Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 24 dokumen yang sesuai dengan query
cover
Rachmat Andika
"Barium Titanate telah diketahui memiliki karakteristik yang dapat dimanfaatkan dalam berbagai aplikasi. Barium Titanate merupakan material dielektrik non-linier yang bebas dari kandungan Plumbum. Konstanta dielektrik dan permitivitas yang tinggi dibandingkan material ferroelektrik lain dan adanya arus bocor yang relatif tinggi menjadikan barium titanate menarik untuk diteliti lebih lanjut. Ion Zirconium merupakan substituent efektif Barium Titanate untuk mengurangi arus bocor dikarenakan ion Zirconium cenderung lebih stabil dibandingkan ion Titanium.
Lapisan tipis barium titanate yang disubstitusi dengan ion Zr(0,08 dan 0,1) dihasilkan melalui metode Chemical Solution Deposition yang dilanjutkan melalui spin coating dan perlakuan panas. Larutan BaZrTiO3 dideposisikan pada substrat Si hingga 3-5 lapisan dengan kecepatan putar 3000 rpm selama 30 s dilanjutkan dengan pirolisis pada 300°C dan annealing pada 700°C-800°C. Karakterisasi pada lapisan tipis BZT menitikberatkan pada sifat kristalografi melalui XRD dan uji histerisis. Uji histerisis dilakukan dengan sumber tegangan AC dengan 20 Vpp pada frekuensi 60 Hz.
Pola XRD menunjukkan adanya peningkatan ukuran kristalit terbesar pada 800°C sekitar 113 nm dengan menggunakan metode Williamson-Hall. Perbedaan Zr pada struktur BaTiO3 menggeser bidang hkl pada 2θ. Dengan jumlah lapisan BaZrTiO3 meningkat, polarisasi pada histerisis ferroelektrik cenderung tetap.

Barium Titanate is well known materials for many applications. It is nonlinear dielectric material and lead free based material, then this material is enviromental friendly. High dielectric constant and permitivity compared with other ferroelectric materials dan the high leakage current make barium titanate more interesting for further development. Zirconium ion is effective substituent of Barium Titanate to reduce leakage current. This is possible because Zirconium ion more stable than Titanium ion.
Barium Titanate thin films Zr-doped(0.08 and 0.1 mol) is produced by Chemical Solution Deposition and continued by spin coating and heat treatment. BaZrTiO3 solution 0.5M is deposited on Si substrate 3-5 layers with rotational speed up to 3000 rpm for 30 s then it was treated by pyrolisis on 300°C and annealing 700°C-900°C. BZT thin films is charaterized by XRD to know its crystallographic properties and hysterisis testing. Hysterisis loop is made by using AC voltage source with 20 Vpp at frequency of 60 Hz.
The XRD curves showed that crystalite size, based on Williamson-Hall calculation, is calculated around 113 nm for heat treatment 800°C. The different of Zr substitution in BaTiO3 structure shifted hkl plane on 2θ. Multilayer of BaZrTiO3 films on 0.1 Zr increase saturate polarization and decrease coersive field. In this case ferroelectric properties of BaZrTiO3 thin films increase, in contrary the low coersive field showed that easily loses its ferroelectric properties.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2013
T35080
UI - Tesis Membership  Universitas Indonesia Library
cover
Nur Intan Pratiwi
"Melalui proses sol-gel, penelitian ini menitikberatkan pada optimasi parameter yang dapat mengarahkan terbentuknya fasa tunggal BTO. Pada studi stirring awal, temperatur 50°C selama 30 menit TiO2 dalam HNO3 memiliki hasil yang lebih baik pada pola difraksi, ditandai dengan komposisi TiO2 kurang dari 2%. Pada rasio antara HNO3 dengan NH4OH sebesar 2:1 (pH asam), temperatur sintering memberikan efek terhadap kristalisasi dari senyawa dasar BTO, yaitu dengan mengurangi fasa lain, seperti Ti2O3 dan TiO2 secara signifikan dari temperature 800°C hingga 900°C selama 2 jam. Selain itu penelitian ini mengindikasikan adanya pengaruh fasa lain terhadap sifat listrik, yaitu terjadi pemisahan antara dua sampel BTO pada frekuensi 10 Hz untuk nilai kapasitansi dan 1 kHz untuk konduktivitas.

