Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 12 dokumen yang sesuai dengan query
cover
Ainu Safira Corni
"[ABSTRAK
Penelitian ini mengevaluasi kinerja absorpsi gas CO2 dari campurannya dengan
CH4 melalui membran kontaktor superhidrofobik. Kinerja kontaktor membran
superhidrofobik ini ditinjau dari empat parameter utama dengan variasi laju alir
pelarut DEA (100, 300 dam 500 mL/menit) dan jumlah serat membran kontaktor
(2000 dan 8000). Hasil penelitian ini menunjukkan bahwa kenaikan laju alir pelarut
DEA meningkatkan kinerja kontaktor membran superhidrofobik, dalam hal
koefisien perpindahan massa, fluks dan efisiensi penyerapan CO2. Sedangkan
kenaikan jumlah serat membran akan menurunkan koefisien perpindahan massa
dan fluks CO2. Namun, meningkatkan efisiensi penyerapan CO2 dan acid loading.
Koefisien perpindahan massa dan fluks CO2 tertinggi yang didapatkan pada
penelitian ini berturut-turut adalah 2,31 x 10-4 cm/s dan 7,15 x 10-6 mmol/cm2s pada
laju alir DEA 500 mL/menit dan jumlah serat membran 2000. Sedangkan efisiensi
penyerapan CO2 tertinggi adalah 72% pada laju alir DEA 500 mL/menit dan jumlah
serat membran 8000.
ABSTRACT
This study evaluates performance of CO2 absorption from its mixture with CH4
through membran contactor superhydrophobic. Superhidrophobic membrane
contactor performance is observed using four main parameters by varying the flow
rate of solvent DEA (100, 300 dam 500 mL/min) and the number of fiber membrane
contactors (2000 and 8000). The results showed that increasing DEA solvent flow
rate increase superhidrophobic membrane contactor performance, in terms of mass
transfer coefficient, flux and efficiency removal of CO2. While increasing the
number of fiber membrane will reduce the mass transfer coefficient and CO2 flux.
However, it will increase the efficiency removal of CO2 and acid loading. The
highest mass transfer coefficient and CO2 flux obtained in this study are
respectively 2,31 x 10-4 cm/s and 7,15 x 10-6 mmol/cm2s on DEA flow rate of 500
mL/min and the number of fiber membranes 2000. The highest CO2 absorption
efficiency is 72% at DEA flow rate of 500 mL/min and the number of fiber
membranes 8000.;This study evaluates performance of CO2 absorption from its mixture with CH4
through membran contactor superhydrophobic. Superhidrophobic membrane
contactor performance is observed using four main parameters by varying the flow
rate of solvent DEA (100, 300 dam 500 mL/min) and the number of fiber membrane
contactors (2000 and 8000). The results showed that increasing DEA solvent flow
rate increase superhidrophobic membrane contactor performance, in terms of mass
transfer coefficient, flux and efficiency removal of CO2. While increasing the
number of fiber membrane will reduce the mass transfer coefficient and CO2 flux.
However, it will increase the efficiency removal of CO2 and acid loading. The
highest mass transfer coefficient and CO2 flux obtained in this study are
respectively 2,31 x 10-4 cm/s and 7,15 x 10-6 mmol/cm2s on DEA flow rate of 500
mL/min and the number of fiber membranes 2000. The highest CO2 absorption
efficiency is 72% at DEA flow rate of 500 mL/min and the number of fiber
membranes 8000.;This study evaluates performance of CO2 absorption from its mixture with CH4
through membran contactor superhydrophobic. Superhidrophobic membrane
contactor performance is observed using four main parameters by varying the flow
rate of solvent DEA (100, 300 dam 500 mL/min) and the number of fiber membrane
contactors (2000 and 8000). The results showed that increasing DEA solvent flow
rate increase superhidrophobic membrane contactor performance, in terms of mass
transfer coefficient, flux and efficiency removal of CO2. While increasing the
number of fiber membrane will reduce the mass transfer coefficient and CO2 flux.
