikel ZnO dipreparasi menggunakan metode yang murah, yaitu penghalusan dengan ball to powder ratio (BPR) 5:1, 10:1, and 15:1 kemudian dilakukan invesitgasi pada struktur kristal, sifat wettability, gugus fungsi, ukuran partikel dan sifat ketahanan korosi setelah dilakukan pencampuran pada epoksi dengan variasi komposisi 0%, 3%, 6% dan 9%. Ukuran partikel terkecil dan terbesar didapatkan pada BPR 5:1 dengan ukuran partikel sebesar 189,3 nm dan 910 nm, secara berurutan.
Hasil FTIR menunjukkan bahwa efek hidrofobik didapatkan setelah dilakukan modifikasi pada partikel ZnO akibat gugus fungsi alkil (C-H) dan karboksil asam stearat yang mengganti gugus fungsi hidroksil pada permukaan partikel ZnO. Pengaruh variasi komposisi dan perlakuan modifikasi permukaan mempengaruhi nilai sudut kontak air pada baja yang telah dilapis. Metode Tafel polarisasi dan EIS menunjukkan bahwa penambahan filler maupun modifikasi permukaan mampu menurukan laju korosi.
Hasil uji EIS menujukkan nilai Rct dan Rcoat yang bervariasi tetapi memiliki kecenderungan kenaikan ketika terjadi penambahan komposisi filler ZnO dan penambahan modifikasi permukaan. Dari penelitian ini dapat diketahui bahwa komposisi 6% filler maupun perlakuan modifikasi permukaan mampu meningkatkan resistansi korosi melalu mekanisme barrier dan efek hidrofobik.
Kata kunci: Elektrokimia korosi, Komposit coating, Modifikasi Permukaan, ZnO

In this study, the epoxy-ZnO composite coating material was synthesized and the surface using stearic acid. ZnO particles were prepared using an inexpensive method, namely refining with a ball to powder ratio (BPR) of 5:1, 10:1, and 15:1 then investigated on the crystal structure, wettability properties, functional groups, particle size and resistance properties after being carried out. mixing on epoxy with various compositions of 0%, 3%, 6% and 9%. The smallest and largest sizes were found in BPR:1 with particle sizes of 189.3 nm and 910 nm, respectively.
The FTIR results showed that the hydrophobic effect was obtained after modification of the ZnO particles due to the alkyl (C-H) and carboxyl functional groups of stearic acid replacing the hydroxyl functional groups on the surface of the ZnO particles. The effect of variations in composition and surface modification treatment affects the value of the air contact angle on the coated steel. The Tafel polarization method and EIS showed that the addition of filler and surface modification was able to reduce the corrosion rate.
The results of the EIS test showed that the Rct and Rcoat values varied but had a tendency to increase when ZnO filler composition was added and surface modification was added. From this research, it can be seen that the composition of 6% filler and surface modification treatment can increase corrosion resistance through barrier mechanisms and hydrophobic effects.
Keywords: Electrochemical corrosion, Composite coating, Surface Modification, ZnO
"
Depok: Fakultas Teknik Universitas Indonesia, 2022
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Siti Chodijah
"Penelitian ini dilakukan untuk mengetahui efektifitas pelapisan epoksi pada ketahanan korosi pipa baja di dua tanah yang berbeda. Metode yang digunakan adalah metode kehilangan berat dimana kupon ditanam pada kedalaman 50 cm yang dievaluasi setiap 21 hari dengan ukuran sampel kupon berukuran ± 3cm x 5cm. Hasil yang didapatkan adalah laju korosi baja bare dan baja lapis epoksi di dua tanah pada daerah yang berbeda. Adapun laju korosi pada tanah depok untuk baja bare dan baja lapis eposi adalah 6,17730838 mpy dan (0,08103) mpy. Dan laju korosi pada tanah bekasi untuk baja bare dan baja lapis epoksi adalah 5,7887672 mpy dan 0,0017636 mpy. Laju korosi selain dipengaruhi resistivitas tanah (faktor utama) dimana saling berhubungan dengan ph, moisture content, struktur tanah, sumber air, mikroorganisme serta cuaca/kondisi lingkungan juga persiapan permukaan (daya ikat antara baja dan pelapis) merupakan faktor utama yang mempengaruhi laju korosi suatu baja lapis epoksi.

This research is done to know the effectiveness of epoxy coating on ASTM A53 Carbon steel against soil corrosion in two different soils. Weight loss method is used, where the coupon sized 3 x 5 cm planted at 50cm deep and evaluated every 21 days. The result of this research is the corrosion rate of bare steel and coated epoxy steel in two different areas. The corrosion rate in Depok for bare steel and coated epoxy steel are 6,17730838 mpy and 0,08103 mpy. While, the corrosion rate in Bekasi for bare steel and coated epoxy steel are 5,7887672 mpy dan 0,0017636 mpy. The corrosion rate is affected by soil resistivity, which influenced by pH, moisture content, land/ground structure, source of water, microorganism, condition of environment, and surface preparation (adhesion between steel and coating) represent primary factor influencing corrosion rate of coated epoxy steel and bare steel."
Depok: Fakultas Teknik Universitas Indonesia, 2008
S51077
UI - Skripsi Open  Universitas Indonesia Library
cover
Pasaribu, Robert Parulian Hasudungan
"ABSTRAK
Tesis ini membahas perilaku korosi dari pengelasan dissimilar antara baja karbon ASTM A36 dan baja tahan karat SS316L dengan kawat las E309L menggunakan prosedur pengelasan SMAW dan GTAW untuk dibagian root. Plat baja tahan karat dan baja karbon dengan ketebalan 10 mm dan 15 mm dilas, dipotong, diberi perlakuan panas tempering, dilakukan pengamatan mikrostruktur dan kemudian diuji secara elektrokimia. Pengujian secara elektrokimia meliputi uji electro impedance spectra (EIS), Potentiodynamic Polarization, Cyclic Voltametry. Oleh karena inti las baja tahan karat biasanya lemah terhadap korosi terlokalisasi, maka uji celup korosi sumuran ASTM G48 metode A dilakukan demi pengujian menyeluruh perilaku korosi pada pengelasan dissimilar ini. Hasilnya menunjukkan bahwa proses tempering akan meningkatkan ketahanan korosi pengelasan dissimilar. Pengelasan dissimilar tebal plat 15 mm menunjukkan ketahanan korosi yang lebih lemah dibandingkan plat 10 mm, dimana setelah diamati jumlah weld pass yang lebih banyak pada plat 15 mm mempengaruhi struktur mikro dan ketahanan korosi dari pengelasan dissimilar.

ABSTRACT
The focus of this study was addressed to observe corrosion behavior at dissimilar metal welding between carbon steel ASTM A36 and stainless steel 316L with E309L as weld consumables using SMAW and GTAW procedure at root weld. Stainless steel and carbon steel plate of 10 mm and 15 mm thickness were welded, cut, heat treated (tempered), observed for microstructure and then tested electrochemically. Electrochemical testing included electro impedance spectra (EIS), Potentiodynamic Polarization, Cyclic Voltametry. The core welding of stainless steels are known vulnerable to localized corrosion, hence the pitting corrosion immersion test ASTM G48 method was done for a thorough observation of welding dissimilar corrosion behavior. The results showed that the tempering process improved corrosion resistance of dissimilar weld. It was observed that dissimilar welding of 15 mm thickness was more susceptible than plate 10 mm. It is related to the number of weld passes which affect the microstructure and corrosion resistance of the weld dissimilar.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
T45291
UI - Tesis Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>