This research focused on parameters of optimization which could produced single phase of BTO. TiO2 and HNO3 precursors which stirred at 50°C for 30minutes showed better diffraction patterns, indicated by TiO2 composition less than 2%. In ratio of HNO3 : NH4OH equal to 2:1 (acid condition), the sintering temperature had effect to BTO crytallization, indicated by secondary phase (Ti2O3 and TiO2) significantly decreased with temperature variase between 800°C to 900°C for 2 hours. Furthehhhrmore, this study indicated the existences of secondary phase had effect to electrical properties of samples. Showed by the separation of two BTO samples for capacitance measurment at 10 Hz and conductivity measurment at 1 kHz."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2014
S55582
UI - Skripsi Membership  Universitas Indonesia Library
cover
Hutabarat, Surya Dharma
"Sintesis Li4Ti5O12 telah banyak diteliti karena merupakan material yang menjanjikan sebagai anoda baterai ion lithium dibandingkan dengan anoda konvensional seperti carbon. Preparasi sampel TiO2 dilakukan melalui proses solgel Rw 3,5. Lithium titanat disintesiss dengan metode solid-state dengan variabel perbedaan kadar LiOH untuk mengetahui pengaruhnya terhadap struktur kristal, sifat elektrokimia lithium titanat yang dihasilkan. Sampel yang disinteis terdiri dari 3 jenis yaitu penambahan massa LiOH secara stokiometri, massa LiOH berlebih 50% dari stokiometri dan 100% berlebih dari stokiometri. Sampel dikarakterisasi menggunakan EDS, BET, XRD, SEM, dan UV-VIS.
Hasil penelitian menunjukkan, lithium titanat yang dihasilkan dengan perbandingan kadar LiOH dengan TiO2 secara stokiometri memilki tingkat kecocokan tertinggi, ukuran partikel dan energi celah terkecil dan luas permukaan terbesar bila dibandingkan dengan sampel yang kadar LiOH dibuat berlebih. Pengaruh dari perbedaan kadar LiOH dapat membentuk pengotor TiO2 rutile dan Li2TiO3.

Synthesis of Li4Ti5O12 has been widely studied as a promising material as an anode of lithium ion batteries compared to conventional anodes like carbon. Preparation sample of TiO2 is done through a process sol-gel Rw 3.5. Lithium titanate synthesized by solid-state method with variable of LiOH ratio to determine the their effects on the crystal structure, electrochemical properties of lithium titanate produced. Samples were synthesized consisting of three types, which are the addition of LiOH in stoichiometric, mass excess LiOH 50% and 100% of the stoichiometric. The samples were characterized using EDS, BET, XRD, SEM, and UV-VIS.
The results showed, lithium titanate synthesized by stoichiometric ratio of LiOH and TiO2 have the highest match rate, lowest particle size and energy gap and largest surface area, compared to samples synthesized excessive levels of LiOH. The effect of mass variation of LiOH can make impurities like TiO2 rutile and Li2TiO3.
"
Depok: Fakultas Teknik Universitas Indonesia, 2014
S56947
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muksin, Author
"Litium titanat (Li4Ti5O12) merupakan senyawa yang digunakan sebagai anoda baterai ion litium. Senyawa litium titanat disintesis berdasarkan metode solid state dengan mereaksikan TiO2 xerogel yang dibuat dengan metode sol-gel dan litium oksida (Li2O). Dalam penelitian ini menggunakan tiga variasi penambahan kadar massa litium oksida (Li2O); massa Li2O sesuai stokiometri (0% melebihi stokiometri), 50% massa Li2O melebihi stokiometri dan 100% melebihi nilai stokiometri. Pengaruh dari penambahan kadar massa litium oksida (Li2O) pada struktur, morfologi, dan energi celah pita tersebut diamati. Sampel yang terbentuk diuji dengan menggunakan X-Ray diffraction, scanning electron microscope (SEM) dan UV-Vis spectroscopy.