However, it will increase the efficiency removal of CO2 and acid loading. The
highest mass transfer coefficient and CO2 flux obtained in this study are
respectively 2,31 x 10-4 cm/s and 7,15 x 10-6 mmol/cm2s on DEA flow rate of 500
mL/min and the number of fiber membranes 2000. The highest CO2 absorption
efficiency is 72% at DEA flow rate of 500 mL/min and the number of fiber
membranes 8000., This study evaluates performance of CO2 absorption from its mixture with CH4
through membran contactor superhydrophobic. Superhidrophobic membrane
contactor performance is observed using four main parameters by varying the flow
rate of solvent DEA (100, 300 dam 500 mL/min) and the number of fiber membrane
contactors (2000 and 8000). The results showed that increasing DEA solvent flow
rate increase superhidrophobic membrane contactor performance, in terms of mass
transfer coefficient, flux and efficiency removal of CO2. While increasing the
number of fiber membrane will reduce the mass transfer coefficient and CO2 flux.
However, it will increase the efficiency removal of CO2 and acid loading. The
highest mass transfer coefficient and CO2 flux obtained in this study are
respectively 2,31 x 10-4 cm/s and 7,15 x 10-6 mmol/cm2s on DEA flow rate of 500
mL/min and the number of fiber membranes 2000. The highest CO2 absorption
efficiency is 72% at DEA flow rate of 500 mL/min and the number of fiber
membranes 8000.]"
Fakultas Teknik Universitas Indonesia, 2016
S62292
UI - Skripsi Membership  Universitas Indonesia Library
cover
Angeline Paramitha
"Teknologi alternatif yang potensial untuk pemisahan CO2 dari gas alam adalah kontaktor membran. Teknologi tersebut terus dikembangkan sampai sekarang karena kontaktor membran memiliki kekurangan seperti selektivitas yang semakin lama semakin menurun. Pada kali ini, pemisahan CO2 dari gas alam akan dilakukan dengan pelarut fisika, yaitu PEG. Pemisahan gas dengan pelarut fisika dapat memberikan keuntungan, dapat menghasilkan selektivitas yang cukup tinggi terhadap CO2 serta lebih tidak korosif dibandingkan dengan pelarut kimia. Ada tiga buah jumlah serat membran yang digunakan, yaitu 1000, 3000, 5000. Laju alir pelarut divariasikan dari 100-500 cm3/s. Konsentrasi pelarut divariasikan dari 5-20 b/v. Laju alir gas yang digunakan tetap yaitu sebesar 305 mL/menit. Penelitian dilakukan pada tekanan dan temperatur ambien. Gas yang digunakan dalam penelitian ini adalah campuran gas sintetik CO2 dan CH4 dengan komposisi masing-masing 30 dan 70.
Berdasarkan penelitian, didapatkan jumlah CO2 terabsorpsi mencapai 1,07 x 10-5 mol/s dan efisiensi penyerapan mencapai 12,44 . Koefisien dan fluks perpindahan massa masing-masing mencapai 4,47 x 10-7 m/s dan 2,05 x 10-5 mol/m2.s, serta acid loading mencapai 1,3 x 10-2 mol CO2/mol PEG untuk variasi laju alir dan jumlah serat membran. Sedangkan untuk variasi konsentrasi, kondisi optimumnya adalah PEG 10 b/v.

Alternative technology for CO2 separation is a membrane contactor. This technology continuous to be developed untul now to overcome the weaknesses of the membran itself such as the selectivity progressively decreased as the time goes by. The present study will be done with a physical solvent, PEG. Gas separation with physical solvent provides benefits such as it can produce sufficiently high selectivity towards CO2 and less corrosive than the chemical solvents. There are 3 total membrane fiber that we used, 1000, 3000, and 5000. The solvent flow rate varied from 100 500 cm3 s. Solvent concentration varied from 5 20 wt. The gas flow rate used remains at 305 mL min. The study was conducted at ambient pressure and temperature. The gas used in this study is a synthetic gas mixture of CO2 and CH4 with the composition of their respective 30 and 70.
Based on research, it was obtained the amount of CO2 absorbed reached 1.07 x 10 5 mol s and absorption efficiency reached 12.44 . Mass transfer coefficient and flux respectively reached 4.47 x 10 7 m s and 2.05 x 10 5 mol m2.s, as well as acid loading of 1.3 x 10 2 mol CO2 mol PEG for the variation of solvent flow rate and total membrane fiber. Whereas for the concentration variation, the optimum condition was PEG 10 wt.