Hasil penelitian menunjukan bahwa dengan penambahan massa Li2O sesuai stokiometri membentuk senyawa Li4Ti5O12 dan pengotor seperti TiO2 rutile dan Li2TiO3 dengan ukuran kristalit 13,7 nm, ukuran diameter partikel 0,540 μm band gap energy 3,864 eV, penambahan massa Li2O 50% melebihi stokiometri membentuk senyawa Li2TiO3 dengan ukuran kristalit 7,2 nm, ukuran diameter partikel 1,062 μm dan band gap energy 3,838 eV dan penambahan 100% massa Li2O melebihi stokiometri membentuk Li2TiO3 dengan ukuran kristalit 12,4 nm, ukuran diameter partikel 1,916 μm dan band gap energy 3,778 eV. Senyawa Li4Ti5O12 terbentuk hanya dengan penambahan Li2O sesuai stokiometri. Untuk mensintesis senyawa Li4Ti5O12 bebas dari pengotor mengunakan metode solid state dapat mengacu pada diagram fasa Li2O-TiO2 (29% mol Li2O-71% mol TiO2).

Lithium titanate (Li4Ti5O12) is anode material for application in lithium ion battery. Lithium titanate was synthesized by solid-state method using xerogel TiO2 was prepared by sol–gel process and commercial lithium oxide (Li2O) powder. This research uses 3 various content of lithium oxide (Li2O); 0% Li2O mass excess, 50% Li2O mass excess, and 100% Li2O mass excess. The effect of adding lithium oxide (Li2O) on structure, morphology of particle surface, and band gap energy was examined. Samples were obtained by X-ray diffraction, scanning electron microscope (SEM), ultraviolet visible (UV-Vis).
The results show with adding lithium oxide stoichiometry (0% Li2O excess) produces Li4Ti5O12 and impurities such as rutile TiO2 and Li2TiO3, it produces Li2TiO3 with 50% Li2O excess and it produces Li2TiO3 with 100% Li2O excess. In this research show with appropriate of stochiometry content (0% Li2O excess) produces Li4Ti5O12 with crystallite size is 13,7 nm and impurities namely Li2TiO3 with crystallite size is 22,8 nm and TiO2 with crystallite size 9,14 nm, diameter particle size is 0,540 μm and bandgap energy 3,864 eV. 50% Li2O excess produces Li2TiO3 with crystallite size 7,2 nm, diameter particle size is 1,062 μm and bandgap energy 3,838 eV and with 100% Li2O excess produces Li2TiO3 with crystallite size 12,4 nm, diameter particle size is 1,916 μm and band gap energy is 3,778 eV. The Li4Ti5O12 compound was formed only with appropriate of stoichiometry content. In order to make high purity of Li4Ti5O12 compound on solid state reaction, Li2O-TiO2 phase diagram (29% mol Li2O-71% mol TiO2) can be used as reference.
"
Depok: Fakultas Teknik Universitas Indonesia, 2014
S56740
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sulhajji Jompa
"Penambahan Si yang memiliki sifat glass former pada barium titanat, diharapkan memungkinkan pembuatan bahan amorf berbasis barium titanat sehingga terbentuk bahan murah dengan sifat optika non linear sebagai syarat awal terjadinya efek fotorefraktif. Telah dilakukan analisis tentang pengaruh penambahan 0,5 mol berat Si terhadap struktur kristal, kerapatan elektron dan konstanta dielektrik barium titanat yang disintesis dengan teknik metalurgi serbuk dan perlakuan panas maksimum 950 °C, dari dua kelompok bahan yang berbeda, sampel terbaik didapat dari sintesis 1:1:1 mol berat bahan anal BaTiO3, SiO2 dan BaCO3 yang merupakan reagen dari E-Merck. Difraktogram sinar-X diperoleh dengan k (Co Ka) = 1,7889 A, penambahan secara kontinu pada temperatur kamar dan dianalisis menggunakan paket program kristallografi GSAS dari Amerika Serikat.
Analisis struktur memperlihatkan bahwa bahan terdiri dari 4 fasa ; BaTio,5Sia,5O3 sebagai fasa utama dengan grup ruang tetragonal P4mm (40,87 %). dan tiga fasa pengotor adalah O2Si pada grup ruang tetragonal P42212 (47,29 %). Ba2Si dan BaSi2 masing-masing dengan grup ruang ortorombik Pnma (masing-masing 7,35 % dan 4,49 %). Analisis struktur lebih lanjut terhadap fasa utama memberikan informasi a = 3,991(1) A, c = 4,014(1) A, V = 63,95(5) A x2 = 4,639, Rp = 0,293 Rwp = 0.399.
Analisis kerapatan elektron menunjukkan bahwa bila dibandingkan dengan barium titanat murni yang mempunyai kerapatan elektron berdasarkan observasi dan hasil perhitungan masing-masing adalah p max. 115,129 e A"3 dan 112,467e A-3? pada BaTio,5Sio,5O3 terjadi penambahan kerapatan elektron yang masing-masing adalah adalah p max. 148,9 e A-3 dan 143,8 e A-3.
Hasil pengukuran konstanta dielektrik menunjukkan bahwa terjadi peningkatan konstanta dielektrik pada temperatur kamar sampai 70 3C yaitu pada barium titanat murni konstanta dielektrik Er adalah 597,9 sampai 811,5, dan pada Ba(Ti-Si)03 konstanta dielektrik Er adalah 1562,4 sampai 1712,9.

Barium titanate doped with Si, which is one of a glass farmers, is expected to enable barium titanate based amorphous material synthesis. This material might be further developed in order to have an optical non-linear material, which is a basic characteristic of photo refractive effect. Effect of 0,5 molar weight Si on crystallographic structure, electron density and dielectric constant of barium titanate samples have been analyzed. The samples were synthesized using powder metallurgy method with the constraint that the maximum heat treatment is of 950 °C. The best samples in this study were synthesized with stoichiometric amounts BaTiO3, SiO2 and BaCO3 that the reagents from E-Merck. The X-ray diffractograms, which were obtained with continuous scans and ? (Co Ka) = 1,7889 A at room temperature, were refined using the crystallographic software package GSAS. Structural analysis shows that the crystal are BaTia5SSi055G3 as the main phase with the space group tetragonal P4mm (40,87 %). 02Si with the space group tetragonal P42212 (47,29 %). Ba2Si and BaSi2 with the space orthorhombic Pnma (7,35 % and 4,49 %) as the impurity phase respectively.
Structural analysis from the main phase show that the lattice parameters a = 3,991(1) A, c = 4,014(1) A, the crystal volume V = 63,95(5) A3, the goodness of fit x2 is of 4,639, and the residual parameters Rp and Rwp are of 29,3 % and 39,9 % respectively.
Studies on electron density shows that, as compared to that of pure BaTiO3 with p max. 115,129 e A-3 and 112,467 e A-3 for the observed and the calculated value respectively, there is an increasing electron density at BaTio,5Sio,5O3 with p max. 148,9 e A"3 and 143,8 e A-3 for the observed and the calculated value respectively.