"
Depok: Fakultas Teknik Universitas Indonesia, 2017
S66498
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muhammad Fatah Karyadi
"Penelitian ini mengevaluasi kinerja absorpsi gas CO2 melalui membran kontaktor superhidrofobik. Kinerja kontaktor membran superhidrofobik ini ditinjau dari empat parameter utama dengan variasi laju alir pelarut Air (100, 150, 200, 250, 300, 400 dan 500 mL/menit) dan jumlah serat membran kontaktor (2000, 4000 dan 6000). Hasil penelitian ini menunjukkan bahwa kenaikan laju alir pelarut Air meningkatkan kinerja kontaktor membran superhidrofobik, dalam hal koefisien perpindahan massa, fluks dan efisiensi penyerapan CO2. Kenaikan jumlah serat membran juga akan meningkatkan koefisien perpindahan massa dan fluks CO2.
Koefisien perpindahan massa dan fluks CO2 tertinggi yang didapatkan pada penelitian ini berturut-turut adalah 1,69 x 10-4 cm/s dan 1,7 x 10-5 mmol/cm2s pada laju alir Air 500 mL/menit dan jumlah serat membran 6000. Sedangkan efisiensi penyerapan CO2 tertinggi adalah 29,5% pada laju alir Air 500 mL/menit juga pada jumlah serat membran 6000.

This study evaluated the performance of absorption of CO2 through the superhydrophobic contactor membrane. Superhydrophobic contactor membrane performance is evaluated from four main parameters with the variation of solvent flow rates of water (100, 150, 200, 250, 300, 400 and 500 mL/min) and the amount of contactors membrane fibers (2000, 4000, and 6000). The results of this study indicate that the increase in the flow rate of the water solvent, increases superhydrophobic contactor membranes performance in terms of mass transfer coefficient, flux, and the efficiency CO2 absorption. The increase in the number of membrane fibers also increases the mass transfer coefficient and CO2 flux.
The mass transfer coefficient and the highest CO2 flux were obtained in this study are 1.69 x 10-4 cm/s and 1.7 x 10-5 mmol/cm2s respectively when water flow rate is 500 mL/min and the amount of fiber membranes is 6000. The highest CO2 absorption efficiency is 29.5% when water flow rate is 500 mL/min and the amount of membrane fiber is 6000.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S69957
UI - Skripsi Membership  Universitas Indonesia Library
cover
Stephanie Shabanindita
"Nitrogen oksida NOx merupakan salah satu gas yang sangat berbahaya karena sifatnya yang beracun. Salah satu kandungannya, yaitu Dinitrogen Monoksida merupakan gas rumah kaca yang dengan potensi pemanasan global yang sangat besar. Untuk mengatasinya, telah muncul teknologi absorpsi menggunakan kontaktor membran. Kontaktor membran juga mempunyai keunggulan seperti rasio luas kontak dan volum peralatan yang tinggi. Proses absorpsi berlangsung dengan cara melarutkannya dalam absorben yang merupakan campuran oksidator, H2O2 dan HNO3. Variabel bebas yang diuji adalah laju alir absorben antara 100 ndash; 500 cm3/menit serta jumlah serat membrane 2000, 4000, dan 6000.
Pada penelitian ini diketahui bahwa nilai koefisien perpindahan massa, fluks, jumlah N2O terserap, efisiensi penyerapan, dan penurunan tekanan semakin meningkat dengan meningkatnya laju alir pelarut. Sebaliknya, jumlah N2O loading akan semakin kecil. Selain itu, nilai koefisien dan fluks perpindahan massa menurun dengan bertambahnya jumlah serat membran. Sedangkan, jumlah N2O terserap, efisiensi penyerapan dan N2O loading malah akan meningkat.

Nitrogen oxide NOx is a dangerous gas due to its toxic nature. One of it, namely Dinitrogen Monoxide is a greenhouse gas with high global warming potential. Absorption using membrane contactros is develop to overcome these problems. Another advantages is the high ratio of contact area and equipment volume. The absorption process occurs by dissolving it in the absorbent which is a mixture of oxidizer, H2O2 and HNO3. The independent variables tested were absorbent flow rate between 100 500 cm3 min and number of membrane fibers 2000, 4000, and 6000.