The dielectric constraints measurements at room temperature to 70 °C show that, as compared to that of pure BaTiO3 with dielectric constant Er is of 597,9 to 811,5, there is an increasing of dielectric constant at Ba(Ti-Si)03 with Er is of 1562,4 to 1712,9.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 1999
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Anne Zulfia Syahrial
"Lithium titanate, Li4Ti5O12 (LTO) is a promising candidate as lithium ion battery anode material. In this investigation, LTO was synthesized by a solid state method using TiO2 xerogel prepared by the sol-gel method and lithium carbonate (Li2CO3). Three variations of Li2CO3 content addition in mol% or Li2CO3 molar excess were fabricated, i.e., 0, 50 and 100%, labelled as sample LTO-1, LTO-2 and LTO-3, respectively. The characterizations were made using XRD, FESEM, and BET testing. These were performed to observe the effect of lithium excess addition on structure, morphology, and surface area of the resulting samples. Results showed that the crystallite size and surface area of each sample was 50.80 nm, 17.86 m2/gr for LTO-1; 53.14 nm, 22.53 m2/gr for LTO-2; and 38.09 nm, 16.80 m2/gr for LTO-3. Furthermore, lithium excess caused the formation of impure compound Li2TiO3, while a very small amount of rutile TiO2 was found in LTO-1. A near-pure crystalline Li4Ti5O12 compound was successfully synthesized using the present method with stoichiometric composition with 0% excess, indicating very little Li+ loss during the sintering process."
Depok: Faculty of Engineering, Universitas Indonesia, 2016
UI-IJTECH 7:3 (2016)
Artikel Jurnal  Universitas Indonesia Library
cover
R. Dien Ayoe Anggara
"Telah dibuat keramik timbal zirkonium titanat (PZT) doping aluminium dengan variasi persentasi berat 2% dan 8%. Sampel ditekan 2 ton dan dipanaskan pada suhu 800°C selama 8 jam dan ditahan selama 10 jam dan menjadi bulk, setelah itu membuat larutan lapisan tipis dengan mencampur methoxy ethanol di atas substrat Si(100) dan substrat Pt(200)/Si(100), kemudian diletakan pada spin coating dengan kecepatan putar 3000 rpm selama 30 detik dan dipanaskan pada suhu 900°C selama 8 jam dan ditahan selama 3 jam. Dengan metoda ini diharapkan terbentuk lapisan tipis senyawa PZT doping aluminium di atas substrat Si(100) dan substrat Pt(200)/SiI(100). Seluruh sampel dianalisa dengan difraksi sinar-X (XRD) untuk mengetahui parameter kisi, kemudian mengukur konduktifitas dengan I-V meter.

Lead zirconium titanate (PZT) ceramic have been made a doped by alluminum with the weight percentage varied from 2% and 8%. The sample was pressed at 2 ton and heated at 800°C during 8 hours with holding time in 10 hours and becoming bulk. The processed to make a thin film by mixing with methoxy ethanol then deposited to Si(100) and Pt(200)/Si(100) substrates, and then placed in spin coating apparatus with 3000 rpm during 30s and heated at 900°C during 8 hours with holding time 3 hours. by this method would be expected that we obtain new compounds of PZT doped by those atoms. All the samples were then analized by XRD to recognize a lattice parameter. We further discuss a characteristic of conductivity measurement with I-V meter analyzed."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2007
T21017
UI - Tesis Membership  Universitas Indonesia Library
cover
Shafira Rahma Humairah
"ABSTRAK
Lithium Titanate (Li4Ti5O12) merupakan material anoda digunakan untuk penelitian yang dapat membawa suatu inovasi yang terbaru. Sintesis Li4Ti5O12 telah banyak diteliti karena merupakan material yang menjanjikan sebagai anoda baterai ion lithium dibandingkan dengan anoda konvensional lainnya. Pada penelitian ini dilakukan sintesis Li4Ti5O12 dengan variasi silikon 0%,15%,30%,40% dan penambahan Lithium dimana gunanya untuk mengkompeensasi hilangnya Lithium saat pemrosesan berlangsung. Silikon merupakan material yang memiliki kapasitas penyimpanan yang tinggi. Sehingga dengan ditambahkannya silikon pada material Li4Ti5O12 akan meningkatkan kapasitas dari baterai li-ion. Penelitian ini dimulai dari proses sintesa material Si/Li4Ti5O12. Pada material anoda dilakukan pengujian XRD,. Pada proses sintering terjadi pengecilan porositas dan degasing dan Semakin bertambahnya kadar silikon maka akan semakin kecil luas permukaan butir. kristalinitas TiO2 tidak berubah secara signifikan dan kristalinitas Li4Ti5O12 menurun seiring dengan meningkatnya penambahan silicon dan untuk mengetahui konduktifitas serta impedansi nya dilakukan dengan metode electrochemical impedance spectroscopy

ABSTRACT
Lithium Titanate (Li4Ti5O12) an anode material that brings new innovation Synthesis Li4Ti5O12 has been widely investigated as a promising material as an anode of lithium ion batteries compared to other conventional anode with variation of si (0%,15%,30%,40%). Silicon is a material that has a high storage capacity. So with the addition of silicon on Li4Ti5O12 material will increase the capacity of li-ion battery. This research started from the synthesis process material Li4Ti5O12. the anode material testing XRD,. In the sintering process occurs and shrinkage porosity and degasing The increasing levels of silicon it will be the smaller the surface area of the grain. crystallinity TiO2 did not change significantly and the crystallinity Li4Ti5O12 decreased with increasing addition of silicon. to determine the conductivity and its impedance is done by the method of electrochemical impedance spectroscopy.
"
2016
S62648
UI - Skripsi Membership  Universitas Indonesia Library
cover
Yuceu Endah Sakti
"Perovskite berbasis Barium Titanate (BaTiO3) sangat menarik perhatian dalam dunia riset karena bersifat ferroelektrik dengan konstanta dielektrik yang cukup tinggi dan potensi aplikasinya sebagai material dalam multilayer capasitor (MLCs), PTC thermistor, piezoelectric transducers, dan sebagainya. Beberapa peneliti melaporkan bahwa modifikasi terhadap basis BaTiO3 memperlihatkan perubahan sifat struktur dan sifat listrik seperti kestabilan dan transisi struktur terhadap temperatur, kenaikan dielektrik konstan, penurunan loss dielektrik, dan sebagainya.
Pada penelitian ini, akan dipelajari pengaruh substitusi Sr pada site Ba menjadi perovskite keramik Ba1-xSrxTiO3 dengan nilai x = 0; 0,2; 0,6; 0,8. Sintesis material Ba1-xSrxTiO3 dilakukan dengan metode mechanosynthesis powder dan solid state reaction menggunakan BaCO3, TiO2, dan SrCO3 sebagai precursor utama. Sifat struktur dikarakterisasi menggunakan X-ray Diffraction (XRD). Sifat listrik dikarakterisasi menggunakan elektrometer Keithley 6517A untuk mendapatkan parameter listrik seperti polarisasi spontan, polarisasi saturasi, dan respon terhadap medan listrik.

Barium Titanate (BaTiO3)-perovskite-based materials was paid attention due to they posses high dielectric constant and their application as multilayer capasitor (MLCs), PTC thermistor, piezoelectric transducers materials etc. Several researcher reported that modification in BaTiO3 shows the changes in structural and electrical properties i.e. stability and structural transition with temperature, the increasing of dielectric constant, decreasing of dielectric loss, etc.
In this research, the influence of Sr-substitution on Basite of Ba1-xSrxTiO3 perovskite-ceramics with x=0.0, 0.2, 0.6, and 0.8 was studied. The synthesize process have been done by mechanosynthesis powder and solid state reaction methods using BaCO3, TiO2 and SrCO3 as main precursors. The structural properties was characterized by X-ray Diffraction (XRD). The electrical properties was characterized by electrometer Keithley 6517A in order to obtain the electrical parameters such as spontaneous polarization, saturation polarization, and their responses to electric field."