In this research, is obtained that the mass transfer coefficient, flux, N2O absorb, absorption efficiency, and pressure decrease is increasing as solvent flow rate increasing. Conversely, N2O loading is decreasing. In addition, coefficient and mass transfer flux value is decreasing as the increasing number of membrane fibers. Meanwhile, the N2O absorb, absorption efficiency and N2O loading is increasing.
"
Depok: Fakultas Teknik Universitas Indonesia, 2017
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Juan
"[ABSTRAK
Tujuan dari pelaksanaan penelitian ini adalah untuk menguji performa penyerapan gas CO2 dengan menggunakan kontaktor membran superhidrofobik. Adapun variasi yang diuji pada penelitian ini adalah pengaruh laju alir gas CO2 (160, 240, dan 320 mL/menit) dan jumlah serat membran kontaktor (2000, 4000, dan 6000). Pada penelitian ini, didapatkan hasil yaitu peningkatan dari laju alir gas umpan menurunkan efisiensi dari proses, namun meningkatkan kapasitas penyerapan dan koefisien perpindahan massa secara menyeluruh. Pada peningkatan jumlah membran, terjadi peningkatan untuk nilai efisiensi, kapasitas penyerapan, dan koefisien perpindahan massa secara menyeluruh. Nilai efisiensi penyerapan tertinggi tercapai sebesar 29% pada laju alir gas umpan sebesar 160 mL/menit dan jumlah serat membran sebesar 6000. Nilai koefisien perpindahan massa dan kapasitas penyerapan tertinggi adalah 1,14x10-4 cm/s dan 0.045 mmol pada laju alir gas 320mL/menit dan jumlah serat membran sebesar 6000.
ABStRACT
The purpose of this experiment is to examine the performance of superhydrophobic contactor in the absorption of CO2 using water. The variation tested in this experiment is the CO2 gas flow rate (160, 240, 320 mL/min) and the number of fiber modules (2000, 4000, and 6000). The results obtained from this experiment is, the increasement of gas flow rate reduces the absorption efficiency, and increases the absorption capacity and the overall mass transfer coefficient. As the number of fibers increases, the efficiency, overall mass transfer coefficient, and absorption capacity also increases. The maximum value for efficiency is 29% and obtained for 160 mL/min gas flow rate and 6000 module fibers. The maximum value for overall mass transfer coefficient and absorption capacity are 1.14x10-4 cm/s and 0.045 mmol respectively for 320 mL/min gas flow rate and 6000 number module.;The purpose of this experiment is to examine the performance of superhydrophobic contactor in the absorption of CO2 using water. The variation tested in this experiment is the CO2 gas flow rate (160, 240, 320 mL/min) and the number of fiber modules (2000, 4000, and 6000). The results obtained from this experiment is, the increasement of gas flow rate reduces the absorption efficiency, and increases the absorption capacity and the overall mass transfer coefficient. As the number of fibers increases, the efficiency, overall mass transfer coefficient, and absorption capacity also increases. The maximum value for efficiency is 29% and obtained for 160 mL/min gas flow rate and 6000 module fibers. The maximum value for overall mass transfer coefficient and absorption capacity are 1.14x10-4 cm/s and 0.045 mmol respectively for 320 mL/min gas flow rate and 6000 number module., The purpose of this experiment is to examine the performance of superhydrophobic contactor in the absorption of CO2 using water. The variation tested in this experiment is the CO2 gas flow rate (160, 240, 320 mL/min) and the number of fiber modules (2000, 4000, and 6000). The results obtained from this experiment is, the increasement of gas flow rate reduces the absorption efficiency, and increases the absorption capacity and the overall mass transfer coefficient. As the number of fibers increases, the efficiency, overall mass transfer coefficient, and absorption capacity also increases. The maximum value for efficiency is 29% and obtained for 160 mL/min gas flow rate and 6000 module fibers. The maximum value for overall mass transfer coefficient and absorption capacity are 1.14x10-4 cm/s and 0.045 mmol respectively for 320 mL/min gas flow rate and 6000 number module.]"
2016: Fakultas Teknik Universitas Indonesia, 2016
S62296
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rexy Darmawan
"Penyerapan gas CO2 memiliki peran yang vital dalam industri gas alam. Teknologi alternatif untuk proses penyerapan CO2 ialah kontaktor membran serat berongga. Teknologi kontaktor membran ini dapat mengatasi kelemahan yang dimiliki kolom konvensional. Namun dalam prakteknya kontaktor membran masih memiliki kekurangan seperti permasalahan pembasahan membran oleh pelarut. Oleh karena itu penelitian ini akan menguji pengaruh laju alir pelarut dan jumlah serat membran dalam kinerja penyerapan gas CO2 murni melalui kontaktor membran serat berongga dengan bahan material membran bersifat superhidrofobik. Pelarut yang digunakan dalam penelitian ini adalah larutan DEA 5% volum. Variabel bebas yang digunakan pada penelitian ini ialah laju pelarut dan jumlah serat membran. Laju pelarut yang digunakan antara 100-500 cm3/menit, sedangkan jumlah serat membran 2000, 4000 dan 6000. Setiap percobaan dilakukan pada laju gas CO2 sebesar 240 cm3/menit. Parameter kinerja perpindahan massa yang dihasilkan pada penelitian ini yaitu efisiensi penyerapan 56%, laju CO2 terabsorpsi 9x10-2 mmol/s, koefisien perpindahan massa 6x10-4 cm/s, fluks CO2 1,85x--5 mmol/cm2.s, serta acid loading 9,5x10-2.

The absorption of CO2 gas has a vital role in the natural gas industry. A promising alternative technology that overcome the disadvantages of conventional gas absorption is hollow fiber membrane contactor. However, in practice, contactor membrane still has problem such as wetting membrane by the solvent. Therefore this study evaluates the effect of solvent flow rate and the number of fibers in pure CO2 gas absorption performance through superhydrofobic hollow fiber membrane contactor using DEA 5%-volume as solvent. The abosrbent that we used in this research is diethanolamine (DEA) with the concentration 5 %-v. Independent variables in this research are solvent flow rate and the number of fibers. Solvent flow rate that we used between 100-500 cm3/minute, and for the amount of fibers are 2000, 4000 and 6000. Each of the experiments that conducted at the CO2 flow rate 240 cm3/minute. Results show that CO2 removal efficiency is 56%, while the rate of CO2 absorption is 9x10-2 mmol/s with overall mass transfer coefficient 6x10-4 cm/s, flux of CO2 absorption is 1.85x10-5 mmol/cm2.s and the acid loading is 9.5x10-2."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S62294
UI - Skripsi Membership  Universitas Indonesia Library
cover
Kevin Alexander
"Karbon dioksida merupakan senyawa pengotor pada gas alam yang dapat mengurangi nilai kalor dan bersifat korosif pada perpipaan. Salah satu metode pemisahan CO2 dari gas alam adalah dengan menggunakan kontaktor membran. Penggunaan kontaktor membran membran superhidrofobik digunakan sebagai media alternatif karena kemampuannya dalam memisahkan CO2 dengan area kontak yang besar pada ukuran yang compact dan mempunyai ketahanan yang baik akan pembahasan yang terjadi oleh larutan absorben.
Tujuan dari penelitian ini adalah mengetahui kinerja kontaktor membran superhidrofobik pada penyerapan gas CO2. Gas yang digunakan dalam penelitian ini adalah campuran gas CO2 dan CH4 sebagai pendekatan dari gas alam yang sesungguhnya. Pada penelitian ini, gas campuran CO2-CH4 dialirkan di bagian shell dan absorben PEG-300 di bagian lumen dalam membran kontaktor. Pengambilan sampel dilakukan setelah 15 menit dan kandungan CO2-CH4 yang tersisa dianalisis dengan Gas Chromatography. Variasi yang dilakukan pada penelitian ini adalah laju alir gas umpan, konsentrasi pelarut PEG-300, dan jumlah serat membran kontaktor.
Bedasarkan penelitian yang dilakukan nilai koefisien perpindahan massa sebesar 0,99-4.29 x 10-7 m/s, fluks 0,39 ndash; 1.05 x 10-5 mol/m2.s, CO2 terabsorpsi 1,94-5.33 x 10-3 mmol/s, CO2 Loading 2.33-6.40 x 10-3, dan efisieni penyerapan sebesar 3.39-7.98.