Depok: Universitas Indonesia, 2008
T49026
UI - Tesis Membership  Universitas Indonesia Library
cover
Simamora, Ebsan
"ABSTRAK
Litium titanat (Li4Ti5O12)/LTO merupakan senyawa yang digunakan sebagai anoda baterai litium ion. Untuk meningkatkan performa baterai litium ion maka dilakukan material komposit pada LTO yaitu LTO nanorod/Sn-grafit. Penelitian ini membahas pengaruh variasi temperatur hidrotermal pada Li4Ti5O12 nanorod dan variasi persen berat timah (Sn) pada Li4Ti5O12 nanorod/Sn -grafit sebagai anoda baterai litium. Variasi temperatur hidrotermal pada sintesis LTO nanorod adalah 2000 C, 2200 C, dan 2400 C. Variasi komposisi persen berat Sn adalah 5%, 7,5%,dan 10%. Sementara persen berat grafit adalah konstan sebesar 10%. Karakterisasi material dilakukan dengan XRD dan SEM. Analisis performa baterai dilakukan dengan pengujian EIS, CV, dan CD. Hasil pengujian XRD menunjukkkan terdapat senyawa LTO nanorod, TiO2 rutile, Li2TiO3, Sn dan grafit. Hasil pengujian SEM menunjukkan tidak ada aglomerasi yang terbentuk dan semakin tinggi temperatur hidrotermal maka bentuk LTO nanorod semakin jelas. Hasil pengujian EIS menunjukkan penambahan persen berat Sn menurunkan nilai konduktivitas. Nilai konduktivitas berbanding terbalik dengan nilai resistivitas (Rct). Nilai konduktivitas tertinggi pada sampel L240Sn5
dengan nilai Rct 58,04 Ω . Hasil pengujian CD menunjukkan bahwa material Sn pada komposit meningkatkan nilai kapasitas baterai. Tetapi penambahan persen berat Sn akan menurunkan nilai kapasitas baterai secara drastis seperti terlihat di nilai C-rates sampel. Hasil pengujian CV menunjukkan nilai kapasitas yang paling tinggi adalah 179,38 Mah/g yaitu pada sampel L220Sn7,5. Nilai sampel paling rendah adalah 130,02 Mah/g pada sampel L200Sn7,5. Tegangan kerja yang paling baik adalah 1,5585 V pada sampel L240Sn5. Tegangan kerja pada sampel ini mendekati tegangan kerja nominal LTO yaitu 1,55V. Variasi Sn pada komposit LTO nanorod/Sn-grafit yang paling baik adalah 5 % (L240Sn5-G10).

ABSTRACT
Lithium titanate (Li4Ti5O12) / LTO is a compound used as an anode for lithium ion batteries. To improve the performance of lithium ion batteries, composite materials are carried out on LTO, namely LTO nanorod / Sn-graphite. This study discusses the effect of hydrothermal temperature variations on Li4Ti5O12 nanorods and variations in the weight percent of Sn on Li4Ti5O12 nanorod / Sn-graphite as an lithium battery anode. Hydrothermal temperature variations in the synthesis of LTO nanorods are 2000 C, 2200 C, and 2400 C. The variation of the composition of weight percent Sn is 5%, 7.5%, and 10%. While graphite weight percent is constant at 10%. Material characterization is done by using XRD and SEM. The performance analysis of the battery is done by testing the EIS, CV, and CD. The XRD test results showed that there are compounds of LTO nanorod, rutile TiO2, Li2TiO3, Sn and graphite. SEM test results show that no agglomerates are formed and the higher the hydrothermal temperature, the more clear the shape of the LTO nanorod. The EIS test results show that the addition of weight percent Sn decreases the conductivity value. The conductivity value is inversely proportional to the resistivity value (Rct). The highest conductivity value in the L240Sn5 sample with an Rct value of 58.04 Ω. The CD test results show that the Sn material on the composite increases the value of the battery capacity. But the addition of weight percent Sn will reduce the value of battery capacity drastically as seen in the sample C-rates. The CV test results show the highest capacity value is 179.38 Mah / g, ie in the L220Sn7.5 sample. The lowest sample value is 130.02 Mah / g in the L200Sn7.5 sample. The best working voltage is 1.5585 V in the L240Sn5 sample. The working voltage in this sample approaches the nominal working voltage of LTO which is 1.55V. The best variation of Sn in LTO nanorod / Sn-graphite composites is 5% (L240Sn5-G10)."
Depok: Fakultas Teknik Universitas Indonesia, 2020
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
<<   1 2 3   >>