Carbon dioxide is pollutant in natural gas that could decrease heating value of gas and corrosive due to pipeline gas. One of the separataion method of CO2 from natural gas using membrane contactor. The usage of contactor membrane hidrofobic as alternative method because of a huge surface of contactor area in a compact size. Also it has good resistance from wetting that caused by solvent.
The purpose of this research is to know the performance super hidrofobic membrance contactor on absorbing carbon dioxide gas. Gas that used in this research is the mixed of CO2 and CH4 to approach on real natural gas composition. In this research CO2 CH4 is flown on shell side and the absorbent PEG 300 is in lument site of membrane. Sampling time is done in 15 minutes. After 15 minutes the gas will be analysed using Gas Chromatography. Variation in this research is gas flow rate, PEG 300 solvent concentration, and membrane fibre.
Based on the research mass transfer coefficient is 0,99 4.29 x 10 7 m s, flux is 0,39 ndash 1.05 x 10 5 mol m2.s, absorbed CO2 is 1,94 5.33 x 10 3 mmol s, CO2 Loading 2.33 6.40 x 10 3, dan absorption efficieny is 3.39 7.98.
"
Depok: Fakultas Teknik Universitas Indonesia, 2017
S66454
UI - Skripsi Membership  Universitas Indonesia Library
cover
Meylin
"Gas N2O merupakan salah satu senyawa dari NOx. Senyawa ini satu dari beberapa gas yang dapat menyebabkan gas rumah kaca. Meskipun konsentrasi N2O sedikit diudara tetapi sangat sulit terdekomposisi diudara. Oleh karena itu diperlukan adanya pemisahan NOx dalam bentuk N2O. Kini telah dikembangkan teknologi membran dengan kontaktor serat berongga yang dapat mengatasi permasalahan pencemaran udara. Prinsip dari kontaktor membran ini menggunakan gaya penggerak berupa perbedaan konsentrasi. Pengaruh konsentrasi pelarut merupakan salah satu parameter dalam absorpsi NOx oleh karena itu penelitian ini menguji pengaruh konsentrasi pelarut larutan HNO3 dalam kinerja penyerapan gas NOx melalui kontaktor membran serat berongga superhidrofobik. Dari penelitian ini dilakukan uji perpindahan masa serta untuk analisis gas dilakukan dengan Gas Chromatography. Gas Chormatography digunakan untuk menganalisis kandungan gas NOx yang terserap setelah percobaan. Variabel bebas dari penelitian ini yaitu konsentrasi pelarut HNO3 sebesar 0,5; 1; 1,5; 2M dan serat membran yaitu 2000, 4000, 6000 sedangkan variabel tetap yaitu laju alir gas 0,1 L/menit ,dan konsentrasi H2O2 0,5 wt. Pada penelitian ini didapatkan persen penyerapan N2O, koefisien perpindahan massa fluks perpindahan massa, N2O loading terbesar secara berturut ndash; turut yaitu 89,6 , 4,95x10-6 m/s, 10,2x10-5 mol/m2s, 4,43 x10-2 mol N2O/mol pelarut. Semakin besar laju alir maka semakin besar penurunan tekanan dalam penelitian ini rasio penurunan tekanan berkisar antara 1, 107- 2,04. Kata kunci: absorpsi N2O, hollow fiber contactor membrane, jumlah serat, konsentrasi HNO3, superhidrofobik.

Dinitrogen oxide is one of compound NOx. N2O one of compound NOx which can to make effect global warming. Although concentration N20 is small in the atmosfer but N2O can rsquo t decomposed in air but solute in water. Therefore, we need separation N2O as NOx. Nowdays membran technology have been developed by people to overcome problem in air pollution. The main principle of membrane contactor use gradient concentration as a driving force. In this study to knowing influence concentrations of solvent HNO3 in absorp gas NOx through superhidrophobic hollow fiber membrane contactor. Gas Chromatography is used to analyse concentration gas NOx in sample after research. Independent variable in this study is concentration of HNO3 0,5 1 1.5 2 M and numerous of fibers 2000,4000,6000 meanwhile dependent variable are flow rates gas 0,1 L minute, and concentration of H2O2 0,5 wt. This study aims to see the effects of concentrations of HNO3 and number of fibers in the contactor on the mass transfer coefficient KL , efficiency of absorption R , flukx J , and NOx loading. In this study, the largest percentage of N2O absorption, coefficient of mass transfer, flukx of mass transfer, N2O loading are 89,6 , 4,95x10 6 m s, 10,2x10 5 mol m2s, 4,43 x10 2 moles of N2O mol of solvent. Increasing flow rate will be obtained pressure drop rise. In this research the ratio of pressure drops ranges from 1, 107 2.04. Key Words absorption N2O, amount of fiber, concentration of HNO3, hollow fiber contactor membrane, superhidrophobic "
Depok: Fakultas Teknik Universitas Indonesia, 2017
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Eric Adelwin
"[Gas alam sudah menjadi alternatif bahan bakar maupun digunakan sebagai bahan baku industri. Gas alam terdiri dari senyawa hidrokarbon berupa gas, seperti metana, etana, propana, butana, dan kondensat. Namun gas alam memiliki kandungan pengotor berupa air, nitrogen, karbon dioksida, hidrogen sulfida, dan merkuri yang harus dihilangkan. Teknologi kontaktor membran merupakan salah
satu cara dalam menghilangkan kandungan karbon dioksida yang terdapat di dalam gas alam. Pada penelitian ini digunakan teknologi kontaktor membran serat berongga superhidrofobik dengan menggunakan pelarut DEA. Penelitian ini bertujuan untuk mengetahui persen penyerapan gas karbon dioksida dari pelarut DEA serta untuk mengetahui pengaruh laju alir gas umpan terhadap fenomena perpindahan massa yang terjadi di membran. Dari fenomena perpindahan massa yang terjadi, akan didapatkan kinerja dari kontaktor membran serat berongga superhidrofobik dalam proses absorbsi gas karbon dioksida. Berdasarkan penelitian yang dilakukan, jumlah gas karbon dioksida yang terserap sebesar 0,03128-0,05331 mmol/s untuk modul dengan jumlah serat 8000 dan untuk modul dengan jumlah serat 2000 mampu menyerap gas CO2 sebesar 0,0268-0,02994 mmol/s. Nilai koefisien perpindahan massa yang didapatkan untuk modul dengan jumlah serat 2000 adalah sebesar 1,93x10-4-2,5x10-4 cm/s dan modul dengan jumlah serat 8000 sebesar 9,8x10-5 – 1,44x10-4 cm/s untuk variasi laju alir gas sebesar 170, 255, dan 340 cm3/min dengan laju alir pelarut DEA yang tetap sebesar 500 cm3/min.

Natural gas has been used as alternative fuel or used as industrial raw materials. Natural gas consists of hydrocarbon compounds such as methane, ethane, propane, butane, dan condensats. However, natural gas also consists of impurities such as water, nitrogen, carbon dioxide, hydrogen sulfide, and mercury which have to remove. Membrane contactor technology is one of the methods which is used to remove carbon dioxide contents that contained in natural gas. In this study, we use hollow fiber membrane contactor using DEA as the solvent. The aim of this study is to know the absorption percentage of carbon dioxide and to know the effect of feed gas flow to mass transfer phenomenon which is occurred in membrane contactor. From the mass transfer phenomenon, we will obtain the performance of superhydrophobic hollow fiber membrane contactor in the absorption process. According to this study, the amount of carbon dioxide absorbed are about 0,03128-0,05331 mmol/s for the module with 8000 fibers and for the module with 2000 fibers able to absorb CO2 about 0,0268-0,02994 mmol/s. The value of mass transfer coefficient which yang is obtained from the module with 2000 fibers are 1,93x10-4-2,5x10-4 cm/s and for the module with 8000 fibers are 9,8x10-5-1,44x10-4 cm/s for the variation of the feed gas flow: 170, 255, dan 340 cm3/min with the DEA constant flowrate about 500 cm3/min., Natural gas has been used as alternative fuel or used as industrial raw materials.
Natural gas consists of hydrocarbon compounds such as methane, ethane,
propane, butane, dan condensats. However, natural gas also consists of impurities
such as water, nitrogen, carbon dioxide, hydrogen sulfide, and mercury which
have to remove. Membrane contactor technology is one of the methods which is
used to remove carbon dioxide contents that contained in natural gas. In this
study, we use hollow fiber membrane contactor using DEA as the solvent. The
aim of this study is to know the absorption percentage of carbon dioxide and to
know the effect of feed gas flow to mass transfer phenomenon which is occurred
in membrane contactor. From the mass transfer phenomenon, we will obtain the
performance of superhydrophobic hollow fiber membrane contactor in the
absorption process. According to this study, the amount of carbon dioxide
absorbed are about 0,03128 – 0,05331 mmol/s for the module with 8000 fibers
and for the module with 2000 fibers able to absorb CO2 about 0,0268 – 0,02994
mmol/s. The value of mass transfer coefficient which yang is obtained from the
module with 2000 fibers are 1,93x10-4 – 2,5x10-4 cm/s and for the module with
8000 fibers are 9,8x10-5 – 1,44x10-4 cm/s for the variation of the feed gas flow:
170, 255, dan 340 cm3/min with the DEA constant flowrate about 500 cm3/min.]
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S62295
UI - Skripsi Membership  Universitas Indonesia Library
cover
Ryan Andriant
"Pemisahan gas CO2/N2 memiliki peran yang vital dalam berbagai industri yang memiliki proses pembakaran. Teknologi alternatif untuk proses tersebut ialah kontaktor membran serat berongga karena dapat mengatasi kelemahan pada kolom konvensional, meskipun masih dapat terjadi pembasahan membran oleh pelarut. Oleh karena itu, penelitian ini akan menguji pengaruh konsentrasi dan laju alir pelarut serta jumlah serat membran pada kinerja penyerapan CO2 melalui kontaktor membran serat berongga superhidrofobik. Pelarut yang digunakan yaitu polietilena glikol PEG. Variasi konsentrasi yaitu 5, 10, 15, dan 20 -b/v. Variasi laju alir pelarut yaitu 100, 200, 300, 400, dan 500 cm3/menit. Variasi jumlah serat membran yaitu 1000, 3000, dan 5000. Setiap percobaan dilakukan pada laju alir gas 190 SCCM. Pada uji hidrodinamika, penurunan tekanan maksimal di dalam serat membran yaitu 24,8 kPa dan rasio penurunan tekanan maksimal yaitu 1,69. Konsentrasi pelarut yang optimum yaitu pada rentang 5-10 -b/v untuk kondisi operasi yang digunakan. Parameter kinerja perpindahan massa maksimal yang diperoleh antara lain koefisien perpindahan massa 5,85x10-7 m/s, fluks perpindahan massa 2,11x10-5 mol/m2.s, CO2 loading 9,96x10-3 mol CO2/mol PEG, efisiensi penyerapan 33,27 , dan jumlah CO2 terabsorpsi 5,65x10-6 mol/s.

The separation of CO2 N2 has a vital role in nowadays industries which have combustion process. The alternative technology for that process is hollow fiber membrane contactor because it is able to overcome the disadvantages of conventional column, although there is still wetting phenomenon by the solvent. Therefore, this study will evaluate the effect of solvent concentration and flow rate and also the number of fibers in CO2 absorption performance through superhydrofobic hollow fiber membrane contactor. The abosrbent used is polyethylene glycol PEG. The solvent concentration variation are 5, 10, 15, and 20 w v. The solvent flow rate variation are 100, 200, 300, 400, and 500 mL minute. The number of fibers variation are 1000, 3000, and 5000. Each experiments are being done with gas flow rate of 190 SCCM. At hydrodynamic test, the maximal pressure drop in the fiber is 24,8 kPa and the maximal pressure drop ratio is 1,69. The optimum range for solvent concentration is 5 10 w v for the selected operating condition. Maximal mass transfer parameters calculated are 5,85x10 7 m/s for mass transfer coefficient, 2,11x10 5 mol m2.s for mass transfer flux, 9,96x10 3 mol CO2 mol PEG for CO2 loading, 33,27, for absorption efficiency, and 5,65x10 6 mol s for amount of absorbed CO2."
Depok: Fakultas Teknik Universitas Indonesia, 2017
S66691
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2   >>